Test Report

FCC ID: H5OTR21

Test Report

Download: PDF
FCCID_752044

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 FCC ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT CERTIFICATION TO FCC PART 15 REQUIREMENTS For INTENTIONAL RADIATOR of Car Alarm Transceiver FCC ID Number : H5OTR21 Trade Name : Advance Security Inc. Model Number : TRX970 Agency Series : N/A Report Number : 61208209-RP1 Date : January 10, 2007 Issued to Advance Security Inc. 3F, 48 Ta An Street, Hsi Chih, Taipei Hsien, TAIWAN R.O.C. Issued by Compliance Certification Services Inc. Hsintien Lab. No. 163-1, Chunghsen Road, Hsintien City Taipei Hsien, Taiwan TEL: (02) 2217-0894 FAX: (02) 2217-1029 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Ltd. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 of 24 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE................................................................ 3 2. PRODUCT DESCRIPTION ................................................................................. 4 3. TEST FACILITY.................................................................................................... 4 4. MEASUREMENT STANDARDS........................................................................ 4 5. TEST METHODLOGY......................................................................................... 4 6. MEASUREMENT EQUIPMENT USED............................................................ 5 6.1. TEST INSTRUMENTS..................................................................................... 5 6.2. DESCRIPTION OF SUPPORT UNITS......................................................... 5 7. POWERLINE RFI LIMIT.................................................................................... 5 8. RADIATED EMISSION LIMITS........................................................................ 6 9. SYSTEM TEST CONFIGURATION.................................................................. 6 10. TEST PROCEDURE............................................................................................10 11. EQUIPMENT MODIFICATIONS ....................................................................13 12. TEST RESULT .....................................................................................................14 12.1. MAXIMUM MODULATION PERCENTAGE (M%) ...............................14 12.2. THE EMISSIONS BANDWIDTH .................................................................14 APPENDIX I TEST DATA ........................................................................................15 Page 2 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 1. VERIFICATION OF COMPLIANCE COMPANY NAME : Advance Security Inc. 3F, 48 Ta An Street, Hsi Chih, Taipei Hsien, TAIWAN R.O.C. CONTACT PERSON : Michael Chen / President TELEPHONE NO. : 886-2-8648-1688 EUT DESCRIPTION : Car Alarm Transceiver MODEL NAME/NUMBER : TRX970 FCC ID : H5OTR21 DATE TESTED : December 25, 2006 ~ January 04, 2007 REPORT NUMBER : 61208209-RP1 TYPE OF EQUIPMENT SECURITY EQUIPMENT (INTENTIONAL RADIATOR) EQUIPMENT TYPE 915 MHz Car Alarm Transceiver MEASUREMENT PROCEDURE ANSI 63.4 / 2003 LIMIT TYPE CERTIFICATION FCC RULE CFR 47, PART 15 The above equipment was tested by Compliance Certification Services Inc. for compliance with the requirements set forth in the FCC CFR 47, PART 15. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Warning: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services Inc. will constitute fraud and shall nullify the document. Approved by: Reviewed by: Page 3 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 2. PRODUCT DESCRIPTION Fundamental Frequency 915 MHz Power Source 3.7VDC form battery Transmitting Time Periodic < 5 seconds Associated Transceiver FCC ID: H5OTR19 3. TEST FACILITY The open area test sites and conducted measurement facilities used to collect the radiated data are located at No. 163-1, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 4. MEASUREMENT STANDARDS The site is constructed and calibrated in conformance with the requirements of ANSI C63.4/2003. 5. TEST METHODOLOGY 1. For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 KHz, up to at least the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. (CFR 47 Section 15.33) 2. The test configuration/ mode(s) is as the following: Conduction Mode: 1. CHARGER MODE Radiation Mode(s): TX X MODE (Button 1, 2, 3, 4) 1. TX Y MODE (Button 1, 2, 3, 4) TX Z MODE (Button 1, 2, 3, 4) 2. RX MODE 3. CHARGER MODE Page 4 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 6. MEASUREMENT EQUIPMENT USED 6.1 TEST INSTRUMENTS Open Area Test Site # K Name of Manufacturer Model Serial Number Calibration Due Equipment SITE NSA CCS K Site N/A 09/30/2007 MEASURE SCHAFFNER SCR3501 412 05/18/2007 RECEIVER SPECTRUM No Calibration ADVANTEST R3132 120900029 ANALYZER Required ANTENNA SCHAFFNER CBL 6112B 2846 05/26/2007 PRE- SCHAFFNER CPA9231A 3639 10/10/2007 AMPLIFIER CABLE SUHNER RG 214 N-TYPE #K2 02/17/2007 THERMO- TFA N/A NO.4 02/08/2007 HYGRO METER EMC ANALYZER HP 8566B 2937A06102 07/04/2007 (100Hz-22GHz) ANTENNA EMCO 3115 00022256 01/12/2007 (1-18GHz) AMPLIFIER HP 8449B 3008A01266 02/06/2007 (1-18GHz) CABLE JYEBAO LL142 SMA#RS1 02/06/2007 (1-18GHz) CABLE HUBER SUCOFLEX 104 SMA#RS3 02/06/2007 (1-18GHz) +SUHNER CABLE JYEBAO LL142 SMA#C1 02/06/2007 (1-18GHz) Remark: Each piece of equipment is scheduled for calibration once a year. 6.2 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Peripherals Devices: No. Equipment Model No. Trade Name 1. DC Power Supply PS-140Ya DAIWA 2. Transceiver TRX96 Advance Security Inc. Note: 1) All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2) Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use Page 5 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 .7. POWERLINE RFI LIMIT CONNECTED TO AC POWER LINE SECTION 15.207 CARRIER CURRENT SYSTEM IN THE SECTION 15.205 AND SECTION 15.209, 15.221, FREQUENCY RANGE OF 450 KHz TO 30 MHz 15.223, 15.225 OR 15.227, AS APPROPRIATE. BATTERY POWER NO REQUIRED. 8. RADIATED EMISSION LIMITS GENERAL REQUIREMENTS SECTION 15.209 RESTRICTED BANDS OF OPERATION SECTION 15.205 PERIODIC OPERATION IN THE BAND SECTION 15.231 40.66 -40.70 MHz AND ABOVE 70 MHz. RECEIVER MODE SECTION 15.109 9. SYSTEM TEST CONFIGURATION Use a block of foam and combined it with EUT wrapping rubber band around it. This way it can test X, Y and Z axis. To activate continuous transmitting & receiving, place a small plastic block between rubber band and EUT push button. Radiated Open Site Test Set-up Page 6 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Radiated Open Site Test Set-Up (Receiver Mode) Page 7 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Radiated Open Site Test Set-Up (Charge Mode) Page 8 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 CONDUCTED EMISSION TEST Page 9 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 10. TEST PROCEDURE Radiated Emissions, 15.231(4)(b) Test Set-up for frequency range 30 – 1000 MHz Ground plane Antenna mast 1 - 4 meters 3 meters Turntable Pre-Amp. W/ Test Receiver Fig. 1 1. The EUT was placed on a wooden table on the outdoor ground plane. The search antenna was placed 3-meters from the EUT. 2. The turntable was slowly rotated to locate the direction of maximum emission at each emission falling in the restricted bands of 15.205. The EUT was moved throughout the XY, XZ, and YZ planes to maximize emissions received by the search antenna. 3. Once maximum direction was determined, the search antenna was raised and lowered in both vertical and horizontal polarizations. The maximum readings so obtained are recorded in the data listed below. Page 10 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Test set-up for measurements above 1GHz Ground plane D: 3 Meter D Height: 1-2 meters Turntable Spectrum Analyzer Pre-amp. Horn antenna Fig. 2 1. The EUT was placed on a wooden table on the outdoor ground plane. The search antenna was placed 1-meters from the EUT. The EUT antenna was mounted vertically as per normal installation. 2. The turntable was slowly rotated to locate the direction of maximum emission at each emission falling in the restricted bands of 15.205. The EUT was moved throughout the XY, XZ, and YZ planes to maximize emissions received by the search antenna. 3. Once maximum direction was determined, the search antenna was raised and lowered in both vertical and horizontal polarizations. The maximum readings so obtained are recorded in the data listed below. Page 11 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Conducted Emissions, 15.207 Test Sep-up for frequency range 150 KHz to 30 MHz Vert. reference plane EMI receiver 40cm EUT 80cm LISN Reference ground plane Procedure of Preliminary Test The EUT and Support equipment, if needed, was set up as per the test configuration to simulate typical usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor standing equipment, it is placed on the ground plane, which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. The test equipment EUT installed received AC main power, through a Line Impedance Stabilization Network (LISN), which supplied power source and was grounded to the ground plane. All support equipment power received from a second LISN. The EUT test program was started. Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT. The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes. During the above scans, the emissions were maximized by cable manipulation. The test mode(s) described in Item 3.1 were scanned during the preliminary test. After the preliminary scan, we found the test mode described in Item 3.1 producing the highest emission level. The EUT configuration and cable configuration of the above highest emission levels were recorded for reference of the final test. Page 12 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Procedure of Final Test EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. The test data of the worst-case condition(s) was recorded. 11. Equipment Modifications To achieve compliance to FCC Section 15.231 technical limits, the following change(s) were made during compliance testing: NONE Page 13 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 12. TEST RESULT Powerline RFI Class B Eut Radiated Emission Limits Eut SECTION 15.207 X SECTION 15.209 X SECTION 15.205, 15.209, SECTION 15.205 X 15.221, 15.223, x 15.225 OR 15.227 BATTERY POWER SECTION 15.231 (b) X SECTION 15.231 (e) SECTION 15.109 X 12.1 Maximum Modulation Percentage (M%) CALCULATION: No duty cycle Note: Following is the diagram to show the modulation method of the EUT. This EUT works as a FM modulation. Signal HI will trigger FM OSC to generate a 915.004MHz frequency and signal LOW will trigger FM OSC to generate a 914.996MHz frequency. It is only 0.008MHz deviation, so that there is no duty cycle on it. 12.2 The Emissions Bandwidth The bandwidth of the emissions were investigated per 15.231(c) Center Frequency Measured Limits 345kHz < 915MHz 915X0.5%=4575kHz (refer to plot) Page 14 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 APPENDIX I TEST DATA Page 15 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Test Plot: The Emissions Bandwidth Page 16 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 TEST RESULTS Below 1 GHz Operation Mode: TX Mode / Button#1 Test Date: January 03, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Freq. Pk R dg A v R dg Factor Level Limit M argin Pol (M H z) (dB uV ) (dB uV ) (dB ) (dB uV /m) (dB uV /m) (dB ) (H /V ) 915.01 52.59 52.59 3.20 55.79 81.94 -26.15 3mV _X 915.01 62.00 62.00 3.20 65.20 81.94 -16.74 3mV _Y 915.01 63.45 63.45 3.20 66.65 81.94 -15.29 3mV _Z 915.01 55.02 55.02 3.20 58.22 81.94 -23.72 3mH _X 915.01 59.95 59.95 3.20 63.15 81.94 -18.79 3mH _Y 915.01 51.80 51.80 3.20 55.00 81.94 -26.94 3mH _Z Factor = Antenna F actor + Cable Loss - Pre Am plifier Notes: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak detector mode. 3. Calculation: No duty cycle. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. Page 17 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Operation Mode: TX Mode / Button#2 Test Date: January 03, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Freq. Pk R dg A v R dg Factor Level Limit M argin Pol (M H z) (dB uV ) (dB uV ) (dB ) (dB uV /m) (dB uV /m) (dB ) (H /V ) 915.01 52.69 52.69 3.20 55.89 81.94 -26.05 3mV _X 915.01 59.73 59.73 3.20 62.93 81.94 -19.01 3mV _Y 915.01 71.74 71.74 3.20 74.94 81.94 -7.00 3mV _Z 915.01 56.16 56.16 3.20 59.36 81.94 -22.58 3mH _X 915.01 56.79 56.79 3.20 59.99 81.94 -21.95 3mH _Y 915.01 61.60 61.60 3.20 64.80 81.94 -17.14 3mH _Z Factor = Antenna F actor + Cable Loss - Pre Am plifier Notes: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak detector mode. 3. Calculation: No duty cycle. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. Page 18 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Operation Mode: TX Mode / Button#3 Test Date: January 03, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Freq. Pk R dg A v R dg Factor Level Limit M argin Pol (M H z) (dB uV ) (dB uV ) (dB ) (dB uV /m) (dB uV /m) (dB ) (H /V ) 915.01 64.87 64.87 3.20 68.07 81.94 -13.87 3mV _X 915.01 67.70 67.70 3.20 70.90 81.94 -11.04 3mV _Y 915.01 70.61 70.61 3.20 73.81 81.94 -8.13 3mV _Z 915.01 66.50 66.50 3.20 69.70 81.94 -12.24 3mH _X 915.01 65.81 65.81 3.20 69.01 81.94 -12.93 3mH _Y 915.01 59.16 59.16 3.20 62.36 81.94 -19.58 3mH _Z Factor = Antenna F actor + Cable Loss - Pre Am plifier Notes: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak detector mode. 3. Calculation: No duty cycle. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. Page 19 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Operation Mode: TX Mode / Button#4 Test Date: January 03, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Freq. Pk R dg A v R dg Factor Level Limit M argin Pol (M H z) (dB uV ) (dB uV ) (dB ) (dB uV /m) (dB uV /m) (dB ) (H /V ) 915.01 65.40 65.40 3.20 68.60 81.94 -13.34 3mV _X 915.01 66.44 66.44 3.20 69.64 81.94 -12.30 3mV _Y 915.01 69.82 69.82 3.20 73.02 81.94 -8.92 3mV _Z 915.01 63.53 63.53 3.20 66.73 81.94 -15.21 3mH _X 915.01 68.02 68.02 3.20 71.22 81.94 -10.72 3mH _Y 915.01 56.23 56.23 3.20 59.43 81.94 -22.51 3mH _Z Factor = Antenna F actor + Cable Loss - Pre Am plifier Notes: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak detector mode. 3. Calculation: No duty cycle. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. Page 20 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Operation Mode: RX Mode Test Date: December 25, 2006 o Temperature: 20 C Humidity: 70 % RH Tested by: Mark Hsu Reading Freq Amptd Margin Limit Reading Factor Pol. Type (MHz) (dBuV/m) (dB) (dBuV/m) (dBuV) (dB/m) (H/V) (P/Q/A) 51.2300 22.06 -17.94 40.00 40.50 -18.44 Q V 121.2300 21.03 -22.47 43.50 34.80 -13.77 Q V 163.6900 28.55 -14.95 43.50 42.50 -13.95 Q V 173.7700 26.94 -16.56 43.50 41.40 -14.46 Q V 183.8800 23.19 -20.31 43.50 37.90 -14.71 Q V 242.4800 28.22 -17.78 46.00 39.60 -11.38 Q V 51.4100 21.13 -18.87 40.00 39.60 -18.47 Q H 121.2800 23.03 -20.47 43.50 36.80 -13.77 Q H 163.6800 26.95 -16.55 43.50 40.90 -13.95 Q H 173.7800 25.74 -17.76 43.50 40.20 -14.46 Q H 183.9000 22.79 -20.71 43.50 37.50 -14.71 Q H 242.4700 25.52 -20.48 46.00 36.90 -11.38 Q H Notes: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using Peak detector mode. 3. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 4.The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. 5.Another transmitter trigger signal: Vertical: 915.0050MHz / 73.64dBuV/m 6. Another transmitter trigger signal: Horizontal: 915.0050MHz / 86.15dBuV/m Page 21 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Above 1 GHz Operation Mode: TX Mode / Button#1 Test Date: December 25, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Freq. Pk R dg A v R dg Factor Level Limit M argin Pol (M H z) (dB uV ) (dB uV ) (dB ) (dB uV /m) (dB uV /m) (dB ) (H /V ) 1024.00 48.10 --- -10.35 37.75 74.00 -36.25 3mV 1024.00 --- --- --- -- 54.00 -- 3mV 1078.00 49.60 --- -10.12 39.48 74.00 -34.52 3mV 1078.00 --- --- --- --- 54.00 --- 3mV 1220.50 50.60 --- -9.47 41.13 74.00 -32.87 3mV 1220.50 --- --- --- -- 54.00 -- 3mV 2371.00 46.60 --- -3.55 43.05 74.00 -30.95 3mV 2371.00 --- --- --- --- 54.00 --- 3mV 1430.50 46.60 46.60 -8.51 38.09 61.94 -23.85 3mV 1738.00 46.30 46.30 -3.51 42.79 61.94 -19.15 3mV 1099.00 50.50 --- -10.02 40.48 74.00 -33.52 3mH 1099.00 --- --- --- --- 54.00 --- 3mH 1564.00 47.40 --- -7.77 39.63 74.00 -34.37 3mH 1564.00 --- --- --- --- 54.00 --- 3mH 2219.50 46.50 --- -4.16 42.34 74.00 -31.66 3mH 2219.50 --- --- --- --- 54.00 --- 3mH 1645.00 46.80 46.80 -7.26 39.54 61.94 -22.40 3mH 1831.00 48.00 48.00 -6.09 41.91 61.94 -20.03 3mH 1897.00 46.90 46.90 -5.68 41.22 61.94 -20.72 3mH Factor = A ntenna Factor + Cable Loss - Pre Am plifier Notes: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 3. Radiated emissions measured in frequency above 1000MHz were made with an instrument using Peak detector mode (RBW=VBW=1MHz) of the emission shown in Rdg column. 4. Average detector mode (RBW=1MHz, VBW=10Hz) for restricted frequency bands. 5. Calculation: No duty cycle. 6. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Page 22 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 Operation Mode: RX Mode Test Date: December 25, 2007 Temperature: 20oC Humidity: 70 % RH Tested by: Mark Hsu Peak AV Ant. / CL Actual Fs Peak AV Freq. Ant. Pol Margin Reading Reading CF Peak AV Limit Limit Remark (MHz) H/V (dB) (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- * No Any Emissions Were Found Within 20dB Below Limits From 1 GHz To 5 GHz. Notes: 1. Measuring frequencies from 1 GHz to 5 GHz. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 3. Radiated emissions measured in frequency above 1000MHz were made with an instrument using Peak detector mode and average detector mode of the emission shown in Actual FS column. 4. Spectrum Peak Setting 1GHz - 26GHz, RBW = 1MHz, VBW = 1MHz, Sweep time = Auto. 5. Spectrum AV Setting 1GH z- 26GHz, RBW = 1MHz, VBW = 10Hz, Sweep time = Auto. Page 23 Rev. 00

Compliance Certification Services Inc. Report No.: 61208209-RP1 FCC ID: H5OTR21 Date of Issue: January 10, 2007 TEST RESULTS No non-compliance noted Test Data Operation Mode: Charger Mode Test Date: January 04, 2007 Temperature: 20oC Humidity: 67 % RH Tested by: Mark Hsu M eter Corrected Reading Freq Reading C.F. Reading Limit M argin Type Line M Hz (dBuV) (dB) (dBuV) (dBuV) (dB) (P/Q/A) (L1/L2) 0.327 48.55 0.58 49.13 59.53 -10.40 P L1 0.532 43.19 0.68 43.87 56.00 -12.13 P L1 1.037 45.02 0.70 45.72 56.00 -10.28 P L1 1.269 45.74 0.70 46.44 56.00 -9.56 P L1 1.269 21.95 0.70 22.65 46.00 -23.35 A L1 2.213 49.38 0.72 50.10 56.00 -5.90 P L1 2.213 26.89 0.72 27.61 46.00 -18.39 A L1 3.346 44.00 0.76 44.76 56.00 -11.24 P L1 0.352 46.99 0.16 47.15 58.91 -11.76 P L2 0.909 42.95 0.20 43.15 56.00 -12.85 P L2 1.021 46.30 0.20 46.50 56.00 -9.50 P L2 1.021 30.19 0.20 30.39 46.00 -15.61 A L2 1.236 47.04 0.20 47.24 56.00 -8.76 P L2 1.236 25.71 0.20 25.91 46.00 -20.09 A L2 2.167 49.90 0.23 50.13 56.00 -5.87 P L2 2.167 27.00 0.23 27.23 46.00 -18.77 A L2 3.509 44.52 0.34 44.86 56.00 -11.14 P L2 Remark: 1. The measuring frequencies range between 0.15 MHz and 30 MHz. 2. The emissions measured in the frequency range between 0.15 MHz and 30MHz were made with an instrument using Quasi-peak detector and Average detector. 3. “---” denotes the emission level was or more than 2dB below the Average limit, and no re-check was made. 4. The IF bandwidth of SPA between 0.15MHz and 30MHz was 10kHz. The IF bandwidth of Test Receiver between 0.15MHz and 30MHz was 9kHz. 5. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line) 6. C.F. = Cable Attenuation Factor / SPA = Spectrum analyzer Page 24 Rev. 00


Document Created: 2007-01-25 12:07:03
Document Modified: 2007-01-25 12:07:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC