1805RSU004-U6-FCC-DXX Test Report

FCC ID: HD5-EDA510

Test Report

Download: PDF
FCCID_3873998

MRT Technology (Suzhou) Co., Ltd Report No.: 1805RSU004-U6 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 05-17-2018 MEASUREMENT REPORT FCC PART 15.225 / RSS-210 NFC 13.56MHz FCC ID: HD5-EDA510 IC: 1693B-EDA510 APPLICANT: Honeywell International Inc Honeywell Safety and Productivity Solutions Application Type: Certification Product: Mobile Computer Model No.: EDA51-0 Brand Name: Honeywell FCC Classification: Part 15 Low Power Communication Device Transmitter (DXX) FCC Rule Part(s): Part 15 Subpart C (Section 15.225) IC Rule(s): RSS 210 Issue 9, RSS-GEN Issue 5 Test Procedure(s): ANSI C63.10-2013 Test Date: May 04 ~ May 17, 2018 Reviewed By : ( Jame Yuan ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. FCC ID: HD5-EDA510 Page Number: 1 of 28 IC: 1693B-EDA510

Report No.: 1805RSU004-U6 Revision History Report No. Version Description Issue Date Note 1805RSU004-U6 Rev. 01 Initial Report 05-17-2018 Valid FCC ID: HD5-EDA510 Page Number: 2 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 5 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description.................................................................................................. 7 2.2. Test Mode .................................................................................................................... 7 2.3. Device Capabilities ....................................................................................................... 7 2.4. Test Configuration ........................................................................................................ 7 2.5. EMI Suppression Device(s)/Modifications ..................................................................... 7 2.6. Labeling Requirements ................................................................................................. 8 3. DESCRIPTION OF TEST ........................................................................................................ 9 3.1. Evaluation Procedure ................................................................................................... 9 3.2. AC Line Conducted Emissions ..................................................................................... 9 3.3. Radiated Emissions .................................................................................................... 10 4. ANTENNA REQUIREMENTS .................................................................................................11 5. TEST EQUIPMENT CALIBRATION DATA ............................................................................ 12 6. MEASUREMENT UNCERTAINTY ......................................................................................... 13 7. TEST RESULT ...................................................................................................................... 14 7.1. Summary .................................................................................................................... 14 7.2. In-band Emission ........................................................................................................ 15 7.2.1. Test Limit ................................................................................................................ 15 7.2.2. Test Procedure Used .............................................................................................. 15 7.2.3. Test Setup............................................................................................................... 16 7.2.4. Test Result .............................................................................................................. 17 7.3. Out-band Emission ..................................................................................................... 18 7.3.1. Test Limit ................................................................................................................ 18 7.3.2. Test Procedure Used .............................................................................................. 18 7.3.3. Test Setup............................................................................................................... 19 7.3.4. Test Result .............................................................................................................. 20 7.4. 20dB Bandwidth ......................................................................................................... 21 7.4.1. Test Limit ................................................................................................................ 21 7.4.2. Test Procedure Used .............................................................................................. 21 FCC ID: HD5-EDA510 Page Number: 3 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.4.3. Test Setup............................................................................................................... 21 7.4.4. Test Result .............................................................................................................. 22 7.5. Frequency Tolerence .................................................................................................. 23 7.5.1. Test Limit ................................................................................................................ 23 7.5.2. Test Procedure Used .............................................................................................. 23 7.5.3. Test Setup............................................................................................................... 23 7.5.4. Test Result .............................................................................................................. 24 7.6. AC Conducted Emissions Measurement..................................................................... 25 7.6.1. Test Limit ................................................................................................................ 25 7.6.2. Test Setup............................................................................................................... 25 7.6.3. Test Result .............................................................................................................. 26 8. CONCLUSION....................................................................................................................... 28 FCC ID: HD5-EDA510 Page Number: 4 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 §2.1033 General Information Applicant: Honeywell International Inc Honeywell Safety and Productivity Solutions Applicant Address: 9680 Old Bailes Road, Fort Mill, SC 29707 United States Manufacturer: Honeywell International Inc Honeywell Safety and Productivity Solutions Manufacturer Address: 9680 Old Bailes Road, Fort Mill, SC 29707 United States Test Site: MRT Technology (Suzhou) Co., Ltd Test Site Address: D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China MRT FCC Registration No.: 893164 MRT IC Registration No.: 11384A-1 Test Device Serial No.: N/A Production Pre-Production Engineering Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Tian’edang Rd., Suzhou, China.  MRT facility is a FCC registered (MRT Reg. No. 893164) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules.  MRT facility is an IC registered (MRT Reg. No. 11384A-1) test laboratory with the site description on file at Industry Canada.  MRT facility is a VCCI registered (R-20025, G-20034, C-20020, T-20020) test laboratory with the site description on file at VCCI Council.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (A2LA) under the American Association for Laboratory Accreditation Program (A2LA Cert. No. 3628.01) in EMC, Telecommunications and Radio testing for FCC, Industry Canada, EU and TELEC Rules. FCC ID: HD5-EDA510 Page Number: 5 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taihu Lake. These measurement tests were conducted at the MRT Technology (Suzhou) Co., Ltd. Facility located at D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on September 30, 2013. FCC ID: HD5-EDA510 Page Number: 6 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name: Mobile Computer Model No.: EDA51-0 Brand Name: Honeywell Wi-Fi Specification: 802.11a/b/g/n/ac Bluetooth Version: V4.2 dual mode NFC: 13.56MHz Accessories USB Adapter: Model No.: ADS-12B-06 05010E Input Power: 100 - 240V ~ 50/60Hz, Max. 0.3A Output Power: 5VDC 2.0A Battery: Model No.: BAT-EDA50US Capacitance: 15.2Wh, 4000mAh Rated Voltage: 3.8V 2.2. Test Mode Test Mode Mode 1: Transmit by NFC 2.3. Device Capabilities This device contains the following capabilities: 2.4GHz WLAN (DTS) & 5GHz WLAN (UNII) & Bluetooth (v4.2 dual mode) & NFC 2.4. Test Configuration The Mobile Computer was set to continuous transmission. This was performance using manufacturer software loaded on the terminal to allow for continuous transmission. This device was tested in accordance with the guidance of ANSI C63.10-2013. ANSI C63.4-2014 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 2.5. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. FCC ID: HD5-EDA510 Page Number: 7 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 2.6. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. RSP-100 Issue 11 Section 3 The manufacturer, importer or distributor shall meet the labelling requirements set out in this section for every unit: (i) prior to marketing in Canada, for products manufactured in Canada (ii) prior to importation into Canada, for imported products For information regarding the e-labelling option, see Notice 2014-DRS1003. The label for the certified product represents the manufacturer’s or importer’s compliance with Innovation, Science and Economic Development Canada’s (ISED) regulatory requirements. Please see attachment for IC label and label location. FCC ID: HD5-EDA510 Page Number: 8 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed Wireless Devices (ANSI C63.10-2013) was used in the measurement. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an 8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150kHz to 30MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or data exchange speed, or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions are used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. An extension cord was used to connect to a single LISN which powered by EUT. The extension cord was calibrated with LISN, the impedance and insertion loss are compliance with the requirements as stated in ANSI C63.10-2013 at Clause 4.3. FCC ID: HD5-EDA510 Page Number: 9 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. A MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remote controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 0.8 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB Beam-Width of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: HD5-EDA510 Page Number: 10 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 4. ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna of the Mobile Computer is permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The unit complies with the requirement of §15.203. FCC ID: HD5-EDA510 Page Number: 11 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 5. TEST EQUIPMENT CALIBRATION DATA Conducted Emission - SR2 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date EMI Test Receiver R&S ESR7 MRTSUE06001 1 year 2018/08/18 Two-Line V-Network R&S ENV 216 MRTSUE06002 1 year 2018/06/21 Two-Line V-Network R&S ENV 216 MRTSUE06003 1 year 2018/06/21 Thermohygrometer Testo 608-H1 MRTSUE06404 1 year 2018/08/14 Shielding Anechoic Chamber Mikebang Chamber-SR2 MRTSUE06214 N/A N/A Radiated Emissions - AC1 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date PXA Signal Analyzer Keysight 9030B MRTSUE06395 1 year 2018/09/13 EMI Test Receiver R&S ESR7 MRTSUE06001 1 year 2018/08/18 Microwave System Amplifier Agilent 83017A MRTSUE06076 1 year 2018/11/17 Loop Antenna Schwarzbeck FMZB 1519 MRTSUE06025 1 year 2018/11/20 Bilog Period Antenna Schwarzbeck VULB 9168 MRTSUE06172 1 year 2018/11/18 Broad Band Horn Antenna Schwarzbeck BBHA9120D MRTSUE06023 1 year 2018/10/21 Broad Band Horn Antenna Schwarzbeck BBHA 9170 MRTSUE06024 1 year 2018/12/14 Amplifier Schwarzbeck BBV 9721 MRTSUE06121 1 year 2018/06/14 Thermohygrometer Testo 608-H1 MRTSUE06403 1 year 2018/08/14 Anechoic Chamber TDK Chamber-AC1 MRTSUE06212 1 year 2019/05/02 Software Version Function EMI Software V3 EMI Test Software FCC ID: HD5-EDA510 Page Number: 12 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 6. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement - SR2 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 150kHz~30MHz: 3.46dB Radiated Emission Measurement - AC1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 9kHz ~ 1GHz: 4.18dB 1GHz ~ 25GHz: 4.76dB FCC ID: HD5-EDA510 Page Number: 13 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7. TEST RESULT 7.1. Summary Product Name: Mobile Computer FCC ID: HD5-EDA510 IC: 11693B-EDA510 FCC Part RSS Test Description Test Limit Test Test Reference Section(s) Section(s) Condition Result 15,848uV/m @ 30m 13.553 ~ 13.567 MHz 334uV/m @ 30m RSS-210 15.225 In-Band 13.410 ~ 13.553 MHz [B.6] Pass Section 7.2 (a), (b), (c) Emission 13.567 ~ 13.710 MHz (a), (b), (c) 106uV/m @ 30m 13.110 ~ 13.410 MHz 13.710 ~ 14.010 MHz Emissions outside of the specified band Radiated RSS-210 Out-Band (13.110~14.010 MHz) 15.225(d) [B.6] Pass Section 7.3 Emission must meet the radiated (d) limits detailed in 15.209 RSS-Gen 2.1049 20dB Bandwidth N/A Pass Section 7.4 [6.7] Frequency RSS-210 ±0.01% of operating 15.225(e) Stability Pass Section 7.5 [B.6] frequency Tolerance AC Conducted RSS-Gen Line 15.207 Emissions < FCC 15.207 limits Pass Section 7.6 [8.8] Conducted 150kHz - 30MHz Notes: 1) All modes of operation and data rates were investigated. For radiated emission test, every axis (X, Y, Z) was also verified. The test results shown in the following sections represent the worst case emissions. 2) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. FCC ID: HD5-EDA510 Page Number: 14 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.2. In-band Emission 7.2.1.Test Limit FCC Part 15 Subpart C Paragraph 15.225 & RSS-210 Section [B.6] Frequency Distance Level (MHz) (m) (uV/m) 13.553 ~13.567 30 15,848 13.410 ~13.553 30 334 13.567 ~13.710 13.110 ~13.410 30 106 13.710 ~14.010 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBuV/m) = 20 log E field strength (uV/m) 7.2.2.Test Procedure Used The EUT was setup according to ANSI C63.4, 2009 and tested according to ANSI C63.10: 2009 for compliance to FCC 47CFR 15.247 requirements. The EUT is placed on a turn table which is 0.8 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. This is repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.4:2009 on radiated measurement. The EUT should be operate in transmission mode. FCC ID: HD5-EDA510 Page Number: 15 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.2.3.Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: FCC ID: HD5-EDA510 Page Number: 16 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.2.4.Test Result Test Engineer Snake Ni Temperature 25°C Test Time 2018/05/15 Relative Humidity 56% Test Mode Mode1 Test Site AC1 Frequency Reading Factor Measure Limit(3m) Margin Level(dBuV/m) (dB) Level(dBuV/m) [dBuV/m] [dB] Face On 13.35 15.55 19.85 35.40 80.51 -45.11 13.45 16.83 19.86 36.69 90.47 -53.78 13.56 37.95 19.87 57.82 123.99 -66.18 13.70 12.19 19.87 32.06 90.47 -58.42 13.81 9.07 19.88 28.95 80.51 -51.56 Face Off 13.31 7.53 19.85 27.38 80.51 -53.13 13.46 16.60 19.86 36.47 90.47 -54.01 13.56 38.92 19.86 58.79 123.99 -65.20 13.70 14.29 19.87 34.15 90.47 -56.32 13.77 18.06 19.87 37.94 80.51 -42.58 Note1: All measurements were performed using a loop antenna. The antenna was positioned in two orthogonal (face on and face off) and the position with the highest emission level was recorded. Note2: Measurements were tested at 3m and the data was extrapolated to the specified measurement distance of 30m using the square of an inverse linear extrapolation factor (40 dB/decade) as specified in &15.31(f)(2). Extrapolation Factor = 40*Log(30/3) = 40 dB Note3: All measurements were recorded using a EMI test receiver employing a peak detector. FCC ID: HD5-EDA510 Page Number: 17 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.3. Out-band Emission 7.3.1.Test Limit FCC Part 15 Subpart C Paragraph 15.209 & RSS-Gen Section 8.9 Frequency Distance Level (MHz) (m) (uV/m) 0.009 - 0.490 300 2400/F (kHz) 0.490 - 1.705 30 2400/F (kHz) 1.705 - 30 30 30 30 - 88 3 100 88 - 216 3 150 216 - 960 3 200 Above 960 3 500 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBuV/m) = 20 log E field strength (uV/m) 7.3.2.Test Procedure Used The EUT was tested from 9kHz up to the 1GHz excluding the band 13.110-14.010 MHz. All measurements were recorded with a spectrum analyzer employing an average detector for emissions below 30MHz. Above 30MHz a Quasi-peak detector was used. All out-of-band emissions must not exceed the limits shown as stated per Section 15.209. A loop antenna was used for searching for emissions below 30MHz. FCC ID: HD5-EDA510 Page Number: 18 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.3.3.Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: FCC ID: HD5-EDA510 Page Number: 19 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.3.4.Test Result Test Engineer Snake Ni Temperature 25°C Test Time 2018/05/15 Relative Humidity 56% Test Mode Mode1 Test Site AC1 Out-Band Emission Below 30MHz Frequency Reading Factor Measure Limit Margin (dB) Detector (MHz) Level (dB) Level (dBuV/m) (dBuV/m) (dBuV/m) Face On 27.12 9.44 19.51 28.95 69.54 -40.59 QP Face Off 27.12 7.18 19.51 26.69 69.54 -42.85 QP Out-Band Emission Above 30MHz Antenna Frequency Reading Factor Measure Limit Margin (dB) Detector (MHz) Level (dB) Level (dBuV/m) (dBuV/m) (dBuV/m) H 40.67 3.44 14.58 18.02 40.00 -21.98 QP H 67.83 1.65 11.99 13.64 40.00 -26.36 QP H 147.86 0.43 15.14 15.57 43.50 -27.93 QP H 175.99 2.93 13.50 16.43 43.50 -27.07 QP H 518.40 1.21 18.94 20.15 46.00 -25.85 QP H 728.89 2.84 22.51 25.35 46.00 -20.65 QP V 40.67 3.43 14.58 18.01 40.00 -21.99 QP V 125.55 1.43 13.57 15.00 43.50 -28.50 QP V 159.01 1.02 15.29 16.31 43.50 -27.19 QP V 519.85 2.43 18.97 21.40 46.00 -24.60 QP V 594.06 2.34 20.46 22.80 46.00 -23.20 QP V 729.37 2.11 22.52 24.63 46.00 -21.38 QP Note1: All measurements were performed using a loop antenna. The antenna was positioned in two orthogonal (face on and face off) and the position with the highest emission level was recorded. Note2: Measurements were tested at 3m and the data was extrapolated to the specified measurement distance of 30m using the square of an inverse linear extrapolation factor (40 dB/decade) as specified in &15.31(f)(2). Extrapolation Factor = 40*Log(30/3) = 40 dB Note3: All measurements were recorded using a EMI test receiver employing a peak detector. FCC ID: HD5-EDA510 Page Number: 20 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.4. 20dB Bandwidth 7.4.1.Test Limit N/A 7.4.2.Test Procedure Used The 20dB bandwidth is measured with a spectrum analyzer connected via a receive antenna placed near the EUT while the EUT is operating in transmission mode. 7.4.3.Test Setup FCC ID: HD5-EDA510 Page Number: 21 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.4.4.Test Result Test Engineer Snake Ni Temperature 25°C Test Time 2018/05/15 Relative Humidity 56% Test Mode Mode1 Test Site AC1 Frequency Occupied Bandwidth (MHz) (kHz) 13.56 114.04 FCC ID: HD5-EDA510 Page Number: 22 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.5. Frequency Tolerence 7.5.1.Test Limit The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency. 7.5.2.Test Procedure Used The equipment under test was connected to an external AC or DC power supply and input rated voltage. RF output was connected to a frequency counter or spectrum analyzer via feed through attenuators. The EUT was placed inside the temperature chamber. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and measure EUT 20°C operating frequency as reference frequency. Turn EUT off and set the chamber temperature to highest. After the temperature stabilized for approximately 30 minutes recorded the frequency. Repeat step measure with 10°C decreased per stage until the lowest temperature reached. 7.5.3.Test Setup FCC ID: HD5-EDA510 Page Number: 23 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.5.4.Test Result Test Engineer Snake Ni Temperature 25°C Test Time 2018/05/15 Relative Humidity 56% Test Mode Mode1 Test Site AC1 Operating Frequency: 13.56MHz Reference Voltage: 3.8Vdc Deviation Limit: +/- 0.01% = 1356Hz Voltage Power TEMP FREQ. FREQ. Dev. Deviation (%) Battery (°C) (Hz) (Hz) (%) -20 13,560,346 346 0.002552 -10 13,560,387 387 0.002854 0 13,559,453 453 0.003341 +10 13,560,556 556 0.004100 100% 3.80 +20 (Ref) 13,560,650 650 0.004794 +30 13,560,692 692 0.005103 +40 13,560,764 764 0.005634 +50 13,560,775 775 0.005715 115% 4.37 + 20 13,560,765 765 0.005642 85% 3.23 + 20 13,560,454 454 0.003348 FCC ID: HD5-EDA510 Page Number: 24 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.6. AC Conducted Emissions Measurement 7.6.1.Test Limit FCC Part 15 Subpart C Paragraph 15.207 & RSS-Gen Section 8.8 Frequency QP AV (MHz) (dBuV) (dBuV) 0.15 - 0.50 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 7.6.2.Test Setup FCC ID: HD5-EDA510 Page Number: 25 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 7.6.3.Test Result Site: SR2 Time: 2018/05/08 - 16:22 Limit: FCC_Part15.207_CE_AC Power Engineer: Polly Zong Probe: ENV216_101683_Filter On Polarity: Line EUT: Mobile Computer Power: AC 120V/60Hz Test Mode: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.150 24.318 13.149 -41.682 66.000 11.168 QP 2 0.150 10.232 -0.937 -45.768 56.000 11.168 AV 3 * 0.474 38.719 28.574 -17.725 56.444 10.145 QP 4 0.474 28.701 18.556 -17.742 46.444 10.145 AV 5 0.974 27.871 17.949 -28.129 56.000 9.922 QP 6 0.974 17.635 7.713 -28.365 46.000 9.922 AV 7 1.390 25.441 15.548 -30.559 56.000 9.893 QP 8 1.390 15.570 5.677 -30.430 46.000 9.893 AV 9 2.058 24.823 14.954 -31.177 56.000 9.869 QP 10 2.058 14.456 4.587 -31.544 46.000 9.869 AV 11 19.350 36.600 26.476 -23.400 60.000 10.124 QP 12 19.350 21.152 11.028 -28.848 50.000 10.124 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB). FCC ID: HD5-EDA510 Page Number: 26 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 Site: SR2 Time: 2018/05/08 - 16:29 Limit: FCC_Part15.207_CE_AC Power Engineer: Polly Zong Probe: ENV216_101683_Filter On Polarity: Neutral EUT: Mobile Computer Power: AC 120V/60Hz Test Mode: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.170 25.251 15.187 -39.709 64.960 10.064 QP 2 0.170 13.707 3.643 -41.253 54.960 10.064 AV 3 * 0.478 41.485 31.314 -14.889 56.374 10.170 QP 4 0.478 30.048 19.878 -16.325 46.374 10.170 AV 5 0.570 28.923 18.775 -27.077 56.000 10.148 QP 6 0.570 18.422 8.274 -27.578 46.000 10.148 AV 7 0.942 27.432 17.492 -28.568 56.000 9.941 QP 8 0.942 16.357 6.417 -29.643 46.000 9.941 AV 9 1.434 27.422 17.530 -28.578 56.000 9.893 QP 10 1.434 16.883 6.991 -29.117 46.000 9.893 AV 11 19.406 33.105 22.944 -26.895 60.000 10.161 QP 12 19.406 20.486 10.325 -29.514 50.000 10.161 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB). FCC ID: HD5-EDA510 Page Number: 27 of 28 IC: 11693B-EDA510

Report No.: 1805RSU004-U6 8. CONCLUSION The data collected relate only the item(s) tested and show that the Mobile Computer is in compliance with Part 15C of the FCC Rules and ISED rules. The End FCC ID: HD5-EDA510 Page Number: 28 of 28 IC: 11693B-EDA510


Document Created: 2018-05-29 23:50:37
Document Modified: 2018-05-29 23:50:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC