HAC H Probe

FCC ID: HLZDME210SC

Test Report

Download: PDF
FCCID_1409410

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multitateral Agreementfor the recognition of calibration certificates Client CCS—TW (Auden) Certificate No: H3—6163_Apr10 CALIBRATION CERTIFICATE Object H3DV6 — SN:6163 Calibration procedure(s) QA CAL—03.v5 and QA CAL—25.v2 Calibration procedure for H—field probes optimized for close near field evaluations in air Calibration date: April 26, 2010 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 & 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter E4419B GB41293874 1—Apr—10 (No. 217—01136) Apr—11 Power sensor E4412A MY41495277 1—Apr—10 (No. 217—01136) Apr—11 Power sensor E4412A MY41498087 1—Apr—10 (No. 217—01136) Apr—11 Reference 3 dB Aftenuator SN: 55054 (3c) 30—Mar—10 (No. 217—01159) Mar—11 Reference 20 dB Attenuator SN: 55086 (20b) 30—Mar—10 (No. 217—01161) Mar—11 Reference 30 dB Attenuator SN: $5129 (30b) 30—Mar—10 (No. 217—01160) Mar—11 Reference Probe H3DV6 SN: 6182 3—0ct—09 (No. H3—6182_0ct09) Oct—10 DAE4 SN: 789 23—Dec—09 (No. DAE4—789_Dec09) Dec—10 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator HP 8648C US3642U01700 4—Aug—99 (in house check Oct—09) In house check: Oct—11 Network Analyzer HP 8753E US37390585 18—0ct—01 (in house cht_ack Oct—09) In house check: Oct10 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician Approved by: Katia Pokovie Technical Manager /@%_\ Issued: April 27, 2010 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: H3—6163_Apr10 Page 1 of 10

Calibration Laboratory of «il77 Schweizerischer Kalibrierdienst Schmid & Partner ilfié Service suisse d‘étalonnage Engineering AG Ts Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ns Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: NORMx,y,z sensitivity in free space DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B,C modulation dependentlinearization parameters Polarization q «p rotation around probe axis Polarization 8 8 rotation around an axis thatis in the plane normal to probe axis (at measurement center), .e., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1309—2005, " IEEE Standard for calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz", December 2005. Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 8 = 0 for XY sensors and 8 = 90 for Z sensor(f < 900 MHz in TEM—cell; f> 1800 MHz: R22 waveguide). X,Y,2(0)_adata2= X,Y,Z2_a0ata2* frequency_response (see Frequency Response Chart). DCPx,y,z; DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. Ax,y,2; Bx,y,z; Cx,y,z, VRx,y,z: A, B, C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. Spherical isotropy (3D deviation from isotropy}: in a locally homogeneous field realized using an open waveguide setup. Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the X_aOa1a2 (no uncertainty required). Certificate No: H3—6163_Apr10 Page 2 of 10

H3DV6 SN:6163 April 26, 2010 Probe H3DVC6 SN:6163 Manufactured: January 1, 2005 Last calibrated: April 27, 2009 Recalibrated: April 26, 2010 Calibrated for DASY Systems (Note: non—compatible with DASY2 system!) Certificate No: H3—6163_Apr10 Page 3 of 10

H3DV6 SN:6163 April 26, 2010 DASY — Parameters of Probe: H3DVG6 SN:6163 Basic Calibration Parameters Sensor X] Sensor Y Sensor 2 |Unc (k=2) Norm (A/m / \/(pV)) a0| 2.65E—3| 2.60E—3 3.14E—3 £5.1% Norm (A/m / \/(pV)) all 1.04E—5| 3.78E—5 —1.32E4|] £5.1% Norm (A/m / \/(pV)) a2| —4.99E—5| —6.56E—5 1.50E—5 £5.1% DCP (my)* 82.3 95.5 83.3 Modulation Calibration Parameters UID Communication System Name PAR A B C VR Unc® dB dBuV mV (k=2) 10000 CW 0.00 x 0.00 0.00 1.00| 300 £15% Y 0.00 0.00 1.00 300 Z 0.00 0.00 1.00 300 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * numerical linearization parameter: uncertainty not required & Uncertainty is determined using the maximum deviation from linear response applying recatangular distribution and is expressed for the square of the field value. Certificate No: H3—6163_Apr10 Page 4 of 10

H3DV6 SN:6163 April 26, 2010 Frequency Response of H—Field (TEM—Cell:ifi110 EXX, Waveguide R22) 14 1.3 1.2 Frequency response (normalized) 14 10 ::I:Ifl:_:§| 0.9 0.8 0.7 0.6 0 500 1000 1500 2000 2500 3000 £ [MHz] xy: —@—TEM —B—R22 z: —6—TEM —R—R22 Uncertainty of Frequency Response of H—field: * 6.3% (k=2) Certificate No: H3—6163_Apr10 Page 5 of 10

H3DV6 SN:6163 April 26, 2010 Receiving Pattern (¢), 9 = 90° f = 600 MHz, TEM ifi110EXX f= 2500 MHz, WG R22 —#—X —#—Y —@—Z —O—iot ~@—X ~@—¥ ~@—20 ~O—tot Receiving Pattern (¢), 9 = 0° f= 600 MHz, TEM ifi110EXX f= 2500 MHz, WG R22 —O—tot ~O—tot Certificate No: H3—6163_Apr10 Page 6 of 10

H3DV6 SN:6163 April 26, 2010 Receiving Pattern (¢), 9 = 90° 1.0 0.8 g'j —6—300 MHz mon —BI—600 MHz io 0.2 —&—750 MHz 2 oo 8 o» —BI— 1800 MHz 4 o4 —i—2500 MHz —0.6 —0.8 —1.0 1 7 13 19 25 31 (AW! Uncertainty of Axial Isotropy Assessment: £ 0.5%(k=2) ivi — Receiving Pattern (¢), 8 = 0° 1.0 0.8 0.6 0.4 —0—300 MHz ® o2 —BI—600 MHz 2 o0 —4—750 MHz 2 .02 —BI— 1800 MHz 4 .04 —&— 2500 MHz —0.6 —0.8 —1.0 0 60 120 180 240 300 $11 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: H3—6163_Apr10 Page 7 of 10

H3DV6 SN:6163 April 26, 2010 Other Probe Parameters Sensor Arrangement Rectangular Connector Angle (°) —255.2 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 20 mm Tip Diameter 6.0 mm Probe Tip to Sensor X Calibration Point 3 mm Probe Tip to Sensor Y Calibration Point 3 mm Probe Tip to Sensor Z Calibration Point 3 mm Certificate No: H3—6163_Apr10 Page 10 of 10


Document Created: 2019-09-13 11:19:44
Document Modified: 2019-09-13 11:19:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC