Compliance Opinion

FCC ID: HN2PC24-11

Cover Letter(s)

Download: PDF
FCCID_290377

Northwest EMC TCB Approval Opinion Revision 05/9/02 Information about the Applicant Company Name Intermec Corp. Address 6001 36th Avenue West City, State, Zip Everett, WA 98203-9280 Requested By Cheryl White Job Number INMC0036 Model PC24-11-FC/R FCC ID HN2PC24-11 Agent Applicant Approval Type Reference Northwest EMC Technical Report – General Information Equipment Type Reference Northwest EMC Technical Report – General Information Rule Part Reference Northwest EMC Technical Report – General Information Overview The application is for the PC24-11-FC/R radio module, which operates in the 2.4-2.4835 GHz band as a direct sequence spread spectrum transmitter under Section 15.247. This RF module is compliant with IEEE 802.11b specifications, and will be used only as a mobile transmitter. The radio is provided to Intermec Technologies Corporation by Agere Systems. Agere Systems has provided the information regarding the Theory of Operation, Schematics and Block Diagram for this certification application. Intermec’s 802.11(b) Transmitter, FCC ID: HN2PC24-11 is seeking FCC authorization as a modular transmitter. The EUT meets the requirements for modular approval as detailed in FCC Public Notice DA00-1407. Compliance to each of the requirements is described in the letter included with this application package, Exhibit T. General Comments The TCB 410, Application for Certification is incorrect, it states 0.032 W for output power, Item the test data shows 0.0374 W. A corrected application must be submitted. Resolution A corrected application has been provided. The FCC requires that the highest gain of each type of antenna, plus the lowest gain antenna overall must be tested for radiated spurious emissions. Several antennas were Item tested; Yagi, flat panel, corner reflector, omni, dipole, flag, and patch antennas. Please provide additional information demonstrating that each of the antennas listed is one of those “types” of antennas, or additional test data for the “types” of antennas not tested. Resolution Additional information has been provided, reference Exhibit G. INMC0036

Northwest EMC TCB Approval Opinion Revision 05/9/02 To satisfy the modular approval requirements of item 6 in the FCC Public Notice DA 00- 1407, a drawing or photo of the label used on the outside of the host device must be provided with the application. Excerpt from DA 00-1407: "The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior Item label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization." Resolution Additional information has been provided, reference Exhibit A. The antenna information exhibit did not specifically address how the antenna connector Item requirements of 15.203 were met. (e.g. reverse polarity SMA connectors, etc.) Resolution Additional information has been provided, reference Exhibit V. The Operational Description stated a frequency range of 2412-2462 MHz, the applicant Item cover letter states 2400-2483 MHz, please correct the conflicting information. Resolution The applicant has provided further clarification, this is no longer and issue. The CE module states testing was performed in the 450 kHz – 30 MHz range, the data Item actually shows testing was conducted over the 150 kHz – 30 MHz range. Resolution The information has been corrected. Conducted emissions data states a CISPR 22 method, it should be tested using ANSI Item C63.4 methods. Resolution The information has been corrected. Conducted Emissions data states input power of 5 VDC, the module specifies the Item equipment is tested in a PC powered by 120 VAC/60 Hz. Resolution The information has been corrected. The CE module describes testing in a Host Laptop PC, the EUT and peripheral description Item and setup photos describes different equipment. Resolution The information has been corrected. The CE data includes redundant data, there is separate data sheets for peak and then QP Item and AV data, the peak data sheets are not required when the additional data is provided. Resolution The information has been corrected. INMC0036

Northwest EMC TCB Approval Opinion Revision 05/9/02 Opinion Specification Requirements Description 15.207 Conducted Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit L Specification Requirements Description 15.247(a) Bandwidth Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit N Specification Requirements Description 15.247(b) Power Output Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit Q Specification Requirements Description 15.247( c ) Spurious Emissions, Antenna Conducted Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit P Specification Requirements Description 15.247( c ) Spurious Emissions, Radiated Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit R INMC0036

Northwest EMC TCB Approval Opinion Revision 05/9/02 Specification Requirements Description 15.247(d) Power Spectral Density Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report Reference: Exhibit O Specification Requirements Description 15.247(b)(4) RF Exposure Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted MPE estimates demonstrating compliance. Reference: Exhibit H INMC0036


Document Created: 2002-12-17 15:50:07
Document Modified: 2002-12-17 15:50:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC