RF Exposure

FCC ID: HQXNCSP3DC

RF Exposure Info

Download: PDF

FCCID_3688724

FCC ID: HQXNCSP3DC

RF Exposure Evaluation
of
E.U.T. : NCSP3 Display Commander

FCC ID. : HQXNCSP3DC

MODEL : NCSP3DC

for

APPLICANT : Sysgration Ltd.

ADDRESS : 6F-2.,No.1,Sec.1,Tiding Blvd., Neihu Dist., Taipei
City 114, Taiwan

Prepared by

ELECTRONICS TESTING CENTER, TAIWAN
NO. 34. LIN 5. DINGFU, LINKOU DIST.,
NEW TAIPEI CITY, TAIWAN, 24442, R.O.C.
Tel:(02)26023052 Fax:(02)26010910
http://www.etc.org.tw ; e-mail: emc@etc.org.tw
Report Number : 17-09-RBF-019-MPE

FCC ID: HQXNCSP3DC

TEST REPORT CERTIFICATION
Applicant : Sysgration Ltd.
6F-2.,No.1,Sec.1,Tiding Blvd., Neihu Dist., Taipei City 114, Taiwan

Manufacturer : Sysgration Ltd.(Nan-Kang Factory)
No.28,North Industry Rd., Nan-Kang Industrial Zone, Nan-Tou
City, Nan-Tou County 540, Taiwan

Description of EUT

a) Type of EUT : NCSP3 Display Commander

b) Trade Name : iN‧Command

c) Model No. : NCSP3DC

d) Power Supply : DC 12V

Regulation Applied : FCC KDB447498 D01. The equipment fulfills the
requirements on power density for general population/uncontrolled exposure and
therefore fulfills the requirements of section 1.1310 of FCC 47 CFR Part 1.
Note: 1. The result of the testing report relate only to the item tested.
2. The testing report shall not be reproduced expect in full, without the written
approval of ETC

FCC ID: HQXNCSP3DC

Product Information:
Type of EUT: NCSP3 Display Commander
FCC ID: HQXNCSP3DC
Model: NCSP3DC
Description: The product contains 802.11b/g/n WiFi and Bluetooth.

Maximum conducted output power (rated):
802.11b/g/n WiFi 16 dBm or 39.811mW
Bluetooth (FHSS) 8 dBm or 6.310mW
Bluetooth (BLE) 8 dBm or 6.310mW

The following table lists the provided authorized antennas:
Model Antenna Type Antenna Gain
(dBi) Numeric
CL-1105-03-1R PCB Antenna 4.6 2.88

Below is an example of the RF Exposure Statement:

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements,
the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. No change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure requirements and void user’s authority to operate
the device.

FCC ID: HQXNCSP3DC

Relative Requirement for Compliance
According to section 1.1310 of FCC 47 CFR Part 1, limits for maximum permissible
exposure (MPE) are as following:

TABLE 1 – LIMITS FOR MAXIMUN PERMISSIBLE EXPOSURE (MPE)
Frequency Range Electric Field Magnetic Field Power Density Averaging Time
(MHz) Strength Strength
(V/m) (A/m) (mW/cm2) (minutes)
(A) Limits for Occupational/Controlled Exposures
0.3-3.0 ……………… 614 1.63 *(100) 6
3-30 ………………… 1842/f 4.89/f *(900/f2) 6
30-300 ……………… 61.4 0.163 1.0 6
300-1500 …………... …………………. …………………. f/300 6
1500-100,000 ……… …………………. …………………. 5 6
(B) Limits for General Population/Uncontrolled Exposure
0.3-1.34 …………… 614 1.63 *(100) 30
1.34-30 …………… 824/f 2.19/f *(180/f2) 30
30-300 ……………… 27.5 0.073 0.2 30
300-1500 …………... …………………. …………………. f/1500 30
1500-100,000 ……… …………………. …………………. 1.0 30
f = frequency in MHz
* = Plane-wave equivalent power density
NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a
consequence of their employment provided those persons are fully aware of the potential for exposure and can
exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when
an individual is transient through a location where occupational / controlled limits apply provided he or she is
made aware of the potential for exposure.
NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general
public may be exposed, or in which persons that are exposed as a consequence of their employment may not
be fully aware of the potential for exposure or can not exercise control over their exposure.

FCC ID: HQXNCSP3DC

RF Exposure Calculations:
The following information provides the minimum separation distance for the highest
gain antenna provided. This calculation is based on the highest EIRP possible from
the system, considering maximum power and antenna gain, and considering a 1.0
mW/cm2 uncontrolled exposure limit. The formula shown in OET Bulletin 65 is used in
the calculation.
Equation from page 19 of OET Bulletin 65, Edition 97-01 is:

S= PG / 4πR2
where: S = power density (in appropriate units, e.g. mW/cm2)
P = power input to the antenna (in appropriate units, e.g., mW)
G = power gain of the antenna in the direction of interest relative to
an isotropic radiator
R = distance to the center of radiation of the antenna (appropriate
units, e.g., cm)
hence

R= (PG / 4πS)1/2
For our device
(1) 802.11b/g/n WiFi
P = 39.811mW
G = 2.88
R = 20 cm
S = (39.811 * 2.88) / (4*π*202) = 0.0228 mW/cm2 < 1.0 mW/cm2

(2) Bluetooth
P = 6.310mW
G = 2.88
R = 20 cm
S = (6.310 * 2.88) / (4*π*202) = 0.0036 mW/cm2 < 1.0 mW/cm2

Total power density
S = 0.0228+0.0036 = 0.0264 mW/cm2 < 1.0 mW/cm2

FCC ID: HQXNCSP3DC

For complying the FCC limits for general population/uncontrolled exposure, the
power density limit is 1.0 mW/cm2. The calculation result of the power density at a
distance of 20 cm of our device is less than the limit.

Summary of Evaluation

Test Reference Results
Evaluation Section 1.1310 of FCC 47 CFR Part 1 Pass
FCC KDB447498 D01

Document Created: 2017-12-20 14:41:52
Document Modified: 2017-12-20 14:41:52

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC