Exhibit D Users Manual per 2 1033 b3

FCC ID: HBW7644

Users Manual

Download: PDF
FCCID_1526421

MODEL 823LM REMOTE LIGHT SWITCH OVERVIEW The Remote Light Switch offers a convenient way to control the lights in your home. The To prevent possible SERIOUS INJURY or DEATH from Remote Light Switch is compatible with Switch electrocution or fire: Security✚ 2.0™ and MyQ™ products. The • Turn off power at the fuse box or circuit breaker BEFORE Remote Light Switch is compatible with up to proceeding. 8 Security✚ 2.0™ remote controls and a combination of up to 8 MyQ™ enabled garage • The light control is ONLY for indoor use. door openers or LiftMaster® Internet Gateway • Installation and wiring MUST be in compliance with ALL devices. This product is NOT recommended for local electrical and building codes. control of household appliances or fans. Not for use with 3-way or 4-way switch combinations. NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. LED This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to SPECIFICATIONS the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired Bulb Type: Compact fluorescent, incandescent, operation. or LED. AVIS : Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute Max Load Rating:. . . . . . . . . . . . . . . 300 Watts modification de ce récepteur. IL N’EXISTE AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Incandescent Lamp . . . . . . . . . . . . . 300 Watts Cover Learn Button Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de la norme Compact Fluorescent Lamp (CFL). . .2.5 Amps NOTE: The wall plate is IC RSS-210. Son utilisation est assujettie aux deux conditions suivantes : (1) ce dispositif ne peut causer des interférences nuisibles, et (2) ce dispositif doit accepter toute interférence reçue, Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 120 Vac not provided. y compris une interférence pouvant causer un fonctionnement non souhaité. CARTON INVENTORY Wire Nuts Screws (2) (1) (2) Remote Light Switch MODES OF OPERATION The remote light switch can be programmed to Security✚ 2.0™ remote controls, MyQ™ garage door openers, or LiftMaster® Internet Gateway devices. REMOTE CONTROL OPERATION: GARAGE DOOR OPENER OPERATION: INTERNET GATEWAY OPERATION: Allows you to activate the Allows you to synchronize Allows you to activate the remote light switch from a the remote light switch with remote light switch from a remote control. your garage door opener web browser (requires the light bulbs. Example: The internet gateway accessory garage door opener light model 828LM). bulbs are set to automatically turn off after 4 ½ minutes, the remote light switch will also turn off after 4 ½ minutes. 1

INSTALLATION BEFORE YOU BEGIN: This device REQUIRES a ground; if a ground is not available, contact a To prevent possible SERIOUS INJURY or DEATH from electrocution or qualified electrician. If you are not experienced and familiar with electrical fire: wiring and electrical codes, contact a qualified electrician. Some codes require installation by a qualified electrician. • Turn off power at the fuse box or circuit breaker BEFORE proceeding. NOTE: Install in accordance with all national and local codes. • The light control is ONLY for indoor use. 1. Disconnect power at the circuit breaker or fuse box BEFORE • Installation and wiring MUST be in compliance with ALL local proceeding. electrical and building codes. 2. Remove wall plate and set aside for re-assembly. REMOVE OLD WALL SWITCH: IMPORTANT NOTE: This illustration is only an example and your application and wiring may look different. 1. Remove switch from switch box. Figure 1 2. During to removal, identify or label the load and line wires. Inside of NOTE: Typically a line wire is the incoming hot wire from the circuit cable Load breaker. The load wire is the wire supplying power between the switch and the light. Line 3. Keep load wires separated from line wire. Ground INSTALL NEW SWITCH: Green Wires 1. Identify the antenna routing (Figure 2). (Ground) Figure 2 Junction Green Box Wire Screws Load Wire For optimal range fully extend the antenna. Feed antenna wire between a Line gap between the switch box and drywall. Wire Black Red Wire Wire 2. Connect the wires (Figure 3). Remote Light • Green wire to ground. Switch Connect the green wire on the new switch to the exposed copper Cover ground, green wire, or to the ground connection within metal switch box. (NOTE: If ground doesn’t exist contact an electrician to add a ground. This product will not function without a proper Wall Plate Yellow Antenna ground.) Screws (not provided) (existing-not • Red wire to load. provided) • Black wire to line. Figure 3 3. Secure connections with a wire nut and wrap each wire nut with electrical tape. Black Wire NOTE: Turn all wire nuts clockwise, making sure the bare wires are Line covered. Tug on each wire nut to make sure the connections are good. 4. Carefully pack the wiring back into switch box. Make sure the wires are not pinched or strained. Make sure the antenna is hanging straight Red Wire down between the switch box and the drywall. Load 5. Fasten the remote light switch to switch box with the screws (provided). Green Wire 6. Fasten the wall plate securely over the switch box with the original Ground screws from the wall plate. 7. Turn on the power to circuit at fuse box or circuit breaker. 8. Test the light switch, manually press the light switch to ensure the light is functional. If it is not functional, see Troubleshooting. 9. Open the cover on the light switch so you can view the LED. 10.Allow up to 10 minutes for remote light switch to power up properly, when the LED stops flashing (up to 10 minutes) proceed to Programming. 2

PROGRAMMING IMPORTANT NOTE: Allow 10 minutes for remote light switch to power up properly, prior to proceeding to Programming. 1 Press and HOLD the Press the Learn button on Visit www.myliftmaster.com. 2 remote control OR the garage door opener. OR Go to “Manage Devices”, then button. “Learn Device” to program to the internet gateway accessory. Lift the cover on the remote light switch to access the “LEARN” button. 3 NOTE: If the remote control button is not held down until the remote light switch LED Then press and release the “LEARN” button. flashes, the code has not been accepted. The LED will FLASH once. Programming is complete. NOTE: If needed, press and hold the “LEARN” button with a narrow instrument. TO ERASE ALL CODES FROM MEMORY 1 Press and HOLD the “LEARN” button until the LED goes out (approximately 6 seconds). All codes are now erased. TESTING 1 Press the switch to the Press the switch to the 2 Press remote control Press again and the light ON position. The light OFF position. The light button. The light should should turn off. should turn on. should turn off. turn on. Test the remote control operation at various locations within your home for convenience and range. The remote control range will vary depending on your house and wiring construction. The range may be reduced by metal lath, foil-backed insulation or aluminum siding. 3

TROUBLESHOOTING If the light does not operate, check to be sure: To avoid electric shock, press the switch to the OFF position • The power is ON. Check the fuse box or circuit breaker. when changing the light bulb. • The device is properly grounded. • The light bulb is “good”. • The switch is in the ON position. • The electrical wiring is correct. Review the wiring instructions. • You are pressing the remote control button selected to operate the light control. • The remote control has power. NOTE: The test light on the remote control should glow when the button is pressed, if not replace the battery. © 2011, The Chamberlain Group, Inc. 114A4349 All Rights Reserved


Document Created: 2011-08-10 15:57:45
Document Modified: 2011-08-10 15:57:45
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC