Exhibit D Users Manual per 2 1033 b3

FCC ID: HBW7192

Users Manual

Download: PDF
FCCID_1402278

® 3-BUTTON REMOTE CONTROLS MODELS 953EV, 953EVC, 956EV AND 956EVC For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate up to three garage door openers. To prevent possible SERIOUS INJURY or Make sure the garage door opener has a working light bulb because it is a programming DEATH from a moving gate or garage door: indicator. • ALWAYS keep remote controls out of reach of children. NEVER permit children GARAGE ACCESS SYSTEM GARAGE ACCESS SYSTEM to operate or play with remote controls. REMOTE KEYCHAIN REMOTE • Activate gate or door ONLY when it can be MODELS 953EV AND 953EVC MODELS 956EV AND 956EVC seen clearly, is properly adjusted and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or LED door. LED PREPARE Locate the Learn Locate the Program button on the button on the garage remote control. door opener. 953EV & Program Button NOTE: Your garage door 953EVC opener may look different. Learn LED OR OR Learn Green LED or Learn Red/Orange LED 956EV & Yellow 956EVC Purple Program Button PROGRAM THE REMOTE CONTROL (953EV & 953EVC) 1 2 Press and 3 Press and release the remote release the control button you want to use... Learn button Check to see if the garage door opener To enter on the garage light bulb blinks. If not, wait for the programming door opener. remote control LED to light solid then mode, use the slowly press and release the remote visor clip to control button again. Repeat until the press the Program light bulb blinks. button until the LED The Learn LED will light. DO NOT press the button after the on the front of the light bulb blinks. remote control turns on. Within 30 seconds... 4 To exit programming mode, press 5 To test, press the programmed button on 6 Install the visor clip. any remote control button except the remote control... the button that was just programmed. The garage door opener will activate.

PROGRAM THE REMOTE CONTROL (956EV & 956EVC) 1 Using a safety pin or paper 2 Press and 3 Press and release the remote clip, press the Program button release the control button you want to use... until the LED on the front of Learn button Check to see if the garage door opener the remote control turns on. on the garage light bulb blinks. If not, wait for the door opener. remote control LED to light solid then slowly press and release the remote control button again. Repeat until the light bulb blinks. The Learn LED will light. DO NOT press the button after the light bulb blinks. Within 30 seconds... 4 To exit programming mode, press 5 To test, press the programmed button on the remote control... any remote control button except the button that was just programmed. The garage door opener will activate. BATTERY The LED on your remote will stop flashing when the battery is low and needs to be replaced. To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V2032 coin cell batteries. Dispose of old battery properly. To prevent possible SERIOUS INJURY or 953EV & 953EVC 956EV & 956EVC DEATH: Pry open the case first in the middle (1), then Pry open the case with a screwdriver blade. • NEVER allow small children near batteries. • If battery is swallowed, immediately notify at each side (2 and 3) with the visor clip. doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 3V2032 coin batteries. • DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate. NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. 3 Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this 1 device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2 WARRANTY REPLACEMENT PARTS ONE YEAR LIMITED WARRANTY Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20 The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from Visor Clip defect in materials and/or workmanship for a period of 1 year from the date of purchase. (Models 953EV & 953EVC ONLY) . . . . 20B137 1-800-528-9131 www.chamberlain-diy.com 114A3924 © 2011, The Chamberlain Group, Inc. All Rights Reserved


Document Created: 2010-12-20 15:09:43
Document Modified: 2010-12-20 15:09:43
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC