SAR Test Report-3

FCC ID: HD5-CN85L0N

RF Exposure Info

Download: PDF
FCCID_4309877

m® in Collaboration with !V CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 52.30 — 7.33j0 Return Loss — 22.50B Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 59.70 — 0.10jQ Return Loss —21.10B Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 54.40 + 0.39j0 Return Loss — 27.50B Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 52.00 — 8.24j0 Return Loss — 21.6dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 58.60 — 0.30jQ Return Loss — 22.00B Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 52.60 — 0.01jQ Return Loss — 32.00B Certificate No: Z18—60420 Page 7 of 14

’\® In Collaboration with m ‘/"/"J, s_ p__e_ a q -VCMM Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn General Antenna Parameters and Design Electrical Delay (one direction) 1.069 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60420 Page 8 of 14

smm© in Collsboration with ex‘/"7"J, ipaagyye~ a CALUBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn DASY5 Validation Report for Head TSL Date: 11.05.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1145 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; 0 = 4.848 S/im; er = 34.85; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 4.921 S/im; er = 34.47; p = 1000 kg/m3, Medium parameters used: f = 5750 MHz; 0 = 5.067 S/m; er = 34.42; p = 1000 kg/m3, Phantom section: Center Section DASY5 Configuration: e Probe: EX3DV4 — SN7514; ConvF(5.02, 5.02, 5.02) @ 5250 MHz; Calibrated: 8/27/2018, ConvF(4.41, 4.41, 4.41) @ 5600 MHz; Calibrated: 8/27/2018, ConvF(4.47, 4.47, 4.47) @ 5750 MHz; Calibrated: 8/27/2018, e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1555; Calibrated: 8/20/2018 * Phantom: MFP_V5.1C ; Type: QD 000 P51CA; Serial: 1062 e Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration /Pin=100mW, d=10mm, f=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 70.37 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 32.3 W/kg SAR(1 g) = 7.93 Wikg; SAR(10 g) = 2.26 Wikg Maximum value of SAR (measured) = 18.7 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 72.47 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 36.5 W/kg SAR(1 g) = 8.09 Wikg; SAR(10 g) = 2.3 W/ikg Maximum value of SAR (measured) = 19.5 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 71.77 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 37.5 W/kg SAR(1 g) = 7.98 W/kg; SAR(10 g) = 2.26 W/ikg Maximum value of SAR (measured) = 20.2 W/kg Certificate No: Z18—60420 Page 9 of 14

smm© in Collaboration with a_‘/"/"J, a ‘V CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en —20.17 —26.90 —33.62 0 dB = 20.2 W/ikg = 13.05 dBW/kg Certificate No: Z18—60420 Page 10 of 14

smm© in Collsboration with =_‘/"/‘]J, a Timaggs CAUBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn Impedance Measurement Plot for Head TSL Tri s11 Log Mag 10.00dB/ Ref 0.000ds [F1] * 00 z1 52500000 onz <22. 523 dBo 40.00 2 5.8000000 Ghz —21.060 des * 3 5.7500000 GHz —27.450 ds 30. 00 20. 00 10. 00 0. 000 p 4 —10. 00 —20. 00 —30. 00 —40. 00 —50.00 k T % J)- s11 smith (R+jX) scale 1.000Uu [F1i Del] »1 5.2500000 aHz 52.264 o —7.3260 o 4.13 2 5.6000000 GHz 59.711 n —98.585 mm 288.28 pF 3 5.7500000 GHz 54.411 t 386.65 mn A0.702 pH Certificate No: Z18—60420 Page 11 of 14

Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.eon DASY5 Validation Report for Body TSL Date: 11.06.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1145 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; 0 = 5.269 S/m; sr = 47.53; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.791 S/im; er = 47.12; p = 1000 kg/m3, Medium parameters used: f = 5750 MHz; 0 = 6.018 S/im; er = 46.88; p = 1000 kg/m3, Phantom section: Right Section DASY5 Configuration: e Probe: EX3DV4 — SN7514; ConvF(4.54, 4.54, 4.54) @ 5250 MHz; Calibrated: 8/27/2018, ConvF(4, 4, 4) @ 5600 MHz; Calibrated: 8/27/2018, ConvF(3.98, 3.98, 3.98) @ 5750 MHz; Calibrated: 8/27/2018, e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1555; Calibrated: 8/20/2018 e Phantom: MFP_V5.1C ; Type: QD 000 P51CA; Serial: 1062 * Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration /Pin=100mW, d=10mm, =5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.39 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 29.3 W/kg SAR(1 g) = 7.37 W/ikg; SAR(10 g) = 2.08 Wikg Maximum value of SAR (measured) = 17.0 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.81 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 34.4 W/kg SAR(1 g) = 7.8 Wikg; SAR(10 g) = 2.21 W/ikg Maximum value of SAR (measured) = 19.3 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 61.58 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 35.5 W/kg SAR(1 g) = 7.58 Wikg; SAR(10 g) = 2.12 Wikg Maximum value of SAR (measured) = 19.1 W/kg Certificate No: Z18—60420 Page 12 of 14

smm© in Collaboration with e=‘/"/"J, ‘, a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn —20.00 —26.67 —33.34 0 dB = 19.1 W/kg = 12.81 dBWi/kg Certificate No: Z18—60420 Page 13 of 14

smm© in Colleboration with e=x‘/"7"J, V a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn Impedance Measurement Plot for Body TSL Tri s11 Log Mag 10.00d8/ ref 0.000d8 [F1] 50. 00 I ~5.3500000 onz —21. 640 ds 4 2 5.6000000 GHz —22.047 dB 0.00 3 5.7500000 aHz —32.043 ds 30. 00 20. 00 10. 00 0. 000 j 4 —10. 00 —20. 00 t —30. 00 —~40, 00 —50.00 A PMWI si1 smith (R+jX) scale 1.000Uu [F1 Del] »L 5.2500000 GHz 51.989 n 2 5.6000000 GhHz 58.572 o 3 5.7500000 GHz 52.564 n Certificate No: Z18—60420 Page 14 of 14

a x sW I We Calibration Laboratory of ;\“\E//’«"?., g Schweizerischer Kalibrierdienst + S oz Schmid & Partner m C Service suisse d‘étalonnage Engineering AG ez ypo 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland */{;—Q\\\.\\‘ Swiss Calibration Service ty bs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client BV ADT (Auden) Certificate No: EX3—7472_Aug18 |CALIBRATION CERTIFICATE Object EX3DV4 — SN:7472 Calibration procedure(s) QA CAL—O01.v9, QA CAL—14.v4, QA CAL—23.v5, QA CAL—25.v6 Calibration procedure for dosimetric E—field probes Calibration date: August 29, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—291 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—291 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: $5277 (20x%) 04—Apr—18 (No. 217—02682) Apr—19 Reference Probe ES3DV2 SN: 3013 30—Dec—17 (No. ES3—3013_Dec17) Dec—18 DAE4 SN: 660 21—Dec—17 (No. DAE4—660_Dec17) Dec—18 Secondary Standards ID Check Date (in house) Scheduled Check Power meter E4419B SN: GB41293874 06—Apr—16 (in house check Jun—18) In house check: Jun—20 Power sensor E4412A SN: MY41498087 06—Apr—16 (in house check Jun—18) In house check: Jun—20 Power sensor E4412A SN: 000110210 06—Apr—16 (in house check Jun—18) In house check: Jun—20 RF generator HP 8648C SN: US3642U01700 04—Aug—99 (in house check Jun—18) In house check: Jun—20 Network Analyzer E8358A SN: US41080477 31—Mar—14 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician Approved by: Katja Pokovic Technical Manager %/g Issued: September 1, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: EX3—7472_Aug18 Page 1 of 39

Calibration . Laboratory of $stm NO\ S Schweizerischer Kalibrierdienst Schmid & Partner im C Service suisse d‘étalonnage Engineering AG F oy>o 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland f"’:/,fi.\\‘\c Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvrF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C, D modulation dependent linearization parameters Polarization q (p rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, ", "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand— held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) EC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). NORM(Px,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Ax,y,z; Bx.y,z; Cx,y,z; Dx,y,z; VRx,y,.z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip {on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: EX3—7472_Aug18 Page 2 of 39

EX3DV4 — SN:7472 August 29, 2018 Probe EX3DV4 SN:7472 Manufactured: October 25, 2016 Calibrated: August 29, 2018 Calibrated for DASY/EASY Systems {Note: non—compatible with DASY2 system!) Certificate No: EX3—7472_Aug18 Page 3 of 39

EX3DV4— SN:7472 August 29, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7472 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/m)*)* 0.59 0.49 0.42 +10.1 % DCP ({mVv)" 95.3 94.3 99.8 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc® dB dBvuV dB mV (k=2) 0 CW xX 0.0 0.0 1.0 0.00 133.5 +3.0% Y 0.0 0.0 1.0 133.6 Z 0.0 0.0 1.0 144.4 Note: For details on UID parameters see Appendix. Sensor Model Parameters C1 C2 a T1 T2 T3 T4 T5 T6 fF fF V ms.V~ ms.V~‘ ms V V~ 43.47 329.2 36.72 10.64 0.000 5.100 0.525 0.376 1.006 NJ <|% 31.96 249.6 38.64 3.696 0.054 5.076 0.000 0.365 1.009 31.17 231.4 35.20 4.593 0.000 5.009 0.488 0.187 1.003 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,Z do not affect the E®—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—7472_Aug18 Page 4 of 39

EX3DV4— SN:7472 August 29, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7472 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth ° Unce f(MHz)° Permittivity" (S/m)" ConvF X ConvFY¥ ConvFZ Aipha® _(mm) (k=2) 750 41.9 0.89 10.53 10.53 10.53 0.55 0.82 +12.0 % 835 41.5 0.90 10.13 10.13 10.13 0.39 0.92 +12.0 % 900 41.5 0.97 9.93 9.93 9.93 0.34 1.01 +12.0 % 1450 40.5 1.20 9.18 9.18 9.18 0.37 0.80 +12.0 % 1750 40.1 1.37 8.79 8.79 8.79 0.31 0.85 +12.0 % 1900 40.0 1.40 8.44 8.44 8.44 0.23 1.08 +12.0 % 2000 40.0 1.40 8.38 8.38 8.38 0.31 0.84 +12.0 % 2100 39.8 1.49 8.47 8.47 8.47 0.27 0.96 +12.0 % 2300 39.5 1.67 8.13 8.13 8.13 0.30 0.88 +12.0 % 2450 39.2 1.80 7.71 7.71 7.71 0.36 0.93 +12.0 % 2600 39.0 1.96 7.53 7.53 7.53 0.37 0.84 +12.0 % 3500 37.9 2.91 7.54 7.54 7.54 0.29 1.20 £#13.1 % 3700 37.7 3.12 7.38 7.38 7.38 0.24 1.20 +131 % 5250 35.9 4.71 5.62 5.62 5.62 0.40 1.80 +131 % 5600 35.5 5.07 5.16 5.16 5.16 0.40 1.80 £13.1 % 5750 35.4 5.22 5.32 5.32 5.32 0.40 1.80 +131 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—7472_Aug18 Page 5 of 39

EX3DV4— SN:7472 August 29, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7472 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth Unc f (MHz)° Permittivity® (S/m)" ConvFX ConvFY ConvFZ Aipha® _{mm) (k=2) 750 55.5 0.96 10.66 10.66 10.66 0.47 0.85 +12.0 % 835 55.2 0.97 10.35 10.35 10.35 0.34 0.98 +12.0 % 1640 53.7 1.42 8.94 8.94 8.94 0.36 0.84 +12.0 % 1750 53.4 1.49 8.42 8.42 8.42 0.34 0.99 +12.0 % 1900 53.3 1.52 8.07 8.07 8.07 0.41 0.90 +12.0 % 2300 52.9 1.81 8.11 8.11 8.11 0.43 0.88 +12.0 % 2450 52.7 1.95 7.84 7.84 7.84 0.37 1.02 +12.0 % 2600 52.5 216 7.70 7.70 7.70 0.24 1.05 +12.0 % 3500 51.3 3.31 7.23 7.23 7.23 0.27 1.25 #13.1 % 5250 48.9 5.36 4.90 4.90 4.90 0.50 1.90 £13.1 % 5600 48.5 5.77 4.37 4.37 4.37 0.50 1.90 *13.1 % 5750 48.3 5.94 4.56 4.56 4.56 0.50 1.90 +13.1 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%,. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. ° Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—7472_Aug18 Page 6 of 39

EX3DV4— SN:7472 August 29, 2018 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) Ti T3 Frequency response (normalized) Le] C*] R2 — [ul) < N Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—7472_Aug18 Page 7 of 39

EX3DV4— SN:7472 August 29, 2018 Receiving Pattern (¢), 9 = 0° f=600 MHz,TEM f=1800 MHz,R22 90 _ —_®_ —~ — * ~‘\*-‘_ « 135 r a © 45 135 — 45 4 5 # * = ® a & ~* * U + * # t * | * ® # * $ * * * ® * * + * \ * * U & 1 *~—<, * i I' & ** % + ; & & t /% * |I 18() # * o§«—t ® 180 * e [ ) * 02 04 0g .08 \ [ L* C 4Cor, os og ® Nes |0 t oo# , * J "reag._s | a + Pr * * *—<4——* Ad 1 i & + o% + * *o% / \ # a B x)\ h % * s * * m f * # * * * ® # / 2+ v w — * * * 235 . . y—* . 315 25~ * 15 + #o 20 e @ © t# ® 0 @ Tot X Y¥ Tot X Y Z Error [dB] 1 1 1 1 I L L 1 1 1 L 1 L | 1 Roll [7] 105%'-12 600 MHz 1800 MHz e 25%11le a Uncertainty of Axial Isotropy Assessment: + 0.5% (k=2) Certificate No: EX3—7472_Aug18 Page 8 of 39

EX3DV4— SN:7472 August 29, 2018 Dynamic Range f(SARneaq) (TEM cell , fey,= 1900 MHz) 104—— Input Signal [uV] 10° 10e ds $#EE 103 102 108 10° 10‘ 10 10° SAR [mW/icm3] not compensated compensated 2 I 1 P oo | keA J § 0 : i a : w a1 $— .9 ib ’ HIRAEHE h 1 4 [ f 103 102 101 100 102 108 8 SAR [mW/cm3] L* not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—7472_Aug18 Page 9 of 39

EX3DV4— SN:7472 August 29, 2018 Conversion Factor Assessment f= 835 MHz,WGLS RQ (H_convF) t= 1900 MHz,WGLS R22 (H_convF) ies § R 6 to in | oa } 0o *%l. 25| | % ; * * *> bo** 25 a 2 m|o * 3 s | * $ 20 € 3 s 0| 15 | x | 10 10 k. % % [ hat "# 6 ~ o 5— € *l *~ | *n n ig . x 00— . . i any 4A L., i4 i i_l g4 44— . i 1 0 § 10 15 20 25 30 35 40 0 10 15 2 25 30 35 40 z2 [mm} O2 z [mm] _a _8 _* analytical measured analytical measured Deviation from Isotropy in Liquid Error (6, 8), f = 900 MHz Deviation —1.0 —0.8 —0.6 —0.4 —0.2 0.0 0.2 0.4 0.6 0.8 1.0 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: EX3—7472_Aug18 Page 10 of 39


Document Created: 2019-06-06 14:50:18
Document Modified: 2019-06-06 14:50:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC