18C2057R-FCC-RF Exposure-Wireless Charge Rack-CN85-WCR-V1.0 0117

FCC ID: HD5-CX85WCR

RF Exposure Info

Download: PDF
FCCID_4132590

RF Exposure Evaluation Declaration Product Name : Wireless Charge Rack Model No. : CN85-WCR FCC ID : HD5-CX85WCR Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539 Date of Receipt : Dec. 12, 2018 Test Date Dec. 13, 2018~ Dec. 31, 2018 Issued Date : Jan. 07, 2019 Report No. : 18C2057R-RF-US-P20V01 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by A2LA or any agency of the government. The test report shall not be reproduced without the written approval of DEKRA Testing and Certification (Suzhou) Co., Ltd.

Report No: 18C2057R-RF-US-P20V01 Tes t R e p o r t C e r t i f i c a t i o n Issued Date : Jan. 07, 2019 Report No. : 18C2057R-RF-US-P20V01 Product Name : Wireless Charge Rack Applicant : HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions Address : 9680 OLD BAILES RD FORT MILL SC 29707-7539 Manufacturer : 1.HONEYWELL INTERNATIONAL INC Honeywell Safety and Productivity Solutions 2.RAYVAL (SUZHOU) TECHNOLOGIES CO LTD 3.Metro(Suzhou)Technologies Co.,Ltd Address : 1.9680 OLD BAILES RD FORT MILL SC 29707-7539 2.SUCHUN INDUSTRIAL SQUARE, BLDG 15A 428 XINGLONG STR SUZHOU INDUSTRIAL PARK SUZHOU JIANGSU 215126 CHINA 3.No.221 Xinghai street China-Singapore Suzhou Industrial Park Model No. : CN85-WCR FCC ID : HD5-CX85WCR Brand Name : Honeywell EUT Voltage : AC 120V/60Hz Applicable Standard : KDB 680106 D01 RF Exposure Wireless Charging Apps v03 Test Result : Complied Performed Location : DEKRA Testing and Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Delegation Number: CN1199 Documented By : ( Adm. Specialist: Kitty Li ) Reviewed By : (Senior Project Manager: Frank He ) Approved By : (Engineering Supervisor: Jack Zhang) Page: 2 of 19

Report No: 18C2057R-RF-US-P20V01 1. General Information 1.1. EUT Description Product Name Wireless Charge Rack Model No. CN85-WCR Working Voltage AC 120V/60Hz Frequency Range 110kHz~145KHz Type of Modulation ASK Page: 3 of 19

Report No: 18C2057R-RF-US-P20V01 1.2. Antenna information Model No. N/A Antenna manufacturer N/A Antenna Delivery 1*TX+1*RX 2*TX+2*RX 3*TX+3*RX Antenna technology SISO Basic CDD MIMO Sectorized Beam-forming Antenna Type Dipole External Sectorized PIFA PCB Internal Ceramic Chip Antenna Loop antenna Type F antenna Page: 4 of 19

Report No: 18C2057R-RF-US-P20V01 1.3. Mode of Operation DEKRA has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Test Mode Mode 1: Transmit Note: 1. Regards to the frequency band operation: the lowest､middle and highest frequency of channel were selected to perform the test, then shown on this report. 2. For portable device, radiated spurious emission was verified over X, Y, Z Axis, and shown the worst case on this report. Page: 5 of 19

Report No: 18C2057R-RF-US-P20V01 1.4. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 N/A N/A N/A N/A N/A Page: 6 of 19

Report No: 18C2057R-RF-US-P20V01 1.5. Configuration of Tested System Test setup Diagram- Radiated Emission Page: 7 of 19

Report No: 18C2057R-RF-US-P20V01 1.6. EUT Exercise Software 1 Setup the EUT and simulators as shown on above. 2 Turn on the power of equipment. 3 Start to continue transmit. Page: 8 of 19

Report No: 18C2057R-RF-US-P20V01 2. Technical Test 2.1. Test Environment Items Required (IEC 68-1) Actual Temperature (C) 15-35 21 Humidity (%RH) 25-75 50 Barometric pressure (mbar) 860-1060 950-1000 Page: 9 of 19

Report No: 18C2057R-RF-US-P20V01 3. Electric Field Strength 3.1. Test Equipment Electric Field Strength / AC-6 Instrument Manufacturer Type No. Serial No. Cal. Date Cal. Due Date Spectrum Analyzer Agilent N9010A MY48030494 2018.01.07 2019.01.06 Loop Antenna R&S HFH2-Z2 833799/003 2018.11.26 2019.11.25 MAGNETIC FIELD HiTESTER HIOKI FT3470-51 1009-B1 2018.10.11 2019.10.10 SUCOFLEX Coaxial Cable Huber+Suhner 106 AC2-C 2018.03.02 2019.03.01 Temperature/Humidity Meter Zhicheng ZC1-2 AC2-TH 2018.01.08 2019.01.07 Note: All equipment are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. Page: 10 of 19

Report No: 18C2057R-RF-US-P20V01 3.2. Test Setup 3kHz~10MHz Test Setup: Page: 11 of 19

Report No: 18C2057R-RF-US-P20V01 3.3. Setup Photo Page: 12 of 19

Report No: 18C2057R-RF-US-P20V01 3.4. Limit According to KDB 680106 D01v03 Clause 3.c: For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance of 15 cm. E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s) to the edge of the device. Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63 A/m. 3.5. Test Procedure a. Set the measurement frequency of the measurement probe to the fundamental frequency of the device under test. b. Set the span to encompass the entire emission bandwidth. c. Set the RBW greater than the 99% OBW of the fundamental emission. Note: This step is not required for a broadband measurement probe that integrates the entire frequency range. d. Set the detector to Peak and trace display to Max-Hold. e. Allow the spectrum to fill; for pulsing devices this may require an increased monitoring period. f. Using a marker, set it to the maximum level of the spectral envelope. g. Repeat steps (b) to (f) while scanning a parallel plane at the measurement distance of 10cm on each side of the device to find the peak level. h. Repeat steps (b) to (g) for any frequencies where the field value is greater than -20 dBc below the maximum level identified. i. If there are multiple frequencies transmitted by the device under test, use equations (2) and (3) to determine compliance. Note: When scanning around the entire device, the location found to be the maximum for the E- or H-field may not be the same location as the opposite field. Page: 13 of 19

Report No: 18C2057R-RF-US-P20V01 3.6. Uncertainty The measurement uncertainty is defined as ± 3.80 dB Page: 14 of 19

Report No: 18C2057R-RF-US-P20V01 3.7. Test Result Maximum Maximum Limit Axial Freq. Level Result (V/m) (kHz) (mV/m) X 110~145 18.123 307 Pass Y 110~145 25.704 307 Pass Z 110~145 9.1568 307 Pass Maximum Maximum Limit Axial Freq. Level Result (A/m) (kHz) (μA/m) X 110~145 362.46 0.815 Pass Y 110~145 514.08 0.815 Pass Z 110~145 183.14 0.815 Pass Page: 15 of 19

Report No: 18C2057R-RF-US-P20V01 X Axial-E Field: Y Axial-E Field: Page: 16 of 19

Report No: 18C2057R-RF-US-P20V01 Z Axial-E Field: X Axial-H Field: Page: 17 of 19

Report No: 18C2057R-RF-US-P20V01 Y Axial-H Field: Z Axial-H Field: Page: 18 of 19

Report No: 18C2057R-RF-US-P20V01 4. RF Exposure Evaluation WPT Device requirement Wireless power transfer frequency is below 1 MHz; Output power from each primary coil is less than or equal to 15 watts; The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Client device is placed directly in contact with the transmitter; Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Note: The WPT device can maintain all the six conditions above, so the RF exposure can be exempted. The End Page: 19 of 19


Document Created: 2019-04-01 22:56:23
Document Modified: 2019-04-01 22:56:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC