Test Report

FCC ID: H8NWLF3020

Test Report

Download: PDF
FCCID_644184

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 FCC 47 CFR PART 15 SUBPART C (Class II Permissive Change) TEST REPORT For Wireless CF Card Model: WLF 3020 Trade Name: ASKEY Issued to Askey Computer Corp. 10F, No. 119, ChienKang Ro., Chung-Ho, Taipei, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. http://www.ccsemc.com.tw service@tw.ccsemc.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 30 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION....................................................................................................3 2. EUT DESCRIPTION ...........................................................................................................................4 3. TEST METHODOLOGY ....................................................................................................................5 3.1 EUT CONFIGURATION ........................................................................................................................5 3.2 EUT EXERCISE....................................................................................................................................5 3.3 GENERAL TEST PROCEDURES.............................................................................................................5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS........................................................6 3.5 DESCRIPTION OF TEST MODES ...........................................................................................................6 4. INSTRUMENT CALIBRATION........................................................................................................7 4.1 MEASURING INSTRUMENT CALIBRATION ......................................................................................7 4.2 MEASUREMENT EQUIPMENT USED.........................................................................................7 5. FACILITIES AND ACCREDITATIONS ..........................................................................................8 5.1 FACILITIES .........................................................................................................................................8 5.2 EQUIPMENT........................................................................................................................................8 5.3 TABLE OF ACCOREDITATIONS AND LISTINGS ....................................................................................9 6. SETUP OF EQUIPMENT UNDER TEST .......................................................................................10 6.1 SETUP CONFIGURATION OF EUT .......................................................................................................10 6.2 SUPPORT EQUIPMENT...............................................................................................................10 7. FCC PART 15.247 REQUIREMENTS.............................................................................................11 7.1 BAND EDGES MEASUREMENT................................................................................................11 7.2 SPURIOUS EMISSIONS ................................................................................................................20 APPENDIX I PHOTOGRAPHS OF TEST SETUP...............................................................................30 Page 2 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 1. TEST RESULT CERTIFICATION Applicant: Askey Computer Corp. Equipment Under Test: Wireless CF Card Trade Name: ASKEY Model: WLF 3020 Date of Test: March 21, 2006 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Gavin Lim Amanda Wu Section Manager Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Page 3 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 2. EUT DESCRIPTION Product Wireless CF Card Trade Name ASKEY Model Number WLF 3020 Model Discrepancy N/A Power Supply Powered from host device Frequency Range 2412 ~ 2462 MHz Transmit Power 0.02W CCK, DQPSK, DBPSK for DSSS Modulation Technique 64QAM, 16QAM, QPSK, BPSK for OFDM 802.11b: 11/5.5/2/1Mbps Transmit Data Rate 802.11g: 54/48/36/24/18/12/9/6Mbps Number of Channels 11 Channels Antenna Specification Wanshih 3907-001100 / PIFA Antenna (External Antenna): 0dBi Change 1: Relocation of antenna connector. Class II Permissive Change Change 2: Removed the printed antenna on the module. Remark: 1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: H8NWLF3020 filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. Page 4 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.247. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209 and 15.247 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. Page 5 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 (2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: WLF 3020) had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in normal link mode only. Channel Low (2412MHz),Mid (2437MHz) and High (2462MHz) were chosen for radiated emissions testing and conducted emissions testing only. Page 6 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement 3M Semi Anechoic Chamber Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A US42510252 07/25/2006 Test Receiver Rohde&Schwarz ESCI 100064 06/28/2006 Switch Controller TRC Switch Controller SC94050010 05/05/2006 4 Port Switch TRC 4 Port Switch SC94050020 05/05/2006 Horn-Antenna TRC HA-0502 06 06/02/2006 Horn-Antenna TRC HA-0801 04 05/05/2006 Horn-Antenna TRC HA-1201A 01 07/04/2006 Horn-Antenna TRC HA-1301A 01 07/04/2006 Bilog- Antenna Sunol Sciences JB3 A030205 03/09/2007 Turn Table Max-Full MFT-120S T120S940302 N.C.R. Antenna Tower Max-Full MFA-430 A440940302 N.C.R. Controller Max-Full MF-CM886 CC-C-1F-13 N.C.R. FCC: 965860 Site NSA CCS N/A IC: IC 6106 09/26/2008 Test S/W LABVIEW (V 6.1) Remark: The measurement uncertainty is less than +/-2.0065dB (30MHz ~ 1GHz), +/-3.0958dB (Above 1GHz) which is evaluated as per the NAMAS NIS 81 and CISPR/A/291/CDV. Page 7 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.199, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Luchu Hsiang, Taoyuan Hsien 338, Taiwan Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” Page 8 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 5.3 TABLE OF ACCOREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo EN 55011, EN 55014-1/2, CISPR 11, CISPR 14-1/2, EN 55022, EN 55015, CISPR 22, CISPR 15, AS/NZS 3548, VCCI V3 (2001), CFR 47, FCC Part 15/18 CNS 13783-1, CNS 13439, CNS 13438, CNS 13803, USA A2LA CNS 14115, EN 55024, IEC 801-2, IEC 801-3, IEC 801-4, IEC/EN 61000-3-2, EIC/EN 61000-3-3, IEC/EN 61000-4-2/3/4/5/6/8/11, EN 50081-1/ EN 61000-6-3, EN 50081-2/EN 61000-6-4, 0824-01 EN 50081-2/EN 61000-6-1: 2001 3/10 meter Open Area Test Sites (93105, 90471) / USA FCC 3M Semi Anechoic Chamber (965860) to perform FCC Part 15/18 measurements 93105, 90471 965860 3/10 meter Open Area Test Sites to perform Japan VCCI conducted/radiated measurements R-393/1066/725/879 C-402/747/912 EN 50081-1/2, EN 50082-1/2, IEC 61000-6-1/2, EN 50091-2, EN 50130-4, EN 55011, EN 55013, EN 55014-1/2, EN 55015, EN 55022, EN 55024, EN 61000-3-2/3, Norway NEMKO EN 61326-1, IEC 61000-4-2/3/4/5/6/8/11, EN 60601-1-2, EN 300 328, EN 300 422-2, EN 301 419-1, ELA 124a EN 301 489-01/03/07/08/09/17, EN 301 419-2/3, ELA 124b EN 300 454-2, EN 301 357-2 ELA 124c EN 300 328, EN 300 220-1, EN 300 220-2, EN 300 220-3, 47 CFR FCC Part 15 Subpart C, Taiwan TAF EN 61000-3-2, EN 61000-3-3, CNS 13439, CNS 13783-1, CNS 14115, CNS 13438, AS/NZS CISPR 22, CNS 13022-1, IEC 61000-4-2/3/4/5/6/8/11, CNS 13022-2/3 CNS 13438, CNS 13783-1, SL2-IS-E-0014 Taiwan BSMI CNS 13439, CNS 14115 SL2-IN-E-0014 SL2-A1-E-0014 SL2-R1-E-0014 SL2-R2-E-0014 SL2-L1-E-0014 3/10 meter Open Area Test Sites (IC 3991-3, IC 3991-4) / Industry IC 3991-3 Canada 3M Semi Anechoic Chamber (IC 6106) to perform Canada IC 3991-4 RSS 212 Issue 1 IC 6106 * No part of this report may be used to claim or imply product endorsement by A2LA or any agency of the US Government. Page 9 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Device Type Brand Model Series No. FCC ID Data Cable Power Cord AC I/P: Unshielded, 1.8m WLAN: ETC094LPD0155 1. Notebook PC Sony PCG-6GFP 00045-578-554-578 N/A DC O/P: Bluetooth: ETC094LPD0156 Unshielded, .8m with a core Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 10 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 7. FCC PART 15.247 REQUIREMENTS 7.1 BAND EDGES MEASUREMENT LIMIT According to §15.247(d), in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see Section 15.205(c)). Test Configuration Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. Page 11 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Band Edges (IEEE 802.11b / CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 12 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 13 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Band Edges (IEEE 802.11b / CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 14 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 15 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Band Edges (IEEE 802.11g / CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 16 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 17 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Band Edges (IEEE 802.11g / CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 18 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 19 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 7.2 SPURIOUS EMISSIONS LIMIT 1. According to §15.209(a), except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (µV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 2. In the emission table above, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (µV/m at 3-meter) (dBµV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 20 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Test Configuration Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp Page 21 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 22 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 TEST RESULTS Below 1 GHz Operation Mode: Normal Link Test Date: March 21, 2006 Temperature: 22°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Result Result Limit Frequency Ant.Pol. Correction Factor Margin (Peak) (QP) (Peak) (QP) (QP) Remark (MHz) (H/V) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dB) 38.08 V 63.00 --- -27.03 35.97 --- 40.00 -4.03 Peak 249.87 V 59.70 --- -30.65 29.05 --- 46.00 -16.95 Peak 414.77 V 57.72 --- -26.43 31.29 --- 46.00 -14.71 Peak 500.45 V 60.98 --- -24.19 36.79 --- 46.00 -9.21 Peak 584.52 V 58.37 --- -23.06 35.31 --- 46.00 -10.69 Peak 995.15 V 50.97 --- -18.64 32.33 --- 54.00 -21.67 Peak 215.92 H 68.98 --- -31.58 37.40 --- 43.50 -6.10 Peak 278.97 H 66.36 --- -29.25 37.10 --- 46.00 -8.90 Peak 319.38 H 68.24 --- -28.89 39.34 --- 46.00 -6.66 Peak 416.38 H 59.47 --- -26.43 33.04 --- 46.00 -12.96 Peak 500.45 H 53.43 --- -24.19 29.24 --- 46.00 -16.76 Peak 917.55 H 55.27 --- -19.41 35.86 --- 46.00 -10.14 Peak Remark: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m). Page 23 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Above 1 GHz Operation Mode: TX / IEEE 802.11b / CH Low Test Date: March 21, 2006 Temperature: 22°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant.Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 1880.00 V 55.40 --- -11.63 43.77 --- 74.00 54.00 -10.23 Peak 4825.00 V 59.99 42.93 -7.80 52.19 35.13 74.00 54.00 -18.87 Average N/A 1860.00 H 54.49 --- -11.75 42.73 --- 74.00 54.00 -11.27 Peak 4825.00 H 60.94 43.73 -7.80 53.14 35.93 74.00 54.00 -18.07 Average N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 24 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Operation Mode: TX / IEEE 802.11b / CH Mid Test Date: March 21, 2006 Temperature: 22°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant.Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2090.00 V 54.85 --- -10.79 44.05 --- 74.00 54.00 -9.95 Peak 4875.00 V 56.26 --- -7.79 48.48 --- 74.00 54.00 -5.52 Peak N/A 1333.33 H 55.22 --- -14.25 40.97 --- 74.00 54.00 -13.03 Peak 4875.00 H 53.86 --- -7.79 46.07 --- 74.00 54.00 -7.93 Peak 13500.00 H 42.34 --- -2.17 40.17 --- 74.00 54.00 -13.83 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 25 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Operation Mode: TX / IEEE 802.11b / CH High Test Date: March 21, 2006 Temperature: 22°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant.Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 1906.67 V 55.04 --- -11.47 43.57 --- 74.00 54.00 -10.43 Peak 4925.00 V 52.43 --- -7.78 44.66 --- 74.00 54.00 -9.34 Peak 7391.67 V 44.71 --- -5.58 39.13 --- 74.00 54.00 -14.87 Peak 8866.67 V 41.68 --- -2.68 39.00 --- 74.00 54.00 -15.00 Peak N/A 1433.33 H 55.24 --- -14.05 41.19 --- 74.00 54.00 -12.81 Peak 4925.00 H 51.48 --- -7.78 43.71 --- 74.00 54.00 -10.29 Peak 14383.33 H 42.65 --- -2.21 40.44 --- 74.00 54.00 -13.56 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 26 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Operation Mode: TX / IEEE 802.11g / CH Low Test Date: March 21, 2006 Temperature: 25°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant. Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2246.67 V 54.97 --- -10.59 44.38 --- 74.00 54.00 -9.62 Peak 4825.00 V 45.71 --- -7.80 37.92 --- 74.00 54.00 -16.08 Peak N/A 2543.33 H 55.94 --- -10.22 45.73 --- 74.00 54.00 -8.27 Peak 4825.00 H 44.84 --- -7.80 37.05 --- 74.00 54.00 -16.95 Peak 7308.33 H 44.40 --- -5.64 38.76 --- 74.00 54.00 -15.24 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 27 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Operation Mode: TX / IEEE 802.11g / CH Mid Test Date: March 21, 2006 Temperature: 25°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant. Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 1450.00 V 55.67 --- -14.02 41.65 --- 74.00 54.00 -12.35 Peak 3175.00 V 43.43 --- -9.50 33.93 --- 74.00 54.00 -20.07 Peak N/A 4208.33 H 43.62 --- -8.22 35.41 --- 74.00 54.00 -18.59 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 28 Rev. 00

Compliance Certification Services Inc. Report No.: 60314202-RP1 FCC ID: H8NWLF3020 Date of Issue: March 29, 2006 Operation Mode: TX / IEEE 802.11g / CH High Test Date: March 21, 2006 Temperature: 25°C Tested by: Rex Lai Humidity: 56 % RH Polarity: Ver. / Hor. Reading Reading Correction Result Result Limit Limit Frequency Ant. Pol. Margin (Peak) (Average) Factor (Peak) (Average) (Peak) (Average) Remark (MHz) (H/V) (dB) (dBuV) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 4758.33 V 44.38 --- -7.81 36.57 --- 74.00 54.00 -17.43 Peak 7416.67 V 43.20 --- -5.56 37.64 --- 74.00 54.00 -16.36 Peak N/A 1153.33 H 56.02 --- -14.61 41.42 --- 74.00 54.00 -12.58 Peak 6175.00 H 44.76 --- -7.01 37.75 --- 74.00 54.00 -16.25 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark result (dBuV/m) – Average limit (dBuV/m). Page 29 Rev. 00


Document Created: 2006-04-04 14:54:52
Document Modified: 2006-04-04 14:54:52
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC