Manual

FCC ID: H8N-WLU6120

Users Manual

Download: PDF
FCCID_1144927

ASKEY WIFI Module WLU6120-D01(RoHS) WLU6121-D01(RoHS) OPERATION MANUAL DRAFT_V01

1. Product Spec. Chip Set Atheros AR9271 Operation Voltage 3.3V Network Standards IEEE802.11b, IEEE802.11g and IEEE802.11n Modulation Techniques BPSK, QPSK, CCK, DBPSK, DQPSK, 16QAM, 64QAM Modulation Technology OFDM, CCK, DSSS, MIMO(1T1R) 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6Mbps Data Rate 802.11n: HT20: 65, 58.5, 52, 39, 26, 19.5, 13, 6.5Mbps(MCS7-0) HT40: 135, 121.5, 108, 81, 54, 40.5, 27, 13.5Mbps(MCS7-0) Network Architectures Infrastructure and Ad Hoc Operating Frequencies 2.412~2.462 GHz Antenna 1: RF chain 0 for transmit and receive Antenna Type Antenna 2: RF chain 1 diversity antenna for receive 11b: 16dBm 11g: 16dBm , 15dBm@54M RF output power 11n HT20: 16dBm, 13dBm@MCS6, 12dBm@MCS7 HT40:16dBm, 15dBm@MCS5, 11dBm@MCS6, 10dBm@MCS7 802.11b: -82dBm@11Mbps and PER<8% Receiver sensitivity 802.11g: -65dBm@54Mbps and PER<10% (PER<10%) 802.11n: HT20-654dBm, HT40:-62dBm Tx: 1115mW continuous transmitter 11b @2.4GHz;(1M, 18dBm, 1TX, IEEE802.11b) Tx: 1181mW continuous transmitter 11g @2.4GHz;(6M, 18dBm, 1TX, IEEE802.11g) Tx: 1184mW continuous transmitter 11n @2.4GHz;(MCS0, 20MHz, IEEE802.11n) Tx: 1207mW continuous transmitter 11nb @2.4GHz;( MCS0, 40MHz, Power Consumption 1TX, IEEE802.11n) Rx: 376mW continuous transmitter 11g @2.4GHz;(1M, IEEE802.11b) Rx: 379mW continuous transmitter 11g @2.4GHz;(6M, IEEE802.11g) Rx: 376mW continuous transmitter 11n @2.4GHz;(MCS0, 20MHz, IEEE802.11n) Tx: 475mW continuous transmitter 11nb @2.4GHz;( MCS0, 40MHz, 1TX, IEEE802.11n) Temperatures(AMBIENT) Operation: 0~60℃, Storage:-20~70℃ Humidity(non-condensing) 0~95%RH Ant1: PCB Antenna/ Gain:2.86 Ant2: PCB Antenna/ Gain:2.74 Antenna Ant3: PCB Antenna/ Gain:2.19 Ant4: PCB Antenna/ Gain:2.50 Ant5: PCB Antenna/ Gain:0.77

2. Setup Operation A. Install WLU6120-D01(RoHS) / WLU6121-D01(RoHS) into the system. B. Setup Driver as blow windows:

Found New Hardware Wizard FHeaso chasse your soarch and natalation ptions ® eachfrine bax averntase beatons U e chck hss belcwt ns ar onh dfiaeac ichnsuden e sutbeanrencralomeda The bes diverfon wb naales C Seant enovaile meda fooy.CORONL) bnldetigeaton in the each 5018ANCL1035.NSTALLT 70 femndotc O ont eauh Ivilctsethe dvetot Chaesthsenton o scetthedevee diverfon a i. Windonsdoes tncse tat the diveryouchoose wilo ie bax natch oryobactrace Hardware Instllation Ts sctvar yoie atain forthshactore AbwcsARS271 Vess NavoteAduter ho not assed WndonLogetesingto vedyts consatbiy wthWds 29. Te me uinnsie s mootaet) Cortinaing your inatalaion of this oltware may inpair or destabilze the coreet opention o your ytem alther imnediately or in the ftire; Micronat srongly recommens that you top this nstalation now and eentact the hartirare vendorfor oltware that has possed Windows Logo testing s


USA - Federal Communications Commission (FCC) FCC Radiation Exposure Statement CAUTION: . • The radiated output power of WiFi Module 802.11bgn devices is far below the FCC radio frequency exposure limits. Nevertheless, WiFi Module 802.11bgn devices should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20 cm between you (or any other person in the vicinity) and the antenna that is built into the notebook. Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that might cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment might cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures: . • Relocate this device. . • Increase the separation between the device and the receiver. . • Connect the device into an outlet on a circuit different from that of other electronics. . • Consult the dealer or an experienced radio technician for help. NOTE: . • WiFi Module 802.11bgn must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by ASKEY could void your authority to operate the equipment. . • The devices must not be co-located or operating in conjunction with any other antenna or transmitter.

Canada. Industry Canada (IC) This device complies with RSS210 of Industry Canada. CAUTION: Exposure to Radio Frequency Radiation. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from health Canada’s website www.hc-sc.ca/rpb. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. This device is intended only form OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in visible area with the following: Contains TX FCC ID: H8N-WLU6120; IC: 1353A-WLU6120 End Product Manual Information The user manual for end users must include the following information in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


Document Created: 2009-07-27 12:05:37
Document Modified: 2009-07-27 12:05:37
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC