RF Test Report-BLE

FCC ID: HFSQTA-9560NGW

Test Report

Download: PDF
FCCID_4128302

Partial FCC Test Report Report No.: RF180921C06-1 FCC ID: HFSQTA-9560NGW Test Model: D11 Received Date: Sep. 21, 2018 Test Date: Oct. 29, 2018 ~ Dec. 27, 2018 Issued Date: Dec. 28, 2018 Applicant: Quanta Computer Inc. Address: No.188, Wenhua 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location: B2F., No.215, Sec. 3, Beixin Rd., Xindian Dist., New Taipei City, Taiwan FCC Registration / 427177 / TW0011 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF180921C06-1 Page No. 1 / 26 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes..................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 8 3.3 Description of Support Units ............................................................................................................... 10 3.3.1 Configuration of System under Test ......................................................................................... 10 3.4 General Description of Applied Standards .......................................................................................... 10 4 Test Types and Results ............................................................................................................................. 11 4.1 Radiated Emission and Bandedge Measurement ............................................................................... 11 4.1.1 Limits of Radiated Emission and Bandedge Measurement ...................................................... 11 4.1.2 Test Instruments ....................................................................................................................... 12 4.1.3 Test Procedures ........................................................................................................................ 13 4.1.4 Deviation from Test Standard ................................................................................................... 13 4.1.5 Test Set Up ............................................................................................................................... 14 4.1.6 EUT Operating Conditions ........................................................................................................ 15 4.1.7 Test Results .............................................................................................................................. 16 4.2 Conducted Emission Measurement .................................................................................................... 20 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 20 4.2.2 Test Instruments ....................................................................................................................... 20 4.2.3 Test Procedures ........................................................................................................................ 20 4.2.4 Deviation from Test Standard ................................................................................................... 21 4.2.5 Test Setup ................................................................................................................................. 21 4.2.6 EUT Operating Conditions ........................................................................................................ 21 4.2.7 Test Results .............................................................................................................................. 22 4.3 Conducted Output Power Measurement ............................................................................................ 24 4.3.1 Limits of Conducted Output Power Measurement.................................................................... 24 4.3.2 Test Setup ................................................................................................................................. 24 4.3.3 Test Instruments ....................................................................................................................... 24 4.3.4 Test Procedures ........................................................................................................................ 24 4.3.5 Deviation from Test Standard ................................................................................................... 24 4.3.6 EUT Operating Conditions ........................................................................................................ 24 4.3.7 Test Results .............................................................................................................................. 24 5 Pictures of Test Arrangements................................................................................................................ 25 Appendix – Information on the Testing Laboratories ................................................................................ 26 Report No.: RF180921C06-1 Page No. 2 / 26 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF180921C06-1 Original Release Dec. 28, 2018 Report No.: RF180921C06-1 Page No. 3 / 26 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Notebook Computer Brand: Quanta Test Model: D11 Sample Status: ENGINEERING SAMPLE Applicant: Quanta Computer Inc. Test Date: Oct. 29, 2018 ~ Dec. 27, 2018 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Dec. 28, 2018 Gina Liu / Specialist Approved by : , Date: Dec. 28, 2018 Dylan Chiou / Project Engineer Report No.: RF180921C06-1 Page No. 4 / 26 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -7.93 dB at 0.17734 MHz. Meet the requirement of limit. 15.205 & 209 Radiated Emissions Pass Minimum passing margin is -4.02 dB at 51.33 MHz. 15.247(d) Band Edge Measurement N/A Refer to Note 15.247(d) Antenna Port Emission N/A Refer to Note 15.247(a)(2) 6 dB Bandwidth N/A Refer to Note --- Occupied Bandwidth Measurement N/A Refer to Note 15.247(b) Conducted Power Pass Meet the requirement of limit. 15.247(e) Power Spectral Density N/A Refer to Note 15.203 Antenna Requirement N/A Refer to Note Note: This report is a partial report, only test item of Radiated Emissions, Conducted Emission tests and Conducted Power were performed for this report. Other testing data please refer to Intel report no.: 170524-02.TR04 for module (Brand: Intel, Model: 9560NGW). 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expended Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 2.44 dB 30 MHz ~ 200 MHz 2.0153 dB Radiated Emissions up to 1 GHz 200 MHz ~ 1000 MHz 2.0224 dB 1 GHz ~ 18 GHz 1.0121 dB Radiated Emissions above 1 GHz 18 GHz ~ 40 GHz 1.1508 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF180921C06-1 Page No. 5 / 26 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Notebook Computer Brand Quanta Test Model D11 Status of EUT ENGINEERING SAMPLE 5 or 9 or 15 or 20 Vdc (adapter) Power Supply Rating 11.55 Vdc (battery) Modulation Type GFSK Transfer Rate 1 Mbps Operating Frequency 2402 ~ 2480 MHz Number of Channel 40 Output Power 7.295 mW Antenna Type Refer to Note as below Antenna Connector N/A Accessory Device Refer to Note as below Data Cable Supplied N/A Note: 1. The WLAN/BT module (Brand: Intel, Model: 9560NGW) was installed in the EUT. 2. The antenna information is listed as below. Antenna Gain (dBi) Antenna WLAN WLAN WLAN Manuf. Mode Parts Number BT/WLAN 5.15~5.35 5.47~5.725 5.725~5.85 Type 2.4GHz GHz GHz GHz Main: -1.68 Main: 1.58 Main: 0.93 Main: 0.67 Tablet Main Antenna: Aux.: -0.73 Aux.: -0.78 Aux.: -0.15 Aux.: -0.17 DQ60ANF6Y18 (ANF6Y-100060) PIFA AWAN Aux. Antenna: DQ60ANF6Y19 (ANF6Y-100061) Main: -2.63 Main: 1.93 Main: 0.18 Main: -0.02 NB Aux.: -2.28 Aux.: 1.95 Aux.: 0.44 Aux.: 0.74 3. The EUT contains following accessory devices. Product Brand Model Description I/P: 100-240 Vac, 50-60 Hz, 1.2 A O/P: 5 Vdc, 3 A, 9 Vdc, 3 A, 15 Vdc, 3 Adapter Chicony A16-045N1A A, 20 Vdc, 2.25 A, 45W Max. 1.45M/0 core Battery SIMPLOTECHNOLOGY COLTD 916QA112H 11.5 Vdc, 4940 mAh 4. The above EUT information is declared by manufacturer and for more detailed features description, please refers to the manufacturer's specifications or User's Manual. Report No.: RF180921C06-1 Page No. 6 / 26 Report Format Version: 6.1.1

3.2 Description of Test Modes 40 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF180921C06-1 Page No. 7 / 26 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE1G RE<1G PLC APCM - √ √ √ √ - Where RE1G: Radiated Emission above 1 GHz RE<1G: Radiated Emission below 1 GHz PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement Note: The EUT had been pre-tested on the positioned of each 3 axis and NB mode. The worst case was found when positioned on Z-plane. Note: The worst case was found when positioned on NB mode for Output Power test. Note: “-”means no effect. Radiated Emission Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 19 GFSK 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 19 GFSK 1 Report No.: RF180921C06-1 Page No. 8 / 26 Report Format Version: 6.1.1

Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Test Condition: Applicable To Environmental Conditions Input Power Tested by RE1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Karl Lee RE<1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Karl Lee PLC 25 deg. C, 65 % RH 120 Vac, 60 Hz Thomas Wei APCM 25 deg. C, 65 % RH 120 Vac, 60 Hz Frank Chiu Report No.: RF180921C06-1 Page No. 9 / 26 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. 3.3.1 Configuration of System under Test EUT (Power from AC Adapter) *Test Table 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) KDB 558074 D01 15.247 Meas Guidance v05 ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF180921C06-1 Page No. 10 / 26 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20 dB below the highest level of the desired power: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20 dB under any condition of modulation. Report No.: RF180921C06-1 Page No. 11 / 26 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver N9038A MY51210203 Mar. 16, 2018 Mar. 15, 2019 Agilent Technologies Spectrum Analyzer FSU43 101261 Jan. 11, 2018 Jan. 10, 2019 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-616 Dec. 14, 2017 Dec. 13, 2018 SCHWARZBECK HORN Antenna 3117 00143293 Dec. 13, 2017 Dec. 12, 2018 ETS-Lindgren HORN Antenna BBHA 9170 9170-480 Dec. 01, 2017 Nov. 30, 2018 SCHWARZBECK Fixed Attenuator MDCS18N-10 MDCS18N-10-01 Apr. 16, 2018 Apr. 15, 2019 Mini-Circuits Loop Antenna EM-6879 269 Sep. 07, 2018 Sep. 06, 2019 Preamplifier 310N 187226 Jun. 19, 2018 Jun. 18, 2019 Agilent Preamplifier 83017A MY39501357 Jun. 19, 2018 Jun. 18, 2019 Agilent Power Meter ML2495A 1012010 Sep. 05, 2018 Sep. 04, 2019 Anritsu Power Sensor MA2411B 1315050 Sep. 04, 2018 Sep. 03, 2019 Anritsu Cable-CH1-01(RFC RF signal cable -SMS-100-SMS-12 5D-FB Jun. 19, 2018 Jun. 18, 2019 ETS-LINDGREN 0+RFC-SMS-100-S MS-400) RF signal cable Cable-CH1-02(RFC 8D-FB Jun. 19, 2018 Jun. 18, 2019 ETS-LINDGREN -SMS-100-SMS-24) E3 Software NA NA NA 8.130425b Antenna Tower NA NA NA NA MF Turn Table NA NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HsinTien Chamber 1. 3. The horn antenna and preamplifier (model: 83017A) are used only for the measurement of emission frequency above 1 GHz if tested. 4. The IC Site Registration No. is IC7450I-1. Report No.: RF180921C06-1 Page No. 12 / 26 Report Format Version: 6.1.1

4.1.3 Test Procedures For Radiated Emission below 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9 kHz at frequency below 30 MHz. For Radiated Emission above 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30 MHz ~ 1 GHz) / 1.5 meters (for above 1 GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detected function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98 %) or 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF180921C06-1 Page No. 13 / 26 Report Format Version: 6.1.1

4.1.5 Test Set Up <Radiated Emission below 30 MHz> 1m EUT& 3m Support Units Turn Table 80 cm Ground Plane Test Receiver <Radiated Emission 30 MHz to 1 GHz> Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF180921C06-1 Page No. 14 / 26 Report Format Version: 6.1.1

<Radiated Emission above 1 GHz> Ant. Tower 1-4 m Variable EUT& 3m Support Units Turn Table Absorber 150 cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF180921C06-1 Page No. 15 / 26 Report Format Version: 6.1.1

4.1.7 Test Results Above 1 GHz Data: EUT Test Condition Measurement Detail Channel Channel 0 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Karl Lee Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2325.03 42.77 41.26 54 -11.23 31.73 5.3 35.52 250 2 Average 2325.03 51.83 50.32 74 -22.17 31.73 5.3 35.52 250 2 Peak 2402 98 96.27 31.8 5.4 35.47 250 2 Average 2402 98.79 97.06 31.8 5.4 35.47 250 2 Peak 4804 37.81 29.72 54 -16.19 33.96 8.25 34.12 112 160 Average 4804 47.76 39.67 74 -26.24 33.96 8.25 34.12 112 160 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2325.39 41.54 40.03 54 -12.46 31.73 5.3 35.52 153 329 Average 2325.39 51.35 49.84 74 -22.65 31.73 5.3 35.52 153 329 Peak 2402 98.38 96.65 31.8 5.4 35.47 153 329 Average 2402 99.15 97.42 31.8 5.4 35.47 153 329 Peak 4804 36.75 28.66 54 -17.25 33.96 8.25 34.12 146 173 Average 4804 46.46 38.37 74 -27.54 33.96 8.25 34.12 146 173 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2402 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF180921C06-1 Page No. 16 / 26 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Karl Lee Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2363.28 43.76 42.13 54 -10.24 31.76 5.37 35.5 250 2 Average 2363.28 51.97 50.34 74 -22.03 31.76 5.37 35.5 250 2 Peak 2440 97.57 95.72 31.85 5.46 35.46 250 2 Average 2440 98.37 96.52 31.85 5.46 35.46 250 2 Peak 2489.96 41.71 39.7 54 -12.29 31.9 5.53 35.42 250 2 Average 2489.96 52.2 50.19 74 -21.8 31.9 5.53 35.42 250 2 Peak 4880 37.3 29.11 54 -16.7 33.98 8.27 34.06 105 182 Average 4880 47.15 38.96 74 -26.85 33.98 8.27 34.06 105 182 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2363.19 44.4 42.77 54 -9.6 31.76 5.37 35.5 153 329 Average 2363.19 51.82 50.19 74 -22.18 31.76 5.37 35.5 153 329 Peak 2440 98.71 96.86 31.85 5.46 35.46 153 329 Average 2440 99.53 97.68 31.85 5.46 35.46 153 329 Peak 2489.36 41.48 39.47 54 -12.52 31.9 5.53 35.42 153 329 Average 2489.36 51.72 49.71 74 -22.28 31.9 5.53 35.42 153 329 Peak 4880 37.83 29.64 54 -16.17 33.98 8.27 34.06 139 157 Average 4880 47.7 39.51 74 -26.3 33.98 8.27 34.06 139 157 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2440 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF180921C06-1 Page No. 17 / 26 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Karl Lee Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 96.76 94.8 31.88 5.5 35.42 250 2 Average 2480 97.64 95.68 31.88 5.5 35.42 250 2 Peak 2489.6 43.06 41.05 54 -10.94 31.9 5.53 35.42 250 2 Average 2489.6 53.61 51.6 74 -20.39 31.9 5.53 35.42 250 2 Peak 4960 38.55 30.28 54 -15.45 33.99 8.29 34.01 146 127 Average 4960 48.83 40.56 74 -25.17 33.99 8.29 34.01 146 127 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 97.96 96 31.88 5.5 35.42 153 329 Average 2480 98.99 97.03 31.88 5.5 35.42 153 329 Peak 2489.32 43.07 41.06 54 -10.93 31.9 5.53 35.42 153 329 Average 2489.32 53.53 51.52 74 -20.47 31.9 5.53 35.42 153 329 Peak 4960 38.02 29.75 54 -15.98 33.99 8.29 34.01 155 230 Average 4960 48.11 39.84 74 -25.89 33.99 8.29 34.01 155 230 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2480 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF180921C06-1 Page No. 18 / 26 Report Format Version: 6.1.1

9 kHz ~ 30 MHz Data: The amplitude of spurious emissions attenuated more than 20 dB below the permissible value is not required to be report. 30 MHz ~ 1 GHz Worst-Case Data: EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 30 MHz ~ 1 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Quasi-peak (QP) Environmental 25 deg. C, 65 % RH Tested By Harry Hsueh Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 51.33 35.98 52.85 40 -4.02 14.46 0.9 32.23 102 210 Peak 100.2 24.79 43.49 43.5 -18.71 12.28 1.28 32.26 122 165 Peak 216.03 24.48 43.79 46 -21.52 11.27 1.65 32.23 158 174 Peak 330.8 27.34 43.43 46 -18.66 13.81 2.19 32.09 155 195 Peak 503.7 28.54 41.61 46 -17.46 16.4 2.63 32.1 101 187 Peak 744.5 26.27 35.43 46 -19.73 19.76 3.22 32.14 122 132 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 61.05 35.09 53.31 40 -4.91 13.11 0.9 32.23 166 198 Peak 100.47 15.58 34.25 43.5 -27.92 12.31 1.28 32.26 132 175 Peak 177.15 19.96 41.03 43.5 -23.54 9.56 1.61 32.24 142 158 Peak 360.2 21.67 37.16 46 -24.33 14.35 2.26 32.1 101 142 Peak 503.7 31.42 44.49 46 -14.58 16.4 2.63 32.1 155 187 Peak 599.6 27.09 38.49 46 -18.91 17.92 2.87 32.19 101 142 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. The emission levels of other frequencies were very low against the limit. Report No.: RF180921C06-1 Page No. 19 / 26 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-Peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 4.2.2 Test Instruments Date of Due Date of Description & Manufacturer Model No. Serial No. Calibration Calibration Test Receiver ESCI 100613 Dec. 10, 2018 Dec. 09, 2019 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Sep. 05, 2018 Sep. 04, 2019 Woken LISN/AMN ROHDE & SCHWARZ ESH3-Z5 835239/001 Mar. 06, 2018 Mar. 05, 2019 (EUT) LISN/AMN ROHDE & SCHWARZ ESH3-Z5 100311 Aug. 19, 2018 Aug. 18, 2019 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/50 uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20 dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9 kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15 MHz - 30 MHz. Report No.: RF180921C06-1 Page No. 20 / 26 Report Format Version: 6.1.1

4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 4.2.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF180921C06-1 Page No. 21 / 26 Report Format Version: 6.1.1

4.2.7 Test Results CONDUCTED WORST-CASE DATA Detector Function & Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Resolution Average (AV), 9kHz Bandwidth Environmental Input Power 120Vac, 60Hz 25℃, 65%RH Conditions Tested by Thomas Wei Test Date 2018/12/27 Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.17734 9.67 47.01 28.85 56.68 38.52 64.61 54.61 -7.93 -16.09 2 0.24375 9.67 36.70 21.56 46.37 31.23 61.97 51.97 -15.60 -20.74 3 0.29844 9.67 31.45 13.25 41.12 22.92 60.29 50.29 -19.17 -27.37 4 1.76172 9.67 29.35 16.24 39.02 25.91 56.00 46.00 -16.98 -20.09 5 3.75391 9.72 28.99 14.50 38.71 24.22 56.00 46.00 -17.29 -21.78 6 8.90625 9.83 30.70 18.10 40.53 27.93 60.00 50.00 -19.47 -22.07 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180921C06-1 Page No. 22 / 26 Report Format Version: 6.1.1

Detector Function & Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Resolution Average (AV), 9kHz Bandwidth Environmental Input Power 120Vac, 60Hz 25℃, 65%RH Conditions Tested by Thomas Wei Test Date 2018/12/27 Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.18125 9.67 45.26 30.62 54.93 40.29 64.43 54.43 -9.50 -14.14 2 0.25156 9.67 37.05 22.16 46.72 31.83 61.71 51.71 -14.99 -19.88 3 0.30234 9.67 32.00 18.14 41.67 27.81 60.18 50.18 -18.51 -22.37 4 1.58594 9.67 30.27 15.69 39.94 25.36 56.00 46.00 -16.06 -20.64 5 3.35938 9.71 31.13 16.76 40.84 26.47 56.00 46.00 -15.16 -19.53 6 9.95313 9.86 30.94 16.91 40.80 26.77 60.00 50.00 -19.20 -23.23 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180921C06-1 Page No. 23 / 26 Report Format Version: 6.1.1

4.3 Conducted Output Power Measurement 4.3.1 Limits of Conducted Output Power Measurement For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30 dBm) 4.3.2 Test Setup EUT Power Sensor Power Meter Attenuator 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedures A peak power sensor was used on the output port of the EUT. A power meter was used to read the response of the peak power sensor. Record the power level. 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. 4.3.7 Test Results Frequency Peak Power Peak Power Limit Channel Pass / Fail (MHz) (mW) (dBm) (dBm) 0 2402 6.982 8.44 30 Pass 19 2440 7.278 8.62 30 Pass 39 2480 7.295 8.63 30 Pass Report No.: RF180921C06-1 Page No. 24 / 26 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF180921C06-1 Page No. 25 / 26 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF180921C06-1 Page No. 26 / 26 Report Format Version: 6.1.1


Document Created: 2018-12-28 14:20:46
Document Modified: 2018-12-28 14:20:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC