User Manual

FCC ID: HKX-THE-EGG

Users Manual

Download: PDF
FCCID_2142449

           IMPORTANT SAFETY & REGULATORY INFORMATION
        DO NOT DISCARD – DOCUMENT MUST REMAIN WITH DEVICE
                                ENGINEERING DEVELOPMENT DEVICE
                                    NOT FOR RESALE OR LEASE
                              This device is intended for Engineering Use Only!
This device has not been tested or approved by any agency or approvals body for Electrical Safety,
Electromagnetic Compatibility, or Telecommunications at the time of distribution.
Safety Testing and Certification that may be required for installation and operation in your region has not been
completed.

SAFETY WARNINGS and CAUTIONS - Please pay attention to the following warnings and or cautions


Lithium Battery: This device contains a non-replaceable Lithium Battery. There is a risk of explosion if
the battery is replaced by an incorrect type.

General Use and Set Up: Care must be taken at all times to avoid dropping, spilling, or allowing objects to be placed
on the device.
FCC Regulations: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Operation on the 5.15-5.25Ghz frequency band is restricted to indoor use only. The FCC requires indoor use for the
5.15-5.25 band to reduce the potential for harmful interference to co-channel Mobile Satellite Systems.

This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio
or television equipment reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna
-Move the equipment away from the receiver
-Plug the equipment into an outlet on a circuit different from that to which the receiver is connected
-Consult the dealer or an experienced radio/television technician for additional suggestions

You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible
for compliance could void the authority to operate such equipment.

RF Exposure Information: This device is compliant with SAR requirement for general population / uncontrolled
exposure limits in ANSI/IEEE C95.1-1999 and has been tested in accordance with the measurement methods and
procedures specified in FCC OET Bulletin 65 Supplement C.

This equipment complies with the FCC RF exposure limits set forth for uncontrolled environments.


Page 1 of 2


Wireless (RF) Interface: This development system may include a wireless (Radio Frequency, RF) transmitter. Prior
to approval or registration of this system with the spectrum management or communications authority (e.g. the FCC),
operation of the transmitter may be restricted or prohibited by regional or national regulations, a license for
experimental use may be required. Operation of the system in a shielded room or enclosure is recommended to reduce
the likelihood of interference. For compliance with RF exposure limits, the antennas used for this transmitter must be
installed to provide a separation distance of at least 20cm (8 inches) from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.

Lead Content:




This device complies with the European Union RoHS directive; some components may internally include lead
(Pb) as allowed by exemption. All second level inter-connect (2LI) connections between components and PCBs
are lead free.
Please recycle this device in a responsible manner. Refer to local environmental
regulations for proper recycling; do not dispose of device in unsorted municipal waste.




Page 2 of 2



Document Created: 2013-12-10 11:43:54
Document Modified: 2013-12-10 11:43:54

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC