Test Report Part 2

FCC ID: HFS9550015318

Test Report

Download: PDF
FCCID_165191

FCC ID: HFS9550015318 4.5 POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until ROHDE & SCHWARZ TEST ESMI 839379/002 Dec. 28, 2001 RECEIVER HP ATTENUATOR 8496B 3247A18505 Cal. on use HP PLOTTER 7475A 2641V27755 N/A NOTE: 1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF900801R02 49 Issued: August 8, 2001

FCC ID: HFS9550015318 4.5.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator, the bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3 kHz RBW and 30 kHz VBW, set sweep time=span/3kHz. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3KHz for a full response of the mixer in the spectrum analyzer. 4.5.4 TEST SETUP Attenuator EUT SPECTRUM ANALYZER 4.5.5 EUT OPERATING CONDITIONS Same as 4.3.5 Report No.: RF900801R02 50 Issued: August 8, 2001

FCC ID: HFS9550015318 4.5.6 TEST RESULTS EUT Notebook PC MODEL Solo9550 INPUT POWER ENVIRONMENTAL 30 deg. C, 60%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 1005 hPa TESTED BY: Gary Chang CHANNEL RF POWER LEVEL IN MAXIMUM CHANNEL FREQUENCY 3 KHz BW LIMIT PASS/FAIL NUMBER (MHz ) (dBm) (dBm) 1 2412 -7.32 8 PASS 6 2437 -10.90 8 PASS 11 2462 -7.88 8 PASS Report No.: RF900801R02 51 Issued: August 8, 2001

FCC ID: HFS9550015318 CH1 Report No.: RF900801R02 52 Issued: August 8, 2001

FCC ID: HFS9550015318 CH6 Report No.: RF900801R02 53 Issued: August 8, 2001

FCC ID: HFS9550015318 CH11 Report No.: RF900801R02 54 Issued: August 8, 2001

FCC ID: HFS9550015318 4.6 BAND EDGES MEASUREMENT 4.6.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100KHz Resolution Bandwidth). 4.6.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until ROHDE & SCHWARZ TEST 848926/005 ESMI Dec 28, 2001 RECEIVER 846839/018 HP ATTENUATOR 8496B 3247A18505 Cal. on use HP PLOTTER 7475A 2641V27755 N/A NOTE: 1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.6.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 kHz bandwidth from band edge. The band edges was measured and recorded. Report No.: RF900801R02 55 Issued: August 8, 2001

FCC ID: HFS9550015318 4.6.4 EUT OPERATING CONDITION Same as Item 4.3.5 4.6.5 TEST RESULTS The spectrum plots are attached on the following 2 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). NOTE: The band edge emission plot on the following 2 pages shows 99.5dB delta between carrier maximum power and local maximum emission in restrict band (2.48604GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.6 (Page 33) is 99.5dBuV/m, so the maximum field strength in restrict band is 99.5-50.61=48.89 dBuV/m which is under 54 dBuV/m limit. Report No.: RF900801R02 56 Issued: August 8, 2001

atestoossesar ‘drood coutosonea on yode LVLOEF Res.Bw 100.0 kHz lfldBfJ Vid.Bw 100 kHz Date 06.Aug.‘01 Time 220218 T6.Lvl Ref .LV1 Marker —29.43 dBm CF.Stp 4.000 MHz AF.Att 0 dB 21.50 dBn 2.39944 CHz Unit [dBn] F1 2.40000000000 6Hz D1 —13.50 dBn F2 OFF D2 6.40 dBm % 0FE-Fi OFF 0102 20.00 d8 10.0 0; ~10.0 =20.0 1 ~30.0 ~40.0 ~50.0 ~60.0 =10.0 100c‘aisntny penssl Start Span Center Sweep Stop 2.375 CHz 40 MHz 2.395 GHz 100 ms 2.415 6Hz wroszay

atestoossesar ‘drood coutosonea on yode Res.Bw 100.0 kHZlfld?% 100 kHz Date 06.Aug. ‘01 Time 22: 56: 09 0 ~29.31 dBm CF.Stp 1,000 WHz AF.Att 0 d 21.50 dBn 2.39081 CHz [dBm 2.40000000000 6Hz ~13.60 dBn OFF 5.40 dBn 20.00 d8 85 scocfit o e 100; ‘psntny penssl Stop 2.39444 CHz 2.39944 CHz 2.40444 CHz wroszay

atestoossesar ‘drood coutosonea on yode LVLOEF Res.Bw 100.0 kHz l3dBJ Vid.8w 100 kHz Date 06.Aug. ‘01 Time 22: 28; 48 T6.Ly]l Ref .Lvl Marker ~44.54 dBm CF.Stp 4.000 MHZ AF.Att 0 dB 21 50 dBn 2.48604 GHz Unit [dBm] OFF D1 ~13.93 dBn FE 2.48350000000 6Hz D2 6.07 dBn F2fi OFF 01—02 20.00 d 20.0 $ 10.0 0 ~10.0 ~20.0 6 ~30.0 ~40.0 ~50.0 ~60.0 ~70.0 100c‘aisntny penssl Start Span Center Sweep Stop 2.46 CHz 40 MHz 2.48 GHz 100 ms 2.5 6iz wroszay

LVLOFF , . Res.Bw 100.0 kHz130B) Vid.8w 100 kHz Date 06.Aug.‘01 Time 22: 32; 38 T6.Lvl off Ref.LV1 NMarker ~44.49 dBm CF.Stp 1.000 MHz BF.Att 0_dB 24.50 dBn 2.40474 CHz Unit {dBm] F OFF DL —13.93 dBn F2 2.48350000000 6Hz D2 6.07 dBn F2A OFF D1—D2 20.00 dB 20.0 10.0 0 : ~10.0 ; _ —20.0 : —30.0 41ho ~50.0 revindend a ; barstinty/elpacean ; ~60.0 ; —70.0 & : i — Start Span Center Sweep _ Stop 2.48104 GHz 10 MHz 2.48604 GHz 100 ms 2.49104 6Hz

FCC ID: HFS9550015318 4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is printed antenna. The antenna connector type is UFL. And the maximum Gain of this antenna is only -5dBi. Report No.: RF900801R02 61 Issued: August 8, 2001

FCC ID: HFS9550015318 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF900801R02 62 Issued: August 8, 2001

FCC ID: HFS9550015318 RADIATED EMISSION TEST Report No.: RF900801R02 63 Issued: August 8, 2001

FCC ID: HFS9550015318 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP Germany TUV Rheinland Japan VCCI New Zealand MoC Norway NEMKO R.O.C. BSMI, DGT, CNLA Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Lin Kou EMC Lab: Hsin Chu EMC Lab: Tel: 886-2-26052180 Tel: 886-35-935343 Fax: 886-2-26052943 Fax: 886-35-935342 Lin Kou Safety Lab: Lin Kou RF&Telecom Lab Tel: 886-2-26093195 Tel: 886-3-3270910 Fax: 886-2-26093184 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF900801R02 64 Issued: August 8, 2001


Document Created: 2001-08-13 11:50:04
Document Modified: 2001-08-13 11:50:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC