User Manual SL3000 English Manual for FCC 01-37920 Pt2

FCC ID: HBW6761

Users Manual

Download: PDF
FCCID_2747023

CONTROL BOARD OVERVIEW LEARN BUTTON The LEARN button is used for programming (refer to Programming). DIAGNOSTIC DISPLAY The diagnostic display will show the operator type, firmware version, and codes. The operator type will display as “SL” followed by a “30” which indicates the operator type as SL3000U. The firmware version will show after the operator type, example “1.2”. For more information about the codes refer to the Troubleshooting section. HANDING BUTTONS The handing buttons are used to determine which direction the gate will open and they are also used to set the limits OPEN LEFT OPEN RIGHT (refer to the Adjustment section). HANDING OPEN RIGHT If the operator is installed on the right side of the drive when looking out of the property, a swing gate will swing to the right (turn counter clockwise) when opening and a slide gate will slide to the right when opening. OPEN LEFT If the operator is mounted on the left side of the drive when looking out of the property, a swing gate will swing to the left (turn clockwise) when opening and a slide gate will slide to the left when opening. NOTE: For gates installed on the outside of the property, the setting will be opposite. Determine the direction by looking towards the property from the outside. BIPART DELAY Used in dual gate applications where a maglock, solenoid lock, or decorative overlay would require one gate to close before the other. BIPART DELAY The BIPART DELAY is also used in applications where one gate travels a longer distance than the other. 4 ON The operator with the BIPART DELAY dial ON will delay from the close limit when opening and be the first to close from 2 6 the open limit. 8 OFF No affect. TIMER-TO-CLOSE (TTC) The TTC is factory set to OFF (0). Rotate the TIMER-TO-CLOSE dial to the desired setting (0 to 180 seconds). Any radio command, single button control, or CLOSE command on the control board prior to the TTC expiring will close the gate. The TTC is reset by any signals from the open controls, loops, close edges, and close photoelectric sensors. 0 seconds (OFF) The gate will remain open until the operator receives another command from a control. 1-180 seconds (ON) The gate will automatically close after the specified time period. 23

CONTROL BOARD OVERVIEW FORCE DIAL The force setting should be high enough that the gate will not reverse by itself nor cause nuisance interruptions, but low enough to prevent serious injury to a person. The force setting is the same for both the 5 6 open and close gate directions. 4 7 Settings 1-3: Fixed force settings (the force will not adjust due to gate wear or temperature changes) 3 8 Settings 4-10: Automatically increase the force due to gate wear or temperature changes ADJUST THE FORCE 2 9 1. Open and close the gate with the TEST BUTTONS, ensuring that the gate is stopping at the proper open and 1 10 close limit positions. If the gate is not stopping at the proper limits, adjust the force dial accordingly. 2. Place a solid object between the open gate and a rigid structure. Ensure that the gate, the solid object, and the rigid structure can withstand the forces generated during this obstruction test. 3. Run the gate in the close direction. The gate should stop and reverse upon contact with the solid object. If the gate does not reverse off the solid object, reduce the force setting by turning the force control slightly counter-clockwise. The gate should have enough force to reach both the open and close limits, but MUST reverse after contact with a solid object. 4. Repeat the test for the open direction. TEST BUTTONS Used to operate the gate (OPEN, STOP and CLOSE). Also used to view the code history (refer to the Troubleshooting section). STATUS LEDS LED STATE DEFINITION INPUT POWER OFF OFF state ON AC power available TIMER OFF The timer is disabled ON The timer is enabled 1 blink/second The timer is running 2 blinks/second The timer is paused 8 blinks/second The timer is cancelled GATE MOVING OFF The gate is stopped ON The gate is opening or closing 1 blink/second E1 (single entrapment) 8 blinks/second E2 (double entrapment) ACC PWR OVLD OFF OFF state ON Accessory overload protector opened 24

WIRE ACCESSORIES TO CONTROL BOARD THREE BUTTON CONTROL STATION TERMINALS FUNCTION WIRING EXAMPLE OPEN and COMM Opens a closed gate. Hard open (maintained switch overrides external safeties and resets alarm condition). If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate (within line-of-sight). + + CLOSE and COMM Closes an open gate. Hard close (maintained switch overrides external safeties and resets alarm condition within line-of-sight) + – N.C. STOP and COMM Stops a moving gate. Hard stop (maintained switch overrides Open and Close commands and resets alarm condition). If maintained, cancels Timer-to-Close at OPEN limit. Overrides Open and Close commands (within line-of-sight). FIRE DEPARTMENT TERMINALS FUNCTION WIRING EXAMPLE FIRE DEPT (-) and FIRE DEPT and OPEN terminals act as a hard open. Maintained OPEN (+) input overrides (ignores) external safeties (photoelectric sensor – and edge), pauses Timer-to-Close momentary input logic as single button control and safeties remain active, re-enables + Timer-to-Close. LOOPS The Loop terminals are used for connecting loops and various control devices such as telephone entry keypads, vehicle probes, etc. Connect the accessory to the terminals based on how the accessory should function. TERMINALS FUNCTION WIRING EXAMPLE EXIT and COM This input is a soft open command (maintained switch does not override external safeties and does not reset alarm condition). – Used for exit probe, telephone entry, external exit loop detector, + or any device that would command the gate to open. – • Opens a closing gate and holds open an open gate, if + maintained, pauses Timer-to-Close at OPEN limit. – SHADOW and COM This input is used for external shadow loop detector when loop + is positioned under the swing of the gate. • Holds open gate at open limit • Only active when the gate is at the OPEN limit, disregarded at all other times • Pauses Timer-to-Close at OPEN limit INTERRUPT and COM This input is used for photoelectric sensors and external interrupt loop detector when loop is on the outside of the gate. • Holds open gate at open limit • Stops and reverses a closing gate to open limit • Pauses Timer-to-Close at OPEN limit, activates quick close and anti-tailgate features when enabled on the expansion board 25

WIRE ACCESSORIES TO CONTROL BOARD PHOTOELECTRIC SENSORS AND EDGE SENSORS The EYES/EDGE terminals are used for connecting entrapment protection devices. At least one external monitored entrapment protection device is required prior to gate movement. Monitored entrapment protection devices should have been installed with the operator at the time of installation. Only ONE monitored device may be connected to each input. A monitored device sends a pulsed signal to the operator so the operator is aware of the device. If the operator does not receive the signal from the device indicating it is working properly, it will not run in that direction. TERMINALS FUNCTION WIRING EXAMPLE CLOSE EYES/ The CLOSE EYES/INTERRUPT input is for close INTERRUPT direction photoelectric sensors. When an obstruction is sensed during gate closing the gate will open to the full open position. This input will be disregarded – during gate opening and resets the Timer-to-Close. + – CLOSE EDGE The CLOSE EDGE input is for the close direction edge + sensors. When an obstruction is sensed during gate – closing the gate will reverse to the full open position, + disengaging the Timer-to-Close. This input will be disregarded during gate opening. OPEN EYES/ The OPEN EYES/EDGE input is for open direction A M K EDGE photoelectric sensors or edge sensors. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop. This input will be disregarded during gate closing. LOCKS MAGLOCK WIRING TERMINALS FUNCTION WIRING EXAMPLE NC and COM Normally Closed (N.C.) output for maglocks. Relay activates prior to motor activation and during CO L B motor run. Relay is off when motor is off. PLY AX - + SOLENOID LOCK WIRING NO and COM Normally Open (N.O.) output for solenoid locks. Relay activates prior to motor activation and during motor run. Relay is off when motor is off. CO L B PLY AX - + 26

EXPANSION BOARD OVERVIEW To AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to the AUX relay contact terminal blocks. PLUG-IN LOOP DETECTOR INPUTS For Plug-In Loop Detectors (Model LOOPDETLM) POWER TO MAIN BOARD MAIN CONTROL BOARD CONNECTION Connected at the factory. EYE 1 ONLY EYES/EDGE TERMINALS EYE/ 2 EDGE Page 29 3 EYE/ EDGE OPEN CLOSE COM SBC OPN CONTROL STATION TERMINALS CLS Page 29 STP COM SHADOW INTERUPT EXIT QUICK LOOP INPUTS ANTI TAIL CLOSE Page 30 SWITCH SWITCH RELAY 2 WITH CORRESPONDING SWITCHES See below. See below. Page 28 EXIT FAIL SWITCH See below. RELAY 1 WITH CORRESPONDING SWITCHES AC FAIL SWITCH Page 28 Not used. EXIT FAIL SWITCH OPEN If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, then the gate will open and remain open until fault is cleared. CLOSE If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, faults are ignored (EXIT loop is faulted and inoperative). AC FAIL SWITCH NOT USED ANTI TAIL SWITCH OFF When CLOSE EYES/Interrupt loop is activated it causes a closing gate to stop and reverse. ON When CLOSE EYES/Interrupt loop is activated it causes a closing gate to pause. Once the vehicle is clear the gate will continue to close. QUICK CLOSE SWITCH OFF No change to the gate’s normal operation. ON When CLOSE EYES/Interrupt loop is deactivated it causes an opening or a stopped gate to close (ignores the Timer-to-Close). 27

EXPANSION BOARD OVERVIEW AUXILIARY RELAY 1 AND 2 Normally Open (N.O.) and Normally Closed (N.C.) relay contacts to control external devices, for connection of Class 2, low voltage (42 Vdc [34 Vac] max 5 Amps) power sources only. Function of relay contact activation determined by switch settings. RELAY SETTING SWITCH SETTINGS AUX RELAY 1 AUX RELAY 2 1 2 3 Off (no feature OFF OFF OFF Relay always off. selected) Open Limit Switch OFF OFF ON Energizes at open limit. Use with SAMS (Sequenced Access Management System, jointly with barrier gate). Close Limit Switch OFF ON OFF Energizes when not at close limit. For an additional audible or visual display, connect an external light (low voltage). Gate Motion OFF ON ON Energizes when motor is on (gate in motion). For an additional audible or visual display, connect an external buzzer or light (low voltage). Pre-Motion Delay ON OFF OFF Energizes 3 seconds before gate motion and remains Energizes 3 seconds before gate motion and energized during gate motion. The onboard alarm will remains energized during gate motion. For an sound. For an additional audible or visual display, additional audible or visual display, connect an connect an external buzzer or light (low voltage). external buzzer or light (low voltage). Power ON ON OFF Not used. Tamper ON OFF ON Energizes if gate is manually tampered with by being pushed off of close limit. For an additional audible or visual display, connect an external buzzer or light (low voltage). Cycle Quantity ON ON ON The 1, 2, and 3 LEDs will blink out the cycle count Not used. Feedback* (cycle count is stored on the control board). See below. CYCLE COUNT RED/GREEN LIGHT FUNCTIONALITY * First, note the current Aux Relay switch positions. To determine Red light wired to AUX RELAY 1. Green light wired to AUX RELAY 2. the actual cycles that the gate operator has run (in thousands), set all three Aux Relay switches to the ON setting for Aux Relay AUX RELAY 1 SWITCHES AUX RELAY 2 SWITCHES GATE STATE 1. The Expansion Board’s 1, 2, and 3 LEDs will blink out the 1 OFF 2 OFF 3 OFF 1 ON 2 ON 3 ON cycle count, with 1 LED blinking 1000’s, 2 LED blinking 10,000’s, 3 LED blinking 100,000’s, and simultaneously all Closed Red light OFF* Green light OFF three LED’s blink 1,000,000’s (e.g. 1 LED blinks 3 times, 2 LED Opening Red light ON/Flash Green light OFF blinks 6 times, and 3 LED blinks once. Cycle count is 163,000.). Cycle count displayed is between 1,000 and 9,999,000 cycles. Open Red light OFF Green light ON After servicing, set Aux Relay switches back to their appropriate Closing Red light ON/Flash Green light OFF positions. Cycle count cannot be reset or changed. If under 1,000 cycles the 1, 2, and 3 LEDs will turn on for 10 seconds, Defined Mid Stop n/a n/a then turn off. Undefined Mid NOTE: The expansion board will flash the cycle count 3 times Red light ON Green light OFF Stop then all the LEDs will turn on solid for 10 seconds then turn off. Timer more than 5 Red light OFF Green light ON seconds AUXILIARY RELAY WIRING EXAMPLE Timer less than 5 Red light ON/Flash Green light OFF seconds OPEN CLOSE COM SBC OPN CLS * For red light ON when gate is closed, set switch 1 on AUX RELAY 1 to ON STP COM SHADOW INTERUPT EXIT AUX Relay 1 N.O. AUX Relay 1 N.C. AUX Relay 2 N.O. AUX Relay 2 N.C. Com Com Traffic Light Class 2 Power Source (42 Vdc [34 Vac], 5 A maximum) – AUX RELAY 1 AUX RELAY 2 28 +

WIRE ACCESSORIES TO EXPANSION BOARD PHOTOELECTRIC SENSORS AND EDGE SENSORS The EYES/EDGE terminals are used for connecting entrapment protection devices. At least one external monitored entrapment protection device is required prior to gate movement. Monitored entrapment protection devices should have been installed with the operator at the time of installation. Only ONE monitored device may be connected to each input. A monitored device sends a pulsed signal to the operator so the operator is aware of the device. If the operator does not receive the signal from the device indicating it is working properly, it will not run in that direction. TERMINALS FUNCTIONALITY WIRING EXAMPLE EYE ONLY and COM Open or Close Direction Photoelectric Sensors, the functionality is based T on the switch settings (located next to the terminals) 1 EYE ONLY EYE/ Switch set to CLOSE: gate reverses fully when an obstruction is sensed 2 EDGE EYE/ 3 EDGE Switch set to OPEN: gate reverses 4 seconds when an obstruction is OPEN CLOSE COM sensed SBC EYE/EDGE and COM Open or Close Direction Photoelectric Sensors or Edge Sensor, the functionality is based on the switch settings (located next to the 1 EYE ONLY terminals) 2 EYE/ EDGE 3 EYE/ Switch set to CLOSE: gate reverses fully when an obstruction is sensed EDGE OPEN CLOSE COM Switch set to OPEN: gate reverses 4 seconds when an obstruction is sensed SBC EYE/EDGE and COM Open or Close Direction Photoelectric Sensors or Edge Sensor, the T functionality is based on the switch settings (located next to the 1 EYE ONLY terminals) 2 EYE/ EDGE 3 EYE/ Switch set to CLOSE: gate reverses fully when an obstruction is sensed EDGE OPEN CLOSE COM Switch set to OPEN: gate reverses 4 seconds when an obstruction is sensed SBC CONTROL STATION TERMINALS FUNCTIONALITY WIRING EXAMPLE SBC and COM • Gate command sequence - Open, Stop, Close, Stop, ... • Soft Open ,Soft Close, Soft Stop (maintained switch does not CLOSE COM override external safeties and does not reset alarm condition) O OPEN and COM • Open command - opens a closed gate SBC OPN • Soft open (maintained switch does not override external safeties and does not reset alarm condition) CLS STP • If maintained, pauses Timer-to-Close at OPEN limit COM • Opens a closing gate and holds open an open gate CLOSE and COM • Close command - closes an open gate • Soft close (maintained switch does not override external safeties and does not reset alarm condition) STOP and COM • Stop command - stops a moving gate • Hard stop (maintained switch overrides Open and Close commands and resets alarm condition) • If maintained, pauses Timer-to-Close at OPEN limit • Overrides an Open or Close command 29

WIRE ACCESSORIES TO EXPANSION BOARD LOOPS INPUTS FUNCTIONALITY WIRING EXAMPLE EXIT Loop wire connection for plug-in loop detector when loop is inside secured area near gate. • Open command - opens a closed gate • Soft open (maintained switch does not override external safeties and does not reset alarm condition) • If maintained, pauses Timer-to-Close at OPEN limit SHADOW INTERUPT EXIT • Opens a closing gate and holds open an open gate Shadow Loop Interrupt Loop SHADOW Loop wire connection for plug-in loop detector when loop is positioned under Exit Loop the gate. • Holds open gate at open limit • Disregarded during gate motion • Pauses Timer-to-Close at Open Limit INTERRUPT Loop wire connection for plug-in loop detector when loop is on the outside of the gate. • Holds open gate at open limit • Stops and reverses a closing gate • Pauses Timer-to-Close at Open Limit ADDITIONAL WIRING SAMS WIRING WITH RELAYS NOT ENERGIZED Control Board Barrier Arm Operator BIPART DELAY 4 Exit Input 2 6 OPEN LEFT OPEN RIGHT 8 C HANDING Auxiliary Command NO A COMM LINK B CLASS 2 SUPPLY 500 mA MAX GND 24 VAC ANTENNA CURRENT MOTOR DRIVE RPM & LIMITS ALARM EXP. 24 VAC IN SENSOR ID RESET BOARD Access Device Expansion Board Shadow Input POWER TO MAIN BOARD DEVICE INPUTS EYE 1 ONLY EYE/ 2 EDGE 3 EYE/ EDGE OPEN CLOSE COM SBC OPN CLS STP COM SHADOW INTERUPT EXIT Dipswitch settings for AUX Relay 1: 1-OFF, 2-OFF, 3-ON AUX Relay 1 30

ADDITIONAL WIRING To protect against fire and electrocution: For continued protection against fire: • DISCONNECT power BEFORE installing or servicing operator. • Replace ONLY with fuse of same type and rating. FIELD WIRING CONTROL BOARD BIPART DELAY 4 + 6 + 3-BUTTON 2 + CONTROL OPEN OPEN 8 – N.C. STATION LEFT RIGHT – + FIRE DEPARTMENT HANDING – INTERRUPT LOOP or + EXIT LOOP PHOTOELECTRIC SENSORS for CLOSE cycle – + SHADOW LOOP – + – EDGE SENSOR for CLOSE cycle + – + EDGE SENSOR or PHOTOELECTRIC SENSORS for OPEN cycle Shielded Twisted Pair Cable (Primary/Secondary A link to other gate operator) Ground the shield of the COMM LINK B N.C. cable to the chassis ground of each operator. COM Maglock N.O. (Optional) Solenoid Lock – CLASS 2 SUPPLY ACCESSORY (Optional) 500 mA MAX GND 24 VAC + POWER ANTENNA CURRENT MOTOR DRIVE RPM & LIMITS ALARM EXP. 24 VAC IN SENSOR ID RESET BOARD 24 Vac 500 mA Maximum OR (Not Provided) PLUG-IN LOOP DETECTOR Model LOOPDETLM (Not Provided) NOTE: These switches determine if the corresponding photoelectric sensor or edge HEATER EXPANSION BOARD sensor will function for the OPEN or CLOSE cycle. POWER TO MAIN BOARD EYE + 1 2 ONLY EYE/ + PHOTOELECTRIC SENSORS 3 EDGE EYE/ EDGE + PHOTOELECTRIC SENSORS or – EDGE SENSORS OPEN CLOSE COM JUNCTION BOX SBC + SINGLE BUTTON OPN + CONTROL STATION CLS + STP + 3-BUTTON COM – N.C. CONTROL STATION SHADOW INTERUPT EXIT COM COM N.O. N.C. N.O. N.C. NOTE: These switches control how the Auxiliary Relays will function. AUXILIARY AUXILIARY RELAY 1 RELAY 2 INTERRUPT LOOP SHADOW LOOP L N GND Incoming Power EXIT LOOP 31

PROGRAMMING REMOTE CONTROLS (NOT PROVIDED) A total of 50 Security+ 2.0™ remote controls and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. When programming a third keyless entry to the operator, the first keyless entry will be erased to allow the third keyless entry to be programmed. When the operator’s memory is full it will exit the programming mode and the remote control will not be programmed. The memory will need to be erased before programming any additional remote controls. NOTE: If installing an 86LM to extend the range of the remote controls DO NOT straighten the antenna. There are 3 different options for programming the remote control depending on how you would like the remote control to function. Choose a programming option: OPTION DESCRIPTION PROGRAMMING STEPS Single button as OPEN Program a single button on the 1. Press and release the LEARN button (operator will beep and green XMITTER only remote control for open only. The LED will light). NOTE: The operator will time out of programming mode after 30 Timer-to-Close can be set to close seconds. the gate. 2. Press the OPEN button. 3. Press the remote control button that you would like to program. Single button (SBC) as Program one remote control button 1. Press and release the LEARN button (operator will beep and green XMITTER OPEN, CLOSE, and as an open, close, and stop. LED will light). NOTE: The operator will time out of programming mode after 30 STOP seconds. 2. Press the remote control button that you would like to program. Three separate buttons Program each remote control button 1. Press and release the LEARN button (operator will beep and green XMITTER as OPEN, CLOSE, and as an open, close, and stop. LED will light). NOTE: The operator will time out of programming mode after 30 STOP seconds. 2. Press the OPEN, CLOSE, or STOP button, depending on the desired function. 3. Press the remote control button that you would like to program. The operator will automatically exit learn mode (operator will beep and green XMITTER LED will go out) if programming is successful. To program additional Security+ 2.0™ remote controls or remote control buttons, repeat the programming steps above. Once the remote control has been programmed the operator will operate as follows: When gate is in the closed position, activation of the remote control button will open the gate. During the open cycle another activation of the remote control will stop the gate and the next activation of the remote control will close the gate. When the gate is in the open position, activation of the remote control button will close the gate. If the remote control is activated while the gate is closing, the gate will stop and the next activation will open the gate. NOTICE: This device complies with part 15 of the FCC rules and Industry Canada (IC) licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. 32

PROGRAMMING LIFTMASTER INTERNET GATEWAY (NOT PROVIDED) To program the operator to the LiftMaster Internet Gateway: Program using the learn button on the operator's control board: Program using the reset button on the operator: 1. Connect the ethernet cable to the LiftMaster Internet Gateway and 1. Connect the ethernet cable to the LiftMaster Internet Gateway and the the router. router. 2. Connect power to the LiftMaster Internet Gateway. 2. Connect power to the LiftMaster Internet Gateway. 3. Create an online account by visiting www.myliftmaster.com. 3. Create an online account by visiting www.myliftmaster.com. 4. Register the LiftMaster Internet Gateway. 4. Register the LiftMaster Internet Gateway. 5. Use an internet enabled computer or smartphone to add devices. 5. Use an internet enabled computer or smartphone to add devices. The The LiftMaster Internet Gateway will stay in learn mode for three LiftMaster Internet Gateway will stay in learn mode for three minutes. minutes. 6. Ensure gate is closed. 6. Press the Learn button twice on the primary operator (the operator 7. Give the operator an OPEN command. will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will 8. Within 30 seconds, when the gate is at the open limit press and beep if programming is successful. release the reset button 3 times (on primary gate) to put primary operator into High Band Learn Mode (the operator will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful. The status as shown by the LiftMaster Internet Gateway app will be either “open” or “closed”. The gate operator can then be controlled through the LiftMaster Internet Gateway app. ERASE ALL CODES 1. Press and release the LEARN button (operator will beep and green XMITTER LED will light). 2. Press and hold the LEARN button again until the green XMITTER LED flashes and then release the button (approximately 6 seconds). All remote control codes are now erased. TO REMOVE AND ERASE ALL MONITORED ENTRAPMENT PROTECTION DEVICES 1. Remove the entrapment protection device wires from the terminal block. 2. Press and release the OPEN LEFT and OPEN RIGHT buttons simultaneously. The handing direction LED will remain solid. The other direction LED will begin flashing (entering setup mode). 3. Press the OPEN LEFT and OPEN RIGHT buttons simultaneously to exit. 33

SETTINGS GATE OPERATOR SETUP EXAMPLES The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices. RESIDENTIAL: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns COMMERCIAL/GENERAL ACCESS: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access trumps security concerns COMMERCIAL: Business site where security (gate closed) is important INDUSTRIAL: Large business site where security is required Setting RESIDENTIAL COMMERCIAL/ COMMERCIAL INDUSTRIAL GENERAL ACCESS Quick Close switch Normally set to OFF. Normally set to OFF. Normal Normally set to OFF. Normal Set to ON, so that gate setting Normal gate close (timer or gate close (timer or control). gate close (timer or control). closes immediately after control). vehicle passes CLOSE EYES/ Interrupt loop. Anti-Tail switch setting Normally set to OFF. CLOSE Normally set to OFF. CLOSE Set to ON. In attempt to Set to ON. In attempt to EYES/Interrupt loop EYES/Interrupt loop reverses a prevent vehicle tail-gating, prevent vehicle tail-gating, reverses a closing gate. closing gate. CLOSE EYES/Interrupt loop CLOSE EYES/Interrupt loop pauses a closing gate. pauses a closing gate. Bipart Delay switch For DUAL-GATE site, set to For DUAL-GATE site, set to ON For DUAL-GATE site, set to For DUAL-GATE site, set to setting ON for gate that delays for gate that delays upon ON for gate that delays upon ON for gate that delays upon upon opening. opening. opening. opening. Aux Relay Out – Open Typically not required. Use with SAMS (Sequence 1) Use with SAMS (Sequence 1) Use with SAMS (Sequence Limit Switch Access Management System). Access Management Access Management System). System). 2) Connect “Gate Open” 2) Connect “Gate Open” indicator (e.g. light). indicator (e.g. light). Aux Relay Out – Close Typically not required. Typically not required. Connect “Gate Close/Secure” Connect “Gate Close/Secure” Limit Switch indicator (e.g. light). indicator (e.g. light). Aux Relay Out – Gate Attach alert signal (audible Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Motion or visual alert system). visual alert system). visual alert system). visual alert system). Aux Relay Out – Attach alert signal (audible Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or Pre-Motion Delay or visual alert system). visual alert system). visual alert system). visual alert system). Aux Relay Out – Tamper Attach alert signal (audible Attach alert signal (audible or Attach alert signal (audible or Attach alert signal (audible or (Slide Gates Only) or visual alert system) to visual alert system) to indicate if visual alert system) to visual alert system) to indicate if gate is manually gate is manually tampered with indicate if gate is manually indicate if gate is manually tampered with by being by being pushed off of close tampered with by being tampered with by being pushed off of close limit. limit. pushed off of close limit. pushed off of close limit. Cycle Quantity Feedback Use during servicing only to Use during servicing only to Use during servicing only to Use during servicing only to determine operator cycles. determine operator cycles. determine operator cycles. determine operator cycles. Fire Dept Open input Typically not required. Connect emergency access Typically not required. Typically not required. system (Knox box switch, SOS system, etc.). Heater Accessory The heater keeps the The heater keeps the gearbox The heater keeps the gearbox The heater keeps the gearbox (Model HTRNB) gearbox and batteries at a and batteries at a suitable and batteries at a suitable and batteries at a suitable suitable temperature when temperature when the outside temperature when the outside temperature when the the outside temperature is temperature is below -4°F. The temperature is below -4°F. outside temperature is below below -4°F. The thermostat thermostat MUST be set The thermostat MUST be set -4°F. The thermostat MUST MUST be set between 45°F between 45°F and 60°F to between 45°F and 60°F to be set between 45°F and and 60°F to ensure proper ensure proper gate operation. ensure proper gate operation. 60°F to ensure proper gate gate operation. operation. 34

SETTINGS DUAL GATE SETTINGS NOTE: We recommend that all accessories and board configurations are set on the primary operator. MAIN CONTROL BOARD FEATURE PRIMARY OPERATOR SECONDARY OPERATOR Timer-to-Close Set the TTC dial to desired setting OFF Bi-Part Delay Switch Bi-Part Delay: ON (will open last and close first) Bi-Part Delay: OFF (will open first and close last) Tandem Mode: OFF Tandem Mode: OFF ACCESSORY PRIMARY OPERATOR SECONDARY OPERATOR Remote Controls Program remote controls 1 to 50 to the primary operator. Program remote controls 51 to 100 to the secondary operator LiftMaster Internet Program to primary operator. Gateway Garage and Gate Program to primary operator. Monitor EXPANSION BOARD FEATURE PRIMARY OPERATOR SECONDARY OPERATOR QUICK CLOSE Switch ON OFF ANTI-TAIL Switch ON OFF 35

MAINTENANCE IMPORTANT SAFETY INFORMATION To reduce the risk of SEVERE INJURY or DEATH: • READ AND FOLLOW ALL INSTRUCTIONS. • Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or reverse when an object activates the non- • ANY maintenance to the operator or in the area near the operator contact sensors. After adjusting the force or the limit of travel, retest MUST NOT be performed until disconnecting the electrical power (AC the gate operator. Failure to adjust and retest the gate operator or solar and battery) and locking-out the power via the operator properly can increase the risk of INJURY or DEATH. power switch. Upon completion of maintenance the area MUST be cleared and secured, at that time the unit may be returned to service. • Use the manual disconnect release ONLY when the gate is NOT moving. • Disconnect power at the fuse box BEFORE proceeding. Operator MUST be properly grounded and connected in accordance with • KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. national and local electrical codes. NOTE: The operator should be on Have a qualified service person make repairs to gate hardware. a separate fused line of adequate capacity. • ALL maintenance MUST be performed by a LiftMaster professional. • NEVER let children operate or play with gate controls. Keep the • Activate gate ONLY when it can be seen clearly, is properly adjusted remote control away from children. and there are no obstructions to gate travel. • ALWAYS keep people and objects away from the gate. NO ONE • SAVE THESE INSTRUCTIONS. SHOULD CROSS THE PATH OF THE MOVING GATE. • The entrance is for vehicles ONLY. Pedestrians MUST use separate entrance. To protect against fire and electrocution: For continued protection against fire: • DISCONNECT power (AC or solar and battery) BEFORE installing or • Replace ONLY with fuse of same type and rating. servicing operator. MAINTENANCE Disconnect all power to the operator before servicing. DESCRIPTION TASK CHECK AT LEAST ONCE EVERY MONTH 6 MONTHS Entrapment Protection Devices Check and test for proper operation X Warning Signs Make sure they are present X Manual Disconnect Check and test for proper operation X Drive Chain and Sprockets Check for excessive slack and lubricate X Belt and Pulley Check for excessive slack, wear or damage X Gate Inspect for wear or damage X Accessories Check all for proper operation X Electrical Inspect all wire connections X Chassis Mounting Bolts Check for tightness X Operator Inspect for wear or damage X NOTES: • Severe or high cycle usage will require more frequent maintenance checks. • Limits may have to be reset after any major drive chain adjustments. • If lubricating chain, use only lithium spray. Never use grease or silicone spray. • Over time, the drive chain on the operator will stretch and need to be tightened. To tighten the drive chain adjust either of the two chain eye bolts. The chain should have no more than 1 inch of sag for every 10 feet of chain length. • It is suggested that while at the site voltage readings be taken at the operator. Using a digital voltmeter, verify that the incoming voltage to the operator is within ten percent of the operator’s rating. 36

TROUBLESHOOTING To protect against fire and electrocution: For continued protection against fire: • DISCONNECT power (AC or solar and battery) BEFORE installing or • Replace ONLY with fuse of same type and rating. servicing operator. DIAGNOSTIC CODES TO VIEW THE CODES OPEN, CLOSE, & STOP BUTTONS The codes will show on the diagnostic display. DIAGNOSTICS DISPLAY ...then press and hold the BIPART DELAY OPEN button 4 until "Er" ...then press shows on 2 6 and hold the the display. OPEN OPEN 8 LEFT RIGHT CLOSE button... Press and HANDING hold the STOP button... The operator will show the code sequence number followed by the code number: A COMM LINK CODE SEQUENCE NUMBER B CODE NUMBER The first number shown is the most The second number shown after the recent code (example: "01"). The A SECOND code sequence number is the code CLASS 2 SUPPLY 500 mA MAX display will show the sequence of GND 24 VAC LATER.... itself (31-99, example" "31"). Refer to codes that occurred starting with "01" the chart on the following page for an ANTENNA CURRENT MOTOR DRIVE SENSOR ID RESET RPM & LIMITS ALARM EXP. BOARD 24 VAC IN and going up to code "20". explanation of each code. TO EXIT Press and release the STOP button to exit. The display will also time out after two minutes of inactivity. TO SCROLL THROUGH THE SAVED CODES TO RESET THE CODE HISTORY 1. Press and hold the STOP button for six seconds. The display will show "Er" then "CL" alternately for six seconds. Press the OPEN button 2. Release the STOP button. The code history has now been reset and to cycle to the most recent code ("01"). the display will show "- -" until a new code occurs. Press the CLOSE button 3. Press and release the STOP button to exit. to cycle to the oldest code (up to "20"). The operator will only keep track of up to 20 codes, then will start saving over the oldest codes as new codes occur. 37

TROUBLESHOOTING DIAGNOSTIC CODES continued... Some codes are saved in the code history and some are not. If a code is not saved it will briefly appear on the display as it occurs, then disappear. External Entrapment Inherent Entrapment LiftMaster System Installed System Informational Protection Protection Code Meaning Solution Saved Main control board has experienced an internal Disconnect all power, wait 15 seconds, then reconnect power (reboot). NO 31 failure. If issue continues, replace main control board. Max-Run-Time Exceeded Error Attempt to run and review for duration and obstructions. Max-Run- YES 35 Time can be re-measured by saving one or both of the limits again. Product ID Error Was the control board just replaced? If so, erase limits, enter limit YES 36 setup mode and set limits. If not, disconnect all power, wait 15 seconds, then reconnect power before changing product ID harness. Product ID Failure Unplug product ID harness then plug back in. Disconnect all power, YES 37 wait 15 seconds, then reconnect power before replacing product ID harness. Loop Error - Failure or missing exit loop (SHORT Check loop wiring throughout connection. May be a short in the loop, YES 43 or OPEN - LiftMaster Plug-in Loop Detector only) or an open connection in the loop. Loop Error - Failure or missing shadow loop Check loop wiring throughout connection. May be a short in the loop, YES 44 (SHORT or OPEN - LiftMaster Plug-in Loop or an open connection in the loop. Detector only) Loop Error - Failure or missing interrupt loop Check loop wiring throughout connection. May be a short in the loop, YES 45 (SHORT or OPEN - LiftMaster Plug-in Loop or an open connection in the loop. Detector only) 46 Wireless edge battery low Replace batteries in wireless edge. YES Motor control board fault Relay fault detected in the motor control board. Replace the motor YES 47 control board. Run-Distance Error The limits are less than the minimum requirement or longer than what YES 50 was learned. Check limit positions and proper switch function. Run-distance can be re-learned by setting the handing again. Brownout occurred AC/DC board supply dipped below allowable level. Review power YES 53 supply and wiring. If rebooting, ensure enough time for discharge of power to force a fresh boot. Wireless Second Operator Communication Error Check the second operator for power. If OFF, restore power and try to YES 54 run the system. If powered, deactivate the wireless feature and then re-learn the second operator. 55 System AC Overvoltage Call utility. YES 56 System AC Undervoltage Check wiring and wire gauge to operator. YES Limit Error - Stuck Switch Check switch for proper operation. Check harness for shorts. Replace YES 57 if defective. 58 Limit Error - Wrong Switch Check motor wiring. YES 59 Missing Power Board Check harness for shorts. Check for presence of power board. YES Minimum number of monitored entrapment Review monitored entrapment protection device connections. NO 60 protection devices (one) not installed. CLOSE EYE/INTERRUPT held more than 3 minutes Check CLOSE EYE/INTERRUPT input on main board; check for YES 61 (main board) alignment or obstruction. CLOSE EDGE held more than 3 minutes (main Check CLOSE EDGE input on main board; check for alignment or YES 62 board) obstruction. OPEN EYE/EDGE held more than 3 minutes (main Check OPEN EYE/EDGE input on main board; check for alignment or YES 63 board) obstruction. CLOSE EYE/INTERRUPT held more than 3 minutes Check wired input on expansion board; check for alignment or YES 64 (expansion board) obstruction. CLOSE EYE/EDGE held more than 3 minutes Check wired input on expansion board; check for alignment or YES 65 (expansion board) obstruction. 38

TROUBLESHOOTING DIAGNOSTIC CODES continued... Some codes are saved in the code history and some are not. If a code is not saved it will briefly appear on the display as it occurs, then disappear. External Entrapment Inherent Entrapment LiftMaster System Installed System Informational Protection Protection Code Meaning Solution Saved OPEN EYE/EDGE held more than 3 minutes Check wired input on expansion board; check for alignment or YES 66 (expansion board) obstruction. 67 Wireless edge triggered more than 3 minutes Check wired input for wiring issue or obstruction. YES 68 Wireless edge loss of monitoring Check wireless edge inputs. YES Wireless edge triggered IF an obstruction occurred, no action required. If an obstruction did NO 69 NOT occur, check inputs and wiring. CLOSE EYE/INTERRUPT triggered, causing IF an obstruction occurred, no action required. If an obstruction did NO 70 reversal, preventing close, or resetting TTC (main NOT occur, check alignment, inputs, and wiring. board) CLOSE EDGE triggered, causing reversal, IF an obstruction occurred, no action required. If an obstruction did NO 71 preventing close, or canceling TTC (main board) NOT occur, check alignment, inputs, and wiring. OPEN EYE/EDGE triggered, causing reversal or IF an obstruction occurred, no action required. If an obstruction did NO 72 preventing opening (main board) NOT occur, check alignment, inputs, and wiring. CLOSE EYE/INTERRUPT triggered, causing IF an obstruction occurred, no action required. If an obstruction did NO 73 reversal, preventing close, or resetting TTC NOT occur, check alignment, inputs, and wiring. (expansion board) CLOSE EYE/EDGE triggered, causing reversal and IF an obstruction occurred, no action required. If an obstruction did NO 74 preventing close or canceling TTC (expansion NOT occur, check alignment, inputs, and wiring. board) OPEN EYE/EDGE triggered, causing reversal or IF an obstruction occurred, no action required. If an obstruction did NO 75 preventing opening (expansion board) NOT occur, check alignment, inputs, and wiring. Close input (EYE/EDGE) communication fault from Check inputs and communication method between operators, either YES 80 other operator wired bus or radio. Ensure operator is powered. May have to erase the wireless communication and reprogram the two operators. Open input (EYE/EDGE) communication fault from Check inputs and communication method between operators, either YES 81 other operator wired bus or radio. Ensure operator is powered. May have to erase the wireless communication and reprogram the two operators. Close input (EYE/EDGE) communication fault Check the connections between the main board and the expansion YES 82 (expansion board) board. Open input (EYE/EDGE) communication fault Check the connections between the main board and the expansion YES 83 (expansion board) board. Force Reversal Look for obstruction, if no obstruction, check that the mechanical YES 91 assembly is engaged and free to move. See section on Limit and Force Adjustment, and Obstruction Test. RPM / STALL Reversal Check for obstruction. If no obstruction, check the operator cable YES 93 wiring and that the operator arm is engaged and free to move. Replace RPM assembly. AC motor no start condition Motor start sequence failed. If the gate and motor are NOT moving, or YES moving too slow, check for an obstructed gate, binding in the mechanism, and relay board and start capacitor connections. If the 95 gate and motor ARE moving, failure is due to loss of the encoder signal. Check the encoder cup and sensor on the limit shaft, and wiring. 99 Normal Operation No action required YES 39

TROUBLESHOOTING OPERATOR ALARM If a contact sensor detects an obstruction twice consecutively the alarm will sound (up to 5 minutes) and the operator will need to be reset. If a command is given after the initial 5 minutes the operator will beep. When the inherent force of the operator (RPM/current sensor) detects the following (twice consecutively) the alarm will sound (up to 5 minutes) and the operator will need to be reset: A. The gate is hitting a wall or vehicle. B. The gate does not meet specifications. A B C. Debris is on the gate's track such as mud, rocks, dirt, etc. D. The gate has one or more broken axles or wheels. E. The gate wheel is off the gate rail. Remove any obstructions. Press the reset button to shut off the alarm and reset the operator. After the operator is reset, normal functions will resume. C D E 40

TROUBLESHOOTING TROUBLESHOOTING CHART SYMPTOM POSSIBLE CAUSES SOLUTIONS Operator does not a) No power to control board a) Check AC power run and b) Open fuse b) Check fuses diagnostics display not on. c) Defective control board c) Replace defective control board Control board a) Reset switch is stuck a) Check reset switch powers up, but b) Stop button active or jumper not in place b) Check Stop button is not “stuck on”, or verify that the stop button is a motor does not for stop circuit normally closed circuit, or put a jumper on the stop circuit. run. c) Open or Close input active c) Check all Open and Close inputs for a “stuck on” input d) Entrapment Protection Device active d) Check all Entrapment Protection Device inputs for a “stuck on” sensor e) Vehicle loop detector or probe active e) Check all vehicle detector inputs for a “stuck on” detector f) Defective control board f) Replace defective control board Gate moves, but a) Gate does not move to a limit position a) Use manual disconnect, manually move gate, and ensure gate moves easily cannot set correct b) Gate is too difficult to move limit to limit. Repair gate as needed. limits. b) Gate must move easily and freely through its entire range, limit to limit. c) Limits are set too close (slide gate applications only) Repair gate as needed. c) Ensure the gate moves at least four feet between the OPEN limit and the CLOSE limit. Gate does not fully a) Gate does not move to a limit position a) Use manual disconnect, manually move gate, and ensure gate moves easily open or fully close b) Gate is too difficult to move limit to limit. Repair gate as needed. when setting b) Gate must move easily and freely through its entire range, limit to limit. limits. Repair gate as needed. Operator does not a) Check Open and Close command input LEDs a) Check all Open and Close inputs for a “stuck on” input respond to a wired b) Stop button is active b) Check Stop button is not “stuck on” control/command (example: Open, c) Reset button is stuck c) Check Reset button Close, SBC, etc.) d) Entrapment Protection Device active d) Check all Entrapment Protection Device inputs for a “stuck on” sensor e) Vehicle loop detector or vehicle probe active e) Check all vehicle detector inputs for a “stuck on” detector Operator does not a) Check XMITTER LED when wireless a) Activate wireless control and check XMITTER LED is on. Re-learn wireless respond to a control is active control/transmitter to control board. Replace wireless control as needed. wireless control or b) Stop button is active b) Check Stop button is not “stuck on” transmitter c) Reset button is stuck c) Check Reset button d) Poor radio reception d) Check if similar wired control operates correctly. Check if wireless controls works properly when within a few feet of operator. Check operator’s antenna and antenna wire. Check other wireless controls or devices. Gate stops during a) Control (Open, Close) becoming active a) Check all Open and Close inputs for an active input travel and reverses b) Vehicle loop detector active b) Check all vehicle detector inputs for an active detector immediately. Gate opens, but a) Open control active a) Check all Open inputs for an active input will not close with b) Vehicle loop detector active b) Check all vehicle detector inputs for an active detector transmitter or Timer-to-Close. c) Fire Dept input active c) Check Fire Dept input d) Timer-to-Close not set d) Check Timer-to-Close (TTC) setting e) Close Entrapment Protection Device active e) Check all Entrapment Protection Device inputs for an active sensor Gate closes, but a) Vehicle loop detector active a) Check all vehicle detector inputs for an active detector will not open. Exit loop activation a) Exit vehicle detector setup incorrectly a) Review Exit loop detector settings. Adjust settings as needed. does not cause b) Defective Exit loop detector b) Replace defective Exit loop detector. gate to open. Interrupt loop does a) Vehicle detector setup incorrectly a) Review Interrupt loop detector settings. Adjust settings as needed. not cause gate to b) Defective vehicle loop detector b) Replace defective Interrupt loop detector. stop and reverse. 41

TROUBLESHOOTING TROUBLESHOOTING CHART continued... SYMPTOM POSSIBLE CAUSES SOLUTIONS Shadow loop does a) Vehicle detector setup incorrectly a) Review Shadow loop detector settings. Adjust settings as needed. not keep gate at b) Defective vehicle loop detector b) Replace defective Shadow loop detector. open limit. Obstruction in a) Force adjustment needed a) Refer to the Adjustment section to conduct the obstruction test and perform gate's path does not the proper force adjustment that is needed. cause gate to stop and reverse Photoelectric a) Incorrect photoelectric sensor wiring a) Check photoelectric sensor wiring. Retest that obstructing photoelectric sensor does not b) Defective photoelectric sensor sensor causes moving gate to stop, and may reverse direction. stop or reverse b) Replace defective photoelectric sensor. Retest that obstructing photoelectric gate. sensor causes moving gate to stop, and may reverse direction. Edge Sensor does a) Incorrect edge sensor wiring a) Check edge sensor wiring. Retest that activating edge sensor causes moving not stop or reverse b) Defective edge sensor gate to stop and reverse direction. gate. b) Replace defective edge sensor. Retest that activating edge sensor causes moving gate to stop and reverse direction. Alarm sounds for 5 a) Double entrapment occurred (two a) Check for cause of entrapment (obstruction) detection and correct. Press the minutes or alarm obstructions within a single activation) reset button to shut off alarm and reset the operator. sounds with a command. On dual-gate a) Incorrect Bipart switch setting a) Change setting of both operator’s Bipart switch settings. One operator system, incorrect should have Bipart switch ON (operator that opens second) and the other gate opens first or operator should have Bipart switch OFF (operator that opens first) closes first. Alarm beeps when a) Expansion board setting a) Pre-warning is set to "ON" running. b) Constant pressure to open or close is b) Constant pressure to open or closed is given given Expansion board a) Defective main board to expansion a) Check main board to expansion board wiring. If required, replace wire cable. function not board wiring b) Check wiring to all inputs on expansion board. controlling gate. b) Incorrect input wiring to expansion c) Replace defective expansion board or defective main board board c) Defective expansion board or defective main board Maglock not a) Maglock wired incorrectly a) Check that Maglock is wired to N.C. and COM terminals. Check that Maglock working correctly. has power (do not power maglock from control board accessory power terminals). If shorting lock’s NO and COM wires does not activate Maglock, then replace Maglock or Maglock wiring (refer to Wiring Diagrams). Solenoid lock not a) Solenoid wired incorrectly a) Check that Solenoid is wired to N.O. and COM terminals. Check that Solenoid working correctly. has power (do not power solenoid from control board accessory power terminals). If shorting lock’s NC and COM wires does not activate Solenoid, then replace Solenoid lock or Solenoid wiring (refer to Wiring Diagrams). Quick Close not a) Quick Close setting incorrect a) Check that Quick Close setting is ON working correctly. b) Interrupt loop detector b) Check operation of Interrupt Loop detector c) Defective Expansion board c) Replace defective Expansion board Anti-Tailgating not a) Anti-Tail setting incorrect a) Check that Anti-Tail setting is ON working correctly. b) Interrupt loop detector b) Check operation of Interrupt Loop detector c) Defective Expansion board c) Replace defective Expansion board AUX Relay not a) AUX Relay setting incorrect a) Check AUX Relay switches settings working correctly. b) Check that wiring is connected to either N.O. and COM or to N.C. and COM. b) AUX Relay wiring incorrect c) Defective Expansion board c) Set AUX Relay to another setting and test. Replace defective expansion board. 42

ACCESSORIES INTERNET PROTOCOL ACCESS CONTROL UNIVERSAL REMOTE CONTROLS SECURITY+ 2.0™ LEARNING REMOTE CONTROLS IPAC 813LM 894LT 811LM LIFTMASTER INTERNET GATEWAY 828LM 892LT LIFTMASTER DOOR AND GATE MONITOR Model 829LM PLUG IN LOOP DETECTOR LOOPDETLM HEATER KIT ACCESSORY AC/DC 3 BUTTON CONTROL STATION LIFTMASTER ELITE SERIES HTRNB MAGLOCK PACKAGE 02-103 STOP BUTTON MG1300RLYPKG AEXITP PLATE FOR POST STEEL STAND FOR MOUNTING VGROOVE POWER WHEELS MOUNTING OPERATOR TO CONCRETE PAD MPEL MSEL LONG GATE KIT (NOT SHOWN) Adjusts gate travel up to 51 feet Q160 ENTRAPMENT PROTECTION LiftMaster Monitored Through Beam Photoelectric Sensor (LMTBU) Small Profile Channel - Aluminum (8 ft) (S50CHAL)* LiftMaster Monitored Retro Reflective Photoelectric Sensor (LMRRU) Edge Cutting Tool (ETOOL)** LiftMaster Monitored Wireless Edge Kit (Transmitter and Receiver) Wraparound Square Monitored Edge (4 ft) (WS4)** (LMWEKITU) Wraparound Square Monitored Edge (5 ft) (WS5)** LiftMaster Monitored Wireless Edge Transmitter (LMWETXU) Wraparound Square Monitored Edge (6 ft) (WS6)** Large Profile Monitored Edge (L50)* Wraparound Round Monitored Edge (4 ft) (WR4)** Large Profile Ends Kit (pair) (L50E)** Wraparound Round Monitored Edge (5 ft) (WR5)** Large Profile Channel - PVC (8 ft) (L50CHP)** Wraparound Round Monitored Edge (6 ft) (WR6)** Large Profile Channel - Aluminum (8 ft) (L50CHAL)** Small Profile Monitored Edge (S50)* Small Profile Ends Kit (pair) (S50E)* * Available November 2015 Small Profile Channel - PVC (8 ft) (S50CHP)* ** Available early 2016 43

REPAIR PARTS NOT SHOWN #41 Chain (10 feet) 19-41240D #40 Chain (10 feet) 19-40240D #41 Chain (Nickel Plated) 19-41240D-NP #41 Master Link 19-50307 Cover K77-37708 #40 Master Link 19-50310 Plastic Standoffs for main control board (10 per bag) K77-37683 Wire Harnesses (main board to power board, main board to ground, main board to K77-37693 transformer, and power board to transformer) Wire Harness (main board to expansion board) K94-34778 Reset Switch with ID K94-37468 Hardware Kit (chain bolt and chain bracket) K77-36764 Chain Bolt K07-50637 Drive Belt Limit Switch Assembly K16-4L360 K76-37306 Limit Switch Sprocket 1 HP ONLY K15-35B13AXR Gear Pulley K17-50095 RPM CUP K13-32087 Limit Switch Chain RPM Encoder K19-35056 Board Drive Sprocket K2A0878 K15-41B25LGH Limit Switch Drive Belt K23-50099 K16-4L230 Motor Pulley K17-50098 Limit Switch Capacitor 1/2 HP ONLY Drive Sprocket K29C-65AU2415 Idler Pulley K15-35B17LGF Assembly Transformer K75-50090 Gear Reducer and Brake K21-14182 K32-37349 Alarm K94-37461 Antenna and Power Board,1 Phase Coaxial Cable K1D8402-1CC Motor K77-37638 K20-1050B-1RSX Chassis K73-37199 Expansion Board K1D8387-1CC Electrical Box 1 HP ONLY Assembly K75-37300-1 Motor K20-1050B-1RSX Brake Assembly Main Control Board K77-37710 K1D6761-1CC Dust Guard Junction Box with On/Off K13-34729 Switch and Receptacle K77-37709 44

WARRANTY 7 YEAR RESIDENTIAL / 5 YEAR COMMERCIAL LIMITED WARRANTY LiftMaster (“Seller”) warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of 7 year residential/ 5 year commercial from the date of purchase [and that the SL3000U is free from defect in materials and/or workmanship for a period of 7 year residential/ 5 year commercial from the date of purchase]. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option. ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 7 YEAR RESIDENTIAL/ 5 YEAR COMMERCIAL LIMITED WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE SL3000U, WHICH ARE LIMITED IN DURATION TO THE 7 YEAR RESIDENTIAL/ 5 YEAR COMMERCIAL LIMITED WARRANTY PERIOD FOR THE SL3000U], AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE, INCLUDING BUT NOT LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 45

845 Larch Avenue Elmhurst, Illinois 60126-1196 LiftMaster.com 01-37920 © 2015, LiftMaster – All Rights Reserved


Document Created: 2015-09-14 11:07:47
Document Modified: 2015-09-14 11:07:47
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC