Test Report

FCC ID: I4L-MS6809

Test Report

Download: PDF
FCCID_337033

Report No. 036L117FI Test Report Product Name : Access Point Model No.: MS-6809 FCC ID.: I4L-MS6809 Applicant : MICRO-STAR INT’L Co., LTD Address : No 69, Li-De st., Jung-He City, Taipei Hsien, Taiwan, R.O.C Date of Receipt : June 10, 2003 Date of Test : June 13, 2003 Report No. : 036L117FI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Page: 1 of 34 Version:1.0

Report No. 036L117FI Test Re port Certification Test Date : June 13, 2003 Report No. : 036L117FI Accredited by NIST (NVLAP) NVLAP Lab Code: 200347-0 Product Name : Access Point Applicant : MICRO-STAR INT’L Co., LTD Address : No 69, Li-De st., Jung-He City, Taipei Hsien, Taiwan, R.O.C Manufacturer : MICRO-STAR INT’L Co., LTD Model No. : MS-6809 FCC ID. : I4L-MS6809 Rated Voltage : AC 120V/60Hz Trade Name : MICRO-STAR Measurement Standard : FCC Part 15 Subpart C Paragraph 15.247 Measurement Procedure : ANSI C63.4: 1992 Test Result : Complied The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Documented By : ( Cordelia Huang ) Tested By : ( John Wu ) Approved By : ( Gene Chang ) Page: 2 of 34 Version:1.0

Report No. 036L117FI TA B L E O F C O N T E N T S Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................6 1.3. Tested System Datails....................................................................................................................7 1.4. Configuration of tested System .....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment............................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................11 2.5. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................14 3.1. Test Equipment............................................................................................................................14 3.2. Test Setup ....................................................................................................................................14 3.3. Limits ..........................................................................................................................................14 3.4. Test Result of Peak Power Output...............................................................................................15 4. Radiated Emission.....................................................................................................................16 4.1. Test Equipment............................................................................................................................16 4.2. Test Setup ....................................................................................................................................16 4.3. Limits ..........................................................................................................................................17 4.4. Test Procedure .............................................................................................................................17 4.5. Test Result of Radiated Emission................................................................................................18 5. Band Edge ..................................................................................................................................24 5.1. Test Equipment............................................................................................................................24 5.2. Test Setup ....................................................................................................................................24 5.3. Limits ..........................................................................................................................................25 5.4. Test Procedure .............................................................................................................................25 5.5. Test Result of Band Edge ............................................................................................................26 6. Occupied Bandwidth.................................................................................................................28 6.1. Test Equipment............................................................................................................................28 6.2. Test Setup ....................................................................................................................................28 6.3. Limits ..........................................................................................................................................28 6.4. Test Result of Occupied Bandwidth ............................................................................................29 7. Power Density ............................................................................................................................30 Page: 3 of 34 Version:1.0

Report No. 036L117FI 7.1. Test Equipment............................................................................................................................30 7.2. Test Setup ....................................................................................................................................30 7.3. Limits ..........................................................................................................................................30 7.4. Test Result of Power Density ......................................................................................................31 8. EMI Reduction Method During Compliance Testing ............................................................32 Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page: 4 of 34 Version:1.0

Report No. 036L117FI 1. GENERAL INFORMATION 1.1. EUT Description Product Name : Access Point Trade Name : MICRO-STAR FCC ID. : I4L-MS6809 Model No. : MS-6809 Frequency Range : 2412MHz to 2462MHz Channel Number : 11 Chip Rate : 1Mbps, 2Mbps, 5.5Mbps, 11Mbps Type of Modulation : Direct Sequence Spread Spectrum Antenna type : Dipole；Patch Antenna Gain : 2.5dBi；2dBi Operator Selection of : By software Operating Frequency Power Adapter : DVE, M/N: DV-1250 Cable In: AC 120V/60Hz/12W Cable Out: DC 12V/500mA UNE OUT:2m Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel 1: 2412 MHz Channel 5: 2432 MHz Channel 9: 2452 MHz Channel 2: 2417 MHz Channel 6: 2437 MHz Channel 10: 2457 MHz Channel 3: 2422 MHz Channel 7: 2442 MHz Channel 11: 2462 MHz Channel 4: 2427 MHz Channel 8: 2447 MHz Note: 1. This device is a 2.4GHz Access Point included a 2.4GHz receiving function, a 2.4GHz transmitting function. 2. Regards to the frequency band operation; the highest rate that was included the lowest、 middle and highest frequency of channel were selected to perform the test, then shown on this report. 3. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15 Subpart C Paragraph 15.247 for spread spectrum devices. 4. This device is a composite device in accordance with Part 15 regulations. The function receiving was measured and made a test report that the report number is 036L117F under Declaration of Conformity. EMI Mode Mode 1: Normal Operation Page: 5 of 34 Version:1.0

Report No. 036L117FI 1.2. Operational Description EUT is a Access Point with 11 channels. This device provided four kind of transmitting speed 1,2,5.5 and 11Mbps. The device of RF carrier is DQPSK, DB PSK and CCK. The device adapts direct sequence spread spectrum modulation. The Connector antenna was scolded on PCB provides diversity function to improve the receiving function. This Broadband Wireless Router is an IEEE 802.11b Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Direst Sequence Spread Spectrum (DSSS) radio transmission, the Broadband Wireless Router transfers data at speeds up to 64/128-bit Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any 802.11b network. Page: 6 of 34 Version:1.0

Report No. 036L117FI 1.3. Tested System Datails The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord (1) Notebook PC ASUS S1300 26NP018680 Non-shielded,1.8m (2) Notebook PC ASUS S1300 24NP035390 Non-shielded,1.8m Signal Cable Type Signal cable Description A. LAN Cable Non-shielded, 3.0m Page: 7 of 34 Version:1.0

Report No. 036L117FI 1.4. Configuration of tested System A EUT Notebook PC (1) Notebook PC (2) 1.5. EUT Exercise Software (1) Setup the EUT and simulators as shown on 1.4 (2) Turn on the power of all equipment. (3) Notebook PC reads data from disk. (4) Data will be transmitting through EUT. (5) The transmitted status will be shown on the monitor. (6) Repeat the above procedure 1.5.3 to 1.5.5 Page: 8 of 34 Version:1.0

Report No. 036L117FI 1.6. Test Facility Ambient conditions in the laboratory: Items Required (IEC 68-1) Actual Temperature (°C) 15-35 20-35 Humidity (%RH) 25-75 50-65 Barometric pressure (mbar) 860-1060 950-1000 Site Description: November 3, 1998 File on Federal Communications Commission FCC Engineering Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Reference 31040/SIT1300F2 August 30, 2001 Accreditation on NVLAP NVLAP Lab Code: 200347-0 Site Name: Quietek Corporation Site Address: No.75-1, Wang-Yeh Valley, Yung-Hsing, Chiung-Lin, Hsin-Chu County, Taiwan, R.O.C. TEL : 886-3-592-8858 / FAX : 886-3-592-8859 E-Mail: service@quietek.com Page: 9 of 34 Version:1.0

Report No. 036L117FI 2. Conducted Emission 2.1. Test Equipment The following test equipment are used during the conducted emission test: Item Instrument Manufacturer Type No./Serial No Last Cal. Remark 1 Test Receiver R&S ESCS 30/825442/17 May, 2003 2 L.I.S.N. R&S ESH3-Z5/825016/6 May, 2003 EUT 3 L.I.S.N. Kyoritsu KNW-407/8-1420-3 May, 2003 Peripherals 4 Pulse Limiter R&S ESH3-Z2 N/A 5 No.2 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year. 2.2. Test Setup Reference Plane Test Receiver 40cm 12dBuV EUT ††† Load ††† LISN LISN LISN Ground Plane 2.3. Limits FCC Part 15 Subpart C Paragraph 15.207 (dBuV) Limit Frequency Limits MHz QP AV 0.15 - 0.50 66-56 56-46 0.50-5.0 56 46 5.0 - 30 60 50 Remarks : In the above table, the tighter limit applies at the band edges. Page: 10 of 34 Version:1.0

Report No. 036L117FI 2.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.4:1992 on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. Page: 11 of 34 Version:1.0

Report No. 036L117FI 2.5. Test Result of Conducted Emission Product : Access Point Test Item : Conducted Emission Power Line : Line 1 Test Mode : Mode 1: Normal Operation Frequency Cable Probe Reading Emission Limits Loss Factor Level Level MHz dB dB dBuV dBuV dBuV =================================================================== Quasi-Peak 0.166 0.21 0.10 45.35 45.66 65.15 0.224 0.21 0.10 43.43 43.74 62.66 0.277 0.21 0.10 40.08 40.39 60.89 * 0.560 0.21 0.10 37.76 38.07 56.00 1.006 0.21 0.10 26.75 27.06 56.00 23.127 0.26 0.50 27.25 28.01 60.00 Average 0.166 0.21 0.10 28.20 28.51 55.15 0.224 0.21 0.10 27.10 27.41 52.66 0.277 0.21 0.10 26.10 26.41 50.89 0.560 0.21 0.10 14.80 15.11 46.00 * 1.006 0.21 0.10 14.40 14.71 46.00 23.127 0.26 0.50 23.80 24.56 50.00 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. “ * ”, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable Loss. Page: 12 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : Conducted Emission Power Line : Line 2 Test Mode : Mode 1: Normal Operation Frequency Cable Probe Reading Emission Limits Loss Factor Level Level MHz dB dB dBuV dBuV dBuV Quasi-Peak 0.225 0.21 0.10 42.73 43.04 62.63 0.279 0.21 0.10 39.26 39.57 60.84 * 0.504 0.21 0.10 38.23 38.54 56.00 0.671 0.21 0.10 23.60 23.91 56.00 1.287 0.21 0.11 26.69 27.01 56.00 23.127 0.26 0.50 29.17 29.93 60.00 Average * 0.225 0.21 0.10 28.90 29.21 52.63 0.279 0.21 0.10 25.10 25.41 50.84 0.504 0.21 0.10 15.80 16.11 46.00 0.671 0.21 0.10 10.50 10.81 46.00 1.287 0.21 0.11 12.50 12.82 46.00 23.127 0.26 0.50 25.70 26.46 50.00 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. “ * ”, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable Loss. Page: 13 of 34 Version:1.0

Report No. 036L117FI 3. Peak Power Output 3.1. Test Equipment The following test equipments are used during the radiated emission tests: Equipment Manufacturer Model No./Serial No. Last Cal. X Spectrum Analyzer Advantest R3162 / 72421194 May, 2003 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year. 2. Mark “X” test instruments are used to measure the final test results. 3.2. Test Setup Conduction Power Measurement RF Cable EUT Spectrum Analyzer SMA Connecter 3.3. Limits The maximum peak power shall be less 1 Watt. Page: 14 of 34 Version:1.0

Report No. 036L117FI 3.4. Test Result of Peak Power Output Product : Access Point Test Item : Peak Power Output Test Site : No.1 OATS Test Mode : Normal Operation Data Speed: 1Mbps Channel No. Frequency(MHz) Measurement Required Limit Result 1 2412 22.30dBm 1Watt= 30 dBm Pass 6 2437 20.06dBm 1Watt= 30 dBm Pass 11 2462 22.68dBm 1Watt= 30 dBm Pass Chancel 1 Chancel 6 Chancel 11 Note: 1. Receiver setting (Peak Detector) : RBW:1MHz; VBW:1MHz; Span:100MHz。 Page: 15 of 34 Version:1.0

Report No. 036L117FI 4. Radiated Emission 4.1. Test Equipment The following test equipment are used during the radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 X Test Receiver R&S ESCS 30 / 825442/14 May, 2003 X Spectrum Analyzer Advantest R3162 / 71720140 May, 2003 X Pre-Amplifier HP 8447D/3307A01812 May, 2003 X Bilog Antenna Chase CBL6112B / 12452 Sep., 2001 X Horn Antenna EM EM6917 / 103325 May, 2003 Site # 2 Test Receiver R&S ESCS 30 / 825442/17 May, 2003 Spectrum Analyzer Advantest R3261C / 71720609 May, 2003 Pre-Amplifier HP 8447D/3307A01814 May, 2003 Bilog Antenna Chase CBL6112B / 2455 Sep., 2001 Horn Antenna EM EM6917 / 103325 May, 2003 Note: 1. All equipments that need to calibrate are with calibration period of 1 year. 2. Mark “X” test instruments are used to measure the final test results. 4.2. Test Setup 3m FRP Dome 1m to 4m The height of board band or Dipole Antenna was scanned from 1M to 4M. The distance between antenna and turn table was 3M regards to the EUT standard adopted. Non-Conducted Table 80cm Fully soldered Metal Ground To Controller Test To Receiver Receiver Page: 16 of 34 Version:1.0

Report No. 036L117FI 4.3. Limits ¾ General Radiated Emission Limits Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 20dB below the level of the fundamental or to the general radiated emission limits in paragraph 15.209, whichever is the lesser attenuation. FCC Part 15 Subpart C Paragraph 15.209 Limits Frequency MHz uV/m @3m dBuV/m@3m 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Remarks : 1. RF Voltage (dBuV) = 20 log RF Voltage (uV) 2. In the Above Table, the tighter limit applies at the band edges. 3. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 4.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.4:1992 on radiated measurement. The additional latch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30 )is 120 kHz, above 1GHz are 1 MHz. The frequency range from 30MHz to 10th harminics is checked. Page: 17 of 34 Version:1.0

Report No. 036L117FI 4.5. Test Result of Radiated Emission Product : Access Point Test Item : Harmonic Radiated Emission Test Site : No.1 OATS Test Mode : Channel 1 Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal Peak Detector: 4824.497 3.29 31.25 19.88 37.65 52.31 21.69 74.00 7236.866 4.53 35.86 21.44 34.29 53.24 20.76 74.00 * 9648.709 5.17 37.85 19.64 30.35 53.74 20.26 74.00 Average Detector: -- Vertical Peak Detector: 4823.763 3.29 31.25 19.88 37.82 52.48 21.52 74.00 7236.866 4.53 35.86 21.44 34.31 53.26 20.74 74.00 * 9647.799 5.17 37.85 19.64 30.37 53.76 20.24 74.00 Average Detector: -- Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. Receiver setting (Peak Detector) : RBW:1MHz; VBW:1MHz; Span:100MHz。 3. Receiver setting (AVG Detector) : RBW:1MHz; VBW:30Hz; Span:20MHz。 4. Emission Level = Reading Level + Probe Factor + Cable Loss – PreAMP. 5. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 18 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : Harmonic Radiated Emission Test Site : No.1 OATS Test Mode : Channel 6 Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal Peak Detector: 4874.320 3.33 31.35 19.86 37.74 52.56 21.44 74.00 7311.240 4.59 35.96 21.50 34.43 53.48 20.52 74.00 * 9748.962 5.32 37.92 19.43 29.77 53.59 20.41 74.00 Average Detector: -- Vertical Peak Detector: 4874.269 3.33 31.35 19.86 37.66 52.48 21.52 74.00 7310.336 4.59 35.96 21.50 34.21 53.26 20.74 74.00 * 9748.087 5.32 37.92 19.43 29.77 53.59 20.41 74.00 Average Detector: -- Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. Receiver setting (Peak Detector) : RBW:1MHz; VBW:1MHz; Span:100MHz。 3. Receiver setting (AVG Detector) : RBW:1MHz; VBW:30Hz; Span:20MHz。 4. Emission Level = Reading Level + Probe Factor + Cable Loss – PreAMP. 5. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 19 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : Harmonic Radiated Emission Test Site : No.1 OATS Test Mode : Channel 11 Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal Peak Detector: 4924.641 3.35 31.45 19.84 37.41 52.38 21.62 74.00 7386.882 4.64 36.09 21.56 34.30 53.47 20.53 74.00 * 9848.641 5.47 37.99 19.22 29.54 53.79 20.21 74.00 Average Detector: -- Vertical Peak Detector: 4924.302 3.35 31.45 19.84 37.45 52.42 21.58 74.00 7386.453 4.64 36.09 21.56 34.34 53.51 20.49 74.00 * 9848.605 5.47 37.99 19.22 29.39 53.64 20.36 74.00 Average Detector: -- Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. Receiver setting (Peak Detector) : RBW:1MHz; VBW:1MHz; Span:100MHz。 3. Receiver setting (AVG Detector) : RBW:1MHz; VBW:30Hz; Span:20MHz。 4. Emission Level = Reading Level + Probe Factor + Cable Loss – PreAMP. 5. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 20 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : General Radiated Emission Test Site : No.1 OATS Test Mode : Mode 1: Normal Operation (Channel 1) Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal 62.437 1.03 5.45 0.00 21.43 27.91 12.09 40.00 137.581 1.42 11.19 0.00 21.22 33.84 9.66 43.50 245.341 1.98 11.16 0.00 15.31 28.45 17.55 46.00 347.194 2.50 12.92 0.00 24.30 39.73 6.27 46.00 435.468 2.96 15.65 0.00 18.51 37.12 8.88 46.00 523.733 3.42 16.44 0.00 19.42 39.28 6.72 46.00 * 611.030 3.87 18.42 0.00 18.15 40.44 5.56 46.00 787.579 4.77 19.21 0.00 14.27 38.25 7.75 46.00 963.145 5.67 20.15 0.00 17.72 43.54 10.46 54.00 Vertical 62.384 1.03 5.58 0.00 21.35 27.97 12.03 40.00 136.487 1.42 10.25 0.00 19.17 30.84 12.66 43.50 245.329 1.98 11.40 0.00 15.40 28.78 17.22 46.00 * 347.195 2.50 13.15 0.00 25.68 41.33 4.67 46.00 435.462 2.96 17.09 0.00 17.03 37.08 8.92 46.00 523.731 3.42 16.79 0.00 16.92 37.13 8.87 46.00 611.038 3.87 19.42 0.00 13.70 36.99 9.01 46.00 787.577 4.77 19.66 0.00 12.17 36.60 9.40 46.00 963.142 5.67 20.24 0.00 10.99 36.90 17.10 54.00 Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. “ * ”, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable Loss. Page: 21 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : General Radiated Emission Test Site : No.1 OATS Test Mode : Mode 1: Normal Operation (Channel 6) Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal 58.659 1.01 5.72 0.00 22.85 29.58 10.42 40.00 126.598 1.37 11.57 0.00 18.64 31.58 11.92 43.50 245.689 1.98 11.26 0.00 20.33 33.58 12.42 46.00 429.927 2.93 15.69 0.00 17.59 36.21 9.79 46.00 618.268 3.90 18.77 0.00 14.91 37.58 8.42 46.00 * 787.918 4.77 19.21 0.00 15.60 39.58 6.42 46.00 Vertical * 53.846 0.99 5.90 0.00 22.46 29.35 10.65 40.00 139.437 1.43 10.30 0.00 19.55 31.28 12.22 43.50 347.367 2.50 13.15 0.00 14.92 30.57 15.43 46.00 538.547 3.49 17.95 0.00 8.40 29.84 16.16 46.00 621.497 3.91 19.27 0.00 11.39 34.57 11.43 46.00 963.579 5.67 20.24 0.00 10.57 36.48 17.52 54.00 Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. “ * ”, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable Loss. Page: 22 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : General Radiated Emission Test Site : No.1 OATS Test Mode : Mode 1: Normal Operation (Channel 11) Frequency Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz dB dB/m dB dBuV dBuV/m dB dBuV/m ============================================================= Horizontal 48.297 0.96 8.36 0.00 19.27 28.59 11.41 40.00 147.597 1.47 10.64 0.00 18.47 30.59 12.91 43.50 347.698 2.51 12.92 0.00 18.04 33.47 12.53 46.00 415.359 2.85 15.67 0.00 16.73 35.26 10.74 46.00 * 632.738 3.97 18.64 0.00 13.87 36.48 9.52 46.00 751.249 4.58 18.49 0.00 12.84 35.91 10.09 46.00 972.518 5.72 20.49 0.00 10.27 36.48 17.52 54.00 Vertical 72.482 1.09 6.60 0.00 23.82 31.51 8.49 40.00 148.448 1.48 9.48 0.00 22.33 33.29 10.21 43.50 218.537 1.84 8.96 0.00 23.41 34.21 11.79 46.00 349.571 2.51 13.30 0.00 21.67 37.48 8.52 46.00 * 523.684 3.42 16.79 0.00 18.40 38.61 7.39 46.00 766.429 4.66 20.32 0.00 12.43 37.41 8.59 46.00 963.517 5.67 20.24 0.00 14.35 40.26 13.74 54.00 Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. “ * ”, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable Loss. Page: 23 of 34 Version:1.0

Report No. 036L117FI 5. Band Edge 5.1. Test Equipment The following test equipments are used during the band edge tests: Equipment Manufacturer Model No./Serial No. Last Cal. X Spectrum Analyzer Advantest R3272 / 72421194 May, 2003 X Test Receiver R&S ESCS 30 / 825442/14 May, 2003 X Spectrum Analyzer Advantest R3162 / 71720140 May, 2003 X Pre-Amplifier HP 8447D/3307A01812 May, 2003 X Bilog Antenna Chase CBL6112B / 12452 Sep., 2001 X Horn Antenna EM EM6917 / 103325 May, 2003 Note: 1. All equipments that need to calibrate are with calibration period of 1 year. 2. Mark “X” test instruments are used to measure the final test results. 5.2. Test Setup RF Conducted Measurement: RF Cable EUT Spectrum Analyzer SMA Connecter RF Radiated Measurement: 3m FRP Dome 1m to 4m The height of board band or Dipole Antenna was scanned from 1M to 4M. The distance between antenna and turn table was 3M regards to the EUT standard adopted. Non-Conducted Table 80cm Fully soldered Metal Ground To Controller Test To Receiver Receiver Page: 24 of 34 Version:1.0

Report No. 036L117FI 5.3. Limits In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Attenuation below the general limits specified in Section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). 5.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.4:1992 on radiated measurement. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30 )is 120 kHz, above 1GHz are 1 MHz. Page: 25 of 34 Version:1.0

Report No. 036L117FI 5.5. Test Result of Band Edge Product : Access Point Test Item : Band Edge Test Site : No.1 OATS Test Mode : Channel 1 RF Radiated Measurement: Frequency Required Limit Channel No. Result (MHz) (dBc) 1 (Horizontal) <2400 >20 Pass 1 (Vertical) <2400 >20 Pass Figure Channel 1: (Horizontal) Figure Channel 1: (Vertical) Page: 26 of 34 Version:1.0

Report No. 036L117FI Product : Access Point Test Item : Band Edge Test Site : No.1 OATS Test Mode : Channel 11 RF Radiated Measurement: (Peak Detector) Reading Probe Cable Emission Frequency PreAMP Limit Channel No. Level Factor Loss Level Result (MHz) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dBuV/m) 11(Horizontal)PK 2489.271 45.03 28.66 4.10 21.18 56.61 74 Pass 11(Horizontal)AVG 2489.271 30.26 28.66 4.10 21.18 41.84 54 Pass 11 (Vertical) PK 2493.285 45.27 28.66 4.10 21.18 56.85 74 Pass 11 (Vertical) AVG 2493.285 20.14 28.66 4.10 21.18 31.72 54 Pass Figure Channel 11: (Horizontal) Figure Channel 11: (Vertical) Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 27 of 34 Version:1.0

Report No. 036L117FI 6. Occupied Bandwidth 6.1. Test Equipment The following test equipments are used during the radiated emission tests: Equipment Manufacturer Model No./Serial No. Last Cal. X Spectrum Analyzer Advantest R3162/ 72421194 May, 2003 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year. 2. Mark “X” test instruments are used to measure the final test results. 6.2. Test Setup RF Cable EUT Spectrum Analyzer SMA Connecter 6.3. Limits The minimum 6dB bandwidth shall be at least 500kHz. Page: 28 of 34 Version:1.0

Report No. 036L117FI 6.4. Test Result of Occupied Bandwidth Product : Access Point Test Item : Occupied Bandwidth Test Site : No.1 OATS Test Mode : Normal Operation Frequency Measurement Level Required Limit Channel No. Result (MHz) (kHz) (kHz) 1 2412 9200 >500 Pass 6 2437 7900 >500 Pass 11 2462 9700 >500 Pass Channel 1: Channel 6 Channel 11: Page: 29 of 34 Version:1.0

Report No. 036L117FI 7. Power Density 7.1. Test Equipment The following test equipments are used during the radiated emission tests: Equipment Manufacturer Model No./Serial No. Last Cal. X Spectrum Analyzer Advantest R3162 / 72421194 May, 2003 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year. 2. Mark “X” test instruments are used to measure the final test results. 7.2. Test Setup RF Cable EUT Spectrum Analyzer SMA Connecter 7.3. Limits The transmitted power density averaged over any 1 second interval shall not be greater +8dBm in any 3kHz bandwidth. Page: 30 of 34 Version:1.0

Report No. 036L117FI 7.4. Test Result of Power Density Product : Access Point Test Item : Power Density Test Site : No.1 OATS Test Mode : Normal Operation Frequency Measurement Level Required Limit Channel No. Result (MHz) (dBm) (dBm) 1 2411.892 -5.84 < 8dBm Pass 6 2436.888 -5.70 < 8dBm Pass 11 2462.300 -9.20 < 8dBm Pass Channel 1: Channel 6 Channel 11: Page: 31 of 34 Version:1.0

Report No. 036L117FI 8. EMI Reduction Method During Compliance Testing No modification was made during testing. Page: 32 of 34 Version:1.0

Report No. 036L117FI Attachment 1: EUT Test Photographs Page: 33 of 34 Version:1.0

Report No. 036L117FI Attachment 2: EUT Detailed Photographs Page: 34 of 34 Version:1.0


Document Created: 2003-06-30 16:46:39
Document Modified: 2003-06-30 16:46:39
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC