Annex_E_-_Equipment_Calibration_Report_Part1

FCC ID: HD5-EDA710

RF Exposure Info

Download: PDF
FCCID_4296410

Allllv'\ mam Euibrt Dutrich wiuleletertiaiebeiieetbetiaiisntinintaberbetia in w a a \“\u||,,,l, . Callb':at'on Laboratory of S‘\\\\/_&'A} S Schweizerischer Kalibrierdienst Schmid & Partner ila\é—-/mé C Service suisse d‘étalonnage Engmeerlng AG g zo yny Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {«/,l/,fi\“\? S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client MRT—CQC (Auden) Certificate No: D2450V2—1013_May18 CALIBRATION CERTIFICATE Object D2450V2 — SN:1013 Calibration procedure(s) QA CAL—O5.v10 Calibration procedure for dipole validation kits above 700 MHz Calibration date: May 09, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 7349 30—Dec—17 (No. EX3—7349_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—O6 SN: 100972 15—Jun—15 (in house check Oct—16) in house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 ({in house check Oct—17) in house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician Approved by: Katia Pokovic Technical Manager % Issued: May 9, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2—1013_May18 Page 1 of 8

a a wl 1 9, Ca"br_'atlon Laboratory of s\‘\‘\/"/,; Schweizerischer Kalibrierdienst Schmid & Partner m Service suisse d‘étalonnage EnglneerIng AG < //_—\\ T Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘f/,,/fi\@? Swiss Calibration Service Alululs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) 1EC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—1013_May18 Page 2 of 8

Measurement Conditions DASY system configuration, as far as not giTven on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz +1 MHz Head TSL parameters The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 38.3 +6 % 1.86 mho/m + 6 % Head TSL temperature change during test <0.5 °C ———— ———— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.3 W/kg SAR for nominal Head TSL parameters normalized to 1W 52.1 W/kg + 17.0 % (k=2) SAR averaged over 10 cm*‘ (10 g) of Head TSL condition SAR measured 250 mW input power 6.18 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.4 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 52.5 +6 % 2.01 mho/m +6 % Body TSL temperature change during test <0.5 °C ———— ———— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.8 W/kg SAR for nominal Body TSL parameters normalized to 1W 50.4 W/kg + 17.0 % (k=2) SAR averaged over 10 cm® (10 g) of Body TSL condition SAR measured 250 mW input power 5.96 W/kg SAR for nominal Body TSL parameters normalized to 1W 23.6 W/ikg + 16.5 % (k=2) Certificate No: D2450V2—1013_May18 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 53.3 Q + 2.4 jQ Return Loss — 28.0 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.8 Q + 3.9 jQ Return Loss — 28.2 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.156 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 17, 2017 Certificate No: D2450V2—1013_May18 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 09.05.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:1013 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.86 S/m; & = 38.3; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(7.88, 7.88, 7.88) @ 2450 MHz; Calibrated: 30.12.2017 Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAF4 Sn601; Calibrated: 26.10.2017 Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm,/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=>5mm, dy=5mm, dz=5mm Reference Value = 116.1 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 26.6 W/kg SAR(1 g) = 13.3 W/kg; SAR(10 g) = 6.18 W/kg Maximum value of SAR (measured) = 21.9 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 21.9 W/kg = 13.40 dBW/kg Certificate No: D2450V2—1013_May18 Page 5 of 8

Impedance Measurement Plot for Head TSL 9 May 2018 08:08:02 [CHT) s11 1 U FS 1: 53.28i1s: 24453 6 1458.85 pH 2 450,.000 9DA MHz —~ ~—. Oe 1 CaA Av 168 H1d CH2 CA Ax 16 2 H1 4 START 2 250.900 900 MHz STOF 2 £50.000 000 MHz Certificate No: D2450V2—1013_May18 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 09.05.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:1013 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f= 2450 MHz; 0 = 2.01 S$/m; s = 52.5; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(8.01, 8.01, 8.01) @ 2450MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAF4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.1 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 25.3 W/kg SAR(1 g) = 12.8 W/kg; SAR(10 g) = 5.96 W/kg Maximum value of SAR (measured) = 20.9 W/kg dB 0 —5.00 —10.00 ~15.00 —20.00 —25.00 0 dB = 20.9 W/kg = 13.20 dBW/kg Certificate No: D2450V2—1013_May18 Page 7 of 8

Impedance Measurement Plot for Body TSL 9 May 2018 @8106157 CHI s1ii i1 U FS 1149.793 8 38965 m 253.12 pH 2 4590.000 @@d MHz y Cmy x & aeths A & is se _ ~ _ ~P J% ¢ &\ & + * A Del & \'}'f o se ~1 ol 3 & = . § TA 4 "~ . s a '&_‘h, Ca j 3 { e3 }>~ N 1 V- T _‘ > \ t s T 3 . t £ou2 o \ }‘u 2T § Aug 16 \* se => £o0 ud p—‘g TT sy "S‘ “_/ H1ld CHZ C& npa 16° H1d SThART ? 250.900 AGo MHz STOFP ? 6590.000 B0b MHz Certificate No: D2450V2—1013_May18 Page 8 of 8

. 3 w19E Calibration Laboratory of \“\\\\_//I/"/ Schweizerischer Kalibrierdienst Schmid & Partner i\B\E'_%& c Service suisse d‘étalonnage Engineering AG ¥ /a s Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland & n S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Auden Certificate No: D5GHzV2—1040_Jun18 CALIBRATION CERTIFICATE Object D5SGHzV2 — SN:1040 Calibration procedure(s) QA CAL—22.v3 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: June 28, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EXSDV4 SN: 3503 30—Dec—17 (No. EX3—3503_Dec17) Dec—18 DAE4 SN: 601 26—0ct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician | Approved by: KatJa Pokovic Technical Manager %g Issued: June 28, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1040_Jun18 Page 1 of 16

Calibration . Laboratory of sFuy \/ *z S Schweizerischer Kalibrierdienst Schmid & Partner iia%//ufi c Service suisse d‘étalonnage Engineering AG T //—\\ g Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/a/Q\ w S swiss Calibration Service thilabe® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1040_Jun18 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5300 MHz & 1 MHz Frequency 5500 MHz + 1 MHz 5600 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 36.1 +6 % 4.55 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5200 MHz SAR averaged over 1 em* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.88 W/kg SAR for nominal Head TSL parameters normalized to 1W 78.8 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.27 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 3 of 16

Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 36.0 +6 % 4.66 mho/m + 6 % Head TSL temperature change during test <0.5 °C ———— ———— SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.22 W/kg SAR for nominal Head TSL parameters normalized to 1W 82.2 W / kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.36 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.6 W/kg + 19.5 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 35.7 26 % 4.86 mho/m + 6 % Head TSL temperature change during test <0.5°C ———— ———— SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.34 W/kg SAR for nominal Head TSL parameters normalized to 1W 83.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.38 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.8 W/kg £ 19.5 %(k=2) Certificate No: D5GHzV2—1040_Jun18 Page 4 of 16

Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.5 + 6 % 4.97 mho/m + 6 % Head TSL temperature change during test «05 °C sese sees SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.54 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 85.3 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.45 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.5 Wikg 19.5 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.2 + 6 % 5.18 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~«—— ~—— SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.07 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.6 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 23.0 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 5 of 16

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 £0.2) °C 47.0 x6 % 5.45 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~——— «==> SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.58 W/kg SAR for nominal Body TSL parameters normalized to 1W 75.2 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 211 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.9 Wikg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.8 + 6 % 5.58 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— ~——— SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.70 W/kg SAR for nominal Body TSL parameters normalized to 1W 76.4 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.16 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 6 of 16

Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 46.5 + 6 % 5.85 mho/m + 6 % Body TSL temperature change during test <0.5 °C ——— ««+~ SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 8.25 W/kg SAR for nominal Body TSL parameters normalized to 1W 81.9 Wikg * 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 2.28 W/kg SAR for nominal Body TSL parameters normalized to 1W 22.6 Wikg + 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 x 6 % 5.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— ———— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.21 W/kg SAR for nominal Body TSL parameters normalized to 1W 81.5 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.29 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.7 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 7 of 16

Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.0 + 6 % 6.26 mho/m + 6 % Body TSL temperature change during test <0.5 °C me«+ «+ SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.79 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.3 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.15 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.3 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 50.5 Q — 8.6 jQ Return Loss —21.3 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 49.3 Q — 2.8 jQ Return Loss — 30.8 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 50.2 Q — 6.1 jQ Return Loss —24.4 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 56.8 Q — 2.0 jQ Return Loss —23.6 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 54.4 Q — 1.0 jQ Return Loss — 27.3 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 49.8 Q — 7.7 jQ Return Loss —22.3 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 49.1 Q —1.8 jQ Return Loss —34.1 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 50.5 Q — 4.8 jQ Return Loss — 26.3 dB Certificate No: D5GHzV2—1040_Jun18 Page 9 of 16

Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 57.6 Q — 2.4 jQ Return Loss — 22.6 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 55.1 Q — 1.3 jQ Return Loss —26.0 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.203 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on December 30, 2005 Certificate No: D5GHzV2—1040_Jun18 Page 10 of 16

DASY5 Validation Report for Head TSL Date: 28.06.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5SGHzV2; Serial: DSGHzV2 — SN:1040 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 6 = 4.55 S/m; & = 36.1; p = 1000 kg/m" . Medium parameters used: f = 5300 MHz; 0 = 4.66 S/m; &, = 36; p = 1000 kg/m“ 3 Medium parameters used: f = 5500 MHz; o = 4.86 S/m; . = 35.7; p = 1000 kg/m3 , Medium parameters used: f = 5600 MHz; o = 4.97 $/m; &, = 35.5; p = 1000 kg/m3 ¢ Medium parameters used: f = 5800 MHz; 0 = 5.18 S/m; &, = 35.2; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.75, 5.75, 5.75) @ 5200 MHz, ConvF(5.5, 5.5, 5.5) @ 5300 MHz, ConvF(5.2, 5.2, 5.2) @ 5500 MHz, ConvF(5.05, 5.05, 5.05) @ 5600 MHz, ConvF(4.96, 4.96, 4.96) @ 5800 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601 (5GHz); Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.83 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 27.8 W/kg SAR(1 g) = 7.88 W/kg; SAR(10 g) = 2.27 W/kg Maximum value of SAR (measured) = 17.7 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.69 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 29.8 W/kg SAR(1 g) = 8.22 W/kg; SAR(10 g) = 2.36 W/kg Maximum value of SAR (measured) = 18.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.52 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 31.8 W/kg SAR(1 g) = 8.34 W/kg; SAR(10 g) = 2.38 W/kg Maximum value of SAR (measured) = 19.3 W/kg Certificate No: D5GHzV2—1040_Jun18 Page 11 of 16

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 76.52 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 31.9 W/kg SAR(1 g) = 8.54 W/kg; SAR(10 g) = 2.45 W/kg Maximum value of SAR (measured) = 19.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 73.34 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 31.6 W/kg SAR(I g) = 8.07 W/kg; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 19.1 W/kg dB 0 —6.00 —12.00 —18.00 —24.00 —30.00 0 dB = 17.7 W/kg = 12.48 dBW/kg Certificate No: D5GHzV2—1040_Jun18 Page 12 of 16

Impedance Measurement Plot for Head TSL 28 Jun 2018 @7:29:36 (CHZ sii 4o uors 1150477 a —8.6309 0 3.5462 pF 5 200.000 000 MHz * CH1 Markers Be+ 2 49.944 a —2.7695 a Sor 5.30000 GHz at $0,234 a —6.0645 a 5.50000 GHz 41 56.771 a —1.9598 a fvsg 5.G0000 GHz 16 5t 54.406 a —1,.0254 a 5.80000 GHz H1d CH2 CH2 Markers 2:—30.849 dB for 5.30000 GHz t—24.968 dB 5.50000 GHz 41—23.609 dB ee 5.60000 GHz 16 5:—27.260 dB 5.90000 GHz H1d START 5 000.000 000 MHz STOP 6 000.000 0d MHz Certificate No: D5GHzV2—1040_Jun18 Page 13 of 16

DASY5 Validation Report for Body TSL Date: 27.06.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: DSGHzV2; Serial: D5SGHzV2 — SN:1040 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 5.45 S/m; . = 47; p = 1000 kg/m} M Medium parameters used: f = 5300 MHz; 0 = 5.58 S/m; &, = 46.8; p = 1000 kg/m‘ , Medium parameters used: f = 5500 MHz; 0 = 5.85 $/m; s, = 46.5; p = 1000 kg/m3 , Medium parameters used: f = 5600 MHz; 0 = 5.99 $/m; &, = 46.3; p = 1000 kg/m‘ , Medium parameters used: f= 5800 MHz; 0 = 6.26 S/m; &, = 46; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.35, 5.35, 5.35) @ 5200 MHz, ConvF(5.15, 5.15, 5.15) @ 5300 MHz, ConvF(4.7, 4.7, 4.7) @ 5500 MHz, ConvF(4.65, 4.65, 4.65) @ 5600 MHz, ConvF(4.53, 4.53, 4.53) @ 5800 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601 (5GHz); Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.84 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 28.1 W/kg SAR(1 g) =7.58 W/kg; SAR(10 g) =2.11 W/kg Maximum value of SAR (measured)= 17.1 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.55 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(1 g) = 7.7 W/kg; SAR(10 g) = 2.16 W/kg Maximum value of SAR (measured) = 17.6 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.16 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 33.4 W/kg SAR(I g) = 8.25 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (measured) = 19.3 W/kg Certificate No: D5GHzV2—1040_Jun18 Page 14 of 16

Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.09 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 34.0 W/kg SAR(I g) = 8.21 W/kg; SAR(10 g) = 2.29 W/kg Maximum value of SAR (measured) = 19.5 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.60 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 33.5 W/kg SAR(I g) =7.79 W/kg; SAR(10 g) = 2.15 W/kg Maximum value of SAR (measured) = 18.8 W/kg dB —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 18.8 W/kg = 12.74 dBW/kg Certificate No: D5GHzV2—1040_Jun18 Page 15 of 16


Document Created: 2019-05-24 17:12:27
Document Modified: 2019-05-24 17:12:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC