Users Manual

FCC ID: H5OT69

Users Manual

Download: PDF
FCCID_4047638

Remote Start / Power Harness (6-Pin) PINK IGNITION 1 ( + ) Tach Programming User Selectable LED RED BATTERY 12V ( + ) Replacement Part PINK/WHITE IGNITION 2 ( + ) P # 4120110 ORANGE ACCESSORY 1 ( + ) P RED/WHITE BATTERY 12V ( + ) The unit will not operate unless tach is programmed or a tachless option is This feature will control whether the LED is ON or OFF when the system is Armed/ PURPLE STARTER OUTPUT - MOTOR SIDE ( + ) turned ON. If an attempt is made to start the vehicle via the remote start without first Locked. This will be selectable in feature programming OR on-the-fly without entering programming tach, the unit will flash the parking lights 7 times indicating tach has not the programming feature banks. Notification Harness (4-Pin) been learned and stored. If the tach rate is not properly programmed to the specific Replacement Part WHITE/RED PARKING LIGHT INPUT 1. Turn the ignition ON, OFF, ON, OFF. WHITE PARKING LIGHT OUTPUT P vehicle, the unit may not realize that the vehicle is running in certain instances and #4120145 BLACK GROUND re-engage the starter motor. 2. Press and release the valet/programming button 3 times. The system BROWN SIREN OUTPUT ( + ) will respond with 1 chirp for ON or 2 chirps for OFF. Programming Note: P The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil FLCART HARNESS PORT packs, or single injector. To learn tach: Dome Light Delay / Theater Dimming The default wire function settings are listed next to the wire color. Wires shown with P can be 1. Turn the ignition key to the ON position. programmed to perform different functions. ** RF KITS SOLD SEPERATELY ** Refer to the Feature Programming section to Replacement Parts 2. Press and release the valet/override button 3 times. The system can be programed to delay arming after the lock button is pressed change the default setting. ANTENNA 1-Way # 4180065 3. Immediately turn the ignition key OFF. (60 second max) for vehicles with a dome light delay or theater dimming feature. ANTENNA PORT LED 2-Way # 4180064 Once programed the system will ‘learn’ the timing of the dome light delay and add 2 VALET Harness (4-Pin) # 4120388 4. Press and hold the valet/override button, then start the vehicle using seconds before arming. the key. 1. Close all doors with ignition off. 5. When the unit senses the tach signal, the parking lights will begin to flash. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , E CRS UNLOCK, LOCK. The LED will light solid to indicate the system has CAS SHOCK SENSOR PORT 6. Allow the vehicle to settle to a normal idle speed. entered DOME DELAY LEARN MODE. 7. Release the valet/program push-button switch. The parking lights will BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - ) 3. Immediately OPEN then CLOSE the door WITHOUT disarming the PURPLE/WHITE TACH INPUT turn on for 2 seconds and 1 long chip will indicate that the learned system. The system will then monitor the door trigger wire. Once the GRAY/RED PARKING BRAKE INPUT ( - ) tach signal is stored and the unit has exited tach learn mode. GREEN DOOR TRIGGER INPUT ( - ) dome light turns off, the system will then add 2 seconds and then exit BLUE/WHITE INSTANT TRIGGER INPUT ( - ) NOTE: If the unit fails to learn tach rate due to an improper tach connection or a the learning mode. WHITE/BLUE EXTERNAL START INPUT ( - ) poor tach source, the parking lights will not flash. To correct this situation, locate and PURPLE DOOR TRIGGER INPUT ( + ) 4. The LED will begin to flash indicating the system has exited the BROWN/RED BRAKE INPUT ( + ) connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learning mode and is now armed. GRAY HOOD INPUT ( - ) learn routine. Replacement Part PINK/BLACK AUX 5 OUTPUT ( - ) P GRAY/BLACK AUX 3 OUTPUT ( - ) P Defaulting the Dome Light Delay: Turn the ignition ON then OFF 3 times then #4120389 ORANGE GROUND WHEN ARMED ( - ) P Smart Tachless Mode Replacement Part VIOLET/BLACK AUX 1 OUTPUT ( - ) P press and hold the valet button for 5 seconds, the system will chirp 1 time indicating # 4360698 Input / Output RED/WHITE TRUNK RELEASE OUTPUT ( - ) P the learned delay time has been cleared. Harness (22-Pin) BROWN/BLACK HORN OUTPUT ( - ) Smart Tachless Mode is available only if a tach signal has never been learned to the LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) P LT BLUE FACTORY ARM / PULSE AFTER START ( - ) P system and when activated will automatically change the Tach Mode feature in option GREEN/WHITE PULSE AFTER SHUTDOWN ( - ) P programming to Tachless without the need to enter the feature programming mode. BLACK/YELLOW PULSE DURING CRANK ( - ) P BLUE/GREEN FACTORY DISARM 2 / 2ND UNLOCK ( - ) P ORANGE/BLACK AUX 4 OUTPUT ( - ) P 1. Activate the remote start. The parking lights should begin flashing 7 WHITE/BLACK AUX 2 OUTPUT ( - ) P times indicating no tach signal has been learned. FLCART PORT 2. Within the 7 flash time period, press and hold the button. 3. The system will chirp 1 time indicating the system is now in tachless Door Lock Harness (3-Pin) BLUE UNLOCK ( - ) P mode. OPEN Replacement Part #1031423 GREEN LOCK ( - ) P TELEMATICS PORT Adjusting the Shock Sensor DBI PORT 1. Increase sensitivity by turning the adjustment dial clockwise. PROFESSIONAL FLCART PROGRAMMING PORT 2. Decrease sensitivity by turning the adjustment dial counter clockwise. SERIES STARTER INTERUPT RELAY & HARNESS SHOCK SENSOR & HARNESS Replacement Part #1024405 Replacement Part #4700023 Chirp Delete - User Accessible ORANGE 86 - ARMED OUTPUT ( - ) RED BATTERY 12V ( + ) Security and Remote Start 87 87a RED 85 - IGNITION ( + ) BLACK GROUND WHEN ARMED ( - ) System ARM/DISARM chirps can be toggled ON or OFF without entering the BLACK 87A - STARTER OUTPUT - MOTOR SIDE BLUE FULL TRIGGER ( - ) 86 85 programming feature banks. 30 WHITE / BLACK OPEN 30 - STARTER INPUT - KEY SIDE 87 - OPEN GREEN WARN AWAY TRIGGER ( - ) 1. Turn the ignition ON then OFF. Installation Quick Reference 2. Press and release the valet/programming button 3 times. The system Guide will respond with 1 chirp for ON or 2 chirps for OFF. Remote Start Shutdown Diagnostics Security Trigger Zones caSECRS If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input. If the security system has been triggered the LED will flash one of the patterns below To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button. indicating the zone. PARKING LIGHT FLASHES SHUTDOWN ZONE LED FLASHES TRIGGER ZONE 3 Flashes Hood / Brake Input 2 Flashes Hood / Trunk Input 4 Flashes Remote Start Valet Mode 3 Flashes Door Input 5 Flashes Manual Transmission Mode not ready 4 Flashes Shock Sensor Complete guides also available at 7 Flashes Tach not learned / Crank Average not learned 5 Flashes Ignition Input www.voxxuniversity.com 2017 Vo x x Electronics Corporation. All rights reserved.

Feature Bank 1 - 3 Chirps Transmitter Programming Feature Bank 4 - 6 Chirps Remote Start Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Set Up & Programming 1 RS Confirmation Chirp ON OFF Refer to transmitter programming. Transmitter Programming - Feature Bank 1 2 Run Time 15 Minutes 5 Minutes 10 Minutes 20 Minutes 45 Minutes 60 Minutes 3 Running Lights Steady Flashing 1. Turn the ignition ON. Feature Bank 2 - 4 Chirps 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Security Control 2. Press and hold the valet/override button. 4 Tach Mode Tach Tachless Hybrid DBI Port 1 Silent Choice ON OFF 3. Within 10 seconds the system will chirp (3) three times. 5 Voltage Level High Low 2 Door Locks Active Passive 4. Press 1 button of each transmitter you wish to program. 6 Crank Time 1.0 Seconds 0.8 Seconds 1.5 Seconds 2.0 Seconds 4.0 Seconds 5. The system will respond with 1 chirp for each accepted transmitter. 3 System Arming Active Passive 7 Crank Output 6. Pressing the override button at anytime during programming will advance to Averaging Preset Time 4 System Notifications Siren & Horn Siren Only Horn Only the next bank. 8 Diesel Delay OFF 10 Sec. Delay 15 Sec. Delay 20 Sec. Delay 45 Sec. Delay 5 Alarm Duration 30 Seconds 60 Seconds 9 Remote Start Activation 2x Start 1x Start NOTE: The system will exit transmitter programming after 15 seconds of inactivity. ON w/ OEM 6 Security ON OFF Remote Start Ignition 2 Output NOTE: This system has 1 button programming which programs all channels of the 10 Ignition Accessory Start / Crank Pink / White system. 7 Anti-Hijack Mode OFF ON 11 Auto Start Interval 3 Hour 2 Hour NOTE: The system will hold up to 4 transmitters in memory, programming a 5th 8 Ground While Armed Ground While Ground While transmitter will erase the oldest transmitter in memory. Orange ( - ) Output Armed Disarmed 12 Turbo Timer OFF 1 Minute 3 Minute 5 Minute NOTE: This system has PTN - Programmed Transmitter Notification. Each time the DBI Port Protocol / DBI / ADS / DBI / ADS / 9 Telematic Port Protocol Voxx Telematic Voxx Telematic ADS Telematic ADS Telematic 13 Transmission Mode Automatic Manual ignition is turned ON, the LED will flash the number of transmitters programmed to the Standard: Inverted: system. 14 Temperature Start OFF 14F 5F -4F 10 Arm / Disarm Chirps 2 - Arm 1 - Arm 1 - Disarm 2 - Disarm Accessory Output Transmitter programming for 2 Car Mode *2 way LCD system only: 15 Accessory Ignition Start / Crank Orange 11 LED Indicator ON OFF 1. Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the IGN, ACCY, IGN, ACCY, owners manual for 2 car operation) 16 Pulse Outputs with Unlock OFF GWR - Pulse 12 Auto Re-lock OFF Lock Only Arm & Lock GWR After Shutdown 2. Follow the steps above for transmitter programming. After Lock & 13 Extended Parking Lights OFF After Unlock After Lock Unlock Unlock before Unlock Before Lock After Lock After NOTE: 2 car mode requires an additional security system installed in a second 17 RS Door Lock Control OFF Start, Lock Start Start Shutdown vehicle. Parking Light Relay / Trunk ( - ) After Start 14 Standard Inverted Output Feature Bank 2, Programming Update Notice: Firmware version 3.0 or later. Manual Feature Programming - Feature Bank 2, 3, 4, & 5 Feature #9 has been updated to DBI Port Protocol & Telematic Port Protocol which Feature Bank 5 - 7 Chirps now includes a selection for the telematic port protocol. The new default setting of Alternate Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1. Turn the ignition ON. DBI / ADS Telematic is the correct protocol setting for the ASCL6 CarLink device. Pulse Before 2. Press and hold the valet/override button. Pulse Before Factory Disarm Ground While Pulse During Start / During 1 Start / During Ignition Accessory Lt Green / Black Output Unlock Running Crank Unlock - Uses 3. Within 10 seconds the system will chirp (3) three times. Unlock Timing Pulse After 4. Use the valet/override button to advance through each option bank. For Pulse After 2 Factory Arm Start / During Ground While Ignition Accessory Pulse During Start / During feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4) Lt Blue Output Running Crank Lock - Uses Feature Bank 3 - 5 Chirps Lock Lock Timing four, (5) five, (6) six and (7) seven chirps. 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Output Control Pulse After 5. Use the transmitter button to scroll through the selections in each Pulse After Shutdown Pulse After Ground While Pulse During 1 Lock / Unlock Timing 1 Sec. 3.5 Sec. 1 Sec. Lock, 30 Sec. Lock, 2x Lock, 0.5 Sec. 3 Green / White Output Shutdown Running Ignition Accessory Crank Shutdown 2 feature bank, the system will chirp to match the feature number. 2x Unlock 2x Unlock 1 Sec. Unlock Sec. Delay 6. Press the transmitter button or the vehicle brake pedal to change the Pulse Before Factory Disarm 2 Factory Factory Disarm Factory Disarm Factory Disarm Factory Disarm Pulse During Crank Pulse During Ground While Pulse Before Start / During desired feature. The LED will flash indicating the changed feature. 2 2nd Unlock w/ Unlock 4 Ignition Accessory Start / During Blue / Green Output Disarm 2x 500mS 350mS 500mS Black / Yellow Output Crank Running Unlock - Uses Timing Unlock Unlock Timing 3 Ignition Locks OFF Lock / Unlock Lock Only Unlock Only Defaulting All Features: Pressing the button anytime while in any of the feature This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: banks will default all features and return you to feature bank 2 - 4 chirps. Latched until Latched ON (1) This device may not cause harmful interference, and (2) This device must accept any interference received, 4 Trunk Output Timing 1 Sec. 10 Sec. 20 Sec. IGN ON until Button including interference that may cause undesired operation. Press FCC Radiation Exposure Statement NOTE: The system will remain in feature programming mode as long as the ignition is 5 Horn Output Timing 16mS 10mS 30mS 40mS 50mS This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. on, there is no time limit. To exit programming turn the IGNITION OFF. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. 6 Real Panic ON OFF This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. AUX 1 Latched until Dome Light Defrost Output Defrost Output The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and 7 Violet / Black Output 1 Sec. Latched IGN ON Output Single Pulse Latched 5 Min must not be co-located or operating in conjunction with any other antenna or transmitter. After Start After Start AUX 2 Latched until 10 Sec. 10 Sec. 8 1 Sec. Latched White / Black Output IGN ON w/ Arm w/ Disarm PC Based Feature Programming / Firmware Updates AUX 3 Latched until 10 Sec. 10 Sec. 9 1 Sec. Latched Gray / Black Output IGN ON w/ Arm w/ Disarm When using the NEW Code Alarm Utility App along with a VEPROG Programming tool you may program selectable features or update the firmware of this module. Refer to full installation guide for additional detail. AUX 4 Latched until 10 Sec. 10 Sec. 10 1 Sec. Latched Orange / Black Output IGN ON w/ Arm w/ Disarm 11 AUX 5 1 Sec. Latched Latched until 10 Sec. 10 Sec. 1. To download the Code Alarm Utility App visit the Voxx University website at voxxuniversity.com (registration/login required). Pink / Black Output IGN ON w/ Arm w/ Disarm 2. Select VOXXTECH and locate the utility app under the heading Software Downloads. 3. The Code Alarm Utility App download includes both the CA Utility app and necessary VEPROG drivers. Technical Support (800) 421-3209 or visit 4. Install both items before attempting to update modules. www.voxxuniversity.com


Document Created: 2018-10-24 15:35:18
Document Modified: 2018-10-24 15:35:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC