Report

FCC ID: HQXAXM-Q6

Test Report

Download: PDF
FCCID_1802243

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 FCC 47 CFR PART 15 SUBPART C for Wireless Mini BlueScan Mouse Model: AXM-Q6 / 00033 Brand: Sysgration / TUMI Test Report Number: C120921Z04-RP1 Issued for Sysgration Ltd. 10FL, NO.868-3, Chung Rd, Chung Ho, Taipei, Taiwan, R.O.C. Issued by: COMPLIANCE CERTIFICATION SERVICES (SHENZHEN) INC. No.10-1, Mingkeda Logistics Park, No.18, Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China TEL: 86-755-28055000 FAX: 86-755-28055221 Issued Date: September 21, 2012 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NVLAP, NIST or any government agencies. The test result of this report relate only to the tested sample identified in this report. FCC ID: HQXAXM-Q6 Page 1/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Revision History Issue Effect Revised By Rev. No. Revisions Page 00 SZ120705B01-RP Initial Issue ALL Sunny Wang 01 C120921Z04-RP1 Update ALL Sunny Wang Rev.01: (C120921Z04-RP1) Note: 1.The applicant company changed the sensor for the EUT. After the reassessment, the below 1GHz radiated emission was re-tested, the final test result and internal photos were changed. 2. The other information, please refer to the Report No.: SZ120705B01-RP and this report. FCC ID: HQXAXM-Q6 Page 2/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 TABLE OF CONTENTS 1 TEST CERTIFICATION ...........................................................................................4 2 EUT DESCRIPTION.................................................................................................5 3 TEST METHODOLOGY...........................................................................................6 3.1. DESCRIPTION OF TEST MODES.......................................................................................6 4 TEST METHODOLOGY...........................................................................................7 4.1. EUT EXERCISE ...................................................................................................................7 4.2. FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS............................................7 5 INSTRUMENT CALIBRATION ................................................................................8 6 SETUP OF EQUIPMENT UNDER TEST .................................................................8 6.1. DESCRIPTION OF SUPPORT UNITS.................................................................................8 6.2. CONFIGURATION OF SYSTEM UNDER TEST..................................................................8 7 FACILITIES AND ACCREDITATIONS ....................................................................9 7.1. FACILITIES ..........................................................................................................................9 7.2. ACCREDITATIONS..............................................................................................................9 7.3. MEASUREMENT UNCERTAINTY .......................................................................................9 8 FCC PART 15.249 REQUIREMENTS ...................................................................10 8.1. BAND EDGES MEASUREMENT .......................................................................................10 8.2. POWER LINE CONDUCTED EMISSIONS MEASUREMENT ...........................................12 8.3. SPURIOUS EMISSIONS MEASUREMENT .......................................................................19 FCC ID: HQXAXM-Q6 Page 3/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 1 TEST CERTIFICATION Product Wireless Mini BlueScan Mouse Model AXM-Q6 / 00033 Brand Sysgration / TUMI Tested July 5~10, 2012 & September 20~21, 2012 Sysgration Ltd. Applicant 10FL, NO.868-3, Chung Rd, Chung Ho, Taipei, Taiwan, R.O.C. Sysgration (Shenzhen) Ltd. Manufacturer Egongling Village, Pinghu Town, Longgang Dist. Shenzhen City. China APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted DEVIATION FROM APPLICABLE STANDARD None We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4:2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.249. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Tom Gan Aven Zhou Supervisor of EMC Dept. Supervisor of Report Dept. Compliance Certification Service Inc. Compliance Certification Service Inc. FCC ID: HQXAXM-Q6 Page 4/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 2 EUT DESCRIPTION Product Wireless Mini BlueScan Mouse Model AXM-Q6 / 00033 Brand Sysgration / TUMI All models are identical to each other, the brand name and the model names are different. Model Discrepancy 1. The brand name of the model AXM-Q6 is Sysgration; 2. The brand name of the model 00033 is TUMI. Identify Number C120921Z04-RP1 Power Supply DC3V supplied by the battery Frequency Range 2405-2476 MHz Peak: 84.31dBuV/m (Max.) Transmit Power Average: 60.84dBuV/m (Max.) Modulation Technique GFSK Number of Channels 64 Channels Antenna Specification PCB Antenna with 2.0dBi gain(MAX) Temperature Range 0°C ~ +40°C Note: 1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: HQXAXM-Q6 filing to comply with Section 15.207, 15.209 and 15.249 of the FCC Part 15, Subpart C Rules. FCC ID: HQXAXM-Q6 Page 5/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 3 TEST METHODOLOGY 3.1. DESCRIPTION OF TEST MODES The EUT had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting and receiving mode is programmed. The following test mode(s) were scanned during the preliminary test below 1G: Test Item Test mode Worse mode Not applicable since the EUT Conducted Emission supplied by the battery. Radiated Emission Mode 1: TX After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in normal link mode only. Channel Low (2405MHz), Channel Mid (2439MHz) and Channel High (2476MHz) were chosen for the final testing. The field strength of spurious radiation emission was measured in the following position: EUT stand-up position (Y mode) and lie-down position (X, Z mode) The following data show only the worst case setup. The worst case (X axis) was reported. FCC ID: HQXAXM-Q6 Page 6/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 4 TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4:2009 and FCC CFR 15.209 and 15.249. 4.1. EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.209,15.249 under the FCC Rules Part 15 Subpart C. 4.2. FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 ( 2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. FCC ID: HQXAXM-Q6 Page 7/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 5 INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 6 SETUP OF EQUIPMENT UNDER TEST 6.1. DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Equipment Model No. Serial No. FCC ID Brand Data Cable Power Cord 1 N/A Note: 1) Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 6.2. CONFIGURATION OF SYSTEM UNDER TEST See test photographs attached in Appendix II for the actual connections between EUT and support equipment. FCC ID: HQXAXM-Q6 Page 8/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 7 FACILITIES AND ACCREDITATIONS 7.1. FACILITIES All measurement facilities used to collect the measurement data are located at No.10-1, Mingkeda Logistics Park, No.18, Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.4:2009, ANSI C63.7 and CISPR Publication 22. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” 7.2. ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. USA A2LA China CNAS The measuring facility of laboratories has been authorized or registered by the following approval agencies. USA FCC Japan VCCI(C-3478, R-3135, T-652) Canada INDUSTRY CANADA Taiwan BSMI Norway Nemko Copies of granted accreditation certificates are available for downloading from our web site, http://www.ccsrf.com 7.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Measurement Frequency Uncertainty Conducted emissions 9kHz~30MHz +/- 3.18dB 30MHz ~ 200MHz +/- 3.79dB Radiated emissions 200MHz ~1000MHz +/- 3.62dB Above 1000MHz +/- 5.04dB Band Edges +/-0.182 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. The measured result is above (below) the specification limit by a margin less than the measurement uncertainty; it is therefore not possible to state compliance based on the 95% level of confidence. However, the result indicates that compliance (non-compliance) is more probable than non-compliance) with the specification limit. FCC ID: HQXAXM-Q6 Page 9/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8 FCC PART 15.249 REQUIREMENTS 8.1. BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Field Strength Field Strength Frequency (Hz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 2. As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. 3. As shown in Section 15.249(d) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. MEASUREMENT EQUIPMENT USED Radiated Emission Test Site 966（2） Name of Model Serial Last Due Manufacturer Equipment Number Number Calibration Calibration PSA Series Spectrum Agilent E4446A US44300399 03/19/2012 03/19/2013 Analyzer ESCI EMI TEST ROHDE&SCHWARZ ESCI 100783 03/17/2012 03/17/2013 RECEIVE.ESCI Amplifier MITEQ AM-1604-3000 1123808 03/18/2012 03/18/2013 Turn Table EMCO 2081-1.21 N/A N.C.R N.C.R Controller CT N/A N/A N.C.R N.C.R High Noise Amplifier Agilent 8449B 3008A01838 03/18/2012 03/18/2013 Bilog Antenna SCHAFFNER CBL6143 5082 03/17/2012 03/17/2013 Horn Antenna SCHWARZBECK BBHA9120 D286 03/17/2012 03/17/2013 Loop Antenna A、R、A PLA-1030/B 1029 03/23/2012 03/23/2013 Temp. / Humidity Meter VICTOR VC230 N/A 03/19/2012 03/19/2013 Antenna Tower SUNOL TLT2 N/A N.C.R N.C.R Test S/W FARAD LZ-RF / CCS-SZ-3A2 Remark: Each piece of equipment is scheduled for calibration once a year. FCC ID: HQXAXM-Q6 Page 10/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Test Configuration Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m 30cm Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=510Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. FCC ID: HQXAXM-Q6 Page 11/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Test Data Band Edges (CH-Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical FCC ID: HQXAXM-Q6 Page 12/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal FCC ID: HQXAXM-Q6 Page 13/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Band Edges (CH-High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical FCC ID: HQXAXM-Q6 Page 14/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal FCC ID: HQXAXM-Q6 Page 15/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.2. POWER LINE CONDUCTED EMISSIONS MEASUREMENT 8.2.1. LIMITS OF CONDUCTED EMISSIONS MEASUREMENT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. (3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 8.2.2. TEST INSTRUMENTS Conducted Emission Test Site Serial Last Due Name of Equipment Manufacturer Model Number Number Calibration Calibration ESCI EMI TEST ROHDE&SCHWARZ ESCI 100783 03/17/2012 03/17/2013 RECEIVE.ESCI LISN(EUT) SCHAFFNER NNB42 2001/001 03/19/2012 03/19/2013 LISN EMCO 3825/2 8901-1459 03/19/2012 03/19/2013 Temp. / Humidity Meter VICTOR HTC-1 2 03/20/2012 03/20/2013 Test S/W FARAD EZ-EMC/ CCS-3A1-CE NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. FCC ID: HQXAXM-Q6 Page 16/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.2.3. TEST PROCEDURES (please refer to measurement standard) z The EUT and Support equipment, if needed, was placed on a non-conducted table, which is 0.8m above the ground plane and 0.4m away from the conducted wall. z The test equipment EUT installed received AC main power, through a Line Impedance Stabilization Network (LISN), which supplied power source and was grounded to the ground plane. All support equipment power received from a second LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. z The EUT test program was started. Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT. z The frequency range from 150 kHz to 30 MHz was searched. The test data of the worst-case condition(s) was recorded. Emission levels under limit 20dB were not recorded. FCC ID: HQXAXM-Q6 Page 17/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.2.4. TEST SETUP Vert. reference plane EMI receiver 40cm EUT 80cm LISN Reference ground plane z For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 8.2.5. DATA SAMPLE Frequency QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Remark Reading Reading Factor Result Result Limit Limit Margin Margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) (Pass/Fail) X.XXXX 32.69 25.65 11.52 44.21 37.17 65.78 55.79 -21.57 -18.62 Pass Factor = Insertion loss of LISN + Cable Loss Result = Quasi-peak Reading/ Average Reading + Factor Limit = Limit stated in standard Margin = Result (dBuV) – Limit (dBuV) 8.2.6. TEST RESULTS Not applicable, since the EUT supplied by the battery. FCC ID: HQXAXM-Q6 Page 18/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.3. SPURIOUS EMISSIONS MEASUREMENT 8.3.1. LIMITS OF RADIATED EMISSIONS MEASUREMENT 1. In the section 15.249(a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Fundamental Field Strength of Fundamental Field Strength of Harmonics Frequency Field Strength (mV/m) (μV/m) 902-928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (μV/m) Measurement Distance (m) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Field Strength Field Strength Frequency (Hz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 FCC ID: HQXAXM-Q6 Page 19/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.3.2. TEST INSTRUMENTS Radiated Emission Test Site 966（2） Model Serial Last Due Name of Equipment Manufacturer Number Number Calibration Calibration PSA Series Spectrum Agilent E4446A US44300399 03/19/2012 03/19/2013 Analyzer ESCI EMI TEST ROHDE&SCHWARZ ESCI 100783 03/17/2012 03/17/2013 RECEIVE.ESCI Amplifier MITEQ AM-1604-3000 1123808 03/18/2012 03/18/2013 Turn Table EMCO 2081-1.21 N/A N.C.R N.C.R Controller CT N/A N/A N.C.R N.C.R High Noise Amplifier Agilent 8449B 3008A01838 03/18/2012 03/18/2013 Bilog Antenna SCHAFFNER CBL6143 5082 03/17/2012 03/17/2013 Horn Antenna SCHWARZBECK BBHA9120 D286 03/17/2012 03/17/2013 Loop Antenna A、R、A PLA-1030/B 1029 03/23/2012 03/23/2013 Temp. / Humidity Meter VICTOR VC230 N/A 03/19/2012 03/19/2013 Antenna Tower SUNOL TLT2 N/A N.C.R N.C.R Test S/W FARAD LZ-RF / CCS-SZ-3A2 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The FCC Site Registration number is 101879. 3. N.C.R = No Calibration Required. 8.3.3 TEST PROCEDURE (please refer to measurement standard) 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. FCC ID: HQXAXM-Q6 Page 20/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.3.2.1. TEST SETUP Below 30MHz Antenna tower 3m Loop antenna EUT 4m Spectrum / Receiver Turntable 1m 0.8m Pre-amp Reference ground plane Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane FCC ID: HQXAXM-Q6 Page 21/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m 30cm Pre-amp For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 8.3.2.2. DATA SAMPLE Below 1GHz Correction Antenna Frequency Reading Result Limit Margin Remark Factor Pole (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (V/H) XXX.XXXX 37.47 -16.41 21.06 40.00 -18.94 V QP Above 1GHz Correction Antenna Frequency Reading Result Limit Margin Remark Factor Pole (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (V/H) XXXX.XXXX 55.54 4.56 60.10 74.00 -13.90 V Peak XXXX.XXXX 29.66 4.56 34.22 54.00 -19.78 V AVG Frequency (MHz) = Emission frequency in MHz Reading (dBuV) = Uncorrected Analyzer / Receiver reading Correction Factor (dB/m) = Antenna factor + Cable loss – Amplifier gain Result (dBuV/m) = Reading (dBuV) + Corr. Factor (dB/m) Limit (dBuV/m) = Limit stated in standard Margin (dB) = Result (dBuV/m) – Limit (dBuV/m) Q.P. = Quasi-peak Reading Peak = Peak Reading AVG = Average Reading FCC ID: HQXAXM-Q6 Page 22/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 8.3.2.3. TEST RESULTS Below 1 GHz Operation Mode: TX Test Date: September 20, 2012 Temperature: 24°C Tested by: Sunday Hu Humidity: 52% RH Polarity: Ver. / Hor. Frequency Reading Correction Result Limit Margin Antenna Factor Pole Remark (MHz) (dBμV) (dB/m) (dBμV/m) (dBμV/m) (dB) (V/H) 363.0332 33.77 -16.63 17.14 46.00 -28.86 V QP 495.6000 33.33 -13.93 19.40 46.00 -26.60 V QP 686.3667 32.77 -11.74 21.03 46.00 -24.97 V QP 791.4500 33.36 -10.30 23.06 46.00 -22.94 V QP 860.9664 33.41 -9.31 24.10 46.00 -21.90 V QP 961.2000 32.65 -8.63 24.02 54.00 -29.98 V QP 295.1333 35.94 -19.19 16.75 46.00 -29.25 H QP 569.9664 34.28 -12.54 21.74 46.00 -24.26 H QP 613.6167 35.68 -12.23 23.45 46.00 -22.55 H QP 796.3000 33.48 -10.34 23.14 46.00 -22.86 H QP 827.0167 33.11 -9.73 23.38 46.00 -22.62 H QP 961.2000 33.73 -8.63 25.10 54.00 -28.90 H QP Remark: No emission found between lowest internal used/generated frequency to 30MHz. Notes: 1. Measuring frequencies from 9kHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30MHz to 1GHz were made with an instrument using Peak/Quasi-peak detector mode. 3. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 4. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. FCC ID: HQXAXM-Q6 Page 23/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Above 1 GHz Operation Mode: TX / CH Low Test Date: July 5, 2012 Temperature: 24°C Tested by: Sunday Hu Humidity: 52% RH Polarity: Ver. / Hor. Fundamental Frequency Reading Correction Result Limit Margin Antenna Remark (MHz) Factor (dB) Pole (dBuV) (dB/m) (dBuV/m) (dBuV/m) (V/H) 2405.0000 91.47 -9.72 81.75 114.00 -32.25 V Peak 2405.0000 67.75 -9.72 58.03 94.00 -35.97 V AVG 2405.0000 94.03 -9.72 84.31 114.00 -29.69 H Peak 2405.0000 70.56 -9.72 60.84 94.00 -33.16 H AVG Frequency Reading Correction Result Limit Margin Antenna Remark Factor Pole (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (V/H) 1450.0000 48.16 -7.38 40.78 74.00 -33.22 V Peak 2890.0000 46.73 -3.70 43.03 74.00 -30.97 V Peak 3235.0000 46.45 -2.98 43.47 74.00 -30.53 V Peak 4135.0000 45.68 -0.58 45.10 74.00 -28.90 V Peak 4810.0000 52.94 1.83 54.77 74.00 -19.23 V Peak 4810.0000 34.42 1.83 36.25 54.00 -17.75 V AVG 5230.0000 45.35 2.92 48.27 74.00 -25.73 V Peak 1390.0000 48.82 -7.22 41.60 74.00 -32.40 H Peak 1525.0000 47.37 -7.70 39.67 74.00 -34.33 H Peak 2935.0000 47.08 -3.52 43.56 74.00 -30.44 H Peak 3685.0000 45.83 -1.66 44.17 74.00 -29.83 H Peak 4300.0000 45.78 0.09 45.87 74.00 -28.13 H Peak 4810.0000 53.19 1.83 55.02 74.00 -18.98 H Peak 4810.0000 34.76 1.83 36.59 54.00 -17.41 H AVG REMARKS: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). FCC ID: HQXAXM-Q6 Page 24/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Operation Mode: TX / CH Mid Test Date: July 5, 2012 Temperature: 24°C Tested by: Sunday Hu Humidity: 52% RH Polarity: Ver. / Hor. Fundamental Frequency Reading Correction Result Limit Margin Antenna Remark (MHz) Factor (dB) Pole (dBuV) (dB/m) (dBuV/m) (dBuV/m) (V/H) 2439.0000 91.64 -9.77 81.87 114.00 -32.13 V Peak 2439.0000 68.20 -9.77 58.43 94.00 -35.57 V AVG 2439.0000 93.46 -9.77 83.69 114.00 -30.31 H Peak 2439.0000 70.29 -9.77 60.52 94.00 -33.48 H AVG Frequency Reading Correction Result Limit Margin Antenna Remark Factor Pole (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (V/H) 1360.0000 48.15 -7.37 40.78 74.00 -33.22 V Peak 3040.0000 46.86 -3.21 43.65 74.00 -30.35 V Peak 3760.0000 45.79 -1.55 44.24 74.00 -29.76 V Peak 4375.0000 45.10 0.47 45.57 74.00 -28.43 V Peak 4885.0000 49.89 2.16 52.05 74.00 -21.95 V Peak 5710.0000 45.09 3.92 49.01 74.00 -24.99 V Peak 1465.0000 49.63 -7.45 42.18 74.00 -31.82 H Peak 3205.0000 46.43 -2.99 43.44 74.00 -30.56 H Peak 3490.0000 46.21 -2.41 43.80 74.00 -30.20 H Peak 3895.0000 46.34 -1.21 45.13 74.00 -28.87 H Peak 4405.0000 44.76 0.62 45.38 74.00 -28.62 H Peak 4885.0000 51.35 2.16 53.51 74.00 -20.49 H Peak REMARKS: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). FCC ID: HQXAXM-Q6 Page 25/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services

Reference No.: SZ120705B01-RP Report No.: C120921Z04-RP1 Operation Mode: TX / CH High Test Date: July 5, 2012 Temperature: 24°C Tested by: Sunday Hu Humidity: 52% RH Polarity: Ver. / Hor. Fundamental Frequency Reading Correction Result Limit Margin Antenna Remark (MHz) Factor (dB) Pole (dBuV) (dB/m) (dBuV/m) (dBuV/m) (V/H) 2476.0000 91.74 -9.78 81.96 114.00 -32.04 V Peak 2476.0000 68.60 -9.78 58.82 94.00 -35.18 V AVG 2476.0000 92.96 -9.78 83.18 114.00 -30.82 H Peak 2476.0000 69.87 -9.78 60.09 94.00 -33.91 H AVG Frequency Reading Correction Result Limit Margin Antenna Remark Factor Pole (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (V/H) 1360.0000 49.35 -7.37 41.98 74.00 -32.02 V Peak 2845.0000 47.29 -3.88 43.41 74.00 -30.59 V Peak 3310.0000 47.17 -2.95 44.22 74.00 -29.78 V Peak 3790.0000 46.79 -1.50 45.29 74.00 -28.71 V Peak 4525.0000 44.79 1.15 45.94 74.00 -28.06 V Peak 4945.0000 48.52 2.42 50.94 74.00 -23.06 V Peak 2110.0000 47.40 -7.72 39.68 74.00 -34.32 H Peak 3325.0000 48.07 -2.95 45.12 74.00 -28.88 H Peak 3835.0000 46.76 -1.39 45.37 74.00 -28.63 H Peak 4660.0000 44.47 1.57 46.04 74.00 -27.96 H Peak 4945.0000 50.29 2.42 52.71 74.00 -21.29 H Peak 5665.0000 45.09 3.77 48.86 74.00 -25.14 H Peak REMARKS: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). FCC ID: HQXAXM-Q6 Page 26/26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services


Document Created: 2012-09-21 16:00:42
Document Modified: 2012-09-21 16:00:42
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC