Rf Exposure Information

FCC ID: H78KPMT2W

RF Exposure Info

Download: PDF
FCCID_2793557

849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: INFO@TIMCOENGR.COM HTTP://WWW.TIMCOENGR.COM RF Exposure Evaluation Report APPLICANT KP ELECTRONIC SYSTEMS LTD. P.O. BOX 42 TEFEN INDUSTRIAL PARK 24959 ISRAEL FCC ID H78KPMT2W MODEL NUMBER MT2W PRODUCT VHF AUTOMATIC METER READING DESCRIPTION TRANSCEIVER W/ 2.4 GHZ TX. STANDARD APPLIED CFR 47 Part 2.1091 PREPARED BY Cory Leverett We, TIMCO ENGINEERING, INC. would like to declare that the device has been evaluated in accordance with 47 CFR Part 2.1091 and meets the requirements. The attached report shall not be reproduced except in full without the written approval of TIMCO ENGINEERING, INC.

GENERAL REMARKS Attestations This equipment has been evaluated in accordance with the standards identified in this report. To the best of my knowledge and belief, these evaluations were performed using the procedures described in this report. I attest that the necessary evaluations were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Authorized Signatory Name: Cory Leverett Engineering Project Manager Date: 9/28/2015 Applicant: KP ELECTRONIC SYSTEMS LTD. FCC ID: H78KPMT2W Report: K\KP H78\2010AUT15\2010AUT15TestReport.docxt Page 2 of 4

RF Exposure Requirements General information Device type: VHF AUTOMATIC METER READING TRANSCEIVER W/ 2.4 GHZ TX. Devices that operate under Part 90 of this chapter are subject to RF exposure evaluation prior to equipment authorization or use. Antenna The manufacturer does not specify an antenna, but a typical antenna has a gain of 0 dBi. Configuration Antenna p/n Type Max. Gain (dBi) Fixed mounted Any omni 0 Operating confiquration and exposure conditions: The conducted output power is shown in the table below. Typical use qualifies for a maximum duty cycle factor of 100%. Nom. Attenuation for RG 213/U: Frequency Attenuation per 100ft. MHz dB 1 .27 10 .55 50 100 200 400 700 900 1000 4000 MPE Calculation: The minimum separation distance is calculated as follows: (30xPxG : E E(V m) = ———— Power dersity. P,(mIW /em ) = d e 3770

The limit for general uncontrolled exposure environment is shown in FCC rule Part 1.11310, Table 1. Minimum Separation Distance for Mobile or Fixed Devices Controlled Exposure Insert values in yellow highlighted boxes to determine Minimum Separation Distance Max Power 2W equals Max Power 2000 mW Duty Cycle 100 % equals Duty Factor 1 numeric Antenna Gain 0 dBi equals Gain numeric 1 numeric Coax Loss 0 dB Gain - Coax Loss 1 numeric 2 Power Density 1 mW/cm Enter power Density from the chart to the right Rule Part 1.1310, Table 1 (A) Frequency 173.5 MHz Freq range Power density Enter this value MHz mW/cm2 mW/cm 2 0.3 - 3 100 100 3 - 30 900/f2 0.0 30-300 1 1 300-1,500 f/300 0.6 1,500-100,000 5 5 f = frequency in MHz Minimum Separation Distance 13 cm 0.13 m Minimum Seperation in Inches 4.963002 Inches Applicant: KP ELECTRONIC SYSTEMS LTD. FCC ID: H78KPMT2W Report: K\KP H78\2010AUT15\2010AUT15TestReport.docx


Document Created: 2019-11-07 22:00:31
Document Modified: 2019-11-07 22:00:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC