Modular Approval Request

FCC ID: HLZLS1

Cover Letter(s)

Download: PDF
FCCID_4431702

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: HLZLS1 Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes. The EUT provides the RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Yes. The EUT has its buffered are provided) to ensure that the module will comply with Part 15 requirements modulation. Please see the under conditions of excessive data rates or over-modulation. RF IC datasheet 6.1. RX and TX FIFOs 3. The modular transmitter must have its own power supply regulation. Yes. The EUT has its own power supply regulation. Please see the Schematic Diagram. 4. The modular transmitter must comply with the antenna requirements of Section Yes. The EUT meets the FCC 15.203 and 15.204(b)(c). The antenna must either be permanently attached or antenna requirements; spiral employ a “unique” antenna coupler (at all connections between the module and the antenna is welding on the antenna, including the cable). EUT. Please see the photographs which are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Yes. The EUT was testes in a module must not be inside another device during testing. This is intended to stand-alone configuration. demonstrate that the module is capable of complying with Part 15 emission limits Please see photographs of test regardless of the device into which it is eventually installed. configuration in the test report. 6. The modular transmitter must be equipped with either a permanently affixed label Yes. Please see exhibition or must be capable of electronically displaying its FCC identification number in label sample for the FCC ID accordance with 15.212 (a)(1)(vi)(A) / (B). of this module. And there are instructions gives to the OEM on how to label the end product 7. The modular transmitter must comply with any specific rule or operating Yes. The EUT is compliant requirements applicable to the transmitter and the manufacturer must provide with all applicable FCC rules. adequate instructions along with the module to explain any such requirements. A Details instructions for copy of these instructions must be included in the application for equipment maintaining compliance are authorization. For example, there are very strict operational and timing given in the User Manual. requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure Yes. The EUT is compliant requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and with RF exposure specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and requirement. RF exposure is 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices addressed in the RF exposure perform routine environmental evaluation for RF Exposure to demonstrate exhibition. compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance.

RF_734_02 04 April 16 Items to be covered by Split modular transmitters. Answer from applicant 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): RU Jan Date: August 8, 2019 Signature: ___________________________


Document Created: 2019-08-29 18:49:26
Document Modified: 2019-08-29 18:49:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC