Test Report Revised

FCC ID: HFS-HA1

Test Report

Download: PDF
FCCID_477414

FCC ID: HFS-HA1 FCC TEST REPORT REPORT NO.: RF930701L11 MODEL NO.: IBF-005 (for other model names please refer to page 5) RECEIVED: July 01, 2004 TESTED: July 01, 2004 ~ July 15, 2004 APPLICANT: QUANTA COMPUTER INC. ADDRESS: 7F, 116, Hou Kang St., Shih Lin, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 33 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA Report No.: RF930701L11 1 Issued: July 20, 2004.

FCC ID: HFS-HA1 Table of Contents 1 CERTIFICATION ..................................................................................... 3 2 SUMMARY OF TEST RESULTS ............................................................. 4 2.1 MEASUREMENT UNCERTAINTY ........................................................... 4 3. GENERAL INFORMATION...................................................................... 5 3.1 GENERAL DESCRIPTION OF EUT ........................................................ 5 3.2 DESCRIPTION OF TEST MODES .......................................................... 6 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ......................... 6 3.4 DESCRIPTION OF SUPPORT UNITS .................................................... 7 3.5 CONFIGURATION OF SYSTEM UNDER TEST ..................................... 8 4. TEST TYPES AND RESULTS ................................................................. 9 4.1 CONDUCTED EMISSION MEASUREMENT .......................................... 9 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................ 9 4.1.2 TEST INSTRUMENTS............................................................................. 9 4.1.3 TEST PROCEDURES ........................................................................... 10 4.1.4 DEVIATION FROM TEST STANDARD ................................................. 10 4.1.5 TEST SETUP ........................................................................................ 11 4.1.6 EUT OPERATING CONDITIONS ......................................................... 11 4.1.7 TEST RESULTS ..................................................................................... 12 4.2 RADIATED EMISSION MEASUREMENT ............................................. 18 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT........................... 18 4.2.2 TEST INSTRUMENTS........................................................................... 19 4.2.3 TEST PROCEDURES ........................................................................... 20 4.2.4 DEVIATION FROM TEST STANDARD ................................................. 20 4.2.5 TEST SETUP ........................................................................................ 21 4.2.6 EUT OPERATING CONDITIONS .......................................................... 21 4.2.7 TEST RESULTS .................................................................................... 22 4.3 BAND EDGES MEASUREMENT .......................................................... 27 4.3.1 LIMITS OF BAND EDGES MEASUREMENT........................................ 27 4.3.2 TEST INSTRUMENTS........................................................................... 27 4.3.3 TEST PROCEDURE ............................................................................. 27 4.3.4 EUT OPERATING CONDITION ............................................................ 27 4.3.5 TEST RESULTS .................................................................................... 28 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ............................ 31 6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES ....... 33 Report No.: RF930701L11 2 Issued: July 20, 2004.

FCC ID: HFS-HA1 1 CERTIFICATION PRODUCT : Flipscreen MODEL NO.: IBF-005 (for other model names please refer to page 5) BRAND: Quanta APPLICANT : QUANTA COMPUTER INC. TEST ITEM: ENGINEERING SAMPLE TESTED: July 01 ~ July 19, 2004 STANDARDS : FCC Part 15, Subpart C (Section 15.249), ANSI C63.4-2001 The above equipment has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY: , DATE: July 20, 2004 Stacy Hsueh APPROVED BY: , DATE: July 20, 2004 Cody Chang / Supervisor Report No.: RF930701L11 3 Issued: July 20, 2004.

FCC ID: HFS—HA1 ILD?" apr corm 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C STANDARD PARAGRAPH TEST TYPE RESULT REMARK Minimum passing 15.207 Conducted Emission Test PASS |margin is —22.19dB at 0.213MHz 15.209 Minimum passing 15'249 Radiated Emission Test PASS |margin is —6.75dB at ' 1810.71MHz 15.249 (d) |Band Edge Measurement Pass ('\)’L‘Tliitthe requirement Note: The information of measurement uncertainty is available upon the customer‘s request. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16—4: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions Ok~3OMHz 2.44 dB Radiated emissions 30MHz ~ 200MHz 3.63 dB 200MHz ~1000MHz 3.65 dB 1GHz ~18GHz 2.20 dB 18GHz ~40GHz 1.88 dB Report No.: RFORO7O1L11 4 Issued: July 20, 2004

FCC ID: HFS-HA1 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT Flipscreen IBF-005 MODEL NO. (for other model names please refer to following table) BRAND Quanta POWER SUPPLY 3.0Vdc from host equipment MODULATION TYPE FSK CARRIER FREQUENCY OF 905.609756 ~ 924.390244MHz EACH CHANNEL NUMBER OF CHANNEL 28 ANTENNA TYPE Dipole antenna with –2dBi gain DATA CABLE NA I/O PORTS NA ASSOCIATED DEVICES NA NOTE: 1. The model as below are identical to each other except for their model due to marketing requirement. Item Model 1 IBF-003 2. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF930701L11 5 Issued: July 20, 2004.

FCC ID: HFS-HA1 3.2 DESCRIPTION OF TEST MODES Twenty- eight channels are provided in the EUT Channel Freq. (MHz) Channel Freq. (MHz) 0 905.609756 14 915.609756 1 908.095238 15 918.095238 2 908.780488 16 918.780488 3 908.888889 17 918.888889 4 908.918919 18 918.918919 5 909.705882 19 919.705882 6 909.736842 20 919.736842 7 910.263158 21 920.236158 8 910.294118 22 920.294118 9 911.081081 23 921.081081 10 911.111111 24 921.111111 11 911.219512 25 921.219512 12 911.904762 26 921.904762 13 914.390244 27 924.390244 NOTE: 1. Below 1000MHz, the channel 0, 14, 27 were pre-tested in chamber. The channel 28,worst case one, was chosen for final test. 2. Above 1000MHz, the channel 0, 14, 27 were tested individually. 3. The EUT was tested under transmit simultanous with the support unit of IEEE 802.11b wireless card, Model no:C110. 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a Flipscreen. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C. (15.249) ANSI C63.4-2001 All test items have been performed and recorded as per the above standards. Report No.: RF930701L11 6 Issued: July 20, 2004.

FCC ID: HFS-HA1 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID WIRELESS 1 ICEBOX 30034 401033660 FCC DoC Approved KEYBOARD (IrDa) REMOTE 2 ICEBOX 30033 306800158 FCC DoC Approved CONTROL (IrDa) 3 SANI CARD Beyond RFT-LS-B-US 031100000796 RTN-BCC-RFMV04 802.11b PCMCIA 4 Tellus C110 0000800F PB6-03111 CARD NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 NA 2 NA 3 NA 4 NA NOTE: 1. All power cords of the above support units are non shielded (1.8m). 2. The PCMCIA and SANI cards are actually in operation during the testing. . Report No.: RF930701L11 7 Issued: July 20, 2004.

FCC ID: HFS-HA1 3.5 CONFIGURATION OF SYSTEM UNDER TEST EUT SANI CARD PCMCIA CARD Keyboard Remote Wireless Control Report No.: RF930701L11 8 Issued: July 20, 2004.

FCC ID: HFS-HA1 4. TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15-0.5 66 to 56 56 to 46 0.5-5 56 46 5-30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.1.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. CALIBRATED UNTIL Test Receiver ESCS30 100291 Dec. 12, 2004 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-HYC01-01 Mar. 02, 2005 Woken LISN ESH3-Z5 847265/023 Oct. 22, 2004 ROHDE & SCHWARZ LISN ESH3-Z5 100220 Dec. 10, 2004 ROHDE & SCHWARZ Software ADT_Cond_V3 NA NA ADT NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040.Hwa Ya Global Certification Office Report No.: RF930701L11 9 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under Limit –20dB was not recorded. 4.1.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF930701L11 10 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.1.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.1.6 EUT OPERATING CONDITIONS a. Placed the EUT on a testing table. b. The EUT ran a test program to enable all functions under transmission/receiving condition continuously at specific channel frequency. c. The EUT sent "H" messages to its screen. Report No.: RF930701L11 11 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.1.7 TEST RESULTS EUT Flipscreen MODEL IBF-005 MODE Channel 0 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Line (L) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.213 0.12 40.80 - 40.92 - 63.11 53.11 -22.19 - 2 0.435 0.13 31.68 - 31.81 - 57.15 47.15 -25.35 - 3 0.654 0.13 26.99 - 27.12 - 56.00 46.00 -28.88 - 4 2.809 0.18 22.41 - 22.59 - 56.00 46.00 -33.41 - 5 4.148 0.21 30.53 - 30.74 - 56.00 46.00 -25.26 - 6 13.777 0.66 17.90 - 18.56 - 60.00 50.00 -41.44 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 12 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 MODE Channel 0 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Neutral (N) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.213 0.11 39.78 - 39.89 - 63.11 53.11 -23.22 - 2 0.435 0.12 32.28 - 32.40 - 57.15 47.15 -24.76 - 3 0.873 0.14 24.63 - 24.77 - 56.00 46.00 -31.23 - 4 1.313 0.15 24.26 - 24.41 - 56.00 46.00 -31.59 - 5 4.133 0.20 28.55 - 28.75 - 56.00 46.00 -27.25 - 6 14.099 0.58 18.98 - 19.56 - 60.00 50.00 -40.44 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 13 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 MODE Channel 14 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Line (L) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.213 0.12 40.10 - 40.22 - 63.11 53.11 -22.89 - 2 0.326 0.12 33.97 - 34.09 - 59.56 49.56 -25.46 - 3 0.709 0.14 29.74 - 29.88 - 56.00 46.00 -26.12 - 4 4.086 0.21 29.36 - 29.57 - 56.00 46.00 -26.43 - 5 6.266 0.27 16.86 - 17.13 - 60.00 50.00 -42.87 - 6 17.844 0.92 26.25 - 27.17 - 60.00 50.00 -32.83 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 14 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 MODE Channel 14 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Neutral (N) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.213 0.11 40.40 - 40.51 - 63.11 53.11 -22.60 - 2 0.435 0.12 32.62 - 32.74 - 57.15 47.15 -24.42 - 3 0.709 0.13 29.36 - 29.49 - 56.00 46.00 -26.51 - 4 3.250 0.19 27.68 - 27.87 - 56.00 46.00 -28.13 - 5 6.141 0.25 18.52 - 18.77 - 60.00 50.00 -41.23 - 6 14.191 0.58 26.15 - 26.73 - 60.00 50.00 -33.27 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 15 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 MODE Channel 27 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Line (L) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.216 0.12 38.94 - 39.06 - 62.96 52.96 -23.90 - 2 0.435 0.13 32.76 - 32.89 - 57.15 47.15 -24.27 - 3 1.309 0.15 25.59 - 25.74 - 56.00 46.00 -30.26 - 4 4.090 0.21 27.66 - 27.87 - 56.00 46.00 -28.13 - 5 17.855 0.92 26.05 - 26.97 - 60.00 50.00 -33.03 - 6 22.883 1.10 29.72 - 30.82 - 60.00 50.00 -29.18 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 16 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 MODE Channel 27 6dB BANDWIDTH 9kHz INPUT POWER 120Vac, 60 Hz PHASE Neutral (N) (SYSTEM) ENVIRONMENTAL 24deg. C, 64%RH, TESTED BY: Leo Hung CONDITIONS 991hPa Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.213 0.11 40.58 - 40.69 - 63.11 53.11 -22.42 - 2 0.435 0.12 32.76 - 32.88 - 57.15 47.15 -24.28 - 3 1.309 0.15 25.55 - 25.70 - 56.00 46.00 -30.30 - 4 2.680 0.17 25.26 - 25.43 - 56.00 46.00 -30.57 - 5 4.098 0.20 30.56 - 30.76 - 56.00 46.00 -25.24 - 6 15.555 0.65 27.75 - 28.40 - 60.00 50.00 -31.60 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: RF930701L11 17 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT The field strength of emission from fundamental frequency shall comply with the followng: Frequencies Field strength (dBuV/m) (MHz) Peak Average 902 ~ 928 114 94 Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF930701L11 18 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.2.2 TEST INSTRUMENTS . DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL Test Receiver ESI7 838496/016 Feb. 09, 2005 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100041 Dec. 15, 2004 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-155 Feb. 03, 2005 SCHWARZBECK HORN Antenna BBHA 9120D 9120D-404 Feb. 03, 2005 SCHWARZBECK HORN Antenna BBHA 9170 BBHA 9170242 Feb. 23, 2005 SCHWARZBECK Preamplifier 8447D 2944A10631 Jan. 15, 2005 Agilent Preamplifier 8449B 3008A01960 Jan. 22, 2005 Agilent RF signal cable SUCOFLEX 104 219272/4 Mar. 04, 2005 HUBER+SUHNNER RF signal cable SUCOFLEX 104 219275/4 Mar. 04, 2005 HUBER+SUHNNER Software ADT_Radiated_V5.14 NA NA ADT. Antenna Tower MA 4000 010303 NA inn-co GmbH Antenna Tower Controller CO2000 019303 NA inn-co GmbH Turn Table TT100. TT93021704 NA ADT. Turn Table Controller SC100. SC93021704 NA ADT. NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 3. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The IC Site Registration No. is IC4924-4. Report No.: RF930701L11 19 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anchoic. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-tested one by one using the quasi-peak method or average method as specified and then reported in Data sheet peak mode and QP mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. 4.2.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF930701L11 20 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.2.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.2.6 EUT OPERATING CONDITIONS Same as item 4.1.6 Report No.: RF930701L11 21 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.2.7 TEST RESULTS EUT Flipscreen MODEL IBF-005 CHANNEL Channel 0 DETECTOR Peak (PK) INPUT POWER FUNCTION Average (AV) 120Vac, 60 Hz (SYSTEM) ENVIRONMENTAL 28deg. C, 55%RH, TESTED BY Allen Chang CONDITIONS 991hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *905.36 83.02 PK 94.00 -10.98 1.37 H 62 58.15 24.87 2 1810.71 56.53 PK 74.00 -17.47 1.07 H 343 26.00 30.53 3 1810.71 47.25 AV 54.00 -6.75 1.07 H 343 16.72 30.53 4 2716.10 54.25 PK 74.00 -19.75 1.12 H 331 19.32 34.93 5 2716.10 44.97 AV 54.00 -9.03 1.12 H 331 10.04 34.93 6 4526.97 53.30 PK 74.00 -20.70 1.15 H 352 13.40 39.89 7 4526.97 44.02 AV 54.00 -9.98 1.15 H 352 4.13 39.89 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *905.36 76.77 PK 94.00 -17.23 1.43 V 72 51.90 24.87 2 1810.70 50.83 PK 74.00 -23.17 1.03 V 243 20.30 30.53 3 1810.70 41.55 AV 54.00 -12.45 1.03 V 243 11.02 30.53 4 2716.09 53.68 PK 74.00 -20.32 1.00 V 334 18.75 34.93 5 2716.09 44.40 AV 54.00 -9.60 1.00 V 334 9.47 34.93 6 4525.67 51.38 PK 74.00 -22.62 1.00 V 313 11.49 39.89 7 4525.67 42.10 AV 54.00 -11.90 1.00 V 313 2.21 39.89 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB) = Antenna Factor (dB) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “*” = Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 33.386774ms 20log(Duty cycle) = 20log =-9.53dB 100ms please see page 25-26for plotted duty Report No.: RF930701L11 22 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 CHANNEL Channel 14 DETECTOR Peak (PK) INPUT POWER FUNCTION Average (AV) 120Vac, 60 Hz (SYSTEM) ENVIRONMENTAL 28deg. C, 55%RH, TESTED BY Allen Chang CONDITIONS 991hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *915.14 81.42 PK 94.00 -12.58 1.34 H 62 56.45 24.97 2 1830.70 53.63 PK 74.00 -20.37 1.00 H 346 22.95 30.68 3 1830.70 44.10 AV 54.00 -9.90 1.00 H 346 13.42 30.68 4 2746.15 53.20 PK 74.00 -20.80 1.32 H 333 18.20 35.00 5 2746.15 43.67 AV 54.00 -10.33 1.32 H 333 8.67 35.00 6 4576.88 51.71 PK 74.00 -22.29 1.04 H 351 11.78 39.93 7 4576.88 42.18 AV 54.00 -11.82 1.04 H 351 2.25 39.93 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *915.14 77.24 PK 94.00 -16.76 1.46 V 110 52.27 24.97 2 1830.23 48.88 PK 74.00 -25.12 1.00 V 243 18.20 30.67 3 1830.23 39.35 AV 54.00 -14.65 1.00 V 243 8.68 30.67 4 2746.04 51.32 PK 74.00 -22.68 1.00 V 10 16.32 35.00 5 2746.04 41.79 AV 54.00 -12.21 1.00 V 10 6.79 35.00 6 4576.88 51.98 PK 74.00 -22.02 1.08 V 322 12.05 39.93 7 4576.88 42.45 AV 54.00 -11.55 1.08 V 322 2.52 39.93 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB) = Antenna Factor (dB) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “*” = Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 33.386774ms 20log(Duty cycle) = 20log =-9.53dB 100ms please see page 25-26for plotted duty Report No.: RF930701L11 23 Issued: July 20, 2004.

FCC ID: HFS-HA1 EUT Flipscreen MODEL IBF-005 CHANNEL Channel 27 DETECTOR Peak (PK) INPUT POWER FUNCTION Average (AV) 120Vac, 60 Hz (SYSTEM) ENVIRONMENTAL 28deg. C, 55%RH, TESTED BY Allen Chang CONDITIONS 991hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *924.84 80.58 PK 94.00 -13.42 1.31 H 53 55.51 25.07 2 1849.70 49.41 PK 74.00 -24.59 1.00 H 22 18.59 30.82 3 1849.70 39.88 AV 54.00 -14.12 1.00 H 22 9.06 30.82 4 2773.86 51.55 PK 74.00 -22.45 1.07 H 354 16.48 35.07 5 2773.86 42.02 AV 54.00 -11.98 1.07 H 354 6.95 35.07 6 4623.16 51.71 PK 74.00 -22.29 1.00 H 6 11.71 40.01 7 4623.16 42.18 AV 54.00 -11.82 1.00 H 6 2.17 40.01 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *924.84 77.29 PK 94.00 -16.71 1.44 V 212 52.22 25.07 2 1849.30 50.80 PK 74.00 -23.20 1.29 V 87 19.99 30.81 3 1849.30 41.27 AV 54.00 -12.73 1.29 V 87 10.46 30.81 4 2774.51 49.59 PK 74.00 -24.41 1.00 V 338 14.52 35.07 5 2774.51 40.06 AV 54.00 -13.94 1.00 V 338 4.99 35.07 6 4623.17 51.42 PK 74.00 -22.58 1.38 V 303 11.42 40.01 7 4623.17 41.89 AV 54.00 -12.11 1.38 V 303 1.88 40.01 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB) = Antenna Factor (dB) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “*” = Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 33.386774ms 20log(Duty cycle) = 20log =-9.53dB 100ms please see page 25-26 for plotted duty Report No.: RF930701L11 24 Issued: July 20, 2004.

LVH—S4H ‘UI 004 LL110z0ge4y yon uodey Delta 1 [LT1] RBW 100 kHz RF Aftt 30 cdBd B rer Lo: —0 .01 dB VBHW 1080 kHz 20.5 dBm 151.903808 ms SWT 200 ms Unit dBm 20 .5 _ 0 .5 dB Offse 10 SGL —10 1MA —20 SC —30 —40 ooz ‘oz Ainp :penssq —70 —79.5 Center 905.1292585 MHz 20 ms,/

LL1L0z08e4 yon uodex LYH—S4H ‘UI 004 Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref LvI 0.38 dB VBH 100 kHz 20.5 dBm 33.386774 ms SWT 56 ms Undit dBm 20.5 rnmmemmmmmnmenmnmnn mmmnremmmmmmmen 0.5 dB Offset 10 SGL D [ C —10 1MAX 1MA —280 ]_ 97 —30 F —40 ~50 —60 Adfy U "Fooz ‘oz Ainp :;penssq —70 H4OD 10V af/ KCCV —79.5 +— Center 905.1292585 MHz 5.6 ms»~

FCC ID: HFS-HA1 4.3 BAND EDGES MEASUREMENT 4.3.1 LIMITS OF BAND EDGES MEASUREMENT Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in § 15.209, whichever is the lesser attenuation. 4.3.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 August 12, 2004 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. 4.3.4 EUT OPERATING CONDITION Enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF930701L11 27 Issued: July 20, 2004.

FCC ID: HFS-HA1 4.3.5 TEST RESULTS The spectrum plots are attached on the following 2 pages. D2 line indicates the highest level, D1 line indicates the 50dB offset below D2. It shows compliance with the requirement in part 15.249(d). NOTE1: The band edge emission plot on the following first page shows 62.91dB delta between carrier maximum power and local maximum emission in restrict band (898.1924MHz). The emission of carrier strength list in the test result of channel 0 at the item 4.2.7 is 83.02dBuV/m, so the maximum field strength in restrict band is 83.02-62.91=20.11dBuV/m which is under 54dBuV/m limit. NOTE2: The band edge emission plot on the following second page shows 59.90dB delta between carrier maximum power and local maximum emission in restrict band (945.4349MHz). The emission of carrier strength list in the test result of channel 27 at the item 4.2.7 is 80.58dBuV/m, so the maximum field strength in restrict band is 80.58-59.90=20.68dBuV/m which is under 54dBuV/m limit. Report No.: RF930701L11 28 Issued: July 20, 2004.

LL7L0z08e—43 on uodex LYH—S4H ‘Ual 004 Marker 1 [T1] RBHW 100 kHz RF Att 30 dB Ref LvI 4.16 dBm VBH 100 kHz 20.5 dBm 905. 19238477 MHz SWT 25 ms Unit dBm 20.5 ommmemmes momenenmemne a 0.5 dB Offse}f 1l1Ti] 4.16 cBm 905 . 192384 7]7 MHz 10 "24——5 =68—78—dBm —D1 4.1G6 dBm 902.00000000 Hz a Y3 |[T1] —5§. 76 gBam 898 . 192394717 WHz —10 1VIEW 1MA —20 62 —30 ~40 |——D2 |—45.84 Bm —50 Fooz ‘oz Ainp :penss| —70 4O> 10V Fi —79.51 Center 859 MHz 10 MHzz/ Span 100 I MHz >

LL7L0Z0E6I¥ ~on uodey LYVH—S4H ‘dI D04 p Marker 1 [T1il 100 kHz RF Att 30 dB TR Ref Lv l 4.15 dBm 100 kHz 20 .5 dBm 924.73202405 MHz 25 ms Lin it dBm 20.59 0.5 dB Offse Yi lTcTid 4. 15 dBm 9944 .73207405 MHz 10 & 545 =SS—++—dBm ons 4. k sss sds . 00000000 mHz £ v3 £Ti] —593.75 dBm 945 .43480974 MHz —10 1v1gw 1MA —20 O€ —30 —40 P2||—4s.s5 HBm —5s0 3 —60 A *wxwlbkfih¢,d4*duamqfixanwnukm4;uufl+44¢*LAJJ;LflJeHNHJVaunhufi —70 "FOo? ‘0¢ Ainp :penssq F F2— HH%\/ —79.5 [ \/ Center Y68.72 MHz 10 MHzz Span 100 MHz

FCC ID: HFS-HA1 5. PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF930701L11 31 Issued: July 20, 2004.

FCC ID: HFS-HA1 RADIATED EMISSION TEST Report No.: RF930701L11 32 Issued: July 20, 2004.

FCC ID: HFS-HA1 6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP, UL Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, DGT Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Linko RF Lab. Tel: 886-3-3183232 Tel: 886-3-3270910 Fax: 886-3-3185050 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report Format Version 1.0 Report No.: RF930701L11 33 Issued: July 20, 2004.


Document Created: 2004-08-05 16:07:33
Document Modified: 2004-08-05 16:07:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC