RF Report RSE

FCC ID: I28-ZBRZQ3BT

Test Report

Download: PDF
FCCID_4228383

RF TEST REPORT Report No.: FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Supersede Report No.: FCC_RF_SL19011002-ZBR-101A2-BT Applicant : Zebra Technologies Corporation Host Product Name : Thermal Printer Host Model No. : ZD220d, ZD220t, ZD230d, ZD230t, ZP230d Module Model No. : ZQ3BT FCC ID : I28-ZBRZQ3BT IC : 3798B-ZBRZQ3BT FCC 15.247 Test Standard : RSS 247 Issue 2 558074 D01 15.247 Meas Guidance v05r01 Test Method : ANSI C63.10 2013 RSS Gen Issue 5 Dates of test : 02/01/2019-03/26/2019 Issue Date : 03/28/2019 Test Result : ☒ Pass ☐ Fail Equipment complied with the specification [X ] Equipment did not comply with the specification [ ] This Test Report is Issued Under the Authority of: Deon Dai Chen Ge RF Test Engineer Engineer Reviewer This test report may be reproduced in full only Test result presented in this test report is applicable to the tested sample only Issued By: SIEMIC Laboratories 775 Montague Expressway, Milpitas, CA 95035 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 2 of 24 Laboratory Introduction SIEMIC, headquartered in the heart of Silicon Valley, with superior facilities in US and Asia, is one of the leading independent testing and certification facilities providing customers with one-stop shop services for Compliance Testing and Global Certifications. In addition to testing and certification, SIEMIC provides initial design reviews and compliance management throughout a project. Our extensive experience with China, Asia Pacific, North America, European, and International compliance requirements, assures the fastest, most cost effective way to attain regulatory compliance for the global markets. Accreditations for Conformity Assessment Country/Region Accreditation Body Scope USA FCC, A2LA EMC, RF/Wireless, Telecom Canada IC, A2LA, NIST EMC, RF/Wireless, Telecom Taiwan BSMI, NCC, NIST EMC, RF, Telecom, Safety Hong Kong OFTA, NIST RF/Wireless, Telecom Australia NATA, NIST EMC, RF, Telecom, Safety Korea KCC/RRA, NIST EMI, EMS, RF, Telecom, Safety Japan VCCI, JATE, TELEC, RFT EMI, RF/Wireless, Telecom Mexico NOM, COFETEL, Caniety EMC, RF/Wireless, Telecom, Safety Europe A2LA, NIST EMC, RF, Telecom, Safety Israel MOC, NIST EMC, RF, Telecom, Safety Accreditations for Product Certifications Country Accreditation Body Scope USA FCC TCB, NIST EMC, RF, Telecom Canada IC FCB, NIST EMC, RF, Telecom Singapore iDA, NIST EMC, RF, Telecom EU NB EMC & RED Directive Japan MIC (RCB 208) RF, Telecom Hong Kong OFTA (US002) RF, Telecom 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 3 of 24 CONTENTS 1 REPORT REVISION HISTORY .......................................................................................................................................4 2 EXECUTIVE SUMMARY.................................................................................................................................................5 3 CUSTOMER INFORMATION ..........................................................................................................................................5 4 TEST SITE INFORMATION ............................................................................................................................................5 5 MODIFICATION .............................................................................................................................................................5 6 EUT INFORMATION ......................................................................................................................................................6 6.1 EUT Description ........................................................................................................................................................6 6.2 Radio Description ......................................................................................................................................................6 6.3 EUT test modes/configuration Description....................................................................................................................7 7 SUPPORTING EQUIPMENT/SOFTWARE AND CABLING DESCRIPTION .........................................................................8 7.1 Supporting Equipment ...............................................................................................................................................8 7.2 Cabling Description ...................................................................................................................................................8 7.3 Test Software Description ..........................................................................................................................................8 8 TEST SUMMARY ...........................................................................................................................................................9 9 MEASUREMENT UNCERTAINTY ................................................................................................................................. 10 9.1 Radiated Emissions (30MHz to 1GHz) ....................................................................................................................... 10 9.2 Radiated Emissions (1GHz to 40GHz) ....................................................................................................................... 10 9.3 RF conducted measurement..................................................................................................................................... 11 10 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS .................................................................................. 12 10.1 Antenna Requirement.......................................................................................................................................... 12 11 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS .................................................................................. 13 11.1 Conducted emissions .......................................................................................................................................... 13 11.2 Radiated Measurements ...................................................................................................................................... 16 11.2.1 Radiated Measurements 30MHz to 1GHz ......................................................................................................... 16 11.2.2 Radiated Spurious Emissions between 1GHz-25GHz ......................................................................................... 18 ANNEX A. TEST INSTRUMENT ........................................................................................................................................... 22 ANNEX A. SIEMIC ACCREDITATION ................................................................................................................................... 23 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 4 of 24 1 Report Revision History Report No. Report Version Description Issue Date FCC_RF_SL19011002-ZBR-101A2-BT None Original 03/27/2019 FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 1.0 Update 03/28/2019 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 5 of 24 2 Executive Summary The purpose of this test program was to demonstrate compliance of following product Company: Zebra Technologies Corporation Host Product: Thermal Printer Host Model: ZD220d, ZD220t, ZD230d, ZD230t, ZP230d against the current Stipulated Standards. The specified model product stated above has demonstrated compliance with the Stipulated Standard listed on 1st page. This test report covers the radiated emissions requirements of the standards referenced in the report to allow system level approval of the modules in specified Hosts. 3 Customer information Applicant Name : Zebra Technologies Corporation Applicant Address : 3 Overlook Point Lincolnshire, IL 60069, USA Manufacturer Name : Zebra Technologies Corporation Manufacturer Address : 3 Overlook Point Lincolnshire, IL 60069, USA 4 Test site information Lab performing tests : SIEMIC Laboratories Lab Address : 775 Montague Expressway, Milpitas, CA 95035 FCC Test Site No. : 540430 IC Test Site No. : 4842D-2 VCCI Test Site No. : A0133 5 Modification Index Item Description Note - - - - - - - - 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 6 of 24 6 EUT Information 6.1 EUT Description Host Product Name Thermal Printer Host Model No ZD220d, ZD220t, ZD230d, ZD230t, ZP230d Module Model No. ZQ3BT Trade Name Zebra Technologies Corporation Serial No N/A EUT Input Power 24Vdc, 2.5A AC/DC Power Supply Output 24Vdc, 2.5A; 24Vdc, 3.125A, 100-240Vac AC/DC Power Supply Manufacturer/Model FSP: FSP060-RPAC, FSP075-RAAN2; Sanhua: SAWA-31- 25024, SAWA-52-312524 AC/DC Power Supply SN N/A Date of EUT received 1/28/2019 Equipment Class/Category Class B / ITE Clock Frequencies >100MHz Port/Connectors USB, RJ45 Remark N/A 6.2 Radio Description Specifications for Radio: Bluetooth BDR/EDR: Radio Type Bluetooth Operating Frequency 2402MHz-2480MHz Modulation FHSS Channel Spacing 1MHz Antenna Type Chip Antenna Antenna Gain 1.69 dBi (BT) Bluetooth LE: Radio Type Bluetooth (Ver4.0) Operating Frequency 2402MHz-2480MHz Modulation DSSS (LE) Channel Spacing 2MHz (LE) Antenna Type Chip Antenna Antenna Gain 1.69 dBi (BTLE) 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 7 of 24 6.3 EUT test modes/configuration Description Mode Note RF test EUT is set to continuously transmit Note: None Test Item Operating mode Tested antenna port Radiated Spurious Emission Continuous Transmit - Note: - 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 8 of 24 7 Supporting Equipment/Software and cabling Description 7.1 Supporting Equipment Supporting Equipment Item Model Serial Number Manufacturer Note Description 1 Laptop E7440 BJBON12 Dell - 2 60 watt power supply FSP060-RPAC - - - 7.2 Cabling Description Connection Start Connection Stop Length / shielding Info Name Note From I/O Port To I/O Port Length (m) Shielding USB EUT I/O Port Laptop USB 2 Unshielded - - - - - - - - - - - - - - - - - 7.3 Test Software Description Test Item Software Description RF Testing Tool Box Set the Connection with Companion Device 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 9 of 24 8 Test Summary Test Item Test standard Test Method/Procedure Pass / Fail FCC FCC 15.247 FCC 558074 D01 15.247 Meas Guidance v05r01 ☒ Pass Radiated Spurious Emission IC RSS 247 IC RSS Gen ☐ N/A FCC FCC 15.207 FCC ANCI C63.10 ☒ Pass AC Conducted Emission IC RSS GEN IC RSS GEN ☐ N/A 1. All measurement uncertainties are not taken into consideration for all presented test result. Remark 2. The applicant shall ensure frequency stability by showing that an emission is maintained within the band of operation under all normal operating conditions as specified in the user’s manual. 3. Only Radiated Spurious Emission and AC line Conducted was testing for Host configuration. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 10 of 24 9 Measurement Uncertainty 9.1 Radiated Emissions (30MHz to 1GHz) The test is to measure the radiated emissions of the EUT. Some error sources that can contribute to the total uncertainty: - Uncertainty of the receiver - Uncertainty of the antenna - Uncertainty of cables - Uncertainty due to the mismatches - NSA Calibration - Etc., details see the below table Value Probability Sensitivity Expanded Source of Uncertainty Division (dB) Distribution Coefficient Uncertainty Receiver Reading 0.12 Rectangular 1.732 1 0.069284 Cable Insertion Loss 0.21 Normal 2 1 0.105 Filter Insertion Loss 0.25 Normal 2 1 0.125 Antenna Factor 0.65 Normal 2 1 0.325 Receiver CW accuracy 0.5 Rectangular 1.732 1 0.2886836 Pulse Amplitude Response 1.5 Rectangular 1.732 1 0.86605081 PRF Response 1.5 Rectangular 1.732 1 0.86605081 Mismatch Filter - Receiver 0.25 U-Shape 1.414 1 0.1768033 NSA Calibration 4.0 U-Shape 1.414 1 2.8288543 Combined Standard Uncertainty 3.0059131 Expanded Uncertainty (K=2) 6.0118262 The total derived measurement uncertainty is +/- 6.00 dB. 9.2 Radiated Emissions (1GHz to 40GHz) The test is to measure the radiated emissions of the EUT. Some error sources that can contribute to the total uncertainty: - Uncertainty of the receiver - Uncertainty of the antenna - Uncertainty of cables - Uncertainty due to the mismatches - VSWR Calibration - Etc., details see the below table Value Probability Sensitivity Expanded Source of Uncertainty Division (dB) Distribution Coefficient Uncertainty Receiver Reading 0.12 Rectangular 1.732 1 0.0692840 Cable Insertion Loss 0.21 Normal 2 1 0.1050000 Filter Insertion Loss 0.25 Normal 2 1 0.1250000 Antenna Factor 0.65 Normal 2 1 0.3250000 Receiver CW accuracy 0.5 Rectangular 1.732 1 0.2886836 Pulse Amplitude Response 1.5 Rectangular 1.732 1 0.8660508 PRF Response 1.5 Rectangular 1.732 1 0.8660508 Mismatch Filter - Receiver 0.25 U-Shape 1.414 1 0.1768033 VSWR Calibration 2.0 U-Shape 1.414 1 1.4144272 Combined Standard Uncertainty 4.2363 Expanded Uncertainty (K=2) 8.4726 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 11 of 24 The total derived measurement uncertainty is +/- 8.47 dB. 9.3 RF conducted measurement The test is to measure the RF output power from the EUT. Some error sources that can contribute to the total uncertainty: - Uncertainty of the Reference Level Uncertainty - Uncertainty of variable attenuators - Uncertainty of cables - Uncertainty due to the mismatches Value Probability Division Sensitivity Expanded Source of Uncertainty (dB) Distribution Coefficient Uncertainty Reference Level 0.12 Rectangular 1.732 1 0.069284 Cable Insertion Loss 0.21 Normal 2 1 0.105 Attenuator 0.25 Normal 2 1 0.125 Mismatch 0.25 U-Shape 1.414 1 0.1768033 Combined Standard Uncertainty 0.476087 Expanded Uncertainty (K=2) 0.952174 The total derived measurement uncertainty is +/- 0.95 dB. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 12 of 24 10 Measurements, examination and derived results 10.1 Antenna Requirement Spec Requirement Applicable An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna requirement must meet at least one of the following: §15.203 ☒ a) Antenna must be permanently attached to the device. b) The antenna must use a unique type of connector to attach to the device. c) Device must be professionally installed. The installer shall be responsible for ensuring that the correct antenna is employed by the device. The Bluetooth Module uses a Chip antenna that is permanently attached to the board which meets the Remark requirement. Result ☒ PASS ☐ FAIL 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 13 of 24 11 Measurements, examination and derived results 11.1 Conducted emissions Spec Requirement Except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table, as measured using a 50 μH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. FCC 15.207 RSS GEN Limits for Conducted Emissions at the Mains Ports: Frequency ranges Limit (dBuV) Section (MHz) QP Average 0.15 ~ 0.5 66 – 56 56 – 46 15.209 0.5 ~ 5 56 46 5 ~ 30 60 50 Test Setup 1. The EUT and supporting equipment were set up in accordance with the requirements of the standard on top of a 1.5m x 1m x 0.8m high, non-metallic table. 2. 3. All other supporting equipment was powered separately from another main supply. Procedure 4. The EUT was switched on and allowed to warm up to its normal operating condition. 5. High peaks, relative to the limit line, were then selected from to the EMI test receiver. 6. The EMI test receiver was then tuned to the selected frequencies and the necessary measurements made with a receiver bandwidth setting of 10 kHz. All possible modes of operation were investigated. Only the 6 worst case emissions were measured and reported. All other emissions were relatively insignificant. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 14 of 24 Conducted Emission Test Results Test specification: Conducted Emissions Temp(°C): 23 Environmental Conditions: Humidity (%): 47 Atmospheric(mbar): 1018 Result: PASS Mains Power: 120V 60Hz Tested by: John Plotner Test Date: 1/28/19 Remarks: Ethernet Configuration, 60 Watt Adapter Line Frequency Raw Cable Loss Factors Level Measurement Line/ Limit Margin Pass (MHz) (dBuV) (dB) (dB) (dBuV) Type Neutral (dBuV) (dB) /Fail 1.490297 36.53 7.8 0.06 44.39 Quasi Peak Line 56 -11.61 Pass 29.23513 17.7 9.05 0.6 27.35 Quasi Peak Line 60 -32.65 Pass 24.39769 4.8 9.01 0.53 14.34 Quasi Peak Line 60 -45.66 Pass 22.53016 13.89 9 0.5 23.4 Quasi Peak Line 60 -36.6 Pass 29.37412 13.21 9.05 0.6 22.86 Quasi Peak Line 60 -37.14 Pass 23.22221 15.71 9 0.52 25.22 Quasi Peak Line 60 -34.78 Pass 1.490297 17.06 7.8 0.06 24.92 Average Line 46 -21.08 Pass 29.23513 15.92 9.05 0.6 25.57 Average Line 50 -24.43 Pass 24.39769 6.69 9.01 0.53 16.23 Average Line 50 -33.77 Pass 22.53016 5.06 9 0.5 14.56 Average Line 50 -35.44 Pass 29.37412 5.05 9.05 0.6 14.7 Average Line 50 -35.3 Pass 23.22221 5.05 9 0.52 14.56 Average Line 50 -35.44 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 15 of 24 Test specification: Conducted Emissions Temp(°C): 23 Environmental Conditions: Humidity (%): 47 Atmospheric(mbar): 1018 Result: PASS Mains Power: 120V 60Hz Tested by: John Plotner Test Date: 1/28/2019 Remarks: Ethernet Configuration, 60 Watt Adapter Neutral Frequency Raw Cable Loss Factors Level Measurement Line/ Limit Margin Pass (MHz) (dBuV) (dB) (dB) (dBuV) Type Neutral (dBuV) (dB) /Fail 28.36099 14.56 9.05 0.81 24.42 Quasi Peak Neutral 60 -35.58 Pass 28.39208 13.46 9.05 0.81 23.32 Quasi Peak Neutral 60 -36.68 Pass 22.85627 13.62 9 0.57 23.2 Quasi Peak Neutral 60 -36.8 Pass 19.70968 22.15 8.93 0.43 31.51 Quasi Peak Neutral 60 -28.49 Pass 28.22031 14.82 9.06 0.8 24.68 Quasi Peak Neutral 60 -35.32 Pass 28.28212 15.06 9.06 0.81 24.92 Quasi Peak Neutral 60 -35.08 Pass 28.36099 5.1 9.05 0.81 14.96 Average Neutral 50 -35.04 Pass 28.39208 5.1 9.05 0.81 14.96 Average Neutral 50 -35.04 Pass 22.85627 3.99 9 0.57 13.56 Average Neutral 50 -36.44 Pass 19.70968 19.53 8.93 0.43 28.89 Average Neutral 50 -21.11 Pass 28.22031 7.14 9.06 0.8 17 Average Neutral 50 -33 Pass 28.28212 5.84 9.06 0.81 15.7 Average Neutral 50 -34.3 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 16 of 24 11.2 Radiated Measurements 11.2.1 Radiated Measurements 30MHz to 1GHz Requirement(s): Spec Requirement Applicable Frequency range (MHz) Field Strength (uV/m) 30 – 88 100 47 CFR §15.209 88 – 216 150 ☒ RSS-247 216 960 200 Above 960 500 k Test Setup 1. The EUT was switched on and allowed to warm up to its normal operating condition. 2. The test was carried out at the selected frequency points obtained from the EUT characterisation. Maximization of the emissions, was carried out by rotating the EUT, changing the antenna polarization, and adjusting the antenna height in the following manner: a. Vertical or horizontal polarisation (whichever gave the higher emission level over a full Procedure rotation of the EUT) was chosen. b. The EUT was then rotated to the direction that gave the maximum emission. c. Finally, the antenna height was adjusted to the height that gave the maximum emission. 3. A Quasi-peak measurement was then made for that frequency point. 4. Steps 2 and 3 were repeated for the next frequency point, until all selected frequency points were measured. Temperature 20.1°C Test Date 02/01/2018 – 02/08/2018 Environmental conditions Relative Humidity 36% Atmospheric Pressure 1026mbar Remark - Result ☒ Pass ☐ Fail Test Data ☒ Yes (See below) ☐ N/A Test Plot ☒ Yes (See below) ☐ N/A Test was done by Deon Dai at 10-meter chamber. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 17 of 24 Test specification: Radiated Emissions Mains Power: 120VAC, 60Hz Tested by: Deon Dai ☒ Pass Result: ☐ Fail Test Date: 02/04/2018 Remarks: BLE, middle channel, worst case ƒ=30MHz – 1000MHz plot and 3-meter distance ƒ=30MHz – 1000MHz Measurements Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 449.97 41.19 14.06 -19.1 36.15 Quasi Max H 100 333 47 -10.85 Pass 975.00 19.29 16.02 -11.81 23.5 Quasi Max H 244 100 47 -23.5 Pass 30.51 18.01 11.12 -12.57 16.56 Quasi Max V 340 207 40 -23.45 Pass 199.99 30.69 12.62 -23.71 19.6 Quasi Max V 107 307 40 -20.4 Pass 105.24 18.8 11.92 -24.39 6.33 Quasi Max V 157 4 40 -33.67 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 18 of 24 11.2.2 Radiated Spurious Emissions between 1GHz-25GHz Requirement(s): Spec Item Requirement Applicable For non-restricted band, In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB or 30dB below that in the 100 ☒ a) kHz bandwidth within the band that contains the highest level of the 47CFR§15.247(d), desired power, determined by the measurement method on output power RSS 247 to be used. Attenuation below the general limits specified in § 15.209(a) is not required ☐ 20 dB down ☒ 30 dB down or restricted band, emission must also comply with the radiated emission b) ☐ limits specified in 15.209 Test Setup 1. The EUT was switched on and allowed to warm up to its normal operating condition. 2. The test was carried out at the selected frequency points obtained from the EUT characterisation. Maximization of the emissions, was carried out by rotating the EUT, changing the antenna polarization, and adjusting the antenna height in the following manner: a. Vertical or horizontal polarisation (whichever gave the higher emission level over a full Procedure rotation of the EUT) was chosen. b. The EUT was then rotated to the direction that gave the maximum emission. c. Finally, the antenna height was adjusted to the height that gave the maximum emission. 3. An average measurement was then made for that frequency point. 4. Steps 2 and 3 were repeated for the next frequency point, until all selected frequency points were measured. The EUT was scanned up to 40GHz. Both horizontal and vertical polarities were investigated. The results Remark show only the worst case. Result ☒ Pass Test Data ☒ Yes (See below) ☐ N/A Test Plot ☐ Yes (See below) ☒ N/A Test was done by Deon Dai at 10-meter chamber. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 19 of 24 BDR, low channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3587.52 46.98 3.58 -13.56 37 Peak Max H 213 296 74 -37 Pass 4804.74 49.16 4.1 -10.91 42.35 Peak Max H 224 26 74 -31.65 Pass 7818.33 49.48 5.28 -7.19 47.57 Peak Max H 161 150 74 -26.43 Pass 3587.52 32.44 3.58 -13.56 22.46 Average Max H 213 296 54 -31.54 Pass 4804.74 35.01 4.1 -10.91 28.2 Average Max V 224 26 54 -25.8 Pass 7818.33 35.24 5.28 -7.19 33.33 Average Max H 161 150 54 -20.67 Pass BDR, middle channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3656.00 47.91 3.57 -13.37 38.11 Peak Max H 205 294 74 -35.89 Pass 4881.97 48.24 4.18 -11.03 41.39 Peak Max V 215 25 74 -32.61 Pass 7557.32 49.91 5.15 -7.49 47.57 Peak Max V 163 152 74 -26.43 Pass 3656.00 33.87 3.57 -13.37 24.07 Average Max H 205 294 54 -29.93 Pass 4881.97 34.16 4.18 -11.03 27.31 Average Max H 215 25 54 -26.69 Pass 7557.32 35.23 5.15 -7.49 32.89 Average Max H 163 152 54 -21.11 Pass BDR, high channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3549.66 47.23 3.58 -13.67 37.14 Peak Max V 205 297 74 -36.86 Pass 4960.97 48.27 4.25 -11.16 41.36 Peak Max V 215 33 74 -32.64 Pass 7835.16 49.82 5.29 -7.18 47.93 Peak Max V 168 148 74 -26.07 Pass 3549.66 33.03 3.58 -13.67 22.94 Average Max H 205 297 54 -31.06 Pass 4960.97 33.52 4.25 -11.16 26.61 Average Max H 215 33 54 -27.39 Pass 7835.16 35.31 5.29 -7.18 33.42 Average Max H 168 148 54 -20.58 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 20 of 24 EDR, low channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3205.83 47.67 3.43 -13.78 37.32 Peak Max H 211 292 74 -36.68 Pass 4804.07 48.77 4.11 -10.91 41.97 Peak Max V 222 25 74 -32.03 Pass 7336.42 49.78 5.15 -7.65 47.28 Peak Max H 166 146 74 -26.72 Pass 3205.83 32.85 3.43 -13.78 22.5 Average Max H 211 292 54 -31.5 Pass 4804.07 34.39 4.11 -10.91 27.59 Average Max V 222 25 54 -26.41 Pass 7336.42 35.6 5.15 -7.65 33.1 Average Max H 166 146 54 -20.9 Pass EDR, middle channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3008.40 47.75 3.28 -14.16 36.87 Peak Max H 212 300 74 -37.13 Pass 4882.00 48.27 4.17 -11.03 41.41 Peak Max V 222 34 74 -32.59 Pass 7783.75 51.06 5.25 -7.22 49.09 Peak Max H 163 148 74 -24.91 Pass 3008.40 33.67 3.28 -14.16 22.79 Average Max V 212 300 54 -31.21 Pass 4882.00 33.8 4.17 -11.03 26.94 Average Max V 222 34 54 -27.06 Pass 7783.75 36.72 5.25 -7.22 34.75 Average Max H 163 148 54 -19.25 Pass EDR, high channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3044.81 47.31 3.31 -13.99 36.63 Peak Max H 206 296 74 -37.37 Pass 4960.31 48.21 4.25 -11.16 41.3 Peak Max V 216 34 74 -32.7 Pass 7776.92 50.12 5.24 -7.23 48.13 Peak Max H 162 147 74 -25.87 Pass 3044.81 32.68 3.31 -13.99 22 Average Max V 206 296 54 -32 Pass 4960.31 33.44 4.25 -11.16 26.53 Average Max V 216 34 54 -27.47 Pass 7776.92 35.95 5.24 -7.23 33.96 Average Max V 162 147 54 -20.04 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 21 of 24 BLE, low channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3456.60 54.34 3.56 -13.73 44.17 Peak Max H 213 300 74 -29.83 Pass 4804.62 56.17 4.1 -10.91 49.36 Peak Max V 219 32 74 -24.64 Pass 7880.97 57.79 5.33 -7.13 55.99 Peak Max V 163 151 74 -18.01 Pass 3456.60 49.08 3.56 -13.73 38.91 Average Max V 213 300 54 -15.09 Pass 4804.62 45.15 4.1 -10.91 38.34 Average Max V 219 32 54 -15.66 Pass 7880.97 46.59 5.33 -7.13 44.79 Average Max V 163 151 54 -9.21 Pass BLE, middle channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3088.95 54.34 3.34 -13.87 43.81 Peak Max H 209 296 74 -30.19 Pass 4881.59 55.24 4.18 -11.03 48.39 Peak Max H 220 32 74 -25.61 Pass 7194.26 56.4 5.14 -7.73 53.81 Peak Max H 170 145 74 -20.19 Pass 3088.95 48.1 3.34 -13.87 37.57 Average Max H 209 296 54 -16.43 Pass 4881.59 44.24 4.18 -11.03 37.39 Average Max V 220 32 54 -16.61 Pass 7194.26 44.49 5.14 -7.73 41.9 Average Max V 170 145 54 -12.1 Pass BLE, high channel: Frequency Raw Cable AF Level Measurement Hgt Azt Limit Margin Pass Pol MHz dBµV/m Loss dB dBµV/m Type cm Deg dBµV/m dB /Fail 3277.98 54.98 3.48 -13.75 44.71 Peak Max V 204 300 74 -29.29 Pass 4960.04 55.18 4.25 -11.16 48.27 Peak Max H 219 34 74 -25.73 Pass 7087.30 56.8 5.11 -7.78 54.13 Peak Max H 169 151 74 -19.87 Pass 3277.98 48.92 3.48 -13.75 38.65 Average Max H 204 300 54 -15.35 Pass 4960.04 43.43 4.25 -11.16 36.52 Average Max V 219 34 54 -17.48 Pass 7087.30 45.76 5.11 -7.78 43.09 Average Max H 169 151 54 -10.91 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 22 of 24 Annex A. TEST INSTRUMENT Instrument Model Serial # Cal Date Cal Cycle Cal Due In use Radiated Emissions Spectrum Analyzer N9030B 10SL0289 09/06/2018 1 Year 09/06/2019 Bi-Log antenna (30MHz~2GHz) JB1 A030702 07/13/2018 1 Year 07/13/2019 Horn Antenna (1-26.5GHz) 3115 10SL0059 11/09/2018 1 Year 11/09/2019 AC Line Conducted Instrument Model Serial # Cal Due In use EMI Test Receiver ESIB 40 100179 8/28/2019 YES Transient Limiter (9 kHz - 100 MHz) EM-7600-5 106 12/31/2019 YES LISN 3816/2NM 214372 1/10/2020 YES 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 23 of 24 Annex A. SIEMIC Accreditation Accreditations Document Scope / Remark ISO 17025 (A2LA) Please see the documents for the detailed scope ISO Guide 65 (A2LA) Please see the documents for the detailed scope TCB Designation A1, A2, A3, A4, B1, B2, B3, B4, C FCC DoC Accreditation FCC Declaration of Conformity Accreditation FCC Site Registration 3 meter site FCC Site Registration 10 meter site IC Site Registration 3 meter site IC Site Registration 10 meter site Radio Equipment: EN45011: EN ISO/IEC 17065 EU NB Electromagnetic Compatibility: EN45011 – EN ISO/IEC 17065 Singapore iDA Phase I, Phase II CB(Certification Body) Vietnam MIC Please see the document for the detailed scope CAB Accreditation (Phase II) OFCA Foreign Certification Body for Radio and Telecom Hong Kong OFCA (Phase I) Conformity Assessment Body for Radio and Telecom Radio: Scope A – All Radio Standard Specification in Category I Industry Canada CAB Telecom: CS-03 Part I, II, V, VI, VII, VIII 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL19011002-ZBR-101A2-BT Rev 1.0 Page 24 of 24 Radio: A1. Terminal equipment for purpose of calling Japan Recognized Certification Telecom: B1. Specified radio equipment specified in Article 38-2, Paragraph 1, Item Body Designation 1 of the Radio Law EMI: KCC Notice 2008-39, RRL Notice 2008-3: CA Procedures for EMI KN22: Test Method for EMI EMS: KCC Notice 2008-38, RRL Notice 2008-4: CA Procedures for EMS KN24, KN61000-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11: Test Method for EMS Korea CAB Accreditation Radio: RRL Notice 2008-26, RRL Notice 2008-2, RRL Notice 2008-10, RRL Notice 2007-49, RRL Notice 2007-20, RRL Notice 2007-21, RRL Notice 2007- 80, RRL Notice 2004-68 Telecom: President Notice 20664, RRL Notice 2007-30, RRL Notice 2008-7 with attachments 1, 3, 5, 6; President Notice 20664, RRL Notice 2008-7 with attachment 4 LP0002, PSTN01, ADSL01, ID0002, IS6100, CNS14336, PLMN07, PLMN01, Taiwan NCC CAB Recognition PLMN08 Taiwan BSMI CAB Recognition CNS 13438 R-3083: Radiation 3 meter site Japan VCCI C-3421: Main Ports Conducted Interference Measurement T-1597: Telecommunication Ports Conducted Interference Measurement EMC: AS/NZS CISPR 11, AS/NZS CISPR 14.1, AS/NZS CISPR22, AS/NZS 61000.6.3, AS/NZS 61000.6.4 Radiocommunications: AS/NZS 4281, AS/NZS 4268, AS/NZS 4280.1, AS/NZS 4280.2, AS/NZS 4295, AS/NZS 4582, AS/NZS 4583, AS/NZS 4769.1, Australia CAB Recognition AS/NZS 4769.2, AS/NZS 4770, AS/NZS 4771 Telecommunications: AS/ACIF S002:05, AS/ACIF S003:06, AS/ACIF S004:06 AS/ACIF S006:01, AS/ACIF S016:01, AS/ACIF S031:01, AS/ACIF S038:01, AS/ACIF S040:01, AS/ACIF S041:05, AS/ACIF S043.2:06, AS/ACIF S60950.1 AS/ACIF S002, AS/ACIF S003, AS/ACIF S004, AS/ACIF S006, AS/ACIF Australia NATA Recognition S016,AS/ACIF S031, AS/ACIF S038, AS/ACIF S040, AS/ACIF S041, AS/ACIF S043.2 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:


Document Created: 2019-04-05 22:54:26
Document Modified: 2019-04-05 22:54:26
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC