Test report 2

FCC ID: H8N-DPR2325

Test Report

Download: PDF
FCCID_459738

FCC ID: H8N-DPR2325 4.4.8 TEST RESULTS (B) DPR2325 SERIES 2.4GHz Wireless Mini EUT MODEL CABLE MODEM PCI Card P/N: XXXXXXX INPUT POWER ENVIRONMENTAL 18 deg. C, 64% RH, 120 Vac, 60 Hz (SYSTEM) CONDITIONS 991 hPa TESTED BY: Ansen Lei CHANNEL PEAK POWER PEAK POWER CHANNEL FREQUENCY OUTPUT LIMIT PASS/FAIL (MHz) (dBm) (dBm) 1 2412 15.04 30 PASS 6 2437 15.08 30 PASS 11 2462 15.00 30 PASS Report No.: RF930202R01C 51 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.5 POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 Aug. 12, 2004 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF930202R01C 52 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.5.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator, the bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3kHz RBW and 30kHz VBW, set sweep time=span/3kHz. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3kHz for a full response of the mixer in the spectrum analyzer. 4.5.4 DEVIATION FROM TEST STANDARD No deviation 4.5.5 TEST SETUP EUT SPECTRUM ANALYZER 4.5.6 EUT OPERATING CONDITIONS Same as 4.3.6 Report No.: RF930202R01C 53 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.5.7 TEST RESULTS (A) DPR2325 SERIES 2.4GHz Wireless Mini EUT MODEL CABLE MODEM PCI Card P/N: XXXXXXX INPUT POWER ENVIRONMENTAL 18 deg. C, 64% RH, 120 Vac, 60 Hz (SYSTEM) CONDITIONS 991 hPa TESTED BY: Ansen Lei CHANNEL RF POWER LEVEL IN MAXIMUM CHANNEL FREQUENCY 3 KHz BW LIMIT PASS/FAIL NUMBER (MHz ) (dBm) (dBm) 1 2412 -11.00 8 PASS 6 2437 -11.66 8 PASS 11 2462 -11.27 8 PASS Report No.: RF930202R01C 54 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH1 Report No.: RF930202R01C 55 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH6 Report No.: RF930202R01C 56 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH11 Report No.: RF930202R01C 57 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.5.8 TEST RESULTS (B) DPR2325 SERIES 2.4GHz Wireless Mini EUT MODEL CABLE MODEM PCI Card P/N: XXXXXXX INPUT POWER ENVIRONMENTAL 18 deg. C, 64% RH, 120 Vac, 60 Hz (SYSTEM) CONDITIONS 991 hPa TESTED BY: Ansen Lei CHANNEL RF POWER LEVEL IN MAXIMUM CHANNEL FREQUENCY 3 KHz BW LIMIT PASS/FAIL NUMBER (MHz ) (dBm) (dBm) 1 2412 -13.34 8 PASS 6 2437 -13.31 8 PASS 11 2462 -14.88 8 PASS Report No.: RF930202R01C 58 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH1 Report No.: RF930202R01C 59 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH6 Report No.: RF930202R01C 60 Issued: August 04, 2004

FCC ID: H8N-DPR2325 CH11 Report No.: RF930202R01C 61 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.6 BAND EDGES MEASUREMENT 4.6.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.6.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 Aug. 12, 2004 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.6.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 1MHz and 1kHz with suitable frequency span including 100MHz bandwidth from band edge. The band edges was measured and recorded. 4.6.4 DEVIATION FROM TEST STANDARD No deviation 4.6.5 EUT OPERATING CONDITION Same as Item 4.3.6. Report No.: RF930202R01C 62 Issued: August 04, 2004

FCC ID: H8N-DPR2325 4.6.6 TEST RESULTS (A) The spectrum plots are attached on the following 4 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). Mode A NOTE: The band edge emission plot on the following 1 ~ 2 pages show 54.17dB delta between carrier maximum power and local maximum emission in restrict band (2.3866GHz). The emission of carrier strength list in the test result of channel 1 at the item 4.2.8 is 103.74dBuV/m, so the maximum field strength in restrict band is 103.74 – 54.17 = 49.57dBuV/m which is under 54 dBuV/m limit. NOTE: The band edge emission plot on the following 3 ~ 4 pages show 49.58dB delta between carrier maximum power and local maximum emission in restrict band (2.4838GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.8 is 102.76dBuV/m, so the maximum field strength in restrict band is 102.76 – 49.58 = 53.18dBuV/m which is under 54 dBuV/m limit. Mode B NOTE: The band edge emission plot on the following 1 ~ 2 pages show 54.17dB delta between carrier maximum power and local maximum emission in restrict band (2.3866GHz). The emission of carrier strength list in the test result of channel 1 at the item 4.2.8 is 103.44dBuV/m, so the maximum field strength in restrict band is 103.44 – 54.17 = 49.27dBuV/m which is under 54 dBuV/m limit. NOTE: The band edge emission plot on the following 3 ~ 4 pages show 49.58dB delta between carrier maximum power and local maximum emission in restrict band (2.4838GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.8 is 100.72dBuV/m, so the maximum field strength in restrict band is 100.72 – 49.58 = 51.14dBuV/m which is under 54 dBuV/m limit. Report No.: RF930202R01C 63 Issued: August 04, 2004

& olowzozoceui on uoday SEECHAC—NBH ‘CI 004 +zBw 1 Mz Marker 1 [T1 ] *vew 1 kiz 2.18 dBm Ref 20.5 dBm +ats 30 ds SWT 250 ms 2.412000000 GHz 20 offset 0.$ ar % Ti |— —s2l01 asm —10 . 400000600 enz |## b i pra | 1[ 1 1 D1 2.18) cBm | sas aedd —o : 9e es pv1 Yie: _ —#1 99 aBm —=0 5 : ;fo 00 onz p2 —17.82 abm i— ——20 1 9 ——30 . |—40 _ |—so I @0 L——70 ~4 +ooz ‘po nBny ipanss| Center 2.368 GHz 10 miz/ Span 100 MHz

OLOMZOZoEeAN on uodex SeSECAdQ—N8H ‘UI 004 *RBW 100 kAz Marker 1 (TI1 ] *VBW 100 kHz —43.87 dBm Ref 20.5 dBm *Att 30 dB SWT 2.25 s 23.650000000 GHz 20 Offset 0. dB —10 D1 3.92) dBm LVL ——10 D2 —16.08 dBm ——20 5o ——30 4 H Wfia&wPE EopatnCoaae0 —— 60 #ooz ‘po isnBny :panss| Start 2.5 GHz 2.25 CHz/ Stop 25 CGHz

olowzozoceui on uoday SEECHAC—NBH ‘CI 004 *RBw 1 MHz Marker 1 [Tl j *veW 1 kHz 2.03 dBm Ref 20.5 dBbm *ratt 30 as sw= 250 ms 2.462000000 esz 20 offket 0.5 as HMazkes] 2 (T1 —48}90 aBm Lo. 21. 483500600 cHz Marker| 3 [Tl ~Aor,2.03) czm —47}55 asm| o + p \ Marker| 4 [Tl j cve \ sol e3 amm ——30 t 21. 500000000 GHz I Jzo DZ\ —17.97 am w w 1 99 30 : | ——410 l |—so g PM\ A |—60 Rarneainaw s _ 200 ——70 +ooz ‘po nBny ipanss| ea Center 2.502 GHz 10 mHe/ span 100 »itz

oloxzozosedx on modex SEEZUAIU—N8H ‘lI 004 *RBW 100 kHz Marker 1 [TI ] *vBW 100 kHz —42.41 dBm *Att Ref 20.5 dem 30 ds SswWT 2.25 s 21.895000000 cHz 20 Offéet 0.5 am yas ts D1 3.22| dBm LVL |——10 D2 —16.78 dbm 19 ——30 ——40 EuS WWWM ht Ariahes ——60 #oor o isn6ny :panss| HH%\/ k\/ Start 2.5 GHz 2.25 GHz/ Ston 25 an>

FCC ID: H8N-DPR2325 4.6.7 TEST RESULTS (B) The spectrum plots are attached on the following 4 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). Mode A NOTE: The band edge emission plot on the following 1 ~ 2 pages show 48.58dB delta between carrier maximum power and local maximum emission in restrict band (2.3900GHz). The emission of carrier strength list in the test result of channel 1 at the item 4.2.9 is 101.08dBuV/m, so the maximum field strength in restrict band is 101.08 – 48.58 = 52.50dBuV/m which is under 54 dBuV/m limit. NOTE: The band edge emission plot on the following 3 ~ 4 pages show 48.63dB delta between carrier maximum power and local maximum emission in restrict band (2.4835GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.9 is 101.92dBuV/m, so the maximum field strength in restrict band is 101.92 – 48.63 = 53.29dBuV/m which is under 54 dBuV/m limit. Mode B NOTE: The band edge emission plot on the following 1 ~ 2 pages show 48.58dB delta between carrier maximum power and local maximum emission in restrict band (2.3900GHz). The emission of carrier strength list in the test result of channel 1 at the item 4.2.9 is 100.20dBuV/m, so the maximum field strength in restrict band is 100.20 – 48.58 = 51.62dBuV/m which is under 54 dBuV/m limit. NOTE: The band edge emission plot on the following 3 ~ 4 pages show 48.63dB delta between carrier maximum power and local maximum emission in restrict band (2.4835GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.9 is 98.03dBuV/m, so the maximum field strength in restrict band is 98.03 – 48.63 = 49.40dBuV/m which is under 54 dBuV/m limit. Report No.: RF930202R01C 68 Issued: August 04, 2004

olowzozoceay ron uodey SZECHACNSH ‘C1 004 @ *RBW 1 MHz Marker 1 [T1 ] & +vew 1 khz 1.62 dBm Ref 20.5 dBm *aAtt 30 dB *swT 200 ms 2.410200000 GHz 20 Offfet 0. an D1 1. 62 dBm D2 —i18.38 dbm =zs 69 |——30 |—40 +ooz ‘vo inBny ‘panss| ——70 Center 2.372 GHz 10 MH2/ Span 100 MHz

OLOMZOZoEeAN on uodex SeSECAdQ—N8H ‘UI 004 *RBW 100 kHz Marker 1 ([T1 1 *VBW 100 kz ~44.17 dBm Ref 20.5 dEm *Att dB *SWT 200 ms 20 Offset 0.% 30 21.985000000 cHz dB Pi——O— cBm LVvL ——10 0Z ——30 WWWW |——60 ——70 #ooz ‘po isnBny :panss| Start 2.5 GHz 2.25 GHz/ Stop 25 GHz

~ olowzozoceui on uoday SEECHAC—NBH ‘CI 004 @ *RBW 1 MHz Marker 1 [T1 j *vew 1 kiz 1.52 dBm Ref= 20.5 aBm *att 30 ds *swT 200 ms 2.464800000 cHz 20 Offket 0.5 oB — — Marker| 2 [Tl —47.01 dBm {——— 2l 483500600 cHz t Marker| 3 [T1 p#1 1.62) arm L — 47}27 d&nm L : —z6: > Marker] 4 2— 500000000 enz aBle— 4 L2 ——30 |—40 |___.. _ \‘S |——50 L_ > hW & |—co ~s 4. . E—70 4 +ooz ‘po nBny ipanss| r2 a Center 2.502 GHz 10 mHz/ Span 100 MHz

oloxzozosedx on modex SEEZUAIU—N8H ‘lI 004 *RBW 100 kHz Marker 1 {Tl ] *VBW 100 kHz —44.12 dBm Ref 20.5 dBm *Att 30 dB *SwWT 200 ms 20.500000000 GHz 20 Offiet 0.5 dB o D1 1.76 dBm LVL ——10 D2 —l18.24 dBm ——20 TL ——30 —40 haskl Nesn ilpne tomrrtin m pet¥veuAlpe fi, ardéwh —— 60 ——70 #oor o isn6ny :panss| HH%\/ k\/ Start 2.5 GHz 2.25 CHz2/ Stop 25 GHZ

FCC ID: H8N-DPR2325 4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION The maximum Gain antenna used in this product is PCB antenna and Dipole antenna with UFL antenna connector. And the maximum Gain of these antennas is 3dBi. Report No.: RF930202R01C 73 Issued: August 04, 2004

FCC ID: H8N-DPR2325 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF930202R01C 74 Issued: August 04, 2004

apr corm

FCC ID: H8N-DPR2325 RADIATED EMISSION TEST Report No.: RF930202R01C 76 Issued: August 04, 2004

y apr corm 930202 ROL

FCC ID: H8N-DPR2325 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP, UL Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, DGT Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Linko RF Lab. Tel: 886-3-3183232 Tel: 886-3-3270910 Fax: 886-3-3185050 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report Format Version 1.1 Report No.: RF930202R01C 78 Issued: August 04, 2004


Document Created: 2004-08-11 16:52:52
Document Modified: 2004-08-11 16:52:52
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC