User manual rev3.pdf

FCC ID: HD5-HONST60

Users Manual

Download: PDF
FCCID_4361806

HON-ST60 Wi-Fi Module Installation Instructions

Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part ofHII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selec- tion and use of software and/or hardware to achieve intended results. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this doc- ument may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright  2000-2018 Honeywell International Inc. All rights reserved. Web Address: www.honeywellaidc.com Other product names or marks mentioned in this document may be trademarks or registered trademarks of other compa- nies and are the property of their respective owners. For patent information, refer to www.hsmpats.com.

What You Get What You Need • A #T10 and a #T20 Torx screwdriver • A small Phillips screwdriver • A small wrench To install the 802.11 interface, you need to open the printer and physically install the interface board in the printer. This interface kit must only be installed by an authorized service technician. The device is country/region specific and must be ordered for the correct country/region. Use of this device in other region than shown on the device home page/test label may violate applicable law. Follow standard ESD guidelines to avoid damaging the equipment you are servicing. Before you begin, turn off the printer and disconnect the power cord and communication cables. The electronic compartment contains wires and components with dangerous voltage (up to 380 V). Make sure that the printer is switched off and the power cord is disconnected before the cover is removed.

Opening the Printer 1. Use a #T10 Torx screwdriver to remove the eight screws that secure the electronics cover. 2. Put the cover aside on a soft cloth to avoid scratches. 3. Insert the antenna cable into the antenna cable jack on the Wi-fi board. 4. Secure the antenna cable to the Wi-fi board with a cable tie. Note the location of the head of the cable tie. 5. Trim the excess from the cable tie. 6. Insert the Wi-fi board into the 44-pin connector.

7. Install the other end of the antenna cable on the back plate and tighten the nut. 8. Use the other cable tie to secure the antenna cable to the printer as shown. 9. Trim the excess from the cable tie. 10. Close the printer. 11. Connect the antenna to the antenna connector on the back plate.

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is radiator & your body. If the module is installed in a portable host, a subject to the following two conditions: (1) This device may not cause separate SAR evaluation is required to confirm compliance with harmful interference, and (2) this device must accept any interference relevant FCC portable RF exposure rules. received, including interference that may cause undesired operation. 2.7 Antennas This equipment has been tested and found to comply with the limits for The following antennas have been certified for use with this module; a Class B digital device, pursuant to Part 15 of the FCC Rules. These antennas of the same type with equal or lower gain may also be used limits are designed to provide reasonable protection against harmful with this module. The antenna must be installed such that 20 cm can be interference in a residential installation. This equipment generates, maintained between the antenna and users. uses and can radiate radio frequency energy and, if not installed and Antenna manufacturer / model Laird MAF94367 used in accordance with the instructions, may cause harmful Antenna Type Dipole Antenna interference to radio communications. However, there is no guarantee Antenna connector R-TNC that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television 2.8 Label and compliance information reception, which can be determined by turning the equipment off and The final end product must be labeled in a visible area with the on, the user is encouraged to try to correct the interference by one of following: “Contains FCC ID: HD5-HONST60”. The grantee's FCC the following measures: ID can be used only when all FCC compliance requirements are met. - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. 2.9 Information on test modes and additional testing requirements - Connect the equipment into an outlet on a circuit different from that This transmitter is tested in a standalone mobile RF exposure condition to which the receiver is connected. and any co-located or simultaneous transmission with other - Consult the dealer or an experienced radio/TV technician for help. transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority 2.10 Additional testing, Part 15 Subpart B disclaimer to operate this equipment. This transmitter module is tested as a subsystem and its certification This transmitter must not be co-located or operating in conjunction does not cover the FCC Part 15 Subpart B (unintentional radiator) rule with any other antenna or transmitter. requirement applicable to the final host. The final host will still need to This device meets all the other requirements specified in Part 15E, be reassessed for compliance to this portion of rule requirements if Section 15.407 of the FCC Rules. applicable. Radiation Exposure Statement: As long as all conditions above are met, further transmitter test will not This equipment complies with FCC radiation exposure limits set forth be required. However, the OEM integrator is still responsible for for an uncontrolled environment. This equipment should be installed testing their end-product for any additional compliance requirements and operated with minimum distance 20cm between the radiator & required with this module installed. your body. IMPORTANT NOTE: In the event that these conditions cannot be This module is intended for OEM integrators only. Per FCC KDB met (for example certain laptop configurations or co-location with 996369 D03 OEM Manual v01 guidance, the following conditions another transmitter), then the FCC authorization is no longer must be strictly followed when using this certified module: considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re- KDB 996369 D03 OEM Manual v01 rule sections: evaluating the end product (including the transmitter) and obtaining a 2.2 List of applicable FCC rules separate FCC authorization. This module has been tested for compliance to FCC Part 15. Manual Information To the End User 2.3 Summarize the specific operational use conditions The OEM integrator has to be aware not to provide information to the The module is tested for standalone mobile RF exposure use condition. end user regarding how to install or remove this RF module in the Any other usage conditions such as co-location with other user’s manual of the end product which integrates this module. The transmitter(s) or being used in a portable condition will need a separate end user manual shall include all required regulatory reassessment through a class II permissive change application or new information/warning as show in this manual. certification. OEM/Host manufacturer responsibilities 2.4 Limited module procedures OEM/Host manufacturers are ultimately responsible for the Not applicable. compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such 2.5 Trace antenna designs as FCC Part 15 Subpart B before it can be placed on the US market. Not applicable. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This 2.6 RF exposure considerations module must not be incorporated into any other device or system This equipment complies with FCC mobile radiation exposure limits without retesting for compliance as multi-radio and combined set forth for an uncontrolled environment. This equipment should be equipment. installed and operated with a minimum distance of 20cm between the

Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to Manuel d'information à l'utilisateur final the following two conditions: (1) This device may not cause harmful L'intégrateur OEM doit être conscient de ne pas fournir des informations à interference, and (2) this device must accept any interference received, l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans including interference that may cause undesired operation. le manuel de l'utilisateur du produit final qui intègre ce module. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils Le manuel de l'utilisateur final doit inclure toutes les informations radio exempts de licence. L’exploitation est autorisée aux deux conditions réglementaires requises et avertissements comme indiqué dans ce manuel. suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage Caution : susceptible de provoquer un fonctionnement indésirable. (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite Radiation Exposure Statement: systems; This equipment complies with ISED radiation exposure limits set forth for an (ii) for devices with detachable antenna(s), the maximum antenna gain uncontrolled environment. This equipment should be installed and operated permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall with greater than 20cm between the radiator & your body. be such that the equipment still complies with the e.i.r.p. limit; (iii) for devices with detachable antenna(s), the maximum antenna gain Déclaration d'exposition aux radiations: permitted for devices in the band 5725-5850 MHz shall be such that Cet équipement est conforme aux limites d'exposition aux rayonnements ISED the equipment still complies with the e.i.r.p. limits as appropriate; établies pour un environnement non contrôlé. Cet équipement doit être installé (iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt et utilisé à plus de 20 cm entre le radiateur et votre corps. angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. This device is intended only for OEM integrators under the following conditions: Avertissement: The antenna must be installed and operated with greater than 20cm between the Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des antenna and users, and instructions précises sur les restrictions susmentionnées, notamment : 2) The transmitter module may not be co-located with any other transmitter or (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés antenna. uniquement pour une utilisation à l’intérieur afin de réduire les risques de As long as 2 conditions above are met, further transmitter test will not be brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes required. However, the OEM integrator is still responsible for testing their end- canaux; product for any additional compliance requirements required with this module (ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne installed. permis pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e; Cet appareil est conçu uniquement pour les intégrateurs OEM dans les (iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne conditions suivantes: permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être L'antenne doit être installé et exploité avec plus de 20 cm entre l'antenne et les conforme à la limite de la p.i.r.e. spécifiée, selon le cas; utilisateurs, et (iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester antenne. conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, énoncée à Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires la section 6.2.2.3, doivent être clairement indiqués sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de Approved Antenna List conformité supplémentaires requis pour ce module installé. This radio transmitter (IC: 1693B-HONST60 / Model: HON-ST60 ) has been approved by Innovation, Science and Economic Development Canada to IMPORTANT NOTE: operate with the antenna types listed below, with the maximum permissible In the event that these conditions cannot be met (for example certain laptop gain indicated. Antenna types not included in this list that have a gain greater configurations or co-location with another transmitter), then the Canada than the maximum gain indicated for any type listed are strictly prohibited for authorization is no longer considered valid and the IC ID cannot be used on the use with this device. final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a Antenna manufacturer / model Laird MAF94367 separate Canada authorization. Antenna Type Dipole Antenna Antenna connector R-TNC NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation Liste des antennes approuvées avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme Cet émetteur radio (IC: 1693B-HONST60 / Model: HON-ST60 ) a été valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces approuvé par Innovation, Sciences et Développement économique Canada pour circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y fonctionner avec les types d'antenne énumérés ci-dessous, avec le gain maximal compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. autorisé indiqué. Les types d'antenne non inclus dans cette liste et dont le gain est supérieur au gain maximal indiqué pour l'un des types répertoriés ne sont End Product Labeling strictement pas autorisés pour une utilisation avec cet appareil. This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and Antenne fabricant / modèle Laird MAF94367 users. The final end product must be labeled in a visible area with the Type d'antenne Dipole Antenna following: “Contains IC:1693B-HONST60”. Connecteur d'antenne R-TNC Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 1693B-HONST60". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.



Document Created: 2019-07-18 19:16:07
Document Modified: 2019-07-18 19:16:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC