Users Manual

FCC ID: I4L-MS6893

Users Manual

Download: PDF

FCCID_971372

MSI MP11BGN (MS-6893)
Wireless 11b/g/n 2T3R MiniPCI Card
User’s Guide

Storage Temperature -20° to 100°C

Humidity 10%-90% (non-condensing)

Power Consumption 802.11b (11Mbps):
660mA@3.3V in continue Tx / 520mA@3.3V in continue Rx

802.11g (54Mbps):
670mA@3.3V in continue Tx / 520mA@3.3V in continue Rx

802.11n Draft 2.0:
HT20MHz:740mA@3.3V in continue Tx / 520mA@3.3V in continue Rx

HT40MHz:740mA@3.3V in continue Tx / 520mA@3.3V in continue Rx

330mA@3.3V in standby mode

Dimension 50.95*59.75*4.5mm

Weight 14g

Operating Voltage 3.3V+/-10%

Output Power (Peak Max) 802.11g (54Mbps): 20.0+/-1 dBm
802.11b (11Mbps): 23.0+/-1 dBm
802.11n Draft 2.0:
HT20MHz: 25.0+/-1 dBm / HT40MHz: 23.0+/-1 dBm

Output Power (Average Max) 802.11g (54Mbps): 15.0+/-1 dBm
802.11b (11Mbps): 15.0+/-1 dBm
802.11n Draft 2.0:
HT20MHz: 15.0+/-1 dBm / HT40MHz: 14.0+/-1 dBm

Error Vector Magnitude (EVM) 802.11g (54Mbps): <-25dB
(Typical Value) 802.11b (11Mbps): <35%
802.11n Draft 2.0: <-28dB

Receiver Sensitivity 802.11b (11Mbps): CCK @ 8% PER = -76 dBm
(Typical Value) 802.11g (54Mbps): OFDM @ 10% PER = -65 dBm
802.11n Draft 2.0:
HT20 @ 10% PER = -64 dBm / HT40 @ 10% PER = -61 dBm

Range Up to 400m (outdoor operating range)

Security 64/128-bit WEP, WPA, WPA2, WPA-PSK, WPA2-PSK, 802.1X, CCX

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may
cause undesired operation.

RF exposure warning ·

This equipment must be installed and operated in accordance with provided instructions
and the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must be
provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.

Document Created: 2008-07-11 16:47:02
Document Modified: 2008-07-11 16:47:02

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC