instructions

FCC ID: HBW1D1519

Users Manual

Download: PDF
FCCID_276786

CLICKER Model No. CLT 1 SECTION I - Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt SECTION II - Stanley, Multi-Code, Linear, Moore-O-Matic Universal Garage Door Opener Remote Control Determine if your motor unit/receiver system has DIP switches or a smart-learn button. (Locate the small gray wire antenna. Some 1 2 3 • Determine specific brand and circle above. • Set brand mode switches on clicker remote. • Open existing remote to expose code switches. • Program clicker remote push button. models require removing the light lens.) Step 1 Motor ➡ ✚ ➡ KG KG STANLEY OFF OFF OFF OFF ➡ O Unit & – SMART-LEARN Receiver DIP SWITCHES BUTTON MULTI-CODE ON OFF OFF OFF • If the Receiver has 9 DIP switches Proceed to TYPE A LINEAR/MOORE-O-MATIC OFF ON OFF OFF • If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B LOCK LIGHT • If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE C Step 2 Step 3 - Press and hold both buttons for 5 seconds TYPE The Receiver DIP switch has three positions labeled “+”, “0” 1 2 3 4 5 6 7 8 9 Existing Clicker or until LED begins to Wall Mounted and “-”. The “0” setting cannot be used with the clicker remote. ✚ Remote Remote flash. RANDOM 2-9 Control A 1) Reset switches: 1 to “-” and positions 2 through 9 to a random O DO NOT USE Step 4 - When LED flashes, setting using “+” and the “-”. DO NOT USE THE “O” SETTING. 2) Gather any existing remotes and open to expose the DIP switches. Reset – ➡ Match release both buttons. Remote Control the DIP switch to match the newly coded receiver. Note: some three button remotes do not have a #1 switch. Match the 2 through 9 to the receiver. On three button remotes ➡ Use this existing codes. ➡ Step 5 - Press the button you wish to operate the opener (your choice). button Set extra The clicker remote can be programmed to operate up to 2 garage door openers or gates, the large button is now programmed to activate the door. 3) Test all the newly coded Step 6 - Programming is complete, to test, press the including different brands. All programming is done using the: remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING. switches off. button selected to activate garage door. • Brand switch • Transmitter DIP switch TYPE After determining that the Receiver has a yellow, white or gray 1 2 3 4 5 6 7 8 9 • Transmit push buttons A and B, and LED indicator learn button, 1) Gather any existing remotes and open to expose ✚ RANDOM 2-9 SECTION III - Genie - 9 Code Switch, Genie - 12 Code Switch Preparation B the DIP switches labeled “+”, “0” and “-”. 2) Reset switches: 1 to “-” and positions 2 through 9 to a random setting using “+” and O – DO NOT USE • Open existing remote; determine if there are 9 or 12 code switch settings. the “-”. DO NOT USE THE “0” SETTING, SET ALL REMOTES TO THE SAME SETTING. On three button remotes the large button is 1 2 3 • Set brand mode switches on clicker remote. Determine the BRAND of the existing garage door opener or handheld remote controls. If all ➡ now programmed to activate the door. 3) The recoded remotes must be • Program clicker remote push button. remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the programmed to the receiver. Press and release the smart-learn button. Remote receiver near the flexible wire antenna. Proceed to the SECTION indicated on the BRAND chart Step 1 KG KG push button Then press and hold the existing remote push button for three seconds. below. 4) Test all the newly coded remote controls to be sure that they operate the ➡ GENIE 9 SWITCH OFF OFF ON OFF ➡ Use this door before proceeding to the BRAND MODE SETTING. button Note: If programming to more than one opener, after programming button “A” refer to brand chart, and follow the instructions pertaining to the brand you wish to program into button “B”. GENIE 12 SWITCH ON OFF ON OFF TYPE With this type receiver, the existing remotes do not contain DIP switches. Proceed to BRAND MODE SETTINGS. When the remotes range is diminished, operation is intermittent, or the LED dims, replace the C Step 2 Step 3 - Press and hold battery. Memory is not lost when the battery is removed. Note: Dispose of old batteries both buttons for 5 properly. Existing Clicker seconds or until LED BRAND MODE SETTINGS - Set switches on clicker remote Remote Remote begins to flash. FOR TYPE A AND B FOR TYPE C - Step 1 Step 4 - When LED flashes, ON LED ➡ Match release both buttons. ➡ ➡ UP Position is ON Step 1 GREEN SMART-LEARN existing Step 5 - Press the button you wish to operate the ➡ DOWN Position is OFF Button A Button B BUTTON codes. opener (your choice). ➡ 1 2 3 4 ON Brand Switch ON ON OFF OFF ON ON ON OFF ➡ ➡ Set extra Step 6 - Programming is complete, to test, press the ➡ UP Position is ON switches off. button selected to activate garage door. ➡ DOWN Position is OFF Dip Switch Code switch 1 2 3 4 5 6 7 8 9 10 1112 Existing – OR – settings are Note: Use pen or small screwdriver Remote Battery not used. WARNING to move dip switches. ➡ ORANGE/RED Slide battery Match ➡ SMART-LEARN BUTTON To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: door down & Remove existing codes. Set extra Clicker OFF ON ON OFF ➡ ➡ • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. CAUTION switches off. Remote Code switch • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no settings are obstructions to door travel. BRAND Continue to Step 2. not used. • ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross path of moving gate or door. Proceed to appropriate section. CHART Step 2 - Press and hold both buttons for 5 seconds or until LED begins to flash. NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter are Step 3 - When LED flashes, release both buttons. prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Step 4 - Press the button you wish to operate the opener (your choice). Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause SECTION I - Chamberlain, Sears, LiftMaster, For type A & B, proceed to step 6. For type C, continue on to Step 5. undesired operation. Master Mechanic, DoIt Step 5 1 2 3 A. Press and release B. Press and hold button TECHNICAL SUPPORT: 800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM) SECTION II - Stanley, Multi-code, Linear, Smart-Learn selected in Step 4 for 3 seconds. Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Moore-O-Matic button. Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. KG KG Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. DoIt is a trademark of DoIt Best Corporation. SECTION III - Genie Step 6 - Programming is complete, to test, press the button selected to activate garage door. ©2001, Clicker Corporation 114A2504B All Rights Reserved Printed in Mexico


Document Created: 2001-06-25 14:13:27
Document Modified: 2001-06-25 14:13:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC