RF Exposure Report II Appendix II

FCC ID: HFS-P50WB

RF Exposure Info

Download: PDF
FCCID_2281307

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner ifié Service suisse d‘étalonnage Engineering AG pmzo ied Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland "rfi_\\\\\\\\}‘ Swiss Calibration Service uhials Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Auden Certificate No: D2450V2—869_Jun13 CALIBRATION CERTIFICATE Object D2450V2 — SN: 869 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: June 11, 2013 This calibration certificate documents the traceability to national standards, which realize the physicalunits of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical forcalibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 O1—Nov—12 (No. 217—01640) Oct—13 Power sensor HP 8481A US37202783 O1—Nov—12 (No. 217—01640) Oct—13 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—13 (No. 217—01736) Apr—14 Type—N mismatch combination SN: 5047.3 / 06327 04—Apr—13 (No. 217—01739) Apr—14 Reference Probe ESSDV3 SN: 8205 28—Dec—12 (No. ES3—3205_Dec12) Dec—13 DAE4 SN: 601 25—Apr—13 (No. DAE4—601_Apr13) Apr—14 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—11) In house check: Oct—13 RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—11) In house check: Oct—13 Network Analyzer HP 8758E US37390585 $4206 18—Oct—01 (in house check Oct—12) In house check: Oct—13 in Name Function Signature Calibrated by: Leif Klysner Laboratory Technician Approved by: Katia Pokovic Technical Manager Kees Issued: June 11, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2—869_Jun13 Page 1 of 8

Calibration Laboratory of \:\\3/1//, Schweizerischer Kalibrierdienst Schmid & Partner il;:\/E/‘;: Service suisse d‘étalonnage Engineering AG 2zyc Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 5 ///_\\\\\¢ Swiss Calibration Service CFalutabe®® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—869_Jun13 Page 2 of 8

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASY5 V52.8.7 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.8 + 6 % 1.81 mho/m + 6 % Head TSL temperature change during test <0.5 °C gexe #«e SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.6 W/kg SAR for nominal Head TSL parameters normalized to 1W 53.8 Wikg * 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.30 W/kg SAR for nominal Head TSL parameters normalized to 1W 25.0 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 50.9 + 6 % 2.02 mho/m + 6 % Body TSL temperature change during test <0.5 °C _ SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 13.2 Wikg SAR for nominal Body TSL parameters normalized to 1W 51.5 Wikg 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.09 W/kg SAR for nominal Body TSL parameters normalized to 1W 24.0 Wikg + 16.5 % (k=2) Certificate No: D2450V2—869_Jun13 Page 3 of 8

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 54.1 Q + 5.5 jQ Return Loss —23.6 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.4 Q + 6.6 jQ Return Loss —23.6 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.159 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on August 18, 2010 Certificate No: D2450V2—869_Jun13 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 11.06.2013 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 869 Communication System: UID 0 — CW ; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.81 S/m; & =37.8; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: * Probe: ES3DV3 — SN3205; ConvF(4.52, 4.52, 4.52); Calibrated: 28.12.2012; e Sensor—Surface: 3mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 25.04.2013 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 & DASY532 52.8.7(1137); SEMCAD X 14.6.10(7164) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 95.432 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 28.1 W/kg SAR(1 g) = 13.6 W/kg; SAR(10 g) = 6.3 W/kg Maximum value of SAR (measured) = 17.1 W/kg ~4.60 —8.20 —13.00 —18.40 —23.00 0 dB = 17.1 W/kg = 12.33 dBW/kg Certificate No: D2450V2—869_Jun13 Page 5 of 8

Impedance Measurement Plot for Head TSL 11 Jun 2013 @9:43:12 CHI) si1 1 U Fs 4: 54.102 a 5.4863 6 356.40 pH 2450.000 0BD MHz ——r— Av 169 H1d CH2 Ca Av 16" H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—869_Jun13 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 11.06.2013 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 869 Communication System: UID 0 — CW ; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.02 S/m; &, = 50.9; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: e Probe: ES3DV3 — SN3205; ConvF(4.42, 4.42, 4.42); Calibrated: 28.12.2012; e Sensor—Surface: 3mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 25.04.2013 e Phantom: Flat Phantom 5.0 (back); Type: QDOOOPS50OAA; Serial: 1002 e DASY32 52.8.7(1137); SEMCAD X 14.6.10(7164) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 95.432 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 27.6 W/kg SAR(I g) = 13.2 W/kg; SAR(10 g) = 6.09 W/kg Maximum value of SAR (measured) = 17.3 W/kg ~4.60 —8.20 —13.00 —18.40 —23.00 0 dB = 17.3 W/kg = 12.38 dBW/kg Certificate No: D2450V2—869_Jun13 Page 7 of 8

Impedance Measurement Plot for Body TSL 11 Jun 2013 @9:42:40 CHI) sii 1 U FS 11 49.430 a 6.5586 n 426.05 pH 2 450.000 000 MHz Del Ca Av 16 * HLd CH2 Ca Av 16 ® H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—869_Jun13 Page 8 of 8

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client CCS—TW (Auden) Certificate No: D5GHzV2—1004_Nov13 |CALIBRATION CERTIFICATE Object D5GHzV2 — SN: 1004 Calibration procedure(s) QA CAL—22.v2 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: November 28, 2013 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37292783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—13 (No. 217—01736) Apr—14 Type—N mismatch combination SN: 5047.3 / 06327 04—Apr—13 (No. 217—01739) Apr—14 Reference Probe ESSDV3 SN: 3205 28—Dec—12 (No. ES3—3205_Dec12) Dec—13 DAE4 SN: 601 25—Apr—13 (No. DAE4—601_Apr13) Apr—14 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—13) In house check: Oct—14 Name Function CIQ:fire ( Calibrated by: Claudio Leubler Laboratory Technician Approved by: KatJa Pokovic Technical Manager TxAtes Issued: November 28, 2013 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1004_Nov13 Page 1 of 15

Calibration Laboratory of S Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEC 62209—2, "Evaluation of Human Exposure to Radio Frequency Fields from Handheld and Body—Mounted Wireless Communication Devices in the Frequency Range of 30 MHz to 6 GHz: Human models, Instrumentation, and Procedures"; Part 2: "Procedure to determine the Specific Absorption Rate (SAR) for including accessories and multiple transmitters", March 2010 b) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" c) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle!l to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1004_Nov13 Page 2 of 15

Measurement Conditions DASY system configuration, as far as not g iven on page 1. DASY Version DASY5 V52.8.7 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy =4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz +1 MHz 5300 MHz +1 MHz Frequency 5600 MHz +1 MHz 5800 MHz +1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.0 + 6 % 4.46 mho/m + 6 % Head TSL temperature change during test <0.5 °C axec SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.04 W/kg SAR for nominal Head TSL parameters normalized to 1W 79.9 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 W/kg SAR for nominal Head TSL parameters normalized to 1W 22.8 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1004_Nov13 Page 3 of 15

Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.9 +6 % 4.55 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~——— SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.56 W/kg SAR for nominal Head TSL parameters normalized to 1W 85.0 W / kg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.45 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.3 Wikg * 19.5 % (k=2) Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.5 + 6 % 4.85 mho/m + 6 % Head TSL temperature change during test <0.5 °C asse wese SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.48 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.1 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.41 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.9 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1004_Nov13 Page 4 of 15

Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.3 5.27 mho/m Measured Head TSL parameters (22.0 £0.2) °C 34.2 26 % 5.06 mho/m + 6 % Head TSL temperature change during test <0.5 °C seee §# SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.08 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.1 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.29 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1004_Nov13 Page 5 of 15

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.5 6 % 5.44 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.58 W/kg SAR for nominal Body TSL parameters normalized to 1W 75.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.11 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.0 Wikg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47. 4 x 6 % 5.57 mho/m + 6 % Body TSL temperature change during test <0.5 °C —— ———— SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.80 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.6 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.18 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.7 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1004_Nov13 Page 6 of 15

Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.8 +6 % 5.97 mho/m + 6 % Body TSL temperature change during test <0.5 °C #<+: SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.21 W/kg SAR for nominal Body TSL parameters normalized to 1W 81.6 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.27 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.5 Wikg + 19.5 % (k=2) Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.5 + 6 % 6.25 mho/m + 6 % Body TSL temperature change during test <0.5 °C ——— =———— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.61 W/kg SAR for nominal Body TSL parameters normalized to 1W 75.7 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.10 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.8 W/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1004_Nov13 Page 7 of 15

Appendix Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 48.7 Q — 9.3 jQ Return Loss —20.5 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 52.3 Q — 5.4 jQ Return Loss — 24.8 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 53.8 Q — 5.9 jQ Return Loss —23.4 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 58.8 Q — 2.9 jQ Return Loss —21.4 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 50.0 Q — 8.7 jQ Return Loss — 21.3 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 52.6 Q — 4.2 jQ Return Loss —26.4 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.8 Q — 3.4 jQ Return Loss —23.9 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 59.5 Q — 1.1 jQ Return Loss —21.2 dB Certificate No: D5GHzV2—1004_Nov13 Page 8 of 15

General Antenna Parameters and Design Electrical Delay (one direction) 1.152 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on July 08, 2003 Certificate No: D5GHzV2—1004_Nov13 Page 9 of 15

DASY5 Validation Report for Head TSL Date: 22.11.2013 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5SGHzV2; Serial: D5GHzV2 — SN: 1004 Communication System: UID 0 — CW ; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 =4.46 $/m; &, = 35; p = 1000 kg/m‘, Medium parameters used: f = 5300 MHz; 0 = 4.55 S/m; &, = 34.9; p = 1000 kg/m3 ; Medium parameters used: f = 5600 MHz; 0 = 4.85 S/m; &, = 34.5; p = 1000 kg/m3 ; Medium parameters used: f = 5800 MHz; 0 = 5.06 S/m; &, = 34.2; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.41, 5.41, 5.41); Calibrated: 28.12.2012, ConvF(5.1, 5.1, 5.1); Calibrated: 28.12.2012, ConvF(4.76, 4.76, 4.76); Calibrated: 28.12.2012, ConvF(4.81, 4.81, 4.81); Calibrated: 28.12.2012; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 $Sn601; Calibrated: 25.04.2013 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 e DASY52 52.8.7(1137); SEMCAD X 14.6.10(7164) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.762 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(1 g) = 8.04 W/kg; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 18.1 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.388 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 32.5 W/kg SAR(1 g) = 8.56 W/kg; SAR(10 g) = 2.45 W/kg Maximum value of SAR (measured) = 19.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.738 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 33.8 W/kg SAR(1 g) = 8.48 W/kg; SAR(10 g) = 2.41 W/kg Maximum value of SAR (measured) = 19.9 W/kg Certificate No: D5GHzV2—1004_Nov13 Page 10 of 15

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 61.846 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 33.7 W/kg SAR(1 g) = 8.08 W/kg; SAR(10 g) = 2.29 W/kg Maximum value of SAR (measured) = 19.3 W/kg —6.00 12.00 —18.00 —24.00 —30.00 No 0 dB = 19.3 W/kg = 12.86 dBW/kg Certificate No: D5GHzV2—1004_Nov13 Page 11 of 15

Impedance Measurement Plot for Head TSL 22 Nov 2013 15:36:953 CHI sii 1 U FS 1:48.608 a —9.3105 n 9.2873 pF 5 200.000 000 MHz stk. CH1 Markers Del 2: 52.316 o ~5.4479 a Cor 5.30000 GHz 4 53.799 a —5.9595 a 5.60000 GHz 5: 58.789 8935 a Av 5.90000 GHz 168 H1d CH2 Del CH2 Markers Cor 2:~24.758 dB 5.30000 GHz 4:—23.368 dB 5.60000 GHz :—21,426 dB Av 5.80000 GHz 16 ® H1d START 5 000.000 000 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1004_Nov13 Page 12 of 15

DASY5 Validation Report for Body TSL Date: 28.11.2013 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5SGHzV2; Serial: D5GHzV2 — SN: 1004 Communication System: UID 0 — CW ; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: £ = 5200 MHz; 0 = 5.44 S/m; &, = 47.5; p = 1000 kg/m3 s Medium parameters used: £ = 5300 MHz; 0 = 5.57 S/m; & = 47.4; p = 1000 kg/m3 g Medium parameters used: £ = 5600 MHz; 0 = 5.97 $/m; &, = 46.8; p = 1000 kg/m3 ; Medium parameters used: £= 5800 MHz; 0 = 6.25 $/m; &, = 46.5; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI €63.19—2007) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(4.91, 4.91, 4.91); Calibrated: 28.12.2012, ConvF(4.67, 4.67, 4.67);, Calibrated: 28.12.2012, ConvF(4.22, 4.22, 4.22); Calibrated: 28.12.2012, ConvF(4.38, 4.38, 4.38); Calibrated: 28.12.2012; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 $Sn601; Calibrated: 25.04.2013 * Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50OAA; Serial: 1002 «_ DASY52 52.8.7(1137); SEMCAD X 14.6.10(7164) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.803 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) =30.1 W/kg SAR(1 g) = 7.58 W/kg; SAR(10 g) = 2.11 W/kg Maximum value of SAR (measured) = 17.8 W/kg Dipole Calibration for Body Tissue/Pin=100mwW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.901 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 32.0 W/kg SAR(I g) =7.8 W/kg; SAR(10 g) = 2.18 W/kg Maximum value of SAR (measured) = 18.5 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.438 V/m; Power Drift =0.01 dB Peak SAR (extrapolated) = 36.7 W/kg SAR(1 g) = 8.21 W/kg; SAR(10 g) = 2.27 W/kg Maximum value of SAR (measured) = 20.0 W/kg Certificate No: D5GHzV2—1004_Nov13 Page 13 of 15

Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 56.082 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 35.8 W/kg SAR(I g) = 7.61 W/kg; SAR(10 g) = 2.1 W/kg Maximum value of SAR (measured) = 18.9 W/kg —5.00 —10.00 15.00 —20.00 —25.00 0 dB = 18.9 W/kg = 12.76 dBW/kg Certificate No: D5GHzV2—1004_Nov13 Page 14 of 15

Impedance Measurement Plot for Body TSL 28 Nov 2013 11:12:06 CHI) sii 1 U Fs 1: 50.039 a —8.67970 3.5262 pF 5 200.000 000 MHz # CH1 Markers Del 2: 52.613 a ~4.1650 a Cor 5.30000 GHz 3 55.811 a —3.3867 a 5.60000 GHz 9.533 o Ag 6566 a 16 5.90000 GHz H1d CH2 CH2 Markers Cor 2—26,388 dB 5.30000 GHz 3:—23.936 dB 5.60000 GHz 41—21,152 dB fts 5.90000 GHz 16 H1d START 5 000.000 008 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1004_Nov13 Page 15 of 15


Document Created: 2014-05-26 13:41:57
Document Modified: 2014-05-26 13:41:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC