MPE

FCC ID: HLZWPC3

RF Exposure Info

Download: PDF
FCCID_3899594

Report No.: ER/2018/50050 Page: 1 of 7 1 MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Standard Applicable According to §1.1307(b)(1) and , systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to §1.1310 and §2.1093 RF exposure is calculated. According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: FCC KDB 680106 1.2 Limits for Maximum Permissive Exposure (MPE) Frequency Electric Field Magnetic Field Power Density Averaging Time Range Strength(E) (V/m) Strength(H) (A/m) (mW/cm2) (minute) (MHz) Limits for Occupational / Controlled Exposure 0.3-3.0 614 1.63 *(100) 6 3.0-30 1842/f 4.89/f *(900/f2 ) 6 30-300 61.4 0.163 1.0 6 300-1500 / / F/300 6 1500-15000 / / 5 6 Frequency Electric Field Magnetic Field Power Density Averaging Time Range Strength(E) (V/m) Strength(H) (A/m) (mW/cm2) (minute) (MHz) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / F/1500 30 1500-15000 / / 1.0 30 F = frequency in MHz * = Plane-wave equipment power density Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group

Report No.: ER/2018/50050 Page: 2 of 7 1.3 Equipment Used in Tested System Model Item Equipment Mfr/Brand Series No. Data Cable Power Cord /Type No. 1. NA --- --- --- --- --- 1.4 The Worst Charging Condition: Ancillary Equipment Charging Condition Verdict Load Full Loading PASS Load 99% Loading PASS Load 50% Loading PASS Load 1% Loading PASS Note: For Wireless Power Consortium Qi specification, a lower operating frequency or high duty cycle result in the transfer of a higher amount of power and charging current. 1.5 Measurement Procedure: 1. For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance of 15 cm and 20 cm. E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm and 20 cm measured from the center of the probe(s) to the edge of the device. Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63 A/m. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group

Report No.: ER/2018/50050 Page: 3 of 7 1.6 Measurement Equipment Used: EQUIPMENT MFR MODEL SERIAL LAST CAL DUE. TYPE NUMBER NUMBER CAL. EM RADIATION Wandel& EMR-30 M-0006 10/14/2017 10/13/2018 METER Goltermann 1.7 Test Set-up: 1.8 Maximum Permissible Exposure (MPE) Evaluation: Full Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 15 cm 6.75 0.023 Left 15 cm 6.98 0.029 Right 15 cm 6.38 0.039 Top 15 cm 6.33 0.033 Bottom 15 cm 6.98 0.031 Limit 614 1.63 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group

Report No.: ER/2018/50050 Page: 4 of 7 99% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 15 cm 6.98 0.031 Left 15 cm 6.55 0.039 Right 15 cm 6.33 0.032 Top 15 cm 6.12 0.033 Bottom 15 cm 6.09 0.021 Limit 614 1.63 50% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 15 cm 6.03 0.033 Left 15 cm 6.34 0.035 Right 15 cm 6.55 0.039 Top 15 cm 6.53 0.031 Bottom 15 cm 6.43 0.028 Limit 614 1.63 1% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 15 cm 6.33 0.033 Left 15 cm 6.77 0.04 Right 15 cm 6.34 0.033 Top 15 cm 6.98 0.037 Bottom 15 cm 6.93 0.034 Limit 614 1.63 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group

Report No.: ER/2018/50050 Page: 5 of 7 Full Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 20 cm 6.12 0.03 Left 20 cm 6.23 0.026 Right 20 cm 6.32 0.033 Top 20 cm 6.44 0.029 Bottom 20 cm 6.54 0.028 Limit 614 1.63 99% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 20 cm 6.21 0.032 Left 20 cm 6.24 0.035 Right 20 cm 6.44 0.04 Top 20 cm 6.45 0.027 Bottom 20 cm 6.21 0.026 Limit 614 1.63 50% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 20 cm 6.32 0.021 Left 20 cm 6.37 0.032 Right 20 cm 6.13 0.023 Top 20 cm 6.36 0.021 Bottom 20 cm 6.44 0.021 Limit 614 1.63 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group

Report No.: ER/2018/50050 Page: 6 of 7 1% Loading Maximum Permissible Exposure Probe from EUT Side Test Distance E-field H-field Front 20 cm 6.12 0.022 Left 20 cm 6.03 0.019 Right 20 cm 6.22 0.021 Top 20 cm 6.12 0.019 Bottom 20 cm 6.17 0.012 Limit 614 1.63 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group


Document Created: 2018-06-12 10:10:33
Document Modified: 2018-06-12 10:10:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC