Users Manual

FCC ID: H8NHNH010D75

Users Manual

Download: PDF
FCCID_59510

ASKEY COMPUTER CORP. SUBJECT : Product Specification MODEL : HNH010-D75 REV : 02 RL DATE : AUG-11-1999 PAGES : 6 CONTENTS : Prepared By : Reviewed By : Approval By :

TABLE OF CONTENTS Introduction Product Specification Function Requirement - Home LAN Communication - Data Communication - Fax communication - Diagnostics Capabilities - Modem Operational Characteristics - Operating System - Compatibility Requirement - Customer Requirements Interface Specification - DTE Interface - Telephone Network Interface - Power Management Interface Product Reliability Operating Environment Mechanical Characteristics - Dimensions - Flammability Regulatory Standard Compliance

Introduction The specification defines the product requirement for the HNH010-D75 modem module. The modem is a Home LAN + Controller-less design using Conexant RS7112/RHP56LD chipset for PCI interface that provides HomePNA, Data and Fax communication features described as following: Product Specification Function Requirement - Home LAN Communication * Protocols : HomePNA 1.0 Specification * Data Speed : 1Mbps data rate * AFE type: Integrated AFE - Data Communication * Protocols : V.90, V.34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, Bell212A and Bell103 * Error Correction : V.42, MNP2-4 * Data Compression : V.42bis, MNP5 * Command set : Enhanced TIA/EIA-602 command set * DTE Speed : 300 to 115200 bps * Data Format : 10 bits, including start bit, stop bit and parity - Fax Communication * Protocols : V.17, V.29, V.27ter, V.21 ch 2 * Fax type : Group 3 compatible * Command set : TIA/EIA-578 class 1 Fax command set - Diagnostics Capabilities * Analog loopback and analog loopback selftest * Remote digital loopback and remote digital loopback selftest

- Modem operational Characteristics Under FCC Spec. * Transmit Level : less than -11 dbm +/- 2 dBm W/O AGC * Receive sensitivity : -35 dBm +/- 2 dBm Under V.34 mode * Guard Tone : 550 or 1800 Hz +/- 20 Hz * Answer Tone : CCITT 2100 Hz +/- 15 Hz * Bell 2225 Hz +/- 10 Hz * Dialing Method Under FCC: 1) Tone dialing (A) Symbols : 1 2 3 4 5 6 7 8 9 0 # * A B C D (B) Frequency : within +/- 1.5% (C) High Group Level : -6 dBm +/- 2 dBm (D) Low Group Level : -8 dBm +/- 2 dBm 2) Pulse dialing (A) Duration : 10 pps +/- 2 pps (B) M/B ration : 39 +/- 10% or 33 +/- 10% * Call Progress Tone Detection : 340Hz ~ 640 Hz @ 0 dBm ~ -38 dBm * Ring detection : 15Hz~68Hz, 30Vrms~150 Vrms, 1~3 sec ON/3~5 sec OFF * Modem bit error rates : error less than 10E-5 at nominal SNR * Power consumption : 1) Sleep mode : 50mW @ +5VDC +/- 5% 2) Idle mode : 500mW @ +5VDC +/- 5 % 3) Connection mode : 800mW @ +5VDC +/- 10 % - Operating Systems * Windows 2K * Windows 95 & OSR2 * Windows 98 * Windows NT 4.0 * Windows NT 5.0 - Compatibility Requirements The modem must reliably connect to popular data modems and fax machines. - Customer requirements * Auto dial and auto answer * ACPI power management * User selectable country setting through driver

Interface Specification - DTE interface The modem provides PCI bus as following definition. *PCI SIG Specification 2.2 *PCI SIG Specification 2.1 *Meets PC99 Requirements *5V and VAUX power Auto switch - Telephone Network Interface The RJ-11C type telephone jack. - Power Management Interface *ACPI power management meets PC99 *PCI SIG Power Management Specification 1.1A *D3 cold function supports *Supports PME signal to wake up the system when Receives ring signal. Product Reliability The calculated MTBF shall be greater than 50000 hours. The calculation shall be made under following assumptions : Ambient Temperature : 40 degree C, inlet air temperature Operating Environment * Operating temperature : 0 to 50 degree C * Shipping and storage temperature : -40 to 65 degree C * Operating Humidity : 8% to 80% none-condensing * Altitude : 0 to 10000 feet

Mechanical Characteristics - Dimensions The modem assembly consists of one 2 layer PCB assembly. The modem is approximately 68.5mm x 145mm. - Assembly The polymeric materials used in the modem assembly meet of exceed the requirement of UL 94. Regulatory standards compliance The product must compliance with all the following regulatory standards : * UL1950 3rd Edition * CSA * DOC * FCC part 15 and FCC part 68 * JATE


Document Created: 2019-10-28 11:38:06
Document Modified: 2019-10-28 11:38:06
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC