User Manual

FCC ID: H8N-WLL6540

Users Manual

Download: PDF

FCCID_2805322

4. Feature:
The WLL6540(RoHS) module integrates a 1T1R 802.11n WI-FI radio, 1-Port fast
Ethernet PHY, USB2.0 host, I2S/PCM and 4 GPIO. This module embedded high
performance process a CPU can process advanced applications effortlessly, such
as routing, security and VoIP; and includes variety of applications, such as a USB
port for accessing external storage.

◆Embedded MIPS24KEc（575/580MHz）with 64KB I-Cache and 32 KB D- Cache
◆1T1R 2.4GHz with 150Mbps PHY data rate
◆Legacy 802.11b/g and 802.11n modes，20/40MHz channel bandwidth
◆802.11v
◆1-port 10/100 FE PHY
◆Iot (Internet of Things)
◆Green AP/STA
◆16 Multiple BSSID
◆AES128/256-CBC
◆WEP64/128/, TKIP, AES, WPA, WPA2, WAPI
◆WPS: PBC, PIN
◆ Small size 34mm*28mm

5. How to use this module
 Install application on IOT (Internet of Thing) device (eg. smartphone or
notebook program)
 Power up processor unit (WLL6540(RoHS) power source).
 Scan for Wi-Fi network SSID (WLL6540(RoHS) as default SSID), connect to
SSID, and input password. (End-user can change SSID/Password from the
application program)
 Launch application and follow program’s guide to link wireless data
 For detail, please reference end-product’s user’s manual

USA - Federal Communications Commission
(FCC)
FCC Radiation Exposure Statement
Interference Statement
These devices comply with Part 15 of the FCC Rules. Operation of the devices
is subject to the following two conditions: (1) The devices may not cause
harmful interference, and (2) The devices must accept any interference that
might cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If the equipment is not installed and used in accordance
with the instructions, the equipment might cause harmful interference to radio
communications. There is no guarantee, however, that such interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception (which can be determined by
turning the equipment off and on), the user is encouraged to try to correct the
interference by taking one or more of the following measures:
 Relocate this device.
 Increase the separation between the device and the receiver.
 Connect the device into an outlet on a circuit different from that of other
electronics.
 Consult the dealer or an experienced radio technician for help.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.

This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter
or antenna.

As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.

End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: H8N-WLL6540”. The grantee's FCC ID can be used only when
all FCC compliance requirements are met.

Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.

End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains transmitter module IC: 1353A-WLL6540”.
Contient le module d'émission IC: 1353A-WLL6540

This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.

CAN ICES-3 (*)/NMB-3(*)
* Insert either “A” or “B” but not both to identify the applicable Class of ITE.

The Country Code Selection feature is disabled for products marketed in the
US/Canada

Document Created: 2015-11-06 08:54:29
Document Modified: 2015-11-06 08:54:29

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC