User Manual Part 2

FCC ID: HBW7545

Users Manual

Download: PDF
FCCID_1627639

WIRING WIRE THE OPERATOR TO THE CONTROL BOARD WIRE THE OPERATOR ARM TO THE CONTROL BOARD 1 Insert the operator cable through the watertight connector mounted in the bottom of the control box. 2 Extend the operator cable and wires to the Gate 1 connector and connect as shown. 3 Tighten watertight connector nut. S LAR / HARGER BR GRN WHT YEL BLU RE BR RN WHT YEL BLU RE + - GATE 2 GATE 1 ! If installing one operator, proceed to page 22. If installing two operators, continue to the next page. 19

WIRING DUAL GATES ONLY DUAL GATES ONLY INSTALL THE EXTENSION CABLE AND JUNCTION BOX Before digging, contact local underground utility locating companies. The following items are required to complete the junction box installation: • 4 x 4 Junction Box with 3/4" NPT threaded port holes • Screws • PVC Conduit Junction Box Trench across driveway to bury the extension cable. Use PVC conduit to 1 prevent damage to cables. Extension Cable Operator Cable 2 Open the junction box by removing screws (4) and set aside. 3 Mount the junction box within 3 feet (0.9 m) of second operator. 4 Route operator cable and extension cable through watertight connector nut and watertight connector. ! ! Within 5 Insert cables and watertight connectors into the holes in the bottom of the junction box (not provided). 3 feet 6 Feed extension cable through PVC conduit and secure with nut. PVC Conduit WIRE THE EXTENSION CABLE TO THE SECONDARY OPERATOR 1 Insert wires from extension cable and operator cable into the terminal block connector as shown (like-colored wires must face each other). 2 Put wires inside of junction box. 3 Secure operator and extension cables with watertight connector nut. 4 Reinstall cover. Terminal Block Connector Extension Cable Operator Cable 20

WIRING DUAL GATES ONLY DUAL GATES ONLY WIRE THE EXTENSION CABLE TO THE CONTROL BOARD 1 Choose a knockout in the bottom of the control box. 2 Insert a watertight connector through the knockout and tighten with nut. Extension Cable 3 Insert the extension cable through watertight connector. BRO GRN HT YEL BLU RED BRO GRN WHT YEL BLU RED SOLAR / CHARGER + GATE 2 GATE 1 4 Extend the cable and wires to Gate 2 connector on the control board. Connect wires as shown. 5 Tighten the watertight connector nut to secure extension cable to control box. ! ! SET THE BIPART DELAY Occasionally in dual gate installations, one gate will need to open first and close second. This would happen if there was an ornamental overhang on one gate or OUTSIDE PROPERTY if using a solenoid lock, for example. This gate is called the Primary gate and needs to be connected to Gate 1 connections on the control board. Thus, it is preferred that the control box be installed on the same side as this gate. If there is no appropriate location on that side for the control box, then mount the Primary Gate control box on the opposite side, but connect the operator closest to the control box to the Gate 2 connector and the operator on the opposite side to the Gate 1 connector. Primary Gate - Connect to Gate 1 Connector on Control Board. NOTE: The gate with the longer travel span (opening) must be set as the primary gate (GATE 1). 1 The BIPART DELAY switch on the control board needs to be set to the ON position. BIPART L SET OPEN SET C OSE M T ER LOSE O O F ON R S& L A E T B GN MIT ( E ON S) 10 DELAY The following illustration shows a dual gate configuration with a decorative SE MO E G TE 2 5 0 STOP EX T F 80 NP T POWER MER B TT L W I GNOS I STATUS overlapping piece on the outside of the gate. B TT C ARG NG ATE M V NG ACC WR VL CO ES S AD W C OSE E NTE RUP + OFF ON + If a solenoid lock is being used on a gate, the gate with the lock attached to it TIMER J5 is the primary gate. NC M 15 LOCK NO + + AC ESS RY SW A T DC POW R OWER + ON + B ARD XP OL R / HAR ER BR GRN WT E B U ED BR GRN WT E LU R D + ID R SET AL RM 21

WIRING POWER WIRING POWER WIRING NUMBER OF CYCLES PER DAY This operator can be wired for either 120 Vac or a solar panel (not Swing Gate Installation (6 ft. 1200 lb. gate/ 19 ft. 500 lb. gate) provided). Follow the directions according to your application. For dual CONFIGURATION SINGLE GATE DUAL GATE gate applications, power will have to be connected to each operator. 7AH 33AH Batteries 7AH 33AH Batteries Solenoid Lock Main power supply and control wiring MUST be run in separate Batteries (optional for Batteries (optional for conduits. 100 mA 300 mA (standard) Large Metal (standard) Large Metal 50 mA Control Box) Control Box) TOROID Continuous Continuous Continuous Continuous AMERICAN WIRE MAXIMUM WIRE MAXIMUM WIRE POWERED ✔ Continuous Continuous 2059 2056 GAUGE (AWG) LENGTH (120 VAC) LENGTH (240 VAC) ✔ Continuous Continuous Continuous Continuous 14 130 feet 260 feet ✔ Continuous Continuous Continuous Continuous ✔ Continuous Continuous Continuous Continuous 12 205 feet 410 feet BATTERY 215 1202 98 612 10 325 feet 650 feet POWERED ✔ 122 763 71 443 ✔ 207 1292 96 600 8 520 feet 1040 feet ✔ 200 1249 94 590 6 825 feet 1650 feet ✔ 178 1111 88 554 TRANSFORMER 1726 1720 1347 1340 4 1312 feet 2624 feet POWERED ✔ 1359 1352 1147 1140 NOTE: Use copper conductors ONLY. ✔ 1670 1663 1301 1293 ✔ 1615 1607 1257 1248 ✔ 1391 1380 1075 1064 120 VAC STANDARD CONTROL BOX 1 Turn off the AC power from the main power source circuit breaker. 2 Run the AC power wires to the control box. 3 Remove the junction box cover. 4 Connect the green wire to the earth ground rod wire using a wire nut. 5 Connect the white wire to NEUTRAL using a wire nut. 6 Connect the black wire to HOT using a wire nut. Junction Box Cover 7 Replace the junction box cover. Ensure the wires are not pinched. LARGE METAL CONTROL BOX (XLM) Junction 22 Box Cover

WIRING POWER WIRING + CONNECT BATTERIES POWER WIRING CONTINUED... NUMBER OF CYCLES PER DAY (SOLAR) Swing Gate Installation (6 ft. 1200 lb. gate/19 ft. 500 lb.) SOLAR PANEL(S) Single Gate NOT PROVIDED. SEE ACCESSORIES. CONFIGURATION ZONE 1 ZONE 2 ZONE 3 (6 Hrs (4 Hrs (2 Hrs The solar panel(s) must be located in an open area clear of obstructions and shading sunlight/day) Sunlight/day) Sunlight/ for the entire day. The gate operator is not supported in northern climates where day) temperatures reach below -4˚F. This is due to cold weather and a reduced number of 33AH Batteries (optional) 33AH Batteries (optional) 33AH Batteries (optional) 7AH Batteries (standard) 7AH Batteries (standard) 7AH Batteries (standard) hours of sunlight during the winter months. Cycle rate may vary from solar chart for areas that reach below 32˚F. Solar panels should be cleaned on a regular basis for Expansion Board 1 Loop (LD7LP) best performance to ensure proper operation. For solar applications, a minimum of High Band Low Band two 10W solar panels in series and two 7AH batteries are recommended. For Zone 3 cold weather sites, two 33AH batteries are recommended (for Large Metal Control Box (XLM) ONLY). We recommend LiftMaster low power draw accessories to minimize 120 154 76 96 33 38 20W SOLAR PANEL power draw, refer to accessory page. ✔ 117 151 74 93 30 35 NOTE: 20W would be two 10W ✔ ✔ 111 144 68 87 25 29 1 Locate the solar/charge plug on the control board and remove the transformer (12V) panels in series. ✔ ✔ 109 142 66 84 23 27 wires from the plug. ✔ ✔ ✔ ✔ 99 131 56 74 13 17 40W SOLAR PANEL 156 202 101 128 45 54 2 Connect the red (+) wire from the solar panel to the solar/charge plug (+). NOTE: 40W would be two 20W panels in series. ✔ ✔ ✔ 154 148 199 193 98 92 125 119 42 37 51 45 ✔ ✔ 145 190 90 117 35 43 3 Connect the black (-) wire from the solar panel to the solar/charge plug (-). ✔ ✔ ✔ ✔ 135 179 80 106 25 33 Dual Gates 4 Plug in the solar/charge plug. 20W SOLAR PANEL NOTE: 20W would be two 10W ✔ 54 53 69 68 34 33 43 42 15 13 17 16 (12V) panels in series. ✔ ✔ 50 65 31 39 11 13 ✔ ✔ 49 64 30 38 10 12 + ✔ ✔ ✔ ✔ 45 60 25 33 6 7 - 40W SOLAR PANEL 71 92 46 58 20 24 J5 ✔ 70 90 44 57 19 23 NOTE: 40W would be two 20W 67 87 42 54 16 20 J15 LOCK + - - + panels in series. ✔ ✔ SW. - ACCESSORY BATT DC 66 86 41 53 16 19 POWER POWER ✔ ✔ + ON ✔ ✔ ✔ ✔ 62 81 36 48 11 15 CL S 2 S PP Y 24 O TS EXP. BOAR SOLAR / CHARGER GROUND BR GRN WT YE BLU RED BR GRN WT YE BLU RED + ID RESET ALARM 3 NOT AVAILABLE Black Red NOT AVAILABLE (to solar panel) 2 3 1 2 1 1 CONNECT BATTERIES The batteries are charged in the circuit by the transformer or solar panel. STANDARD CONTROL BOX Battery 1 Turn OFF AC power to the operator at the circuit breaker. Connector 2 J15 Plug Plug the battery connector to the J15 plug labeled BATT(-)(+) DC(-)(+) on the control board. The control board will power up. 3 Turn ON AC power to the operator. 23

WIRING CONNECT BATTERIES + ENGAGE THE OPERATOR CONNECT BATTERIES The batteries are charged in the circuit by the transformer or solar panel. LARGE METAL CONTROL BOX (XLM) 7AH BATTERIES 1 Turn OFF AC power to the operator at the circuit breaker and unplug the transformer. 2 Battery Unplug the battery connector to the J15 plug labeled BATT(-)(+) DC(-)(+) on Connector the control board by squeezing the plug and pulling it from the control board. J15 Plug Connect a jumper between the positive (+) terminal of one battery to the 3 negative (-) terminal of the other battery. Jumper Black Wire Red Wire Connect the red wire from the J15 plug labeled BATT (+) to the positive (+) 4 terminal of the battery. Connect the black wire from the J15 plug labeled BATT (-) to the negative (-) 5 terminal of the battery. 6 Plug the J15 plug into the control board. The control board will power up. 7 Plug the transformer in. 8 Turn ON AC power. 33AH BATTERIES 33AH batteries can be used in place of the 7AH batteries for a Large Metal Control Box (XLM) solar application ONLY. A wall or column mount installation is recommended when using the 33AH batteries. ENGAGE THE OPERATOR 1 Turn the release lever clockwise 180°. This engages the motor. 2 Turn the key clockwise 180°. This locks the release lever. The operator is now engaged. 24

ADJUSTMENT LIMIT AND FORCE ADJUSTMENT LIMIT AND FORCE ADJUSTMENT To reduce the risk of SEVERE INJURY or DEATH: • Without a properly installed safety reversal system, persons (particularly small • NEVER use force adjustments to compensate for a binding or sticking gate. children) could be SERIOUSLY INJURED or KILLED by a moving gate. • If one control (force or travel limits) is adjusted, the other control may also • Too much force on gate will interfere with proper operation of safety reversal need adjustment. system. • After ANY adjustments are made, the safety reversal system MUST be tested. • NEVER increase force beyond minimum amount required to move gate. Gate MUST reverse on contact with a rigid object. INTRODUCTION Your operator is designed with electronic controls to make travel limit and force LIMIT SETUP LEDS adjustments easy. The adjustments allow you to program where the gate will stop in SET OPEN SET CLOSE OPERATOR MODE EXPLANATION the open and close position. The electronic controls sense the amount of force LED LED required to open and close the gate. The force is adjusted automatically when you BLINKING BLINKING NORMAL MODE Limits are not set. program the limits but should be fine tuned using the REVERSAL FORCE dial on the control board (refer to Fine Tune the Force section) to compensate for environmental OFF OFF NORMAL MODE Limits are set. changes. BLINKING BLINKING LIMIT SETTING MODE Limits are not set. The limits can be set using the control board (below) or a remote control (refer to BLINKING ON LIMIT SETTING MODE Open limit is not set. Limit Setup with a Remote Control in the Additional Features section). Setting the limits with a remote control requires a 3-button remote control programmed to ON BLINKING LIMIT SETTING MODE Close limit is not set. OPEN, CLOSE, and STOP. ON ON LIMIT SETTING MODE Limits are set. INITIAL LIMITS AND FORCE ADJUSTMENT For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force. 1 2 3 O TI 1 Set the GATE switch to the 1 position. PRESS & RELEASE TO CL TO BEG N (SECOND SET OPEN SET CLOSE LIMIT 10 SETUP 1 PR 2 REL Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter GATE 2 5 O TO BEG LIMI SETUP limit setting mode. OFF MOVE GATE 1 INPUT POWER TIM 2 ARGIN GAT 3 Press and hold the MOVE GATE buttons to move the gate to the open or close 4 SET OPEN SET CLOSE T R OPEN ORK OFF ON limit. INPU R L A E US: C OSE OB GN S L MIT 10 IRE S TUP DEPT MOVE 1 GATE 2 5 60 STOP OF 80 STATUS NPUT POWER ATT LOW D AGNOST CODES SET OPEN SET CLOSE BIP 4 ATT CHARG NG G TE MOV NG CC PWR OVL SH DOW CLO E DEL Press and release the SET CLOSE or SET OPEN button depending on which limit INT RR is being set. + OFF J5 PRESS & RELEASE NC 5 15 OCK TO BEG NO Press and hold the MOVE GATE button to move the gate to the other limit. + + CCESSORY SW B TT DC POWER POWER 5 + P N REL + TO BE LIMI OARD EXP SETUP 6 SOLAR / MOVE Press and release the SET CLOSE or SET OPEN button depending on which limit CHARGER G OUND R GRN WT E BLU R D R GRN WT YE BLU ED + 1 GATE 2 is being set. GAT SET OPEN SET CLOSE BI DEL INPU 7 TUS: Cycle the gate open and close. This automatically sets the force. 6 ! OFF it OP lim PRESS & O SE EN RELEASE When limits are set properly the operator will automatically exit limit setting mode. CL lim it TO BEG DUAL GATES: Set the GATE switch to the 2 position and repeat steps 2-7 for the secondary gate. 7 25

ADJUSTMENT LIMIT AND FORCE ADJUSTMENT + OBSTRUCTION TEST FINE TUNE THE FORCE The FORCE DIAL on the control board is used for fine tuning the force in cases where wind or environmental changes may affect the gate travel. TEST 1 BUTTONS Based on the length and weight of the gate it may be necessary to make additional TTER OPEN TWORK force adjustments. The force setting should be high enough that the gate will not RSAL CE reverse by itself nor cause nuisance interruptions, but low enough to prevent serious CLOSE injury to a person. The force setting is the same for both the open and close gate S T O EN S T LOSE X I ER N T O K O F ON directions. 2 S O S C N S) MT 10 S STOP MOVE 1 GATE 2 5 6 1 FF 18 MN M T S ATUS A T C AR I G A E M V NG A C PWR O L H Open and close the gate with the TEST BUTTONS. C OS Y S NETWORK REVERSAL 5 FORCE 2 15 If the gate stops or reverses before reaching the fully open or closed position, Y W B TT DC OW R P WER N C increase the force by turning the force control slightly clockwise. OA D EXP OL R / C A GER BR G N WT E LU R D BR G N WT YE B U ED D R S T L RM 60 3 MIN MAX Perform the “Obstruction Test” after every force setting adjustment (see BATT LOW below). WR ADJUST THE LIMITS If the limits have already been set the operator will exit the limit setting mode after resetting each limit. Each limit is set separately by following steps 1-3 of the Initial Limit and Force Adjustment section. ERASE LIMITS 1 To erase the limits, press and hold the SET OPEN and SET CLOSE buttons simultaneously (5 seconds) until both the SET OPEN and SET CLOSE LEDs blink ER OPEN K FF N S C CLO E LMT 0 F RE MOVE rapidly and the operator beeps. B GATE SET OPEN SET CLOSE 2 STOP I D P T PO ER A T OW I GN S I S ATUS C DES TT HA G N AT MO I G CC WR O L S L SE E E / I T RR 2 F Release the buttons and the SET OPEN and SET CLOSE LEDs will blink slowly 5 5 O indicating the limits will need to be set. A CE S RY SW B TT C OW R P WER ON XP SO AR / CH R ER R UND D R S T L RM OBSTRUCTION TEST The operator is equipped with an automatic obstruction sensing feature. If the gate 1 TTER TEST BUTTONS OPEN ETWORK S T O EN ET L SE encounters an obstruction during motion, the operator will automatically reverse FF O P N RSAL C O E 0 I E OVE A E 5 CE direction of the gate for a short time and then stop the gate. After any adjustments T P CLOSE N UT O ER I ER A T OW A N S I S AT S O ES B T C A GN A EM V G CC WR V H O E T R are made, test the operator: STOP 1 Open and close the gate with the TEST BUTTONS, ensuring that the gate is J 5 W TT WER O W O stopping at the proper open and close limit positions. O O AR / H RG R BR R WT E B U ED BR N WT E B U ED 2 2 Place a solid object between the open gate and a rigid structure. Ensure that the gate, the solid object, and the rigid structure can withstand the forces ! generated during this obstruction test. im it OP El EN OS CL lim it 3 Run the gate in the close direction. The gate should stop and reverse upon contact with the solid object. If the gate does not reverse off the solid object, reduce the force setting by turning the force control slightly counter-clockwise. The gate should have enough force to reach both the open and close limits, but MUST reverse after contact with a solid object. 3 ! 4 Repeat the test for the open direction. 26

PROGRAMMING REMOTE CONTROLS + ERASE ALL CODES REMOTE CONTROLS A total of 50 Security✚ 2.0™ remote controls and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. NOTE: When the memory is full the operator will exit programming mode and the remote control/keyless entry will not be programmed. The memory will need to be erased before programming any additional remote controls/keyless entries. If installing an 86LM to extend the range of the remote controls DO NOT bend the antenna. TO ADD OR REPROGRAM A REMOTE CONTROL (NOT PROVIDED) 1 1 LEARN Press and release the LEARN button (operator will beep and green XMITTER LED BU will light). XMITTER 2 Press the remote control button for the desired function. The operator will NETWORK SAL 2 automatically exit learn mode (operator will beep and green XMITTER LED will S T OP N ET LO E O F ON go out) if programming is successful. 0 FR D OVE A E 2 5 0 P T O ER T ER T L W D G O T T T S C D S T C A GN G T M VN C WR O D S A C S E N E R This programming step will program a single button as an open, close, and stop. To program additional Security✚ 2.0™ remote controls, repeat the steps until all the 5 L W A T C O ER O remote controls are programmed. W O O S L R/ C A G R R U D BR R WT E B U R D BR R WT YE UR D D E ET L RM PROGRAM OPEN ONLY ON A 1-BUTTON REMOTE CONTROL 1 LEARN 1 Press and release the LEARN button (operator will beep and green XMITTER LED BU 2 3 XMITTER will light). N NETWORK 2 Press the OPEN button. ET OP N S T CLO E M T R SAL TTER TEST BUTTONS 3 TW R OPEN TWORK OFF ON N Press the remote control button. The operator will automatically exit learn LMT LO E 0 I E S UP E T MO E RSAL OP G TE 2 5 6 ST P TA US O F 1 0 MN M X C DES RCE mode (operator will beep and green XMITTER LED will go out) if programming A T HA G NG H D W CLOSE A E MO NG CC P R O L C OS NT R is successful. 5 STOP J 5 OC To program additional Security✚ 2.0™ remote controls, repeat the steps until all the Y W B TT DC OW R OW R N C remote controls are programmed. B A D XP S L R/ C A GER G OU D R G N WT E U ED BR G N WT E L R D D R S T L RM PROGRAM OPEN, STOP, AND CLOSE ON A 3-BUTTON REMOTE CONTROL 1 Press and release the LEARN button (operator will beep and green XMITTER LED will light). 1 LEARN 2 BU 2 XMITTER Press the OPEN, CLOSE, or STOP button for the desired function. N NETWORK SAL TEST BUTTONS 3 3 TTER Press the remote control button for the desired function. The operator will OPEN SET PEN SET L SE ETWORK MT R automatically exit learn mode (operator will beep and green XMITTER LED will R RSAL O F N S C RCE L IT 0 S UP M VE 1 O E G TE 2 5 6 CLOSE go out) if programming is successful. N U PO ER T ER A T OW I G O T T TU : OD S A TC A GN G T MO NG C PW OV H C O E Y S N ER To program additional buttons or Security✚ 2.0™ remote controls, repeat the steps STOP until all the buttons or remote controls are programmed. J 5 O K W B T DC R P W R OW R CC O O R S L R/ ERASE ALL CODES C A GER G O ND BR RN T E U R D R G N WT E U ED M 1 Press and release the LEARN button (operator will beep and green XMITTER LED will light). LEARN 2 BU Press and hold the LEARN button again until the green XMITTER LED goes out XMITTER (approximately 6 seconds). All remote control codes are now erased. NETWORK SAL NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE S T OP N ET C O E O F ON NO USER SERVICEABLE PARTS. OVE A E S 2 5 0 0 D P This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may X F 0 N D T T S C D S T C A GN G T M VN CP RO D S A O E E not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired N E R operation. This Class B digital apparatus complies with Canadian ICES-003. 5 L W A T O ER O W O AVIS : Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modification de ce récepteur. IL N’EXISTE O AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. S L R/ C A G R BR R WT E B U R D BR R WT YE UR D D E ET L RM Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de la norme IC RSS-210. Son utilisation est assujettie aux deux conditions suivantes : (1) ce dispositif ne peut causer des interférences nuisibles, et (2) ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer un fonctionnement non souhaité. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 27

OPERATION MANUAL RELEASE + RESET BUTTON + REMOTE CONTROL + PARTY MODE MANUAL RELEASE In case of a power failure, the operator can be disengaged from the gate. With an operator, the release action may sometimes feel stiff/jerky, which is normal and has no effect on function. RELEASE 1 Insert the key into the lock. 2 Turn the key counter-clockwise 180°. 3 Turn the release lever counter-clockwise 180°. Operator is in manual mode and the gate can be opened and closed manually. ENGAGE 1 Turn the release lever clockwise 180°. This engages the motor. 2 Turn the key clockwise 180°. This locks the release lever. 3 Remove the key and store in a safe place. The operator is now engaged. RESET BUTTON The reset button is located on the side of the control box and serves several functions. ! Pressing the reset button will stop a moving gate during a normal open/close cycle, like a stop button. The operator does not need to be reset after doing this. PROGRAMMING LIMITS RESET If a mistake is made while programming the limits press the reset button to start over. A OPERATOR ALARM B If a contact sensor detects an obstruction twice consecutively the alarm will sound ! (up to 5 minutes) and the operator will need to be reset. When the inherent force of the operator (RPM/current sensor) detects the following (twice consecutively) the alarm will sound (up to 5 minutes) and the C D operator will need to be reset: A. The operator arm or gate is incorrectly installed. ! B. The gate does not meet specifications. ! C. Gate hinges are too tight or broken and the gate is not moving freely. D. The gate is moving and a car pushes the gate. E F E. A foreign object is on the gate frame while the gate is moving. F. The gate hits the driveway, curb or other, and gets stuck or bent in an ! ! awkward position. Remove any obstructions. Press the reset button to shut off the alarm and reset the operator. After the operator is reset, normal functions will resume. The operator alarm will beep 3 times with a command if the battery is low. REMOTE CONTROL PARTY MODE Once the remote control has been programmed the operator will operate as follows: If the Timer-to-Close feature is enabled and you would like the gate to remain open, When gate is in the closed position, activation of the remote control button will open open the gate fully, then press the reset button. The next command given by a the gate. During the open cycle another activation of the remote control will stop the LiftMaster remote control or SINGLE BUTTON on the control board will close the gate gate and the next activation of the remote control will close the gate. and return the operator to normal operation. When the gate is in the open position, activation of the remote control button will NOTE: If an alternative radio receiver is wired to the operator, the receiver must be close the gate. If the remote control is activated while the gate is closing, the gate will wired to the SINGLE BUTTON and CTRL PWR inputs. stop and the next activation will open the gate. 28

MAINTENANCE MAINTENANCE CHART + BATTERIES MAINTENANCE CHART Disconnect all power (AC, solar, battery) to the operator before servicing. The operator's AC Power switch ONLY turns off AC power to the control board and DOES NOT turn off battery power. ALWAYS disconnect the batteries to service the operator. DESCRIPTION TASK CHECK AT LEAST ONCE EVERY MONTH 6 MONTHS 3 YEARS Entrapment Protection Devices Check and test for proper operation X Warning Signs Make sure they are present X Manual Release Check and test for proper operation X Gate Inspect for wear or damage X Accessories Check all for proper operation X Electrical Inspect all wire connections X Mounting Hardware Check for tightness X Operator Inspect for wear or damage X Batteries Replace X NOTES: • Severe or high cycle usage will require more frequent maintenance checks. • It is suggested that while at the site voltage readings be taken at the operator. Using a digital voltmeter, verify that the incoming voltage to the operator it is within ten percent of the operator’s rating. BATTERIES Batteries will degrade over time depending on temperature and usage. For best performance, the batteries should be replaced every 3 years. Use only LiftMaster part 29-NP712 for replacement batteries. The operator comes with two 7AH batteries. Two 33AH (A12330SGLPK) may be used in place of the 7AH batteries for a Large Metal Control Box solar installation. A Battery tray (Model K10-36183) is required for the 33AH application. The batteries contain lead and need to be disposed of properly. Batteries do not perform well in extremely cold temperatures. The operator alarm will beep 3 times with a command if the battery is low. 29

ADDITIONAL FEATURES CONTROL BOARD OVERVIEW CONTROL BOARD OVERVIEW SET OPEN Button The SET OPEN button sets the OPEN limit. See Adjust Limits section. SET CLOSE Button The SET CLOSE button sets the CLOSE limit. See Adjust Limits section. MOVE GATE Button The MOVE GATE buttons will either open or close the gate when the operator is in Limit setting mode. See Adjust Limits section. BIPART DELAY Switch The Bipart delay switch is used only for dual gates. See Bipart Delay section. LEARN Button The LEARN button is for programming remote controls and the network. TIMER-TO-CLOSE dial The TIMER-TO-CLOSE (TTC) dial can be set to automatically close the gate after a specified time period. The TTC is factory set to OFF. If the TTC is set to the OFF position, then the gate will remain open until the operator receives another command from a control. Rotate the TIMER-TO-CLOSE dial to the desired setting. The range is 0 to 180 seconds, 0 seconds is OFF. NOTE: Any radio command, single button control, or CLOSE command on the control board prior to the TTC expiring will close the gate. The TTC is reset by any signals from the open controls, loops, close edges, and close photoelectric sensors (IR’s). REVERSAL FORCE dial The REVERSAL FORCE dial adjusts the force. See Force Adjustment section. TEST BUTTONS The TEST BUTTONS will operate the gate (OPEN, STOP and CLOSE). STATUS LEDs The STATUS LEDs are diagnostic codes for the operator. See Status LED Chart in the Troubleshooting section. SET OPEN SET CLOSE Open XMITTER Close A 3 Button B OPEN NETWORK OFF ON SBC Stop Station PRESS & RELEASE Com C CLOSE TO BEGIN Fire Dept (SECONDS) LIMIT 10 “FIRE D SETUP DEPT ” Fire Dept. MOVE 1 OPEN Com GATE 2 5 60 Exit STOP OFF 180 MIN EXIT Com E Exit Loop MAX Shadow F INPUT POWER TIMER BATT LOW DIAGNOSTIC STATUS: Shadow Loop BATT CHARGING GATE MOVING ACC PWR OVLD CODES SHADOW Com CLOSE EYES/ Interrupt G - INTERRUPT Com Interrupt Loop + Open (+) Open Direction Open (-) H Safety Close (+) Close Direction I + Close (-) Safety - Comm Link Data A Comm Link Data B J Comm Link J5 Lock N.C. (Maglock) K N.C. Mag and Com Solenoid Lock N.O. COM J15 LOCK Lock N.O. (Solenoid) L Com (-) Acc. Power M + + Switched ON with gate motion. Always ON with SW. - ACCESSORY BATT DC AccPower +24 Vdc POWER expansion board connected. Switches Off to save POWER + Com (-) battery power if expansion board disconnected. AccPower +24 Vdc N - ON Always ON + CLASS 2 SUPPLY 24 VOLTS BOARD EXP. SOLAR / CHARGER GROUND BR GRN WT YE BLU RED BR GRN WT YE BLU RED + ID RESET ALARM 30

ADDITIONAL FEATURES ACCESSORY FEATURES ON CONTROL BOARD ACCESSORY FEATURES ON CONTROL BOARD A Open Input (& common) (3-Button Control Station, 4 terminals Open command - opens a closed gate. Hard open (maintained switch overrides external safeties and resets alarm condition) total) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate (within line-of-sight). B Close Input (& common) Close command - closes an open gate. (3-Button Control Station, 4 terminals Hard close (maintained switch overrides external safeties and resets alarm condition within line-of-sight) total) C Stop Input (& common) Stop command - stops a moving gate. (3-Button Control Station, 4 terminals Hard stop (maintained switch overrides Open and Close commands and resets alarm condition) total) If maintained, pauses Timer-to-Close at OPEN limit. Overrides Open and Close commands (within line-of-sight). D Fire Dept Open Input Acts as hard open. (2 terminals) Maintained input overrides (ignores) external safeties (photoelectric sensor and edge), pauses Timer-to-Close momentary input logic as single button control and safeties remain active, re-enables Timer-to-Close. E Exit Loop Input Open command - opens a closed gate. (2 terminals) Soft open (maintained switch does not override external safeties and does not reset alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. F Shadow Loop Input Loop detector connection when loop is positioned under gate. (2 terminals) - Holds open gate at open limit - Disregarded at CLOSE limit and during gate motion - Pauses Timer-to-Close at OPEN limit G CLOSE EYES/Interrupt Loop Input CLOSE EYES/Interrupt Loop detector connection when loop is along the side of the gate. (2 terminals) - Holds open gate at open limit - Stops and reverses a closing gate to open limit - Pauses Timer-to-Close at OPEN limit Close Direction Photoelectric Sensors, IR, or Infra-red detector wired to CLOSE EYES Input, disregarded during gate opening. Pulsed Photoelectric Sensors = monitored device putting out a pulse train when unblocked. Photoelectric Sensors, IR, Infra-red detector, contact opens fully with obstruction. H Close Edge Close Direction Edge Sensor to Close Safety Input, disregarded during gate opening (2 terminals) I Open Eyes/Edge Open Direction Photoelectric Sensors, IR, Infra-red detector wired or Edge Sensor to Close Entrapments Input, (2 terminals) disregarded during gate closing, Pulsed Photoelectric Sensors = monitored device putting out a pulse train when unblocked. Photoelectric Sensors, IR, Infra-red detector, edge sensor = normally open contact, contact reverses for 2 seconds with obstruction. J Comm Link Commercial Link (two wires) - connects two operators together (primary-secondary wired connection) (2 terminals) K Lock Outputs: Maglock Relay contact output, Normally - closed (N.C.) output for maglocks (2 terminals, N.C. and COM) Relay activates prior to motor activation and during motor run. Relay is off when motor is off. L Solenoid Lock & Common Normally - open (N.O.) output for solenoid locks (2 terminals, N.O. and COM) Relay activates prior to motor activation and during motor run. Relay is off when motor is off. M Accessory Power Out 24 Vdc voltage out to power accessories, will turn off when gate is not in motion to save battery power Switched, (2 terminals) Always on if Expansion Board is connected. N Accessory Power Out 24 Vdc voltage out to power accessories, always ON Un-switched, (2 terminals) 31

ADDITIONAL FEATURES EXPANSION BOARD OVERVIEW EXPANSION BOARD OVERVIEW To AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to the AUX relay contact terminal blocks. QUICK CLOSE Switch OFF: No change to the gate's normal operation. ON: When CLOSE EYES/Interrupt loop is deactivated it causes an opening or a stopped gate to close (ignores the Timer-to-Close). AC FAIL OPEN/BATT Switch OPEN: Loss of AC power will cause gate to immediately OPEN and remain OPEN until AC power is restored (enabling the Timer-to-Close). BATT: With loss of AC power, gate will remain in present position and operator is powered from batteries. LOW BATT/EXIT LOOP FAIL • When AC power is OFF and battery voltage is low the gate will latch at a limit until AC power is restored or batteries voltage increases. Switch • Option select switch set to OPEN forces gate to latch at the OPEN limit if it is at the OPEN limit or on next open command until AC power is restored or battery voltage increases. • Option select switch set to CLOSE forces gate to latch at CLOSE limit if at CLOSE limit or on next CLOSE command until AC power restored or battery voltage increases. • Constant pressure on a hard command input overrides to open or close the gate. • Low battery detect point = 22 V • When set to OPEN, if the EXIT plug-in loop detector detects a fault, then the gate will open and remain open until fault is cleared. When set to CLOSE, then plug-in EXIT loop detector faults are ignored (EXIT loop is faulted and inoperative). ANTI-TAIL OPEN/CLOSE OFF: When CLOSE EYES/Interrupt loop is activated it causes a closing gate to stop and reverse. SELECTION switch ON: When CLOSE EYES/Interrupt loop is activated it causes a closing gate to pause. Once the vehicle is clear the gate will continue to close. AUX RELAY switches Set the AUX RELAY switches as needed to obtain the desired function: AUX RELAY SWITCH AUX RELAY 1 AUX RELAY 2 SETTING SETTINGS 1 2 3 Off (no feature OFF OFF OFF Relay always off. Use this Aux Relay setting to conserve Relay always off. Use this Aux Relay setting to conserve battery power. selected) battery power. Open Limit OFF OFF ON Energizes at open limit. Use with SAMS (Sequenced Access Management Energizes when at open limit. Use with SAMS (Sequenced Access Switch System, jointly with barrier gate) Management System, jointly with barrier gate) Close Limit OFF ON OFF Energizes when not at close limit. Connect “Gate Close/Secure” indicator Energizes when not at close limit. Connect “Gate Not Closed/Secure” Switch (e.g. light). indicator (e.g. light). Gate Motion OFF ON ON Energizes when motor is on (gate in motion). Connect “Gate In Motion” Energizes when motor is on (gate in motion). Connect “Gate In Motion” indicator (e.g. warning light or sounder). indicator (e.g. warning light or sounder). Pre-Motion ON OFF OFF Energizes 3 seconds before gate motion and remains energized during gate Not used. Delay motion. Connect “Gate In Motion” indicator (e.g. warning light or sounder). Power ON ON OFF Energizes when AC power or solar power is present. There is approximately Energizes when on battery power. There is approximately a 10-12 a 10-12 second delay before relay cutoff, after AC shutdown. second delay before relay cutoff, after AC shutdown. Tamper ON OFF ON Energizes if gate is manually tampered with by being pushed off of close Energizes if gate is manually tampered with by being pushed off of close limit. Connect alert (e.g. light or sounder). limit. Connect alert (e.g. light or sounder). Cycle Quantity ON ON ON The OPEN, CLOSE, and STOP LEDs will blink out the cycle count Not used. Feedback* See below. CYCLE COUNT * First, note the current Aux Relay switch positions. To determine the actual cycles that the gate operator has run (in thousands), set all three Aux Relay switches to Single the ON setting for Aux Relay 1. The Expansion Board’s Button SBC OPEN, CLOSE, and STOP LEDs will blink out the cycle Control count, with OPEN LED blinking 1000’s, CLOSE LED blink Com D Station Open 10,000’s, STOP LED blinking 100,000’s, and Close A 3-Button simultaneously all three LED’s blink 1,000,000’s (e.g. Stop B Control Open blinks 3 times, Close blinks 6 times, and Stop Com C Station blinks once. Cycle count is 163,000.). Cycle count displayed is between 1,000 and 9,999,000 cycles. After servicing, set Aux Relay switches back to their Shadow Loop AUX Relay 1 N.O. AUX Relay 2 N.O. AUX Relay 2 N.C. AUX Relay 1 N.C. Interrupt Loop Exit Loop appropriate positions. Cycle count cannot be reset or F E H Com I Com changed. If under 1,000 cycles the Open, Close, and Stop LEDs will turn on for 10 seconds, then turn off. G 32

ADDITIONAL FEATURES ACCESSORY FEATURES ON EXPANSION BOARD ACCESSORY FEATURES ON EXPANSION BOARD A Open Input (& common) (3-Button Control Station, Open command - opens a closed gate. Soft close (maintained switch does not override external safeties and does not reset alarm condition) 4 terminals total) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. B Close Input (& common) Close command - closes an open gate. (3-Button Control Station, Soft close (maintained switch does not override external safeties and does not reset alarm condition) 4 terminals total) C Stop Input (& common) Stop command - stops a moving gate. (3-PB station, 4 terminals total) Hard stop (maintained switch overrides Open and Close commands and resets alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Overrides an Open or Close command. D Single Button Control, SBC Gate command sequence - Open, Stop, Close, Stop, ... (2 terminals) Soft open (maintained switch does not override external safeties and does not reset alarm condition) E Exit Loop Input Loop wire connection for plug-in loop detector when loop is inside secured area near gate. (2 terminals) Open command - opens a closed gate. Soft open (maintained switch does not override external safeties and does not reset alarm condition) If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. F Shadow Loop Input Loop wire connection for plug-in loop detector when loop is along side gate. (2 terminals) - Holds open gate at open - Disregarded at Close limit and during gate motion - Pauses Timer-to-Close at Open Limit G Interrupt Loop Input Loop wire connection for plug-in loop detector when loop is positioned under gate. (2 terminals) - Holds open gate at open - Stops and reverses a closing gate - Pauses Timer-to-Close at Open Limit H AUX Relay #1 Normally - open and normally - closed relay contacts to control external devices, Function of relay contact activation determined by AUX Relay #1 option switch settings. (For connection of Class 2, low voltage (<32 V), DC or AC, max 5 Amps, power sources only) I AUX Relay #2 Normally-open and normally-closed relay contacts to control external devices, Function of relay contact activation determined by AUX Relay #2 option switch settings. (For connection of Class 2, low voltage (<32 V), DC or AC, max 5 Amps, power sources only) AUX RELAY WIRING EXAMPLE SAMS WIRING WITH RELAYS NOT ENERGIZED Main Board SET OPEN SET CLO E XM T R N W RK Exit Input Barrier Arm Operator FF ON E A E Class 2 Power Source S CO D ) IM T 0 E UP MOVE C G TE 2 5 6 (32 V max, 5 A max) TATUS N UT P WER A T CH RG NG T MER GA E M Auxiliary Command + — NO N.C. COM J 5 Aux Relay + + CC SS RY SW A T DC P WER P WER N N.O. B ARD XP Access Device SO AR / CH RG R RO ND BR G N WT YE B U ED BR G N WT E LU ED ID R S T A A M Expansion Board Shadow Input Warning Light Dipswitch settings for AUX Relay 1: 1-OFF, 2-OFF, 3-ON AUX Relay 1 33

ADDITIONAL FEATURES GATE OPERATOR SETUP EXAMPLES GATE OPERATOR SETUP EXAMPLES The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary secondary entrapment protection systems. RESIDENTIAL SMALL: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns RESIDENTIAL LARGE: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access trumps security concerns COMMERCIAL: Business site where security (gate closed) is important INDUSTRIAL: Large business site where security is required Setting RESIDENTIAL SMALL RESIDENTIAL LARGE COMMERCIAL INDUSTRIAL Quick Close switch setting Normally set to OFF. Normal gate Normally set to OFF. Normal gate Normally set to OFF. Normal gate Set to ON, so that gate closes close (timer or control). close (timer or control). close (timer or control). immediately after vehicle passes interrupt loop. AC Fail Open switch setting Normally set to BATT. Run on Normally set to BATT. For local Normally set to BATT. Run on Normally set to BATT. Run on battery if AC power fails. jurisdiction requirement, set to battery if AC power fails. battery if AC power fails. OPEN so that gate immediately opens upon AC power fail. Low Battery switch setting Normally set to OPEN. If powered Normally set to OPEN. If powered Normally set to CLOSE. If powered Normally set to CLOSE. If powered from battery and battery is low, from battery and battery is low, from battery and battery is low, from battery and battery is low, gate stays open. gate stays open. gate stays close. gate stays close. Anti-Tail switch setting Normally set to OFF. Interrupt loop Normally set to OFF. Interrupt loop Set to ON. In attempt to prevent Set to ON. In attempt to prevent reverses a closing gate. reverses a closing gate. vehicle tail-gating, interrupt loop vehicle tail-gating, interrupt loop pauses a closing gate. pauses a closing gate. Bipart Delay switch setting For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for gate that delays upon opening gate that delays upon opening gate that delays upon opening gate that delays upon opening Aux Relay Out – Open Typically not required. Use with SAMS (Sequence Access 1) Use with SAMS (Sequence Access 1) Use with SAMS (Sequence Access Limit Switch Management System) Management System) Management System) 2) Connect “Gate Open” indicator 2) Connect “Gate Open” indicator (e.g. light) (e.g. light) Aux Relay Out – Close Typically not required. Typically not required. Connect “Gate Close/Secure” Connect “Gate Close/Secure” Limit Switch indicator (e.g. light) indicator (e.g. light) Aux Relay Out – Gate Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Motion visual alert system) visual alert system) visual alert system) visual alert system) Aux Relay Out – Pre- Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Motion Delay visual alert system) visual alert system) visual alert system) visual alert system) Aux Relay Out – Power Attach visual alert to know when Attach visual alert to know when Attach visual alert to know when Attach visual alert to know when system is charging batteries (i.e. system is charging batteries (i.e. system is charging batteries (i.e. system is charging batteries (i.e. not running on batteries) not running on batteries) not running on batteries) not running on batteries) Aux Relay Out – Tamper Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or visual alert system) to indicate if visual alert system) to indicate if visual alert system) to indicate if visual alert system) to indicate if gate is manually tampered with by gate is manually tampered with by gate is manually tampered with by gate is manually tampered with by being pushed off of close limit being pushed off of close limit being pushed off of close limit being pushed off of close limit Cycle Quantity Feedback Use during servicing only to Use during servicing only to Use during servicing only to Use during servicing only to determine operator cycles determine operator cycles determine operator cycles determine operator cycles Fire Dept Open input Typically not required. Connect emergency access system Typically not required. Typically not required. (Knox box switch, SOS system, etc.) 34

ADDITIONAL FEATURES LIMIT SETUP WITH A REMOTE CONTROL LIMIT SETUP WITH A REMOTE CONTROL To set the limits using a remote control, first you will need a 3-button remote control that has been programmed for OPEN, CLOSE, and STOP. Refer to the Programming section. INITIAL LIMITS AND FORCE ADJUSTMENT For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the ET OP N SET C OSE R E W R O F O MT 10 “ RE limits and force. TU DE T MO E 1 B G TE SET OPEN SET CLOSE 2 5 6 E I F 0 M D N UT OW R M R AT LOW A NO T TA US CO ES A T CH R I G TE M V NG CC P R OV H C O E Y S N ER Ensure the gate is closed. F 1 5 Press the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting 15 CC S ORY W BA T P WER OWER mode. N XP OL R / HA GER BR G N WT E B U ED R G N WT YE B U R D 2 Press and hold the OPEN or CLOSE button on the remote control until the gate reaches the desired open position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control. 3-Button Remote Control programmed for OPEN, CLOSE, and STOP 3 Once the gate is in the desired open position, press and release the STOP button on the remote control. 4 Press limit. and release the OPEN button on the remote control again to set the open 5 Press and hold the CLOSE or OPEN button on the remote control until the gate reaches the desired close position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control. 6 Once the gate is in the desired close position, press and release the STOP button on the remote control. 7 limit. Press and release the CLOSE button on the remote control again to set the close 8 Cycle the gate open and close. This automatically sets the force. When limits are set properly the operator will automatically exit limit setting mode. ADJUST THE LIMITS If the limits have already been set the operator will exit the limit setting mode after resetting each limit. Set the Close Limit Only Set the Open Limit Only 1 Press the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode. 1 Press the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode. 2 desired close position. The gate can be jogged back and forth using the OPEN Press and hold the CLOSE button on the remote control until the gate reaches the 2 Press and hold the OPEN button on the remote control until the gate reaches the desired open position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control. and CLOSE buttons on the remote control. 3 Once the gate is in the desired close position, press and release the STOP button on the remote control. 3 Once the gate is in the desired open position, press and release the STOP button on the remote control. Press and release the CLOSE button on the remote control again to set the close 4 limit. 4 Press limit. and release the OPEN button on the remote control again to set the open When the close limit is set properly the operator will automatically exit limit setting When the open limit is set properly the operator will automatically exit limit setting mode. 35 mode.

TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS The control board is equipped with many LEDs that have a variety of functions. The control board LEDs indicate the status of the operator, assist with programming, and diagnose potential problems with the operator. LIMIT SETUP LEDS GREEN XMITTER LED DIAGNOSTIC CODES LEDS SET OPEN SET CLOSE XMITTER OPEN NETWORK OFF ON SBC STATUS LEDS PRESS & RELEASE INPUT LEDS CLOSE TO BEGIN (SECONDS) LIMIT 10 “FIRE SETUP DEPT.” MOVE 1 OPEN GATE 2 5 60 STOP EXIT OFF 180 MIN MAX INPUT POWER TIMER BATT LOW DIAGNOSTIC STATUS: CODES BATT CHARGING GATE MOVING ACC PWR OVLD SHADOW CLOSE EYES/ - INTERRUPT + - + J5 N.C. N.O. COM J15 LOCK + - - + SW. - ACCESSORY BATT DC POWER POWER - + ON + CLASS 2 SUPPLY 24 VOLTS BOARD EXP. SOLAR / CHARGER GROUND BR GRN WT YE BLU RED BR GRN WT YE BLU RED + - ID RESET ALARM LIMIT SETUP LEDS GREEN XMITTER LED SET OPEN SET CLOSE OPERATOR MODE EXPLANATION XMITTER LED EXPLANATION LED LED OFF No remote control activity, normal operation. BLINKING BLINKING NORMAL MODE Limits are not set. ON Programming mode active. OFF OFF NORMAL MODE Limits are set. FAST Recognized remote control signal. BLINKING BLINKING LIMIT SETTING MODE Limits are not set. FASTER Unrecognized remote control signal. BLINKING ON LIMIT SETTING MODE Open limit is not set. FASTEST Remote controls are being erased. ON BLINKING LIMIT SETTING MODE Close limit is not set. ON ON LIMIT SETTING MODE Limits are set. 36

TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS DIAGNOSTIC CODES LEDS YELLOW DIAGNOSTIC LED RED DIAGNOSTIC LED # BLINKS MEANING CORRECTION # BLINKS MEANING CORRECTION 1 BLINK Low Power Mode (not an error) 2 BLINKS Current Sense Motor control circuit fault, replace 2 BLINKS ID resistor failure Check ID resistor wiring, clear limit control board settings and reset limits 3 BLINKS FET Failure Motor control circuit fault, replace 3 BLINKS Exceeded Maximum Check gate travel, if necessary adjust control board Run Timer force setting 4 BLINKS RAM Failure Memory failure, replace control board 5 BLINKS RPM (obstruction) Check for obstruction, if necessary 5 BLINKS Flash Memory Memory failure, replace control board adjust force setting Failure 6 BLINKS Current (obstruction) Check for obstruction, if necessary 6 BLINKS EEPROM Failure Memory failure, replace control board adjust force setting 7 BLINKS Watchdog Failure Controller failure, replace control 7 BLINKS Position failure Check gate travel, clear limit settings board and reset limits 8 BLINKS Brownout Check power harness or line voltage 12 BLINKS Loop Error One of the loops is in error. Refer to the 9 BLINKS Fail Control Board failure loop detector to determine the error. 10-14 BLINKS Software Failure Cycle power to the control board. If continues replace control board. STATUS LEDS INPUT LEDS INPUT POWER OFF OFF state OPEN INPUT OFF Input inactive ON AC charger or Solar power available ON Input active BATT OFF Not charging BLINK Input active on other operator CHARGING ON Trickle charge CLOSE INPUT OFF Input inactive FAST BLINK High current charge ON Input active FASTER BLINK Over voltage error BLINK Input active on other operator TIMER OFF The timer is disabled STOP INPUT OFF Input inactive ON The timer is enabled ON Input active MEDIUM BLINK The timer is running BLINK Input active on other operator FAST BLINK The timer is paused FIRE DEPT OFF Input inactive FASTER BLINK The timer is cancelled INPUT ON Input active GATE MOVING OFF The gate is stopped BLINK Input active on other operator ON The gate is opening or closing SBC INPUT OFF Input inactive FASTEST BLINK The operator is in E2 ON Input active BATT LOW OFF No battery error BLINK Input active on other operator ON Battery low error OPEN SAFETY OFF Input inactive SLOW BLINK Battery dead error INPUT ON Input active MEDIUM BLINK Battery over current error BLINK Input active on other operator FAST BLINK Battery over voltage error CLOSE SAFETY OFF Input inactive FASTER BLINK Extreme temperature error INPUT ON Input active FASTEST BLINK Battery disconnected error BLINK Input active on other operator ACC PWR OVLD OFF OFF state ON Accessory overload protector opened 37

TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Operator does not a) No power to control board a) Check AC and battery power run and diagnostic b) Open fuse b) Check fuses LED not on. c) If on battery power only, low or dead batteries c) Charge batteries by AC or solar power or replace batteries d) Defective control board d) Replace defective control board Control board a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue powers up, but b) Reset button is stuck b) Check Reset button motor does not run. c) Stop button active c) Check Stop button is not “stuck on” d) If on battery power only, low or dead batteries d) Charges batteries by AC or solar power or replace batteries e) Open or Close input active e) Check all Open and Close inputs for a “stuck on” input f) Entrapment Protection Device active f) Check all Entrapment Protection Device inputs for a “stuck on” sensor g) Vehicle loop detector or probe active g) Check all vehicle detector inputs for a “stuck on” detector h) Defective control board h) Replace defective control board Relay clicks with a) Arm jammed or not connected a) Disengage the arm and ensure arm moves freely command, but motor b) Defective motor or motor wires b) Inspect motor wires for open wire, shorted wires, damage, etc. Else, replace arm. does not turn on. c) Defective control board c) Replace defective control board. Arm moves, but a) Arm does not extend or retract enough during a) Disengage the arm and ensure arm moves freely cannot set correct travel b) Examine the hinge point where the arm mounts to the gate post. Make sure that the arm limits. b) Arm is interfering with mounting bracket housing does not hit or interfere with the gate post or mounting bracket. Correct as c) Gate is too difficult to move necessary. c) Disconnect arm from gate and move gate manually. Gate must move easily and freely through its entire range, limit-to-limit. Repair gate as needed. Gate does not fully a) Arm does not extend or retract enough during a) Disengage the arm and ensure arm moves freely open or fully close travel b) Examine the hinge point where the arm mounts to the gate post. Make sure that the arm when setting limits. b) Arm is interfering with mounting bracket housing does not hit or interfere with the gate post or mounting bracket. Correct as c) Gate is too difficult to move necessary. c) Remove arm from gate and move gate manually. Gate must move easily and freely through its entire range, limit-to-limit. Repair gate as needed. Operator does not a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue respond to a wired b) Check Open and Close command input LEDs b) Check all Open and Close inputs for a “stuck on” input control/command c) Stop button is active c) Check Stop button is not “stuck on” (example: Open, Close, SBC, etc.) d) Reset button is stuck d) Check Reset button e) If on battery power only, low or dead batteries e) Charges batteries by AC or solar power or replace batteries f) Entrapment Protection Device active f) Check all Entrapment Protection Device inputs for a “stuck on” sensor g) Vehicle loop detector or vehicle probe active g) Check all vehicle detector inputs for a “stuck on” detector h) Defective control board h) Replace defective control board Operator does not a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue respond to a b) Check XMITTER LED when wireless control is b) Activate wireless control and check XMITTER LED is on. Re-learn wireless control/ wireless control or active transmitter to control board. Replace wireless control as needed. transmitter c) Stop button is active c) Check Stop button is not “stuck on” d) Reset button is stuck d) Check Reset button e) Poor radio reception e) Check if similar wired control operates correctly. Check if wireless controls works properly f) Defective control board when within a few feet of operator. Check operator’s antenna and antenna wire. Check other wireless controls or devices. f) Replace defective control board 38

TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Gate stops during a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue travel and reverses b) Inherent force obstruction detection b) Check for obstruction in gate’s path or travel. Remove arm from gate and move gate immediately. c) External Entrapment Protection Device manually. Gate must move easily and freely through its entire range, limit-to-limit. activation Remove obstruction or repair gate as needed. d) Control (Open, Close) becoming active c) Check all Entrapment Protection Device inputs for an active sensor e) Vehicle loop detector active d) Check all Open and Close inputs for an active input f) Low battery voltage e) Check all vehicle detector inputs for an active detector f) Battery voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries Gate opens, but will a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue not close. b) Open control active b) Check all Open inputs for an active input c) Close Entrapment Protection Device active c) Check all Entrapment Protection Device inputs for an active sensor d) Vehicle loop detector active d) Check all vehicle detector inputs for an active detector e) Loss of AC power with AC FAIL set to OPEN e) Check AC power and AC Fail option setting f) Low battery with LOW BATT set to OPEN f) Battery voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or g) Fire Dept input active replace batteries g) Check Fire Dept input Gate closes, but will a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue not open. b) Open Entrapment Protection Device active b) Check all Entrapment Protection Device inputs for an active sensor c) Vehicle loop detector active c) Check all vehicle detector inputs for an active detector d) Low battery with LOW BATT switch set to close d) Battery voltage must be 22.0 Vdc or higher e) Low battery with LOW BATT option set to e) Check if AC power is available. If no AC power, then running on batteries and battery CLOSE voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries Gate does not close a) Timer-to-Close not set a) Check Timer-to-Close (TTC) setting from Timer-to-Close. b) Open control active b) Check all Open inputs for an active input c) Close Entrapment Protection Device active c) Check all Entrapment Protection Device inputs for an active sensor d) Vehicle loop detector active d) Check all vehicle detector inputs for an active detector e) Loss of AC power with AC FAIL set to OPEN e) Check AC power and AC Fail option setting f) Low battery with LOW BATT option set to OPEN f) Check if AC power is available. If no AC power, then running on batteries and battery g) Fire Dept input active voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries. g) Check Fire Dept input Vehicle Exit loop a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue activation does not b) Exit vehicle detector setup incorrectly b) Review Exit loop detector settings. Adjust settings as needed. cause gate to open. c) Defective Exit loop detector or loop wire c) Check Exit loop wire. Replace defective Exit loop detector. d) Low battery with LOW BATT option set to d) Check if AC power is available. If no AC power, then running on batteries and battery CLOSE voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries. Vehicle Interrupt a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue loop does not cause b) Vehicle detector setup incorrectly b) Review Interrupt loop detector settings. Adjust settings as needed gate to stop and c) Defective vehicle loop detector or loop wire c) Check Interrupt loop wire. Replace defective Interrupt loop detector reverse. Vehicle Shadow loop a) Check DIAGNOSTIC LEDs a) Use Diagnostic code to identify issue does not keep gate b) Vehicle detector setup incorrectly b) Review Shadow loop detector settings. Adjust settings as needed at open limit. c) Defective vehicle loop detector or loop wire c) Check Shadow loop wire. Replace defective Shadow loop detector 39

TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Obstruction in gates a) Force setting too high a) Adjust force setting. Retest that obstruction in gate’s path causes gate to stop and reverse path does not cause direction. gate to stop and reverse Photoelectric sensor a) Incorrect photoelectric sensor wiring a) Check photoelectric sensor wiring. Retest that obstructing photoelectric sensor causes does not stop or b) Defective photoelectric sensor moving gate to stop, and may reverse direction. reverse gate. b) Replace defective photoelectric sensor. Retest that obstructing photoelectric sensor causes moving gate to stop, and may reverse direction. Edge Sensor does a) Incorrect edge sensor wiring a) Check edge sensor wiring. Retest that activating edge sensor causes moving gate to stop not stop or reverse b) Defective edge sensor and reverse direction. gate. b) Replace defective edge sensor. Retest that activating edge sensor causes moving gate to stop and reverse direction. Alarm sounds for 5 a) Double entrapment occurred a) Check for cause of entrapment (obstruction) detection and correct. Press the reset button minutes or alarm to shut off alarm and reset the operator. sounds with a command. Alarm beeps three a) Low battery a) Check if AC power is available. If no AC power, then running on batteries and battery times with a voltage must be 22.0 Vdc or higher. Charge batteries by AC or solar power or replace command. batteries On dual-gate a) Defective or incorrect Operator-to-Operator a) Check operator-to-operator wiring. system, one gate is wiring b) Relearn the wireless network of one operator to the other operator. not commanding the b) Incorrect Operator-to-Operator wireless other. learning On dual-gate a) Incorrect Bipart switch setting a) Change setting of both operator’s Bipart switch settings. One operator should have Bipart system, incorrect switch ON (operator that opens first) and the other operator should have Bipart switch gate opens first or OFF (operator that opens second) closes first. Alarm beeps when running. Expansion board a) Defective main board to expansion board a) Check main board to expansion board wiring. If required, replace wire cable. function not wiring b) Check wiring to all inputs on expansion board. controlling gate. b) Incorrect input wiring to expansion board c) Replace defective expansion board or defective main board c) Defective expansion board or defective main board Maglock not a) Maglock wired incorrectly a) Check that Maglock is wired to N.O. and COM terminals. Check that Maglock has power working correctly. (do not power maglock from control board accessory power terminals). If shorting lock’s NO and COM wires does not activate Maglock, then replace Maglock or Maglock wiring Solenoid lock not a) Solenoid wired incorrectly a) Check that Solenoid is wired to N.C. and COM terminals. Check that Solenoid has power working correctly. (do not power solenoid from control board accessory power terminals). If shorting lock’s NC and COM wires does not activate Solenoid, then replace Solenoid lock or Solenoid wiring Switched (SW) a) Main control board is not going to low power a) Photoelectric sensor inputs may be active. Accessory power mode. remaining on. Accessories a) Main control board is going to low power a) With expansion board disconnected and running on batteries (no AC power or solar connected to Switch mode. power available), main board will go into low power mode. Move accessory power to (SW) Accessory Accy Power ON terminals (+, -). Connect expansion board to prevent low power mode. power not working correctly, turning off, or resetting. 40

TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Accessories a) Accessory power protector active a) Disconnect all accessory powered devices and measure accessory power voltage (should connected to b) Defective control board be 23 – 30 Vdc). If voltage is correct, connect accessories one at a time, measuring Accessory power accessory voltage after every new connection. not working b) Replace defective control board correctly, turning off, or resetting. Quick Close not a) Quick Close setting incorrect a) Check that Quick Close setting is ON working correctly. b) Interrupt loop detector or loop wire defective b) Check operation of Interrupt Loop detector c) Defective Expansion board c) Replace defective Expansion board Anti-Tailgating not a) Anti-Tail setting incorrect a) Check that Anti-Tail setting is ON working correctly. b) Interrupt loop detector or loop wire defective b) Check operation of Interrupt Loop detector c) Defective Expansion board c) Replace defective Expansion board AUX Relay not a) AUX Relay setting incorrect a) Check AUX Relay switches settings working correctly. b) AUX Relay wiring incorrect b) Check that wiring is connected to either N.O. and COM or to N.C. and COM. c) Defective Expansion board c) Set AUX Relay to another setting and test. Replace defective expansion board. 41

rating. installing or servicing operator. NC NC For continued protection against fire: COM COM LOCK LOCK To protect against fire and electrocution: NO NO • DISCONNECT power and battery BEFORE • Replace ONLY with fuse of same type and Solenoid Lock (Optional) Maglock Antenna (Optional) SET OPEN SET CLOSE (not provided) (not provided) XM TTER NETWORK OFF ON SBC OPEN PRESS & RELEASE TO BEG N (SECONDS Red WIRING DIAGRAMS LMT 10 “F RE SETUP DEPT” CLOSE MOVE 1 OPEN 12V 7AH Battery GATE 2 5 60 STOP EX T Attach to Metal Chassis OFF 180 MIN MAX Photoelectric Sensors NPUT POWER T MER BATT LOW D AGNOST C STATUS: CODES 12V 7AH Battery BATT CHARG NG GATE MOV NG ACC PWR OVLD SHADOW CLOSE Black EYES/ White + NTERRUPT White/Black Edge Photoelectric Sensors Transformer + Field Wiring White/Black 42 White Edge Accessory Power J5 Outlets NC COM To J15 J15 LOCK NO + - - + BATT DC SW POWER + POWER ACCESSORY ON + CLA S 2 SU PLY 24 VO TS Yellow EXP Blue BOARD L Black GND Red SOLAR / CHARGER GROUND BR GRN WT YE BLU RED BR GRN WT YE BLU RED + - N Connect Outlets D RESET ALARM Attach to Outlet Metal Chassis Input Power Connection to Transformer With a Single Screw Kit (If Used) EXPANSION BOARD Red Loop Detector Tranformer Run Kit (Optional) Black Purple Switch/5A Breaker Ground Black Red Wire Nut Red Primary Operator Black + Red Black Bridge Rectifier L - - Piezo Alarm Wh te White Black Red Field Wiring Black N.C. White GROUND Secondary Operator Gray Yellow Blue White Reset Switch N Two 12V Solar Panels Brown Wire Loop Wire Loop Input Power Connection in Series + + GND Red - - Wire Loop Attach to Outlet Purple EMI FILTER/SURGE PROTECTION BOARD Orange Field Wiring Metal Chassis With a Single Screw Transformer 200 VA STANDARD CONTROL BOX

rating. installing or servicing operator. For continued protection against fire: NC NC To protect against fire and electrocution: Antenna COM COM LOCK LOCK • DISCONNECT power and battery BEFORE NO NO • Replace ONLY with fuse of same type and Solenoid Lock (Optional) Maglock Coaxial Antenna Cable (Optional) SET OPEN SET CLOSE (not provided) (not provided) XM TTER NETWORK OFF ON SBC OPEN WIRING DIAGRAMS PRESS & RELEASE O BEG N (SECONDS Red LMT 10 “F RE SETUP DEPT” CLOSE MOVE 1 OPEN 12V 7AH Battery GATE 2 5 60 STOP EX T Attach to Metal Chassis OFF 180 MIN MAX Photoelectric Sensors NPUT POWER T MER BATT LOW D AGNOST C STATUS: CODES 12V 7AH Battery BATT CHARG NG GATE MOV NG ACC PWR OVLD SHADOW CLOSE Black EYES/ White + NTERRUPT White/Black Edge Photoelectric Sensors + Transformer Field Wiring 43 White/Black White Edge Accessory Power J5 Outlets NC COM To J15 J15 LOCK NO + - - + BATT DC SW POWER + POWER ACCESSORY ON + CLA S 2 SU PLY 24 VO TS Yellow EXP Blue BOARD L Black GND Red SOLAR / CHARGER GROUND BR GRN WT YE BLU RED BR GRN WT YE BLU RED + - N Connect Outlets D RESET ALARM EXPANSION BOARD Input Power Connection to Transformer Kit (If Used) Loop Detector Red Tranformer Run Kit (Optional) Black Purple Switch/5A Breaker Ground Black Red Wire Nut Red Primary Operator Black + Red Field Wiring Black Bridge Rectifier L - - Piezo Alarm N.C. White White Black Red Black White Secondary Operator Gray Yellow Blue White Reset Switch Wire Loop Wire Loop N Two 12V Solar Panels Wire Loop Brown Input Power Connection in Series + + GND Red - - Field Wiring Purple EMI FILTER/SURGE PROTECTION BOARD Orange Transformer 200 VA LARGE METAL CONTROL BOX (XLM)

ACCESSORIES ENTRAPMENT PROTECTION DEVICES MISCELLANEOUS PHOTOELECTRIC SENSORS (NON-CONTACT) PLUG-IN LOOP DETECTOR The photoelectric sensors are designed to detect an obstacle in the Low power. Conveniently plugs into existing control board. path of the electronic beam and stop the operator. Includes Model LOOPDETLM mounting brackets. Models AOMRON E3K-R10K4-NR (retro-reflective), RETROAB 60-2728 (retro-reflective), CPS-UN4 (through beam) LOOP DETECTOR Low power loop detectors mounted and wired separately inside SENSING EDGE (2-WIRE, NON-MONITORED, control box. CONTACT) Model LD7LP Sensing edges can detect an obstacle upon contact and stop the operator. VEHICLE SENSING PROBE Models G65MG0204, G65MG0205, G65MGR205, and The vehicle sensing probe is buried in the ground and can detect a G65MGS205 car as it approaches and will then open the gate. SENSING EDGE CHANNEL Model CP3 Mounting channel for all MG020 type edges. Model G65ME120C5 SOLAR PANEL KIT - 10 WATT REMOTE CONTROLS This kit is to replace or add a solar panel to the operator application. Up to four solar panels can be connected to the Chamberlain offers a variety of LiftMaster remote controls to satisfy your application needs. operator. Single-button to 4-button, visor or key chain. The following remote controls are compatible with operators manufactured by Chamberlain after 1993. Contact your authorized LiftMaster Model SOLPNL10W12V (requires 2 minimum) dealer for additional details and options. BATTERY FOR GATE ACCESS SYSTEMS 3-BUTTON REMOTE CONTROL Gate access system batteries replace or upgrade the gate operator The 3-button remote control can be programmed to control the batteries. operator. Includes visor clip. Model 29-NP712 (standard 7 AMP-Hour Battery, 12 Vdc, to Model 893MAX replace original batteries provided with operator, reuse existing harnesses) 3-BUTTON MINI-REMOTE CONTROL Model A12330SGLPK (upgrade 33 AMP-Hour Battery, 12 Vdc, includes 33AH harness. Ideal for solar applications and extended The 3-button remote control can be programmed to control the battery backup). For use with Large Metal Control Box ONLY. operator. Includes key ring and fastening strip. Two identical 12 Vdc batteries are required for each gate Model 890MAX operator. Do not mix 7AH and 33AH batteries within a gate operator. KEYLESS ENTRY Enables homeowner to operate gate operator from outside by SOLENOID GATE LOCK entering a 4-digit code on a specially designed keypad. The automatic gate lock is a solenoid-driven lock that Model 877MAX automatically unlocks when the gate is open and locks when the gate is closed. Can be mounted onto a gate or post. Can be MISCELLANEOUS released in case of emergency. REMOTE ANTENNA EXTENSION KIT Models GC824 (115 Vac) and GC824-12 (12/24 Vac/dc) The remote antenna extension kit allows the antenna to be remotely installed. MAGNETIC GATE LOCK Model 86LM Outdoor magnetic lock, transformer, junction box, mounting plate and hardware. Not for use with Solar Applications. Must be WIRELESS ACCESS CONTROL RECEIVER powered separately. Access control receiver for up to 450 remote controls. Model MG1300 Model STAR450-315 TRANSFORMER RUN KIT (OPTIONAL Model LA500HDTKITSTD (for Standard Control Box) Model LA500HDTKITXLM (for Large Metal Control Box) 44

WARRANTY LIFTMASTER 3 YEAR RESIDENTIAL / 2 YEAR COMMERCIAL LIMITED WARRANTY The Chamberlain Group, Inc. (“Seller”) warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of 3 year residential/ 2 year commercial from the date of purchase [and that the LA500™ and LA500CONT™ are free from defect in materials and/or workmanship for a period of 3 year residential/ 2 year commercial from the date of purchase]. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option. ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 3 YEAR RESIDENTIAL/ 2 YEAR COMMERCIAL LIMITED WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE LA500™ AND LA500CONT™, WHICH ARE LIMITED IN DURATION TO THE 3 YEAR RESIDENTIAL/ 2 YEAR COMMERCIAL LIMITED WARRANTY PERIOD FOR THE LA500™ AND LA500CONT™], AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE, INCLUDING BUT NOT LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 45

845 Larch Avenue Elmhurst, Illinois 60126-1196 01-36213 © 2011, The Chamberlain Group, Inc. – All Rights Reserved


Document Created: 2012-01-10 13:39:57
Document Modified: 2012-01-10 13:39:57
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC