DFS Test Report

FCC ID: HD5-CN80L1N

Test Report

Download: PDF

FCCID_3783953

DFS Test Report

Report No.: RF171130C29-7

FCC ID: HD5-CN80L1N

Test Model: CN80L1N

Received Date: Dec. 04, 2017

Test Date: Jan. 02 to 03, 2018

Issued Date: Mar. 08, 2018

Applicant: Honeywell International Inc.

Address: 9680 Old Bailes Road, Fort Mill, SC 29707 USA

Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan
Branch Hsin Chu Laboratory
Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300,
Taiwan R.O.C.
Test Location : E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300,
Taiwan R.O.C.
FCC Registration /
723255 / TW2022
Designation Number:

This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific
mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report
must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.

Report No.: RF171130C29-7 Page No. 1 / 25 Report Format Version: 6.1.2

Table of Contents
Release Control Record .................................................................................................................................. 3
1 Certificate of Conformity ...................................................................................................................... 4
2 EUT Information .................................................................................................................................... 5
2.1 Operating Frequency Bands and Mode of EUT .................................................................................. 5
2.2 EUT Software and Firmware Version .................................................................................................. 5
2.3 Description of Available Antennas to the EUT .................................................................................... 6
2.4 EUT Maximum Conducted Power ....................................................................................................... 7
2.5 EUT Maximum EIRP Power ................................................................................................................ 8
2.6 Transmit Power Control (TPc) ............................................................................................................. 9
2.7 Statement of Maunfacturer .................................................................................................................. 9
3. U-NII DFS Rule Requirements ........................................................................................................... 10
3.1 Working Modes and Required Test Items ......................................................................................... 10
3.2 Test Limits and Radar Signal Parameters .......................................................................................... 11
4. Test & Support Equipment List ......................................................................................................... 14
4.1 Test Instruments ................................................................................................................................ 14
4.2 Description of Support Units ............................................................................................................. 14
5. Test Procedure .................................................................................................................................... 15
5.1 DFS Measurement System ............................................................................................................... 15
5.2 Calibration of DFS Detection Threshold Level .................................................................................. 16
5.3 Deviation From Test Standard ........................................................................................................... 17
5.4 Conducted Test Setup Configuration ................................................................................................ 17
5.4.1 Client without Radar Detection Mode ................................................................................................ 17
6. Test Results ......................................................................................................................................... 18
6.1 Summary of Test Results .................................................................................................................. 18
6.2 Test Results ....................................................................................................................................... 19
6.2.1 Test Mode: Device Operating In Client without Radar Detection Mode. ........................................... 19
6.2.2 Channel Closing Transmission and Channel Move Time .................................................................. 20
6.2.3 Non-Occupancy Period ..................................................................................................................... 21
6.2.4 Non-Associated Test.......................................................................................................................... 23
6.2.5 Non- Co-Channel Test ....................................................................................................................... 23
7. Information on the Testing Laboratories .......................................................................................... 24
8. Appendix-A .......................................................................................................................................... 25

Report No.: RF171130C29-7 Page No. 2 / 25 Report Format Version: 6.1.2

Release Control Record

Issue No. Description Date Issued
RF171130C29-7 Original release. Mar. 08, 2018

Report No.: RF171130C29-7 Page No. 3 / 25 Report Format Version: 6.1.2

2 EUT Information

2.1 Operating Frequency Bands and Mode of EUT
Table 1: Operating Frequency Bands and Mode of EUT

Operating Frequency Range
Operational Mode
5250~5350MHz 5470~5725MHz
Client without radar detection and ad
 
hoc function

2.2 EUT Software and Firmware Version
Table 2: The EUT Software/Firmware Version

No. Product Model No. Software/Firmware Version

V1.2.1.6.44.4.21+
1 Dolphin CN80 CN80L1N Jenkins-slave@ch3uu0005#1
Wed Dec 600:11:13 GMT 2017

Report No.: RF171130C29-7 Page No. 5 / 25 Report Format Version: 6.1.2

2.3 Description of Available Antennas to the EUT
Table 3: Antenna List
Radio 1
WLAN Antenna Spec. / Bluetooth Antenna No. 1 Spec.
Antenna Gain
Trace loss and
include trace loss Frequency range
Chain No. Antenna type Connector type cable loss
and cable loss (GHz)
(dB)
(dBi)
-0.38 2.4~2.4835 1.6
-0.39 5.15~5.25
Chain 0 -0.39 5.25~5.35 PIFA POGO pin
3
-0.39 5.47~5.725
-0.39 5.725~5.85
3.36 2.4~2.4835 0.6
3.46 5.15~5.25
Chain 1 3.46 5.25~5.35 PIFA POGO pin
1.2
3.46 5.47~5.725
3.46 5.725~5.85
WWAN Antenna Spec.
Antenna Gain
Trace loss
Chain No. include trace loss Frequency range Antenna type Connector type
(dB)
(dBi)
0.28 700~960MHz 0.4
1.15 1.70~2.0GHz 0.6
Chain 0 PIFA POGO pin
1.37 2.1~2.4GHz 0.8
1.02 2.4~2.7GHz 0.9
0.79 700~960MHz 0.4

Chain 1 -0.35 1.70~2.0GHz 0.6
PIFA POGO pin
(RX only) 1.05 2.1~2.4GHz 0.8
0.37 2.4~2.7GHz 0.9
Radio 2
Bluetooth Antenna No. 2 Spec. / Zigbee Antenna Spec.
Antenna Gain
Frequency range Trace loss
include trace loss Antenna type Connector type
(GHz) (dB)
(dBi)
-0.03 2.4~2.4835 PIFA POGO pin 0.8
Radio 3
NFC Antenna Spec.
Frequency range
Antenna type Connector type
(MHz)
13~14 Loop NA

Report No.: RF171130C29-7 Page No. 6 / 25 Report Format Version: 6.1.2

2.4 EUT Maximum Conducted Power
Table 4: The Measured Conducted Output Power
802.11a

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 85.076 19.3
5470~5725 84.831 19.29

802.11ac (VHT20)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 84.217 19.25
5470~5725 84.88 19.29

802.11ac (VHT40)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 85.083 19.30
5470~5725 85.088 19.30

802.11ac (VHT80)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 37.937 15.79
5470~5725 79.627 19.01

Report No.: RF171130C29-7 Page No. 7 / 25 Report Format Version: 6.1.2

2.5 EUT Maximum EIRP Power
Table 5: The EIRP Output Power List
802.11a

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 188.715 22.76
5470~5725 188.172 22.75

802.11ac (VHT20)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 186.81 22.71
5470~5725 188.281 22.75

802.11ac (VHT40)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 188.731 22.76
5470~5725 188.742 22.76

802.11ac (VHT80)

MAX. POWER
FREQUENCY BAND
(MHz) OUTPUT OUTPUT
POWER(mW) POWER(dBm)
5250~5350 84.152 19.25
5470~5725 176.628 22.47

Report No.: RF171130C29-7 Page No. 8 / 25 Report Format Version: 6.1.2

@
Eomcnts
venitas

2.6 Transmit Power Control (TPC)

U—NIl devices operating in the 5.25—5.35 GHz band and the 5.47—5.725 GHz band shall employ a TPC
mechanism. The U—NII device is required to have the capability to operate at least 6 dB below the mean EIRP
value of 30 dBm. A TPC mechanism is not required for systems with an e.i.r.p. of less than 500 mW.

Applicable EIRP ECC 15.407 (h)(1)

>500mW The TPC mechanism is required for system with an EIRP of
above 500mW

N <500mW The TPC mechanism is not required for system with an
EIRP of less 500mW

2.7 Statement of Maunfacturer

Manufacturer statement confirming that information regarding the parameters of the detected Radar
Waveforms is not available to the end user. And the device doesn‘t have Ad Hoc mode on DFS frequency
band.

Report No.: RF171130020—7 Page No. 9 / 25 Report Format Version: 6.1.2

3. U-NII DFS Rule Requirements
3.1 Working Modes and Required Test Items
The manufacturer shall state whether the UUT is capable of operating as a Master and/or a Client. If the UUT
is capable of operating in more than one operating mode then each operating mode shall be tested separately.
See tables 6 and 7 for the applicability of DFS requirements for each of the operational modes.

Table 6: Applicability of DFS Requirements Prior To Use a Channel
Operational Mode
Requirement Client without radar Client with radar
Master
detection detection
Non-Occupancy Period   note 
DFS Detection Threshold  Not required 
Channel Availability Check Time  Not required Not required
U-NII Detection Bandwidth  Not required 
Note: Regarding KDB 905462 D03 Client Without Radar Detection New Rules v01r02 section(b)(5/6),
If the client moves with the master, the device is considered compliant if nothing appears in the client
non-occupancy period test. For devices that shut down (rather than moving channels), no beacons
should appear. An analyzer plot that contains a single 30-minute sweep on the original channel.

Table 7: Applicability of DFS Requirements during Normal Operation.

Operational Mode
Requirement Master or Client with Client without radar
radar detection detection
DFS Detection Threshold  Not required
Channel Closing Transmission Time  
Channel Move Time  
U-NII Detection Bandwidth  Not required

Additional requirements for devices Master or Client with Client without radar
with multiple bandwidth modes radar detection detection
U-NII Detection Bandwidth and Statistical All BW modes must be
Not required
Performance Check tested
Channel Move Time and Channel Closing Test using widest BW Test using the widest BW
Transmission Time mode available mode available for the link
All other tests Any single BW mode Not required
Note: Frequencies selected for statistical performance check (Section 7.8.4) should include
several frequencies within the radar detection bandwidth and frequencies near the edge of
the radar detection bandwidth. For 802.11 devices it is suggested to select frequencies in
each of the bonded 20 MHz channels and the channel center frequency.

Report No.: RF171130C29-7 Page No. 10 / 25 Report Format Version: 6.1.2

3.2 Test Limits and Radar Signal Parameters
Detection Threshold Values

Table 8: DFS Detection Thresholds For Master Devices And Client Devices with Radar Detection
Value
Maximum Transmit Power
(See Notes 1, 2, and 3)
EIRP ≥ 200 milliwatt -64 dBm
EIRP < 200 milliwatt and
-62 dBm
power spectral density < 10 dBm/MHz
EIRP < 200 milliwatt that do not meet the
-64 dBm
power spectral density requirement
Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna.
Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the
test transmission waveforms to account for variations in measurement equipment. This will ensure
that the test signal is at or above the detection threshold level to trigger a DFS response.
Note3: EIRP is based on the highest antenna gain. For MIMO devices refer to KDB Publication
662911 D01.

Table 9: DFS Response Requirement Values

Parameter Value
Non-occupancy period Minimum 30 minutes
Channel Availability Check Time 60 seconds
10 seconds
Channel Move Time
See Note 1.
200 milliseconds + an aggregate of 60
Channel Closing Transmission Time milliseconds over remaining 10 second period.
See Notes 1 and 2.
Minimum 100% of the U-NII 99% transmission
U-NII Detection Bandwidth
power bandwidth. See Note 3
Note 1: Channel Move Time and the Channel Closing Transmission Time should be performed with
Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst.
Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the
beginning of the Channel Move Time plus any additional intermittent control signals required to
facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second
period. The aggregate duration of control signals will not count quiet periods in between
transmissions.
Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 should be used. For each
frequency step the minimum percentage of detection is 90 percent. Measurements are performed
with no data traffic.

Report No.: RF171130C29-7 Page No. 11 / 25 Report Format Version: 6.1.2

Parameters of DFS Test Signals

Step intervals of 0.1 microsecond for Pulse Width, 1 microsecond for PRI, 1 MHz for chirp width and 1 for the
number of pulses will be utilized for the random determination of specific test waveforms.

Table 10: Short Pulse Radar Test Waveforms

Minimum
Minimum
Radar Pulse Width PRI Number Percentage of
Number of
Type (µsec) (µsec) of Pulses Successful
Trials
Detection

0 1 1428 18 See Note 1 See Note 1
Test A: 15 unique
PRI values
randomly selected
from the list of 23
PRI values in
Table 5a 1 .
------------------------ Roundup 360
Test B: 15 unique
19 ∙ 10
6
PRI values
randomly selected PRIμ sec
1 1 within the range 60% 30
of 518-3066
μ sec, with a
minimum
increment of 1
μ sec,
excluding PRI
values
selected in
Test A
2 1-5 150-230 23-29 60% 30
3 6-10 200-500 16-18 60% 30
4 11-20 200-500 12-16 60% 30
Aggregate (Radar Types 1-4) 80% 120
Note 1: Short Pulse Radar Type 0 should be used for the detection bandwidth test,
channel move time, and channel closing time tests.

Report No.: RF171130C29-7 Page No. 12 / 25 Report Format Version: 6.1.2

Table 11: Long Pulse Radar Test Waveform
Minimum
Pulse Chirp Number of Minimum
Radar PRI Number of Percentage of
Width Width Pulses Per Number of
Type (µsec) Bursts Successful
(µsec) (MHz) Burst Trials
Detection
5 50-100 5-20 1000-2000 1-3 8-20 80% 30
Three subsets of trials will be performed with a minimum of ten trials per subset. The subset of trials differ in
where the Long Pulse Type 5 Signal is tuned in frequency.

a) the Channel center frequency
b) tuned frequencies such that 90% of the Long Pulse Type 5 frequency modulation is within the low edge of
the UUT Occupied Bandwidth
c) tuned frequencies such that 90% of the Long Pulse Type 5 frequency modulation is within the high edge of
the UUT Occupied Bandwidth

It include 10 trails for every subset, the formula as below,

For subset case 1: the center frequency of the signal generator will remain fixed at the center of the UUT
Channel.

For subset case 2: to retain 90% frequency overlap between the radar signal and the UUT Occupied
Bandwidth, the center frequency of the signal generator will vary for each of the ten trials in subset case 2.
The center frequency of the signal generator for each trial is calculated by:

+(0.4∗ ℎ ℎ[ ])

For subset case 3: to retain 90% frequency overlap between the radar signal and the UUT Occupied
Bandwidth, the center frequency of the signal generator will vary for each of the ten trials in subset case 3.
The center frequency of the signal generator for each trial is calculated by:

−(0.4∗ ℎ ℎ[ ])

Table 12: Frequency Hopping Radar Test Waveform

Hopping Minimum
Pulse Hopping Minimum
Radar PRI Pulses Sequence Percentage of
Width Rate Number of
Type (µsec) per Hop Length Successful
(µsec) (kHz) Trials
(msec) Detection

6 1 333 9 0.333 300 70% 30

Report No.: RF171130C29-7 Page No. 13 / 25 Report Format Version: 6.1.2

5.2 Calibration of DFS Detection Threshold Level

The measured channel is 5500 MHz in 20MHz Bandwidth, 5510MHz in 40MHz Bandwidth.
5530MHz in 80MHz Bandwidth. The radar signal was the same as transmitted channels, and
injected into the antenna port of AP (master) or Client Device with Radar Detection, measured the
channel closing transmission time and channel move time. The Master antenna gain is 3.428dBi and
required detection threshold is -59.572dBm (= -64 +1 +3.428). The calibrated conducted detection threshold
level is set to -59.572 dBm.

Conducted Setup Configuration of Calibration of DFS Detection Threshold Level

Control PC

Spectrum Radar Signal generate system
Analyzer

50Ω Load (Terminator)

Attenuator

C/S

50Ω Load Attenuator Attenuator C/S

(Terminator)

Report No.: RF171130C29-7 Page No. 16 / 25 Report Format Version: 6.1.2

5.3 Deviation From Test Standard
No deviation.

5.4 Conducted Test Setup Configuration

5.4.1 Client without Radar Detection Mode

Control PC

Spectrum Radar Signal generate system
Analyzer

Attenuator

C/S

Attenuator Attenuator C/S Master

Client (UUT) Notebook Notebook

The UUT is a U-NII Device operating in Client mode without radar detection. The radar test signals are
injected into the Master Device.

Report No.: RF171130C29-7 Page No. 17 / 25 Report Format Version: 6.1.2

6. Test Results

6.1 Summary of Test Results

CLAUSE TEST PARAMETER REMARKS PASS/FAIL

15.407 DFS Detection Threshold Not Applicable NA

15.407 Channel Availability Check Time Not Applicable NA

15.407 Channel Move Time Applicable Pass

15.407 Channel Closing Transmission Time Applicable Pass

15.407 Non- Occupancy Period Applicable Pass

15.407 U-NII Detection Bandwidth Not Applicable NA

15.407 Non-associated test Applicable Pass

15.407 Non-Co-Channel test Applicable Pass

Report No.: RF171130C29-7 Page No. 18 / 25 Report Format Version: 6.1.2

@
Eomcnts
venitas

6.2 Test Results

6.2.1 Test Mode: Device Operating in Client without Radar Detection Mode.

The radar test signals are injected into the Master Device.
This test was investigated for different bandwidth (20MHz > 40MHz and 80MHz).
The following plots was done on 80MHz as a representative

DFS Detection Threshold

The Required detection threshold is —59.572dBm (= —64 +1 +3.428).
The conducted radar burst level is set lower than —59.572d4Bm.

Center 5.530000000 GHz Span 0 Hz
Res BW 3.0 MHz #WBW 8.0 MHz Sweep 50.67 ms (40001 pts)

Radar Signal 0

Report No.: RF171130020—7 Page No. 19 / 25 Report Format Version: 6.1.2

6.2.2 Channel Closing Transmission and Channel Move Time

Radar Signal 0
802.11ac (VHT80)

Radar Signal

Noise Floor

NOTE: T1 denotes the start of Channel Move Time upon the end of the last Radar burst. T2
denotes the data transmission time of 200ms from T1. T4 denotes the 10 second from T1 to
observe the aggregate duration of transmissions.

Noise Floor

NOTE: An expanded plot for the device vacates the channel in the required 500ms.

Report No.: RF171130C29-7 Page No. 20 / 25 Report Format Version: 6.1.2

3). The device transmits one type of radar as specified in the DFS Order.

Radar 0 is used to test during DFS testing.

4) The test frequency has been monitored to ensure no transmission of any type has occurred for 30
minutes;
Note: If the client moves with the master, the device is considered compliant if nothing appears in the
client non-occupancy period test. For devices that shut down (rather than moving channels), no
beacons should appear;
5) An analyzer plot that contains a single 30-minute sweep on the original test frequency.

Injected into Radar

Traffic Signal

Report No.: RF171130C29-7 Page No. 22 / 25 Report Format Version: 6.1.2

im
Eomcnts
venitas

6.2.4 Non—Associated Test

Master was off.
During the 30 minutes observation time, The UUT did not make any transmissions in the DFS band after UUT
power up.
Non — Associated Test

Noise Floor
Hoise foor of medsurement gystem A

6.2.5 Non— Co—Channel Test

The UUT was investigated after radar was detected the channel and made sure no co—channel operation with
radars.

Report No.: RF171130020—7 Page No. 23 / 25 Report Format Version: 6.1.2

7. Information on the Testing Laboratories

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to
provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited
and approved according to ISO/IEC 17025.

If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab: Hsin Chu EMC/RF/Telecom Lab:
Tel: 886-2-26052180 Tel: 886-3-6668565
Fax: 886-2-26051924 Fax: 886-3-6668323

Hwa Ya EMC/RF/Safety Lab:
Tel: 886-3-3183232
Fax: 886-3-3270892

Email: service.adt@tw.bureauveritas.com
Web Site: www.bureauveritas-adt.com

The address and road map of all our labs can be found in our web site also.

Report No.: RF171130C29-7 Page No. 24 / 25 Report Format Version: 6.1.2

Document Created: 2018-03-16 11:20:32
Document Modified: 2018-03-16 11:20:32

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC