User manual

FCC ID: HYRDBRS201

Users Manual

Download: PDF

FCCID_393456

SPECIFICATIONS

Dual Beam
MOUNTING
MOUNTING HEIGHT RANGE:
18 inches to 36 inches

MOUNTING ANGLE:
0 degrees (Face of sensor parallel to level ground)

CONNECTOR PIN ASSIGNMENTS:
Pin A - 10-16 VDC
Pin B - No Connection
Pin C - Signal Output
Pin D - Ground Return
Replacement connector
P/N 1000-3160
18-36 inches

Radar Sensor
CABLE LENGTH ATTACHED TO THE RADAR SENSOR:
6 inches

ELECTRICAL
DC POWER REQUIREMENTS ..................... 10-16 DC
MICROWAVE FREQUENCY ......................... 24.125 GHz
OUTPUT CIRCUITRY CHARACTERISTICS ....... The output drive circuitry is current limited
and short circuit protected.
OUTPUT SIGNAL CHARACTERISTICS ........... The output signal, via output drive circuitry
Operator’s
provides a frequency type signal with
frequency proportional to target speed.
OUTPUT FREQUENCY .............................. Output is measured in Hz per miles per hour.
Manual
The frequency with the unit mounted at 0o
angle is:

57.42 Hz/MPH

ENVIRONMENTAL
VELOCITY: Typical
MINIMUM MAXIMUM
.4mph 65.0 mph
.6 kph 104.0 kph
OPERATING TEMPERATURE RANGE:
-30O Celsius to +70O Celsius
PHYSICAL DATA:
Size: 5.5 inches (14 cm) wide X 4.75inches
(12 cm) tall X 5.25 inches (13 cm) Deep

DBRS 201
Weight: 1.94 lbs. (880 grams)

Agri-Tronix Corporation • 2001 North Morton Street • Franklin, IN • 46131

MOUNTING THE RADAR SENSOR CHANGING DIRECTION OF TRAVEL

Steps for mounting your Radar Sensor are given below. The radar sensor bracket is designed so the radar sensor can be
mounted in two different configurations.
A. Be sure the tractor is on a level surface while installing the Radar
Sensor. The sensor can be installed so that the bracket may be mounted to the
side of the vehicle or to the front (or rear) of the vehicle. Remove the
B. In selecting the proper position to mount your Radar Sensor, the cover plater screws and orient the sensor to match one of the pictures
following considerations should be made: below. The arrows indicate the direction of travel.

Tabs indicate direction of radar TRAVEL
1. For optimum performance, the Radar Sensor should be mounted on beams
the tractor in a location which is BETWEEN crop rows.

Side of vehicle

Front or rear
2. The ideal location for the Radar Sensor would be near the center of
the tractor; this protects the Sensor from mud and other flying debris.

TRAVEL
3. If this ideal location is not possible, select an alternate mounting
location for the Radar Sensor. The Sensor has been designed to func-
tion in a wide variety of locations on the tractor.
Use this configuration Use this configuration
C. When installing the Radar Sensor, follow these rules: when mounting to the side when mounting to the
of a vehicle. front or rear of a vehicle.

1. The Radar Sensor must have an unobstructed view of the ground.
(Top view of bracket with radar sensor installed)

2. The Radar Sensor must be at a height of approximately 18-36
inches from the center of the gun to the ground. Warranty
This System is under warranty against defects in material or
3. The Radar Sensor face must be mounted so the face of the gun is
workmanship for a period of 1 year from the date of retail sale.
parallel to level ground.
Defective monitors must be returned to the place of purchase within the warranty period.
4. Align the top of the Sensor Mount, level with the ground by using a Components will be replaced or repaired at factory discretion. This warranty applies only to
bubble level. This will insure that the Radar Sensor is at the proper those systems which have been installed in accordance with published instructions.
position for optimum operation. This warranty is in lieu of all warranties, expressed or implied, and the manufacturer
expressly disclaims all other warranties, including without limitations any implied warranties of
merchantability and fitness for a particular purpose.

The manufacturer liability under this warranty shall not exceed the cost of the product.
Under no circumstance shall the manufacturer be responsible for equipment on which it’s monitors
are installed, field service calls relating to this equipment or for indirect, consequential or
special damages.
Level face of sensor with ground

Document Created: 2003-08-11 12:40:22
Document Modified: 2003-08-11 12:40:22

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC