Part 2

FCC ID: H8NBTM010

Test Report

Download: PDF
FCCID_329924

FCC ID: H8NBTM010 4.6 MAXIMUM PEAK OUTPUT POWER –USING SPECTRUM ANALYZER 4.6.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT The Limit of Maximum Peak Output Power Measurement is 30dBm. 4.6.2 INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 July 24, 2003 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF920318R02 44 Issued: April 19, 2003

FCC ID: H8NBTM010 4.6.3 TEST PROCEDURES 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency within its operating range. Set a reference level on the measuring instrument equal to the highest peak value. 3. The center frequency of the spectrum analyzer is set to the fundamental frequency and using 3 MHz RBW and 3 MHz VBW. 4. Measure the frequency difference of two frequencies that were attenuated 20dB from the reference level. Record the frequency difference as the emission bandwidth. 5. Repeat above procedures until all frequencies measured were complete. 4.6.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF920318R02 45 Issued: April 19, 2003

FCC ID: H8NBTM010 4.6.5 TEST SETUP EUT SPECTRUM ANALYZER For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 4.6.6 EUT OPERATING CONDITION The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel frequencies individually. Report No.: RF920318R02 46 Issued: April 19, 2003

FCC ID: H8NBTM010 4.6.7 TEST RESULTS Output Power to Antenna: CHANNEL PEAK POWER PEAK POWER CHANNEL FREQUENCY OUTPUT LIMIT PASS/FAIL (MHz) (dBm) (dBm) 0 2402 4.08 30 PASS 39 2441 3.11 30 PASS 78 2480 1.98 30 PASS Report No.: RF920318R02 47 Issued: April 19, 2003

FCC ID: H8NBTM010 Channel 0 Report No.: RF920318R02 48 Issued: April 19, 2003

FCC ID: H8NBTM010 Channel 39 Report No.: RF920318R02 49 Issued: April 19, 2003

FCC ID: H8NBTM010 Channel 78 Report No.: RF920318R02 50 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7 RADIATED EMISSION MEASUREMENT 4.7.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF920318R02 51 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. CALIBRATED UNTIL * HP Spectrum Analyzer 8590L 3544A01176 May 13, 2003 * HP Preamplifier 8447D 2944A08485 Apr. 29, 2003 * HP Preamplifier 8449B 3008A01201 Dec. 01, 2003 * HP Preamplifier 8449B 3008A01292 Aug. 07, 2003 *Spectrum Analyzer 8593E 3926A04191 Mar. 24, 2004 *Test Receiver ESI7 838496/016 Feb. 23, 2004 SCHAFFNER Tunable VHBA 9123 459 Dipole Antenna Nov. 22, 2003 SCHWARZBECK Tunable UHA 9105 977 Dipole Antenna * CHASE BILOG Antenna CBL6112A 2221 Aug. 02, 2003 * SCHWARZBECK Horn BBHA9120-D1 D130 July 03, 2003 Antenna * EMCO Horn Antenna 3115 9312-4192 Apr. 09, 2003 * EMCO Turn Table 1060 1115 NA * SHOSHIN Tower AP-4701 A6Y005 NA ADT_Radiated * Software NA NA _V5.09 * ANRITSU RF Switches MP59B M35046 Jul. 11. 2003 * TIMES RF cable LMR-600 CABLE-ST5-01 Jul. 11. 2003 NOTE: 1. The calibration interval of the above test instruments is 12 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. “*” = These equipment are used for the final measurement. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The test was performed in ADT Open Site No. 5. 5. The VCCI Site Registration No. is R-1039. Report No.: RF920318R02 52 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re- tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 300 Hz for Average detection (AV) at frequency above 1GHz. 4.7.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF920318R02 53 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. Report No.: RF920318R02 54 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7.6 TEST RESULTS Digital Portion: EUT BLUETOOTH MODEM MODEL BTM010 FREQUENCY MODE Channel 78 Below 1000 MHz RANGE INPUT POWER DETECTOR 120Vac, 60 Hz Quasi-Peak (SYSTEM) FUNCTION ENVIRONMENTAL 25 deg. C, 60%RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 151.00 27.0 QP 43.50 -16.50 1.15 H 65 15.60 11.40 2 244.07 26.0 QP 46.00 -20.00 1.33 H 1 10.90 15.00 3 265.42 31.3 QP 46.00 -14.70 1.53 H 239 14.70 16.60 4 287.51 30.2 QP 46.00 -15.80 1.40 H 110 13.60 16.60 5 331.78 28.6 QP 46.00 -17.40 1.46 H 3 11.20 17.40 6 661.76 34.5 QP 46.00 -11.50 1.20 H 12 11.60 22.90 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 152.51 35.3 QP 43.50 -8.20 1.43 V 159 24.00 11.30 2 184.32 33.0 QP 43.50 -10.50 1.00 V 6 22.30 10.70 3 250.01 26.6 QP 46.00 -19.40 1.55 V 32 11.00 15.60 4 265.44 32.2 QP 46.00 -13.80 1.23 V 6 15.60 16.60 5 287.54 34.6 QP 46.00 -11.40 1.02 V 3 18.00 16.60 6 294.91 33.1 QP 46.00 -12.90 1.00 V 78 16.40 16.70 7 309.64 31.2 QP 46.00 -14.80 1.14 V 3 14.20 17.00 8 320.70 30.1 QP 46.00 -15.90 1.13 V 102 13.00 17.20 9 331.77 33.2 QP 46.00 -12.80 1.16 V 5 15.80 17.40 NOTE: 1. Emission level = Raw value - Correction Factor 2. Correction Factor = Pre-Amp. Factor - Ant. Factor - Cable loss (Pre-Amp. Factor = 0, when a Pre-Amplifier is not used for the test.) 3. Margin value = Emission level - Limit value 4. The other emission levels were very low against the limit. Report No.: RF920318R02 55 Issued: April 19, 2003

FCC ID: H8NBTM010 4.7.7 TEST RESULTS RF Portion : EUT BLUETOOTH MODEM MODEL BTM010 FREQUENCY MODE Channel 0 Above 1000 MHz RANGE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 60%RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 36.7 PK 74.00 -37.30 1.04 H 38 10.50 26.20 2 *2402.00 98.1 PK 1.29 H 80 68.50 29.60 2 *2402.00 68.1 AV 1.29 H 80 33.80 26.20 3 4804.00 46.7 PK 74.00 -27.30 1.00 H 305 11.80 34.90 4 7206.00 59.3 PK 74.00 -14.70 1.77 H 122 18.90 40.40 4 7206.00 29.3 AV 54.00 -24.70 1.77 H 122 -1.00 29.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 37.7 PK 74.00 -36.30 1.49 V 52 11.50 26.20 2 *2402.00 92.9 PK 1.22 V 54 63.30 29.60 2 *2402.00 62.9 AV 1.22 V 54 27.30 26.20 3 4804.00 49.6 PK 74.00 -24.40 1.34 V 360 14.70 34.90 4 7206.00 61.4 PK 74.00 -12.60 1.34 V 294 21.00 40.40 4 7206.00 31.4 AV 54.00 -22.60 1.34 V 294 -0.70 29.60 NOTE: 1. Emission level = Raw value - Correction Factor 2. Correction Factor = Pre-Amp. Factor - Ant. Factor - Cable loss (Pre-Amp. Factor = 0, when a Pre-Amplifier is not used for the test.) 3. Margin value = Emission level - Limit value 4. “ * “ : Fundamental frequency 5. The other emission levels were very low against the limit. 6. The DH5 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*5 per 247 ms per channel. Therefore, the duty cycle be equal to: 20log(3.125/100)= -30dB 7. Average value = peak reading –20log(duty cycle) Report No.: RF920318R02 56 Issued: April 19, 2003

FCC ID: H8NBTM010 EUT BLUETOOTH MODEM MODEL BTM010 FREQUENCY MODE Channel 39 Above 1000 MHz RANGE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 60%RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 39.1 PK 74.00 -34.90 1.39 H 9 12.90 26.20 2 *2441.00 95.8 PK 1.49 H 234 66.10 29.70 2 *2441.00 65.8 AV 1.49 H 234 33.20 26.20 3 4882.00 52.0 PK 74.00 -22.00 1.03 H 174 16.80 35.20 3 4882.00 22.0 AV 54.00 -32.00 1.03 H 174 -1.40 29.70 4 7323.00 57.4 PK 74.00 -16.60 1.70 H 54 16.90 40.50 4 7323.00 27.4 AV 54.00 -26.60 1.70 H 54 -1.00 35.20 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 39.2 PK 74.00 -34.80 1.46 V 342 13.00 26.20 2 *2441.00 93.5 PK 1.08 V 226 63.80 29.70 2 *2441.00 63.5 AV 1.08 V 226 32.80 26.20 3 4882.00 50.5 PK 74.00 -23.50 1.60 V 108 15.30 35.20 3 4882.00 20.5 AV 54.00 -33.50 1.60 V 108 -1.50 29.70 4 7323.00 55.8 PK 74.00 -18.20 1.29 V 325 15.20 40.50 4 7323.00 25.8 AV 54.00 -28.20 1.29 V 325 -1.50 35.20 NOTE: 1. Emission level = Raw value - Correction Factor 2. Correction Factor = Pre-Amp. Factor - Ant. Factor - Cable loss (Pre-Amp. Factor = 0, when a Pre-Amplifier is not used for the test.) 3. Margin value = Emission level - Limit value 4. “ * “ : Fundamental frequency 5. The other emission levels were very low against the limit. 6. The DH5 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*5 per 247 ms per channel. Therefore, the duty cycle be equal to: 20log(3.125/100)= -30Db 7. Average value = peak reading –20log(duty cycle) Report No.: RF920318R02 57 Issued: April 19, 2003

FCC ID: H8NBTM010 EUT BLUETOOTH MODEM MODEL BTM010 FREQUENCY MODE Channel 78 Above 1000 MHz RANGE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 60%RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 37.7 PK 74.00 -36.30 1.15 H 35 11.50 26.20 2 *2480.00 94.4 PK 1.93 H 284 64.50 29.90 2 *2480.00 64.4 AV 1.93 H 284 33.00 26.20 3 4960.00 51.8 PK 74.00 -22.20 1.02 H 74 16.30 35.50 3 4960.00 21.8 AV 54.00 -32.20 1.02 H 74 1.90 29.90 4 7440.00 55.3 PK 74.00 -18.70 1.57 H 56 14.60 40.70 4 7440.00 25.3 AV 54.00 -28.70 1.57 H 56 -1.80 35.50 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.00 40.7 PK 74.00 -33.30 1.13 V 39 14.50 26.20 2 *2480.00 91.7 PK 1.82 V 150 61.80 29.90 2 *2480.00 61.7 AV 1.82 V 150 32.50 26.20 3 4960.00 52.0 PK 74.00 -22.00 1.01 V 330 16.50 35.50 3 4960.00 22.0 AV 54.00 -32.00 1.01 V 330 -0.40 29.90 4 7440.00 57.7 PK 74.00 -16.30 1.31 V 36 17.00 40.70 4 7440.00 27.7 AV 54.00 -26.30 1.31 V 36 -1.40 35.50 NOTE: 1. Emission level = Raw value - Correction Factor 2. Correction Factor = Pre-Amp. Factor - Ant. Factor - Cable loss (Pre-Amp. Factor = 0, when a Pre-Amplifier is not used for the test.) 3. Margin value = Emission level - Limit value 4. “ * “ : Fundamental frequency 5. The other emission levels were very low against the limit. 6. The DH5 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*5 per 247 ms per channel. Therefore, the duty cycle be equal to: 20log(3.125/100)= -30dB 7. Average value = peak reading –20log(duty cycle) Report No.: RF920318R02 58 Issued: April 19, 2003

FCC ID: H8NBTM010 4.8 BAND EDGES MEASUREMENT 4.8.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100KHz RB). 4.8.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 July 24, 2003 NOTES: The calibration interval of the above test instruments is 12 months. And the calibrations are traceable to NML/ROC and NIST/USA. 4.8.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 kHz bandwidth from band edge. The band edges was measured and recorded. 4.8.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF920318R02 59 Issued: April 19, 2003

FCC ID: H8NBTM010 4.8.5 EUT OPERATING CONDITION The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel frequencies individually. 4.8.6 TEST RESULTS The spectrum plots are attached on the following 2 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). NOTE: The band edge emission plot on the following first page shows 53.74dB delta between carrier maximum power and local maximum emission in restrict band (2.390GHz). The emission of carrier strength list in the test result of channel 0 at the item 4.7.7 is 68.1dBuV/m, so the maximum field strength in restrict band is 68.1- 53.74=14.36dBuV/m which is under 54 dBuV/m limit. NOTE: The band edge emission plot on the following second page shows 58.77dB delta between carrier maximum power and local maximum emission in restrict band (2.500GHz). The emission of carrier strength list in the test result of channel 78 at the item 4.7.7 is 64.4dBuV/m, so the maximum field strength in restrict band is 64.4- 58.77=5.63dBuV/m which is under 54 dBuV/m limit. Report No.: RF920318R02 60 Issued: April 19, 2003

FCC ID: H8NBTM010 Report No.: RF920318R02 61 Issued: April 19, 2003

FCC ID: H8NBTM010 Report No.: RF920318R02 62 Issued: April 19, 2003

FCC ID: H8NBTM010 4.9 ANTENNA REQUIREMENT 4.9.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6 dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 4.9.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is Dipole Antenna and used Reversed SMA antenna connector. The maximum Gain of this antenna is only 1dBi. Report No.: RF920318R02 63 Issued: April 19, 2003

FCC ID: H8NBTM010 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF920318R02 64 Issued: April 19, 2003

FCC ID: H8NBTM010 RADIATED EMISSION TEST Report No.: RF920318R02 65 Issued: April 19, 2003

FCC ID: H8NBTM010 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP Germany TUV Rheinland Japan VCCI New Zealand MoC Norway NEMKO R.O.C. BSMI, DGT, CNLA Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Lin Kou EMC Lab: Hsin Chu EMC Lab: Tel: 886-2-26052180 Tel: 886-35-935343 Fax: 886-2-26052943 Fax: 886-35-935342 Lin Kou Safety Lab: Lin Kou RF&Telecom Lab Tel: 886-2-26093195 Tel: 886-3-3270910 Fax: 886-2-26093184 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF920318R02 66 Issued: April 19, 2003


Document Created: 2003-05-02 17:59:32
Document Modified: 2003-05-02 17:59:32
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC