RF exposure calculation

FCC ID: HEDSMC2552WG

RF Exposure Info

Download: PDF
FCCID_396454

FCC ID: HEDSMC2552WG RF EXPOSURE REPORT REPORT NO.: RF920619H03E MODEL NO.: SMC2552W-G ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Accton Technology Corporation ADDRESS: No.1, Creation Rd. III, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. Lab Code: 200376-0 ADT No.: 921106H04 1

FCC ID: HEDSMC2552WG RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Electric Field Magnetic Field Power Density Average Time Range Strength (V/m) Strength (A/m) (mW/cm2) (minutes) (MHz) (A)Limits For Occupational / Control Exposures 300-1500 … … F/300 6 1500-100,000 … … 5 6 (B)Limits For General Population / Uncontrolled Exposure 300-1500 … … F/1500 6 1500-100,000 … … 1.0 30 F = Frequency in MHz ADT No.: 921106H04 2

FCC ID: HEDSMC2552WG 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm2. If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification This device is not fixed inside the host equipment, it is connected with host through wire. So it is easy to be re-located in the place where at least 20 cm far away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device. ADT No.: 921106H04 3

FCC ID: HEDSMC2552WG 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber are 2.71Bi or 1.87 (numeric). 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: For DSSS: Channel Limit of Output Power to Power Density Channel Frequency Power Density Antenna (mW) (mW/cm2) (MHz) (mW/cm2) 1 2412 32.21 0.0120 1.0 6 2437 55.72 0.0207 1.0 11 2462 33.57 0.0125 1.0 For OFDM: Channel Limit of Output Power to Power Density Channel Frequency Power Density Antenna (mW) (mW/cm2) (MHz) (mW/cm2) 1 2412 52.48 0.0195 1.0 6 2437 114.28 0.0424 1.0 11 2462 43.65 0.0162 1.0 ADT No.: 921106H04 4


Document Created: 2004-01-06 18:17:52
Document Modified: 2004-01-06 18:17:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC