Test report

FCC ID: HQKKMEMAC233MA

Test Report

Download: PDF
FCCID_1966091

TEST REPORT of FCC Part 15 Subpart C New Application; Class I PC; Class II PC Product : Wireless Mouse; 2.4GHz High Performance Wireless Mouse Brand: N/A Model: MA-C233; MA-xxyy (x=0~9, A~Z; y=0~9, A~Z); GM-M7580; GK-KM7580 Model Difference: Market segmentation FCC ID: HQKKMEMAC233MA FCC Rule Part: §15.249 Applicant: Key Mouse Electronic Enterprise Co., Ltd. Address: No. 3, Wugung 5th Rd., Sinijhuang District, New Taipei City, Taiwan Test Performed by: International Standards Laboratory <Lung-Tan LAB> *Site Registration No. BSMI: SL2-IN-E-0013; MRA TW1036; TAF: 0997; IC: IC4067B-3; *Address: No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan *Tel : 886-3-407-1718; Fax: 886-3-407-1738 Report No.: ISL-13LR068FC Issue Date : 2013/05/03 Test results given in this report apply only to the specific sample(s) tested and are traceable to national or international standard through calibration of the equipment and evaluating measurement uncertainty herein. This report MUST not be used to claim product endorsement by TAF, NVLAP or any agency of the Government. This test report shall not be reproduced except in full, without the written approval of International Standards Laboratory. Page: 1 of 25

-2 of 25- FCC ID: HQKKMEMAC233MA VERIFICATION OF COMPLIANCE Applicant: Key Mouse Electronic Enterprise Co., Ltd. Product Description: Wireless Mouse; 2.4GHz High Performance Wireless Mouse Brand Name: N/A FCC ID: HQKKMEMAC233MA FCC Rule Part: §15.249 MA-C233; MA-xxyy (x=0~9, A~Z; y=0~9, A~Z); Model No.: GM-M7580; GK-KM7580 Model Difference: Market segmentation Date of test: 2013/04/21 ~2013/04/25 Date of EUT Received: 2013/04/21 We hereby certify that: All the tests in this report have been performed and recorded in accordance with the standards described above and performed by an independent electromagnetic compatibility consultant, International Standards Laboratory. The test results contained in this report accurately represent the measurements of the characteristics and the energy generated by sample equipment under test at the time of the test. The sample equipment tested as described in this report is in compliance with the limits of above standards. Test By: Date: 2013/05/03 Dion Chang / Engineer Prepared By: Date: 2013/05/03 Eva Kao / Technical Supervisor Approved By: Date: 2013/05/03 Vincent Su / Technical Manager International Standards Laboratory Report Number: ISL-13LR068FC

-3 of 25- FCC ID: HQKKMEMAC233MA Version Version No. Date Description 00 2013/05/03 Initial creation of document International Standards Laboratory Report Number: ISL-13LR068FC

-4 of 25- FCC ID: HQKKMEMAC233MA Table of Contents 1 GENERAL INFORMATION ........................................................................................... 5 1.1 PRODUCT DESCRIPTION .................................................................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT (S) ............................................................................................... 5 1.3 TEST METHODOLOGY........................................................................................................................ 5 1.4 TEST FACILITY .................................................................................................................................. 5 1.5 SPECIAL ACCESSORIES ...................................................................................................................... 5 1.6 EQUIPMENT MODIFICATIONS ............................................................................................................ 5 2 SYSTEM TEST CONFIGURATION .............................................................................. 6 2.1 EUT CONFIGURATION ....................................................................................................................... 6 2.2 EUT EXERCISE .................................................................................................................................. 6 2.3 TEST PROCEDURE .............................................................................................................................. 6 2.4 MEASUREMENT EQUIPMENT USED: .................................................................................................. 7 2.5 LIMITATION ....................................................................................................................................... 8 2.6 CONFIGURATION OF TESTED SYSTEM ............................................................................................. 10 3 SUMMARY OF TEST RESULTS ................................................................................. 11 4 DESCRIPTION OF TEST MODES .............................................................................. 11 5 CONDUCTED EMISSIONS TEST ............................................................................... 12 5.1 MEASUREMENT PROCEDURE: ......................................................................................................... 12 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 12 5.3 MEASUREMENT EQUIPMENT USED: ................................................................................................ 12 5.4 MEASUREMENT RESULT: ................................................................................................................ 12 6 RADIATED EMISSION TEST ...................................................................................... 13 6.1 MEASUREMENT PROCEDURE........................................................................................................... 13 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 13 6.3 MEASUREMENT EQUIPMENT USED: ................................................................................................ 14 6.4 FIELD STRENGTH CALCULATION..................................................................................................... 14 6.5 MEASUREMENT RESULT.................................................................................................................. 15 7 20 DB BAND WIDTH MEASUREMENT .................................................................... 23 7.1 MEASUREMENT PROCEDURE........................................................................................................... 23 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 23 7.3 MEASUREMENT EQUIPMENT USED: ................................................................................................ 23 7.4 MEASUREMENT RESULTS:............................................................................................................... 23 International Standards Laboratory Report Number: ISL-13LR068FC

-5 of 25- FCC ID: HQKKMEMAC233MA 1 GENERAL INFORMATION 1.1 Product Description Product Name: Wireless Mouse; 2.4GHz High Performance Wireless Mouse Brand Name: N/A MA-C233; MA-xxyy (x=0~9, A~Z; y=0~9, A~Z); GM-M7580; Model Name: GK-KM7580 Model Difference: Market segmentation Operation Frequency: 2408 MHz ~ 2474 MHz Channel number: 34 channels, step 2MHz Modulation Type: GFSK Power Supply: 3V DC from AAA battery *2 Antenna Designation: Printed Antenna 1.2 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: HQKKMEMAC233MA filing to comply with Section 15.249 of the FCC Part 15, Subpart C Rules. 1.3 Test Methodology Both conducted and radiated testing was performed according to the procedures in ANSI C63.4 (2003). Radiated testing was performed at an antenna to EUT distance 3 meters. 1.4 Test Facility The measurement facilities used to collect the 3m Radiated Emission and AC power line conducted data are located on the address of International Standards Laboratory <Lung-Tan LAB> No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd., Lung-Tan Hsiang, Tao Yuan County 325, Taiwan which are constructed and calibrated to meet the FCC requirements in documents ANSI C63.4: 2003. FCC Registration Number is: TW1036, Canada Registration Number: 4067B-3. 1.5 Special Accessories Not available for this EUT intended for grant. 1.6 Equipment Modifications Not available for this EUT intended for grant. International Standards Laboratory Report Number: ISL-13LR068FC

-6 of 25- FCC ID: HQKKMEMAC233MA 2 System Test Configuration 2.1 EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. 2.2 EUT Exercise The Transmitter was operated in the engineering operating mode. the Tx frequency was fixed which was for the purpose of the measurements. 2.3 Test Procedure 2.3.1 Conducted Emissions The EUT is a placed on as turn table which is 0.8 m above ground plane. According to the requirements in Section 7 and 13 of ANSI C63.4-2003.Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-Peak and Average detector mode. 2.3.2 Radiated Emissions The EUT is a placed on as turn table which is 0.8 m above ground plane. The turn table shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the max. emission, the relative positions of this hand-held transmitter(EUT) was rotated through three orthogonal axes according to the requirements in Section 8 and 13 of ANSI C63.4-2003. International Standards Laboratory Report Number: ISL-13LR068FC

-7 of 25- FCC ID: HQKKMEMAC233MA 2.4 Measurement Equipment Used: Conducted Emission Test Site EQUIPMENT MFR MODEL SERIAL LAST CAL DUE. TYPE NUMBER NUMBER CAL. Conduction 03 -1 WOKEN CFD 300-NL Conduction 0-1 06/28/2012 06/28/2013 Cable ROHDE & EMI Receiver 12 ESCI 100804 07/13/2012 07/13/2013 SCHWARZ FCC-LISN-50-100-4- LISN 07 FCC Inc. 07040 07/13/2012 07/13/2013 02 FCC-LISN50-25-2-0 LISN 08 FCC 07039 07/13/2012 07/13/2013 1 Chamber 14(966) EQUIPMENT MFR MODEL SERIAL LAST CAL DUE. TYPE NUMBER NUMBER CAL. Spectrum Analyzer 21(26.5GHz) Agilent N9010A MY49060537 07/17/2012 07/16/2013 Spectrum Analyzer Agilent E4443A MY48250315 05/24/2012 05/23/2013 20(6.5GHz) Spectrum Analyzer R&S FSU43 100143 04/25/2012 04/24/2013 22(43GHz) Loop Antenna9K-30M A.H.SYSTEM SAS-564 294 03/07/2013 03/06/2015 BILOG Antenna Schaffner CBL6112B 2756 01/11/2013 01/10/2014 08(30~1G) Horn antenna1-18G(06) EMCO 3117 0006665 10/15/2012 10/14/2013 Horn antenna26-40G(05) Com-power AH-640 100A 01/09/2013 01/08/2015 Horn antenna18-26G(04) Com-power AH-826 081001 05/04/2011 05/03/2013 Preamplifier9-1000M HP 8447D NA 02/19/2013 02/18/2014 AFS44-001018 Preamplifier1-18G MITEQ 00-25-10P-44 1329256 07/23/2012 07/22/2013 Preamplifier1-26G EM EM01M26G NA 02/26/2013 02/25/2014 JS-26004000-2 Preamplifier26-40G MITEQ 818471 05/21/2011 05/20/2013 7-5A Cable1-18G HUBER SUHNER Sucoflex 106 NA 09/07/2012 09/06/2013 Cable UP to 1G HUBER SUHNER RG 214/U NA 10/08/2012 10/07/2013 SUCOFLEX 27963/2&3742 HUBER SUHNER Sucoflex 102 09/21/2011 09/20/2013 1GHz~40GHz cable 1/2 2.4G Filter Micro-Tronics Brm50702 76 12/27/2012 12/26/2013 International Standards Laboratory Report Number: ISL-13LR068FC

-8 of 25- FCC ID: HQKKMEMAC233MA 2.5 Limitation (1) Conducted Emission According to section 15.207(a) Conducted Emission Limits is as following. Frequency Conducted Limit (dBuV) (MHz) Quasi-Peak Average 0.15 – 0.5 66 - 56 56 - 46 0.5 – 5 56 46 5 - 30 60 50 (2) Radiated Emission 15.249(a) The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following. Frequency Field strength of Field strength of Distance (m) (MHz) Fundamental Harmonics 902 - 928 50 mV/m 500 uV/m 3 (94dBuV/m) (54dBuV/m) 2400 – 2483.5 50 mV/m 500 uV/m 3 (94dBuV/m) (54dBuV/m) 5725 – 5875 50 mV/m 500 uV/m 3 (94dBuV/m) (54dBuV/m) 24.0 – 24.25 GHz 250 mV/m 2500 uV/m 3 (107.95dBuV/m) (67.95dBuV/m) International Standards Laboratory Report Number: ISL-13LR068FC

-9 of 25- FCC ID: HQKKMEMAC233MA (3) Radiated Emission15.249 (d) Emission Radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50dB below the level of the fundamental or to the general radiated emission limits in Section 15.209 as below, whichever is the lesser attenuation. Frequency Field strength Distance (m) Field strength at 3m (MHz) µV/m dBµµV/m 1.705-30 30 30 69.54 30-88 100 3 40 88-216 150 3 43.5 216-960 200 3 46 Above 960 500 3 54 (4) Radiated Emission 15.249(e) For frequencies above 1000MHz, the above field strength limits are based on average limits. The peak filed strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20dB under any condition of modulation. Remark: 1. Emission level in dBuV/m=20 log (uV/m) 2. Measurement was performed at an antenna to the closed point of EUT distance of meters. 3. Only spurious frequency is permitted to locate within the Restricted Bands specified in provision of ξ 15.205 4. Emission spurious frequency which appearing within the Restricted Bands specified in provision of ξ15.205, then the general radiated emission limits in ξ 15.209 apply. International Standards Laboratory Report Number: ISL-13LR068FC

-10 of 25- FCC ID: HQKKMEMAC233MA 2.6 Configuration of Tested System Fig. 2-1 Configuration of Radiated Emission Test EUT Table 2-1 Equipment Used in Tested System No Unit Model / Serial No. Brand Power Cord FCC ID 1 N/A Note: All the above equipment/cables were placed in worse case positions to maximize emission signals during emission test. Grounding: Grounding was in accordance with the manufacturer’s requirements and conditions for the intended use. International Standards Laboratory Report Number: ISL-13LR068FC

: fRA9 emalonalSarcacs acoany —11 of 25— FCC ID: HQKKMEMAC233MA 3 Summary of Test Results FCC Rules Description Of Test Result §15.207 Conducted Emission N/A §15.249(a)(d)(e) Radiated Emission Compliant §15.215 (c ) 20dB band width Measurement Compliant 4 Description of test modes The EUT has been tested under operating condition with new battery. The EUT is staying in continuous transmitting mode Channel low (2408MHz) > mid (2440MHz) and high (2474MHz) with highest data rate are chosen for full testing. International Standards Laboratory Report Number: ISL—13LRO68FC

-12 of 25- FCC ID: HQKKMEMAC233MA 5 Conducted Emissions Test 5.1 Measurement Procedure: 1. The EUT was placed on a table which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. 5.2 Test SET-UP (Block Diagram of Configuration) E F B C D A 10cm 10cm 80cm A : PC LISN LISN B : Monitor (EUT) 40cm C : Printer D : Modem E : Keyboard F : Mouse to Test Receiver Fig. 2 5.3 Measurement Equipment Used: Refer to section 2.4 in this report 5.4 Measurement Result: N/A, This device was used DC power supply. International Standards Laboratory Report Number: ISL-13LR068FC

-13 of 25- FCC ID: HQKKMEMAC233MA 6 Radiated Emission Test 6.1 Measurement Procedure 1. The EUT was placed on a turntable that is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measured were complete. 6.2 Test SET-UP (Block Diagram of Configuration) (A) Radiated Emission Test Set-Up, Frequency Below 1000MHz 3m Turntable EUT 1m to 4m Spectrum Analyzer 0.8m Ground Plane Coaxial Cable (B) Radiated Emission Test Set-UP Frequency Over 1 GHz Turntable 3m EUT Test 0.8 m 1m to 4m Receiver Ground Plane Coaxial Cable International Standards Laboratory Report Number: ISL-13LR068FC

-14 of 25- FCC ID: HQKKMEMAC233MA 6.3 Measurement Equipment Used: Refer to section 2.4 in this report 6.4 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor(if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CL - AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor International Standards Laboratory Report Number: ISL-13LR068FC

—15 of 25— FCC ID: HQKKMEMAC233MA 6.5 Measurement Result Fundamental Measurement Result Operation Mode : TX CH Low, Mid, High Test Date :2013/04/24 Fundamental Frequency : 2408, 2440, 2474MHz Test By : Dino Temp 125 C Hum. : 60% . hus Over No Freq Reading Factor Level Limit Limit Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 1 2408.00 90.04 —6.97 83.07 114.00 —30.93 Peak VERTICAL 1 2408.00 |_98.05 —6.97 91.08 114.00 —22.92 Peak HORIZONTAL No Freq Reading Factor Level Limit 8;:; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 1 2440.00 88.91 —6.90 82.01 114.00 —31.99 Peak VERTICAL 1 2440.00 96.86 —6.90 89.96 114.00 —24.04 Peak HORIZONTAL No Freq Reading Factor Level Limit 8;:; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 1| 2474.00 |_87.57 —6.83 80.74 114.00 —33.26 Peak VERTICAL 1| 2474.00 95.70 —6.83 88.87 114.00 —25.13 Average HORIZONTAL Remark: 1 Measuring frequencies from the lowest internal frequency to the 10th of fundamental frequency 2 Field strength limits for frequency above 1000MHz are based on average limits. However, Peak mode field strength shall not exceed the average limits specified plus 20dB. 3 "F" denotes fundamental frequency; "H" denotes harmonics frequency. "S" denotes spurious frequency. 4 Measurement of data within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Spectrum Peak mode IF bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, Sweep time= 200 ms., the VBW setting was 3 MHz. 6 Spectrum AV mode if bandwidth Setting : 1GHz— 26GHz, RBW= 1IMHz, VBW= 10Hz, Sweep time= 200 ms. International Standards Laboratory Report Number: ISL—13LRO68FC

—16 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (below 1GHz) Operation Mode : TX CH Low Test Date : 2013/04/24 Fundamental Frequency : 2408 MHz Test By : Dino Temp 125 C Hum. : 60% No Freq Reading Factor Level Limit 8;:11; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 1 170.65 26.73 |—14.16| 12.57 43.50 —30.93 Peak VERTICAL 2 |472.32 26.50 —8.77 17.73 46.00 —28.27 Peak VERTICAL 3 625.58 26.82 —5.68 21.14 46.00 —24.86 Peak VERTICAL 4 747.80 27.03 —3.12 23.91 46.00 —22.09 Peak VERTICAL 5 839.95 26.12 —2.20 23.92 46.00 —22.08 Peak VERTICAL 6 915.61 2641 —0.81 25.60 46.00 —20.40 Peak VERTICAL 1 |136.70 26.03 —14.20 11.83 43.50 —31.67 Peak HORIZONTAL 2 356.89 25.77 |—10.95 14.82 46.00 —31.18 Peak HORIZONTAL 3 514.03 |_25.55 —8.21 17.34 46.00 —28.66 Peak HORIZONTAL 4 |688.63 27.16 —4.67 2249 46.00 —23.51 Peak HORIZONTAL 5 §46.74 25.15 —2.13 23.02 46.00 —22.98 Peak HORIZONTAL 6 941.80 26.15 —0.42 25.73 46.00 —20.27 Peak HORIZONTAL Remark: 1 No further spurious emissions detected from the lowest internal frequency and 30MHz. 2 Measuring frequencies from the lowest internal frequency to the 1GHz. 3 Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak / QP detector mode. 4 Measurement result within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 The IF bandwidth of SPA between 30MHz to 1GHz was 100KHz. VBW=300KHz. International Standards Laboratory Report Number: ISL—13LRO68FC

—17 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (below 1GHz) Operation Mode : TX CH Mid Test Date : 2013/04/24 Fundamental Frequency : 2440 MHz Test By : Dino Temp 125 C Hum. : 60% No Freq Reading Factor Level Limit 8;:11; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 1 |151.25 25.13 |—13.32] 11.81 43.50 —31.69 Peak VERTICAL 2 |387.93 26.29 |—10.31| 15.98 46.00 —30.02 Peak VERTICAL 3 627.52 26.36 —5.65 20.71 46.00 —25.29 Peak VERTICAL 4 75847 25.54 —3.00 2254 46.00 —23.46 Peak VERTICAL 5 853.53 24.89 —2.01 22.88 46.00 —23.12 Peak VERTICAL 6 935.98 25.80 —0.50 25.30 46.00 —20.70 Peak VERTICAL 1 |156.10 24.94 |—13.28 11.66 43.50 —31.84 Peak HORIZONTAL 2 |417.03 2542 —9.74 15.68 46.00 —30.32 Peak HORIZONTAL 3 524.10 2745 —7.99 19.46 46.00 —26.54 Peak HORIZONTAL 4 |708.03 26.28 —4.26 22.02 46.00 —23.98 Peak HORIZONTAL 5 889.42 25.57 —1.24 24.33 46.00 —21.67 Peak HORIZONTAL 6 |936.95 25.50 —0.49 25.01 46.00 —20.99 Peak HORIZONTAL Remark: 1 No further spurious emissions detected from the lowest internal frequency and 30MHz. 2 Measuring frequencies from the lowest internal frequency to the 1GHz. 3 Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak / QP detector mode. 4 Measurement result within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 The IF bandwidth of SPA between 30MHz to 1GHz was 100KHz. VBW=300KHz. International Standards Laboratory Report Number: ISL—13LRO68FC

—18 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (below 1GHz) Operation Mode : TX CH High Test Date : 2013/04/24 Fundamental Frequency :2474 MHz Test By : Dino Temp ©125 0C Hum. : 60% No Freq Reading Factor Level Limit 8\r]nelrt Remark Pol MHz dBuV dB dBuV/m dBuV/m _dB V/H 1 364.65 26.24 |—10.75 15.49 46.00 —30.51 Peak VERTICAL 2 60230 26.64 —6.06 20.58 46.00 —25 42 Peak VERTICAL 3 715.79 25.08 —4.04 21.04 46.00 —24.96 Peak VERTICAL 4 §05.03 25.68 —2.61 23.07 46.00 —22.93 Peak VERTICAL 5 891.36 26.43 —1.21 25.22 46.00 —20.78 Peak VERTICAL 6 |983.51 25.12 —0.09 25.03 54.00 —28.97 Peak VERTICAL 1 14349 25.05 |—13.62 11.43 43.50 —32.07 Peak HORIZONTAL 2 398.60 25.59 |—10.18 15.41 46.00 —30.59 Peak HORIZONTAL 3 584.84 25.71 —6.51 19.20 46.00 —26.80 Peak HORIZONTAL 4 659.53 26.22 —5.14 21.08 46.00 —24.92 Peak HORIZONTAL 5 868.08 26.03 —1.70 24.33 46.00 —21.67 Peak HORIZONTAL 6 |970.90 25.77 —0.18 25.59 54.00 —2841 Peak HORIZONTAL Remark: 1 No further spurious emissions detected from the lowest internal frequency and 30MHz. 2 Measuring frequencies from the lowest internal frequency to the 1GHz. 3 Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak / QP detector mode. 4 Measurement result within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 The IF bandwidth of SPA between 30MHz to 1GHz was 100KHz. VBW=300KHz. International Standards Laboratory Report Number: ISL—13LRO68FC

—19 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (above 1GHz) Operation Mode : TX CH Low Test Date : 2013/04/24 Fundamental Frequency : 2408 MHz Test By : Dino Temp ©125 0C Hum. : 60% No Freq Reading Factor Level Limit 8;:; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m _dB V/H 4816.00 44.42 1.29 45.71 74.00 —28.29 Peak VERTICAL 2 7224.00 40.96 7.93 48.89 74.00 —25.11 Peak VERTICAL 4816.00 45.13 1.29 4642 74.00 —27.58 Peak HORIZONTAL 2 7224.00 39.20 7.93 47.13 74.00 —26.87 Peak HORIZONTAL Remark: 1 Measuring frequencies from the lowest internal frequency to the 10th of fundamental frequency 2 Field strength limits for frequency above 1000MHz are based on average limits. However, Peak mode field strength shall not exceed the average limits specified plus 20dB. 3 "F" denotes fundamental frequency; "H" denotes harmonics frequency. "S" denotes spurious frequency. 4 Measurement of data within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Spectrum Peak mode IF bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, Sweep time= 200 ms., the VBW setting was 3 MHz. 6 Spectrum AV mode if bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, VBW= 10Hz, Sweep time= 200 ms. International Standards Laboratory Report Number: ISL—13LRO68FC

—20 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (above 1GHz) Operation Mode : TX CH Mid Test Date : 2013/04/24 Fundamental Frequency : 2440 MHz Test By : Dino Temp ©125 0C Hum. : 60% No Freq Reading Factor Level Limit 8;:; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m _dB V/H 4880.00 44.94 1.48 4642 74.00 —27.58 Peak VERTICAL 2 7320.00 39.57 8.03 47.60 74.00 —26.40 Peak VERTICAL 4880.00 41.45 1.48 42.93 74.00 —31.07 Peak HORIZONTAL 2 7320.00 36.01 8.03 44.04 74.00 —29.96 Peak HORIZONTAL Remark: 1 Measuring frequencies from the lowest internal frequency to the 10th of fundamental frequency 2 Field strength limits for frequency above 1000MHz are based on average limits. However, Peak mode field strength shall not exceed the average limits specified plus 20dB. 3 "F" denotes fundamental frequency; "H" denotes harmonics frequency. "S" denotes spurious frequency. 4 Measurement of data within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Spectrum Peak mode IF bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, Sweep time= 200 ms., the VBW setting was 3 MHz. 6 Spectrum AV mode if bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, VBW= 10Hz, Sweep time= 200 ms. International Standards Laboratory Report Number: ISL—13LRO68FC

—21 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (above 1GHz) Operation Mode : TX CH High Test Date : 2013/04/24 Fundamental Frequency : 2474 MHz Test By : Dino Temp ©125 0C Hum. : 60% No Freq Reading Factor Level Limit 8;:; Remark Pol MHz dBuV dB_ dBuV/m dBuV/m _dB V/H 4948.00 44.68 1.70 46.38 74.00 —27.62 Peak VERTICAL 2 7422.00 38.97 8.13 47.10 74.00 —26.90 Peak VERTICAL 4948.00 46.58 1.70 48.28 74.00 —25.72 Peak HORIZONTAL 2 7422.00 36.91 8.13 45.04 74.00 —28.96 Peak HORIZONTAL Remark: 1 Measuring frequencies from the lowest internal frequency to the 10th of fundamental frequency 2 Field strength limits for frequency above 1000MHz are based on average limits. However, Peak mode field strength shall not exceed the average limits specified plus 20dB. 3 "F" denotes fundamental frequency; "H" denotes harmonics frequency. "S" denotes spurious frequency. 4 Measurement of data within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Spectrum Peak mode IF bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, Sweep time= 200 ms., the VBW setting was 3 MHz. 6 Spectrum AV mode if bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, VBW= 10Hz, Sweep time= 200 ms. International Standards Laboratory Report Number: ISL—13LRO68FC

—22 of 25— FCC ID: HQKKMEMAC233MA Radiated Spurious Emission Measurement Result (Band Edge) Operation Mode : Band Edge Test Date : 2013/04/24 Temp./Hum. :25 °C/:60% Test By : Dino CH Low . hus Over No Freq Reading Factor Level Limit Limit Remark Pol MHz dBuV dB_ dBuV/m dBuV/m dB V/H 2382.30 |_51.75 —7.03 44.72 74.00 —29.28 Peak VERTICAL 2 2390.00 47.78 —7.01 40.77 74.00 —33.23 Peak VERTICAL 2382.70 |_57.88 —7.03 50.85 74.00 —23.15 Peak HORIZONTAL 2 2390.00 53.30 —7.01 46.29 74.00 —27.71 Peak HORIZONTAL CH High . us Over No Freq Reading Factor Level Limit Limit Remark Pol MHz dBuV dB dBuV/m dBuV/m dB V/H 2483.50 47.58 —6.81 40.77 74.00 —33.23 Peak VERTICAL 2 2487.71 49.10 —6.79 42.31 74.00 —31.69 Peak VERTICAL 2 2483.50 |_53.29 —6.81 4648 74.00 —27.52 Peak HORIZONTAL Remark: 1 Measuring frequencies from the lowest internal frequency to the 10th of fundamental frequency 2 Field strength limits for frequency above 1000MHz are based on average limits. However, Peak mode field strength shall not exceed the average limits specified plus 20dB. 3 "F" denotes fundamental frequency; "H" denotes harmonics frequency. "S" denotes spurious frequency. 4 Measurement of data within this frequency range shown " — " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Spectrum Peak mode IF bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, Sweep time= 200 ms., the VBW setting was 3 MHz. 6 Spectrum AV mode if bandwidth Setting : 1GHz— 26GHz, RBW= 1MHz, VBW= 10Hz, Sweep time= 200 ms. International Standards Laboratory Report Number: ISL—13LRO68FC

-23 of 25- FCC ID: HQKKMEMAC233MA 7 20 dB Band Width Measurement 7.1 Measurement Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Set EUT normal operating mode. 3. Set SPA Center Frequency = fundamental frequency, RBW = 100kHz, VBW = 300kHz, Span =10MHz. 4. Set SPA Max hold. Mark peak, -20dB. 7.2 Test SET-UP (Block Diagram of Configuration) Same as 4.2 Radiated Emission Measurement. 7.3 Measurement Equipment Used: Same as 4.2 Radiated Emission Measurement. 7.4 Measurement Results: 2408 Channel = 1.651MHz 2440 Channel = 1.666MHz 2474 Channel = 1.687MHz Refer to attached data chart. International Standards Laboratory Report Number: ISL-13LR068FC

-24 of 25- FCC ID: HQKKMEMAC233MA 20dB Bandwidth Test Data CH-Low 20dB Bandwidth Test Data CH-Mid International Standards Laboratory Report Number: ISL-13LR068FC

-25 of 25- FCC ID: HQKKMEMAC233MA 20dB Bandwidth Test Data CH-High International Standards Laboratory Report Number: ISL-13LR068FC


Document Created: 2013-05-09 17:39:24
Document Modified: 2013-05-09 17:39:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC