Test report

FCC ID: HV4CTE660

Test Report

Download: PDF
FCCID_1366165

@ ZACTA Report number: Z071C—10292 Page 1 of 25 Report number: Z071C—10292 Issue Date: October 20, 2010 The device, as described herewith, was tested pursuant to applicable test procedure indicated below and complies with the requirements of; ECC Part15 Subpart C / IC RSS—210 The test results are traceable to the international or national standards. Applicant : Wacom Co., Ltd. " Equipment under test (EUT) : Pen Tablet FCC ID : HV4CTE660 Model Number : CTE—460/CTE—660 _ E Serial Number : OIFY$00070 / OIFY$00032 EUT Condition : Pre—production : Test procedure : ANSI C63.4—2003 Date of test : September 21, 28, 2010 Test place : 3m Semi—anechoic chamber, OATS Test results : Complied Zacta Technology Corporation certifies that no party to the application is subject to a denial of federal benefits that include FCC benefits, pursuant to Section 5301 ofthe Anti—Drug Abuse Act of 1988,21U.S8.C. 853(a). The results in this report are applicable only to the samples tested. This report shall not be re—produced except in full without the written approval of ZACTA Technology Corporation. This test report must not be used by client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Tested by: Ade/W/c\ Pntuatizs Tuhstes Hiroaki Suzuld‘ Mitsuhiro Takeda Authorized by: M/’L/ \_Sér/u// Jun Shimanuki IN V General Manager of Technical Division NVLAP LAB CODE 200306—0 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 2 of 25 Table of contents Page 1. Summary of Test.................................................................................................................................................................. 4 1.1 Purpose of test..........................................................................................................................................................................4 1.2 Standards..................................................................................................................................................................................4 1.3 Summary of test results ...........................................................................................................................................................4 1.4 Deviation from the standard....................................................................................................................................................4 1.5 Modification to the EUT by laboratory ..................................................................................................................................4 2. Equipment description......................................................................................................................................................... 5 2.1 General Description of equipment..........................................................................................................................................5 2.2 EUT information......................................................................................................................................................................5 2.3 Operating mode .......................................................................................................................................................................5 3. Configuration information................................................................................................................................................... 6 3.1 EUT and Peripheral(s) used ....................................................................................................................................................6 3.2 Cable(s) information................................................................................................................................................................6 3.3 System configuration...............................................................................................................................................................7 4. Test Type and Results .......................................................................................................................................................... 9 4.1 99% Occupied Bandwidth ......................................................................................................................................................9 4.1.1 Test Procedure [ IC RSS-210 A8.1(a) ]..........................................................................................................................9 4.1.2 Measurement Setup ...........................................................................................................................................................9 4.1.3 Limit of Bandwidth at 99% Occupied Bandwidth ...........................................................................................................9 4.1.4 Measurement Result........................................................................................................................................................10 4.1.5 Trace Data........................................................................................................................................................................11 4.2 Radiated Emissions (9kHz to 30MHz)................................................................................................................................ 12 4.2.1 Test Procedure [ FCC 15.209, IC RSS-210 2.2, RSS-Gen 4.9, 4.10, 4.11 ]................................................................12 4.2.2 Measurement Setup .........................................................................................................................................................12 4.2.3 Limit of Spurious Emission Measurement .....................................................................................................................13 4.2.4 Calculation Method .........................................................................................................................................................13 4.2.5 Measurement Results ......................................................................................................................................................13 4.3 Radiated Emissions (30MHz to 1000MHz)........................................................................................................................ 15 4.3.1 Test Procedure [ FCC 15.209, IC RSS-210 2.2, RSS-Gen 4.9, 4.10, 4.11 ]................................................................15 4.3.2 Measurement Setup .........................................................................................................................................................15 4.3.3 Limit of Spurious Emission Measurement .....................................................................................................................16 4.3.4 Calculation Method .........................................................................................................................................................16 4.3.5 Measurement Results ......................................................................................................................................................17 4.4 AC power line Conducted Emissions.................................................................................................................................. 19 4.4.1 Test Procedure [ FCC 15.207, IC RSS-Gen 7.2.2 ] .....................................................................................................19 4.4.2 Measurement Setup .........................................................................................................................................................19 4.4.3 Limit of AC power line Conducted Emissions Measurement ........................................................................................20 4.4.4 Calculation method..........................................................................................................................................................20 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 3 of 25 4.4.5 Measurement Result........................................................................................................................................................21 5. Uncertainty of measurement ............................................................................................................................................. 23 6. Laboratory description....................................................................................................................................................... 24 6.1 Location: ............................................................................................................................................................................... 24 6.2 Facility filing information: ................................................................................................................................................... 24 Appendix A: Test equipment................................................................................................................................................. 25 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 4 of 25 1. Summary of Test 1.1 Purpose of test It is the original test in order to verify conformance to standards listed in section 1.2. 1.2 Standards CFR47 FCC Part 15 Subpart C, RSS-210 1.3 Summary of test results Test Items Test Items Condition Result Section Transmit mode [Tx]: RSS-Gen 4.6.1 99% Occupied Bandwidth Radiated Pass 15.209 RSS-210 2.2 Radiated Emissions Radiated Pass RSS-Gen 4.9, 4.10, 4.11 15.207 AC Power Line Conducted Conducted Pass RSS-Gen 7.2.2 Emissions 150kHz – 30MHz 1.4 Deviation from the standard None 1.5 Modification to the EUT by laboratory None ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 5 of 25 2. Equipment description 2.1 General Description of equipment The EUT is a Pen Tablet, which is transceiver. 2.2 EUT information Applicant : Wacom Co., Ltd. 2-510-1, Toyonodai, Kazo-shi, Saitama 349-1148, Japan Phone: + 81-480-78-1257 Fax: + 81-480-78-1404 Equipment under test (EUT) : Pen Tablet Trade name : WACOM Model number : CTE-460 CTE-660 Serial number : 0IFYS00070 (CTE-460) 0IFYS00032 (CTE-660) EUT condition : Pre-production Max. frequency : 12MHz Power ratings : DC 5V (USB) Size : (W) 213.30 x (D) 188.46 x (H) 10.2 mm (CTE-460) (W) 285.29 x (D) 231.46 x (H) 10.2 mm (CTE-660) Environment : Indoor use Thermal limitation : 5ºC to 35ºC Operating mode : Normal Operation Variation of the family model(s) : CTE-460 - Size: (W) 213.30 x (D) 188.46 x (H) 10.2mm (Pen Active Area: (W) 147.6 x (D) 92.25 mm) CTE-660 - Size: (W) 285.29 x (D) 231.46 x (H) 10.2mm (Pen Active Area: (W) 216.48 x (D) 135.3 mm) [RF Specification] Frequency Range : 750.0kHz Modulation method : OOK (On-Off-Keying) RF emission type designator : 80K4K1D (CTE-460) 80K3K1D (CTE-660) 2.3 Operating mode 【Normal Operation】 i) Tablet test set up ii) Select a Packet measurement iii) Start test mode ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 6 of 25 3. Configuration information 3.1 EUT and Peripheral(s) used No. Equipment Company Model No. Serial No. FCC ID/DoC Comment CTE-460 0IFYS00070 1 Pen Tablet Wacom FCC ID: HV4CTE660 EUT CTE-660 0IFYS00032 EP-150-1K N/A - Accessory*1 2 Pen Wacom EP-150-0K N/A - Accessory*2 3 Personal Computer DELL DCM 1HZY31X DoC - CN-07N247-38 4 Keyboard DELL SK-8110 DoC - 844-293-0337 5 PS/2 Mouse DELL M-SAW34 LZB23459449 DZL211029 - CN-0540NK-47 Below E771p A3KM076 803-1BC-CRDF 30MHz 6 Display DELL CN-0MC42-641 Above E176FPc DoC 80-657-0V0K 30MHz 7 Printer HP C4555A SG69A1425N B94C4555X - Sport_Ster33.6 000839032BK 8 Modem US. Robotics DoC - Kbps 6YV4J 9 AC adapter for Modem US. Robotics N/A N/A - - *1: Accessory for CTE-460. *2: Accessory for CTE-660. 3.2 Cable(s) information No. Cable Length [m] Shield Connector Comment a USB cable 1.5 Yes Metal Accessory b Keyboard cable 2.1 No Metal - c Mouse cable 1.8 No Metal - 1.8 Yes Metal Below 30MHz d RGB cable 1.5 Yes Metal Above 30MHz 1.9 No Plastic Below 30MHz e AC cable 1.8 No Plastic Above 30MHz f Parallel cable 2.1 Yes Metal - g AC cable 2.6 No Plastic - h Serial cable 3.0 Yes Metal - i DC cable 1.8 No Plastic - j AC cable 1.6 No Plastic - ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 7 of 25 3.3 System configuration Below 30MHz 3. Personal Computer 1. Pen Tablet (EUT) a. # USB USB 2. Pen b. # 4. Keyboard PS/2 c. # 5. PS/2 Mouse PS/2 d.* # 6. Display e. AC 120V RGB 60Hz f. * 7. Printer g. AC 120V Parallel 60Hz h. * 8. Modem i. # 9. AC adapter AC 120V Serial 60Hz j. AC 120V AC in 60Hz # : Un-detachable cable : Ferrite core * : Bundled excess cable Note1: Numbers assigned to equipment or cables on this diagram are corresponded to the list in “3.1 EUT and Peripheral(s) used” and “3.2 Cable(s) information”. Note2: RGB cable(No.d) with one ferrite core is accessory for Display(No.6). ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 8 of 25 Above 30MHz 3. Personal Computer 1. Pen Tablet (EUT) # a. USB USB 2. Pen b. # 4. Keyboard PS/2 c. # 5. PS/2 Mouse PS/2 d.* 6. Display e. AC 120V RGB 60Hz f. * 7. Printer g. AC 120V Parallel 60Hz h. * 8. Modem i. # 9. AC adapter AC 120V Serial 60Hz j. AC 120V AC in 60Hz # : Un-detachable cable : Ferrite core * : Bundled excess cable Note1: Numbers assigned to equipment or cables on this diagram are corresponded to the list in “3.1 EUT and Peripheral(s) used” and “3.2 Cable(s) information”. Note2: RGB cable(No.d) with two ferrite cores is accessory for Display(No.6). ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 9 of 25 4. Test Type and Results 4.1 99% Occupied Bandwidth 4.1.1 Test Procedure [ IC RSS-210 A8.1(a) ] The transmitter output is connected to the spectrum analyzer. The RBW is set to 1% to 3% of the 99% bandwidth. The VBW is set to 3 times the RBW. The sweep time is coupled. The spectrum analyzer internal 99% bandwidth function is utilized. The spectrum analyzer is set to: - RBW=3kHz, VBW=10kHz, Span=300kHz, Sweep=auto The test mode of EUT is as follows. - Normal Operation 4.1.2 Measurement Setup Test configuration for 99% Occupied Bandwidth Test room Measurement room Loop Spectrum analyzer / Receiver Preamplifier Antenna Cable system 4.1.3 Limit of Bandwidth at 99% Occupied Bandwidth None ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 10 of 25 4.1.4 Measurement Result [CTE-460] Frequency Occupied Bandwidth [MHz] [kHz] 0.750 80.4096 [CTE-660] Frequency Occupied Bandwidth [MHz] [kHz] 0.750 80.2760 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 11 of 25 4.1.5 Trace Data Test Personnel: Date : Sep. 28, 2010 Temperature : 24.1 [ºC] Tested by: Hiroaki Suzuki Humidity : 56.3 [%] Test place : 3m Semi-anechoic chamber [CTE-460] [CTE-660] ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 12 of 25 4.2 Radiated Emissions (9kHz to 30MHz) 4.2.1 Test Procedure [ FCC 15.209, IC RSS-210 2.2, RSS-Gen 4.9, 4.10, 4.11 ] Radiated emission measurements are performed at 3m distance with the Loop antenna. The antenna is positioned with its plane vertical, and the center of the Loop is 1.0meter above the ground plane. Frequency Range: 9kHz to 30MHz is scanned and investigated with the test receiver. The detector function of the test receiver is set to CISPR Quasi-peak mode and the bandwidth is set to 200Hz (9kHz to 150kHz) and 9kHz (150kHz to 30MHz). The EUT and support equipment are placed on a 1 meter x 2.0 meter surface, 0.8 meter height FRP table. The turntable and the loop antenna are rotated by 360 degrees and stopped at azimuth of producing the maximum emission. Interconnecting cables, which hanging closer than 40cm to the horizontal metal ground plane are bundled its excess in center. The test results represent the worst-case emission for each emission with manipulating the EUT, support equipment, interconnecting cables and varying the mode of operation. Sufficient time for the EUT, support equipment, and test equipment are allowed in order for them to warm up to their normal operating condition. Frequency range: - 9kHz to 30MHz The Test receiver is set to: Detector: Quasi-peak Bandwidth: 200Hz, 9kHz The test mode of EUT is as follows. - Normal Operation 4.2.2 Measurement Setup Test configuration for Radiated emissions Test room Measurement room Antenna Preamplifier Spectrum analyzer / Receiver Cable system ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 13 of 25 4.2.3 Limit of Spurious Emission Measurement Frequency Field Strength Distance [MHz] [uV/m] [dBuV/m] [m] 0.009 – 0.490 2400 / F [kHz] 20logE [uV/m] 300 0.490 – 1.705 24000 / F [kHz] 20logE [uV/m] 30 1.705-30 30 29.5 30 30 – 88 100 40.0 3 88 – 216 150 43.5 3 216 – 960 200 46.0 3 Above 960 500 54.0 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level [dBuV/m] = 20 log Emission [uV/m] 3. Measurements were corrected to 30m using 40log (3/30) = -40.0dB 4.2.4 Calculation Method Emission level = Reading + c.f (Ant. factor + Cable system loss – Amp. Gain) Margin = Limit – Emission level 4.2.5 Measurement Results Test Personnel: Date : Sep. 28, 2010 Temperature : 24.1 [ºC] Tested by: Hiroaki Suzuki Humidity : 56.3 [%] Test place : 3m Semi-anechoic chamber [CTE-460] Frequency Reading Result Result Limit c.f Margin [dBuV] [dBuV/m] [dBuV/m] [dBuV/m] Result [MHz] [dB(1/m)] [dB] at 3m at 3m at 30m at 30m 0.750 54.3 -10.3 44.0 4.0 30.1 26.1 PASS 1.502 33.6 -10.2 23.4 -16.6 24.1 40.7 PASS 2.251 42.4 -10.1 32.3 -7.7 29.5 37.2 PASS 3.004 33.4 -10.0 23.4 -16.6 29.5 46.1 PASS ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 14 of 25 [CTE-660] Frequency Reading Result Result Limit c.f Margin [dBuV] [dBuV/m] [dBuV/m] [dBuV/m] Result [MHz] [dB(1/m)] [dB] at 3m at 3m at 30m at 30m 0.750 50.0 -10.3 39.7 -0.3 30.1 30.4 PASS 1.502 33.7 -10.2 23.5 -16.5 24.1 40.6 PASS 2.253 36.6 -10.1 26.5 -13.5 29.5 43.0 PASS 3.004 33.4 -10.0 23.4 -16.6 29.5 46.1 PASS ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 15 of 25 4.3 Radiated Emissions (30MHz to 1000MHz) 4.3.1 Test Procedure [ FCC 15.209, IC RSS-210 2.2, RSS-Gen 4.9, 4.10, 4.11 ] Radiated emission measurements are performed at 10m distance with the Biconical antenna and Log periodic antenna. The antenna is positioned both the horizontal and vertical planes of polarization and height is varied 1 to 4 meters and stopped at height producing the maximum emission. Frequency Range: 30MHz to 1000MHz is scanned and investigated with the test receiver. The detector function of the test receiver is set to CISPR Quasi-peak mode and the bandwidth is set to 120kHz. The EUT and support equipment are placed on a 1 meter x 2.0 meter surface, 0.8 meter height wooden table. The turntable and the loop antenna are rotated by 360 degrees and stopped at azimuth of producing the maximum emission. Interconnecting cables, which hanging closer than 40cm to the horizontal metal ground plane are bundled its excess in center. The test results represent the worst-case emission for each emission with manipulating the EUT, support equipment, interconnecting cables and varying the mode of operation. Sufficient time for the EUT, support equipment, and test equipment are allowed in order for them to warm up to their normal operating condition. Frequency range: - 30MHz to 1000MHz The Test receiver is set to: Detector: Quasi-peak Bandwidth: 120kHz The test mode of EUT is as follows. - Normal Operation 4.3.2 Measurement Setup Test configuration for Radiated emissions Test room Measurement room Antenna Preamplifier Spectrum analyzer / Receiver Cable system ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 16 of 25 4.3.3 Limit of Spurious Emission Measurement Frequency Limit Distance [MHz] [dBuV/m] [m] 30 – 300 30 10 300 – 1000 37 10 NOTE: 1. CISPR 22 limit was applied to Radiated emission measurements as prescribed in FCC part 15 section 15.109(g). 2. Emission level [dBuV/m] = 20 log Emission [uV/m] 4.3.4 Calculation Method Emission level = Reading + c.f (Ant. factor + Cable system loss – Amp. Gain) Margin = Limit – Emission level ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 17 of 25 4.3.5 Measurement Results [CTE-460] ***** RADIATED EMISSION ***** Sheet number : 1 Standard : FCC Part 15 Subpart B (CISPR 22) 60 Emission Level [dBµV/m] Class :B Distance [m] : 10 HOR Date of test : 2010/9/21 50 Test site :3 VER Temperature [℃] : 28.2 40 Humidity [%] : 48.4 Operator : M.Takeda Company name : Wacom Co., Ltd. 30 EUT : Pen Tablet Model number : CTE-460 20 Serial number : 0IFYS00070 Test mode : Normal Operation Comment : 10 30M 50M 100M 300M 500M 1G Frequency [Hz] Antenna Table Reading Factor Emission Limit Margin Pol. Height Radian Frequency Level Level Comment HOR/VER [m] [Deg.] [MHz] [dBµV] [dB/m] [dBµV/m] [dBµV/m] [dB] VER 1.0 275 48.03 35.5 -14.7 20.8 30.0 9.2 HOR 4.0 335 96.01 36.0 -16.4 19.6 30.0 10.4 VER 1.0 205 96.04 41.2 -16.4 24.8 30.0 5.2 * HOR 4.0 130 108.03 31.5 -14.2 17.3 30.0 12.7 HOR 4.0 350 144.01 30.3 -10.6 19.7 30.0 10.3 VER 1.0 210 144.01 30.7 -10.6 20.1 30.0 9.9 VER 1.0 145 168.12 27.1 -9.4 17.7 30.0 12.3 HOR 4.0 25 168.15 30.5 -9.4 21.1 30.0 8.9 VER 1.0 50 180.21 29.0 -8.9 20.1 30.0 9.9 HOR 4.0 10 180.23 32.3 -8.9 23.4 30.0 6.6 HOR 4.0 310 192.01 27.9 -8.4 19.5 30.0 10.5 VER 1.0 60 192.04 30.8 -8.4 22.4 30.0 7.6 HOR 4.0 320 216.31 26.7 -8.0 18.7 30.0 11.3 VER 1.0 20 240.05 32.1 -7.7 24.4 37.0 12.6 *：The worst emission. Factor：Antenna Factor + Attenuator + Cable Loss - Amp Gain Ver.2.81 F3#043 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 18 of 25 [CTE-660] ***** RADIATED EMISSION ***** Sheet number : 2 Standard : FCC Part 15 Subpart B (CISPR 22) 60 Emission Level [dBµV/m] Class :B Distance [m] : 10 HOR Date of test : 2010/9/21 50 Test site :3 VER Temperature [℃] : 28.2 40 Humidity [%] : 48.4 Operator : M.Takeda Company name : Wacom Co., Ltd. 30 EUT : Pen Tablet Model number : CTE-660 20 Serial number : 0IFYS00032 Test mode : Normal Operation Comment : 10 30M 50M 100M 300M 500M 1G Frequency [Hz] Antenna Table Reading Factor Emission Limit Margin Pol. Height Radian Frequency Level Level Comment HOR/VER [m] [Deg.] [MHz] [dBµV] [dB/m] [dBµV/m] [dBµV/m] [dB] VER 1.0 110 48.03 35.5 -14.7 20.8 30.0 9.2 HOR 4.0 310 96.01 36.0 -16.4 19.6 30.0 10.4 VER 1.0 210 96.04 41.2 -16.4 24.8 30.0 5.2 HOR 4.0 125 108.03 34.6 -14.2 20.4 30.0 9.6 HOR 4.0 340 144.01 30.4 -10.6 19.8 30.0 10.2 VER 1.0 250 144.01 31.3 -10.6 20.7 30.0 9.3 VER 1.0 15 168.12 27.2 -9.4 17.8 30.0 12.2 HOR 4.0 350 168.22 30.2 -9.4 20.8 30.0 9.2 HOR 4.0 5 180.13 34.1 -8.9 25.2 30.0 4.8 * HOR 4.0 20 192.13 31.5 -8.4 23.1 30.0 6.9 HOR 4.0 330 216.08 28.9 -8.0 20.9 30.0 9.1 VER 1.0 5 216.11 28.0 -8.0 20.0 30.0 10.0 VER 1.0 190 240.05 31.5 -7.7 23.8 37.0 13.2 *：The worst emission. Factor：Antenna Factor + Attenuator + Cable Loss - Amp Gain Ver.2.81 F3#043 ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 19 of 25 4.4 AC power line Conducted Emissions 4.4.1 Test Procedure [ FCC 15.207, IC RSS-Gen 7.2.2 ] Conducted emission at AC mains port measurements are performed at open area test site according to ANSI C63.4 section 7. EUT and support equipment are placed on wooden table of 2.0m(W) × 1.0m(D) × 0.8m(H) in size. EUT is connected to 50Ω/50µH Line impedance stabilization network (LISN) which is placed on reference ground plane, and was placed 80cm away from EUT. Excess of AC power cable is bundled in center. Vertical Metal Reference Plane 2.0m (W) × 2.0m (H) in size is placed 0.4m away from EUT. LISN for peripheral is terminated in 50Ω. EUT operating mode is selected to emit the maximum noise. Overall frequency range is investigated with spectrum analyzer using peak detector. Maximum emission configuration is determined by manipulating the EUT, support equipment, interconnecting cables. Then, emission measurements are performed with test receiver in above setting to each current-carrying conductor of the mains port. Sufficient time for EUT, support equipment and test equipment are provided in order for them to warm up to their normal operating condition. Frequency range: - 0.15MHz to 30MHz The Test receiver is set to: Detector: Quasi-peak, Average Bandwidth: 9kHz The test mode of EUT is as follows. - Normal Operation 4.4.2 Measurement Setup Test configuration for AC power line Conducted Emissions Test room Measurement room Vertical metal reference plane*1 LISN Spectrum analyzer / Receiver Cable system *1: Used it for Table-top only ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 20 of 25 4.4.3 Limit of AC power line Conducted Emissions Measurement Limit Frequency QP(dBµV) AV(dBµV) 0.15MHz to 0.5MHz 66 to 56* 56 to 46* 0.5MHz to 5MHz 56 46 5MHz to 30MHz 60 50 *: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 4.4.4 Calculation method Emission level = Reading + (LISN. factor + Cable system loss) Margin = Limit – Emission level ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 21 of 25 4.4.5 Measurement Result [CTE-460] ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 22 of 25 [CTE-660] ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 23 of 25 5. Uncertainty of measurement Expanded uncertainties stated were calculated with a coverage Factor k= 2. Please note that these results are not taken into account when determining compliance or non-compliance with test result. Test item Measurement uncertainty Conducted emission at mains port (150kHz - 30MHz) ±3.0dB Radiated emission (9kHz - 30MHz) ±4.4dB Radiated emission (30MHz – 1000MHz) ±4.5dB Radiated emission (1000MHz – 26GHz) ±3.9dB ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 24 of 25 6. Laboratory description 6.1 Location: ZACTA Technology Corporation Yonezawa Testing Center 4149-7 Hachimanpara 5-chome Yonezawa-shi Yamagata 992-1128 Japan Phone: +81-238-28-2880 Fax: +81-238-28-2888 6.2 Facility filing information: 1) NVLAP accreditation: NVLAP Lab. code: 200306-0 2) FCC filing: Site name Registration Number Expiry Date Site 2, Site3 91065 November 19, 2011 3m Semi-anechoic chamber 540072 February 16, 2013 10m Semi-anechoic chamber 3) Industry Canada Oats site filing: Sites on file: Site name Oats 3m/10m Expiry Date Site 2 4224A-2 February 16, 2012 Site 3 4224A-3 February 16, 2012 3m Semi-anechoic chamber 4224A-4 February 16, 2012 10m Semi-anechoic chamber 4224A-5 February 16, 2012 4) VCCI site filing: Conducted Conducted Radiated Emission Site name Expiry Date emission for Expiry Date emission for mains telecom port port Site 2 R-137 C-133 Nov. 16, 2011 T-1477 Oct. 8, 2011 Site 3 R-138 C-134 Nov. 16,2011 T-1478 Oct. 8, 2011 10m Semi-anechoic chamber R-2480 C-2722 Jul. 3, 2011 T-1474 Oct. 8, 2011 3m Semi-anechoic chamber R-2481 C-2723 Jul. 3, 2011 T-1475 Oct. 8, 2011 Shielded room No.1 R-137 C-2724 Jul. 3, 2011 T-1476 Oct. 8, 2011 5) ETL SEMKO authorization: Authorized as an EMC test laboratory. 6) TUV Rheinland authorization: Authorized as an EMC test laboratory. 7) BUREAU VERITAS certification: Certified as an EMC test laboratory. ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0

Report number: Z071C-10292 Page 25 of 25 Appendix A: Test equipment List of Measuring Instruments Equipment Company Model No. Serial No. Cal. due Cal. date EMI Receiver ROHDE&SCHWARZ ESCI 100451 May 2011 May 28, 2010 EMI Receiver ROHDE&SCHWARZ ESCI 100764 Jun. 2011 Jun. 14, 2010 Spectrum Analyzer Agilent Technologies E4447A MY46180188 Mar. 2011 Mar. 4, 2010 8656B 2634A03228 Spectrum Analyzer Agilent Technologies Dec. 2010 Dec. 8, 2009 85662A 2648A14093 Preamplifier ANRITSU MH648A M08067 Jun. 2011 Jun. 12, 2010 Preamplifier ANRITSU MH648A M96157 May 2011 May 28, 2010 Coaxial switch ANRITSU MP59B 6200611581 May 2011 May 28, 2010 Attenuator TYC BA-PJ-10 N/A (S348) Apr.. 2011 Apr. 26, 2010 Line impedance Kyoritsu Electrical stabilization network KNW-407 8-693-20 Mar. 2011 Mar. 12, 2010 for EUT Works, Ltd. Line impedance Kyoritsu Electrical stabilization network KNW-242C 8-1094-5 Mar. 2011 Mar. 12, 2010 for peripheral Works, Ltd. 50Ω terminator HRS UG-88/U N/A (S065) Mar. 2011 Mar. 5, 2010 Loop antenna ROHDE&SCHWARZ HFH2-Z2 892246/010 Feb.2011 Feb. 25, 2010 Biconical antenna Schwarzbeck VHA9103/BBA9106 2322 Jun. 2011 Jun. 12, 2010 Log Periodic antenna Schwarzbeck UHALP9108A 0398 Jun. 2011 Jun. 12, 2010 Attenuator TDC TAT-43B-03 N/A (S204) Jun. 2011 Jun. 12, 2010 Attenuator TDC TAT-43B-03 N/A (S206) Jun. 2011 Jun. 12, 2010 5D-2W/10m #AEC3R-001 Feb. 2011 Feb. 5, 2010 Fujikura 5D-2W/1.5m #AEC3R-003 Feb. 2011 Feb. 5, 2010 Coaxial cable 5D-2W/0.5m #AEC3R-004 Feb. 2011 Feb. 5, 2010 SUHNER SUCOFLEX_106/7m #AEC3R-002 Feb. 2011 Feb. 5, 2010 8D-SFA/15m OATS#3R-001 May 2011 May 28, 2010 8D-SFA/15m OATS#3R-002 May 2011 May 28, 2010 Coaxial cable Fujikura 8D-2W/8m OATS#3R-003 May 2011 May 28, 2010 5D-2W/1m OATS#3RC-001 May 2011 May 28, 2010 5D-2W/1m OATS#3RC-002 May 2011 May 28, 2010 Coaxial cable Fujikura 5D-2W/15m OATS#3C May 2011 May 28, 2010 PC DELL DIMENSION E521 75465BX N/A N/A PC IBM 6892-44J 97-43012 N/A N/A Software TOYO Corporation EP5/RE-AJ 0611193/V3.4 N/A N/A Software ZACTA EMI Data Sheet Ver.2.81 N/A N/A Software TOYO Corporation EP5/CE-AJ 0611193/V3.3 N/A N/A 3m Semi-anechoic chamber TOKIN N/A N/A (9002-NSA) May 2011 May 18, 2010 ZACTA Technology Normalized Site Attenuation N/A OATS#3 Jul. 2011 Jul. 3, 2010 Corp. *The calibrations of the above equipment are traceable to NIST or equivalent standards of the reference organizations. ZACTA Technology Corp. FCC ID: HV4CTE660 FCC 15C Rev.3.0


Document Created: 2010-10-21 11:46:13
Document Modified: 2010-10-21 11:46:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC