Users Manual

FCC ID: H5OT61

Users Manual

Download: PDF
FCCID_2739141

TRIGGER THE SYSTEM: (OPTIONAL) If alarm option is installed. When armed, your vehicle is protected as follows: 1. Light impacts will trigger the warn-away signal. A long chirp from siren /horn. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren or horn and parking lights will turn on to alert of an intrusion for 30 seconds. Then the siren or horn will stop and automatically reset and re-arm. If any the sensors or detectors are still active, the alarm system will sound a maximum of three-30 second cycles. ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed. SILENT LOCKING AND UNLOCKING: ARMING / DISARMING: Press the button on the Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature “OFF”. CHANGING THE BATTERY IN YOUR TRANSMITTERS transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard; arm / disarm This system is default setting Car-jacking “OFF”. XT-53: The XT-53 transmitter uses a 3-volt lithium ion batteries (#CR2032) To replace the battery, confirmation will be through the vehicles parking lights only. 1. TRANSMITTER ACTIVATES THE CAR JACKING: you will need to use a small flat blade screwdriver. Locate the small notch on the lower right side of the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case from the SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Pressing the button on the transmitter twice Press and hold + button on the transmitter for 1 second while the vehicle’s ignition is ON. The parking bottom case. It should snap apart after breaking the seal. Before removing the batteries note the within 3 seconds will arm the security system and by-pass the shock sensor. The system will chirp light will turns on for 1.5” seconds to indicate car jacking activated. direction of the positive (+) terminal. Place the new batteries in exactly the same manner, being careful one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is 2. DOOR SWITCH ACTIVATE CAR JACKING: not to bend or damage the contact terminal. Snap the cases back together and then test the transmitter programmed to activate for one arming cycle only. The security system will return to normal operation 1. Turn the ignition switch to “ON” position, the system is armed. to insure it arms and disarms the alarm. during the next arming cycle 2. Once the system is armed, if you are forced from the vehicle, the system will active the carjacking trigger when the door is opened and closed while the ignition is “ON”. PASSIVE LOCKING OR ARMING : Programmable TRIGGER THE CAR JACK MODE: Active arming / disarming is controlling your security system via the remote transmitter. This 3-timer circuits will function as follows: security system is equipped with an optional Passive Arming feature, which allows the security First timer: system to arm 30 seconds after the last door is closed. Operation is as follows. a. 50 seconds after the system has been triggered. The siren or horn will start chirping for 15 seconds. 1. Turn the ignition to the “OFF” position and exit the vehicle. b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the 2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you car-jacking feature. reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing c. If not, it will enter second timer car jacking. again once all vehicle entrances are closed. Second timer: 3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or 65 seconds after the system has beer triggered. The siren or horn starts alarming and the parking light starts horn will chirp [1] time and the parking lights will flash [1] time. flashing. PASSIVE DOOR LOCKING: Programmable Third timer: The vehicle doors will automatically lock after passive arming cycle has been completed. 90 seconds after the system has been triggered a. The siren or horn will still be alarming and the parking light flashing. ACTIVE UN-LOCKING – UNLOCK & DISARM: b. The starter disable will activate to prevent the vehicle from starting. c. It will remain active until the vehicle's battery power exhausted. TRANSMITTER OPERATION 1. Press the button on the transmitter. OVERRIDE THE SYSTEM TO TURN OFF CAR JACKING: 2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch. The siren or horn will Transmitter system is now disarmed. The vehicle doors will unlock when interfaced with the security system. stop and the system will be disarmed System Function Remark Button TAMPER DISARMING: (OPTIONAL). If the alarm is triggered; Upon disarming the system the siren or horn will chirp 4 times and parking lights will flash 3 times. This will indicate that the alarm IGNITION CONTROL DOOR LOCKS. has been triggered while armed. If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the Lock Doors & Arm System vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned TWO STEP DOOR UNLOCK: (OPTIONAL) This feature will independently unlock the driver’s Panic function Press and Hold for 3 seconds “OFF”. door only when disarming the security system. Pushing the button on the transmitter a second Car Locator Under armed mode time within 3 seconds will unlock the entire vehicle. (Optional, Additional installation required). TRUNK RELEASE: Press and hold button on transmitter for three seconds to remote control the trunk AUTOMATIC RE-LOCKING or RE-ARM: If this feature is selected, the security system will release or other electric devices. Arm and Delete The 2 Stage Shock - Sensor Press twice within 3 seconds automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed. CAR LOCATOR : Press the button on the transmitter when the vehicle is in the armed / locked mode to active + Silent Arming / Disarming Ignition in "off" position. car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to easily DISARMING WITHOUT A TRANSMITTER locate your car. Unlock Doors & Disarm System The Override function may be used if the remote transmitter is lost or inoperative. LIMITED LIFETIME WARRANTY PROVISIONS Two Steps Door Unlock & Disarm ( U.S. ,Continental U.S. and Canada Only) - System Press twice within 3 seconds. 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) VARAD International offers an industry-leading lifetime system warranty on the Autopage brand of remote start and security 2. Within 10 seconds push and release the valet switch products which protects users of its products from defects in material and workmanship under normal use and circumstances. This Trunk Release (Channel 3) Press and Hold for 2 seconds The alarm will stop sounding and enter the disarm mode. You can now start and operate the warranty only covers materials both sold and installed by an "Authorized Dealer" of Autopage product vehicle normally. "Authorized Dealer" is defined by VARAD International as a company who qualifies to purchase Autopage products directly from - Passive Arming By-pass While the system Disarmed. VALET MODE: VARAD International, or one of its approved distributors. Thus, products not sold nor installed by an "Authorized Dealer" are not The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand covered by this warranty. This includes, but is not limited to, Autopage products sold on Amazon.com that are not supplied directly Silent Arming / Disarming or 4th ch your transmitter to parking attendants or garage mechanics. When the system is in valet mode, by Amazon or eBay.com. If you would like more information on "Authorized Dealer" locations, please e-mail all alarm functions are bypassed, however, the remote panic feature and remote door locks will Customerservice@Varad.com or visit www.Autopageusa.com. remain operational. Autopage Lifetime System Warranty does NOT cover remote transmitters, or RF kits, as these materials are covered by a separate Switching code For 2nd Car Operation. + Enter Valet Mode: warranty. Autopage remote transmitters are covered by a 1-year warranty, which protects users from defects in material and 1. Turn the ignition to “ON” position. workmanship. 2. Push and hold valet switch for 2 seconds or until the LED turns on. The LED will remain on as VARAD International warrants to the original purchaser that this product shall be free of defects in material and workmanship under ALARM OPERATING CONDITION: (OPTIONAL) normal circumstances for the period of time that the original owner of this product owns the vehicle in which it is first installed; long as the system is in 'valet mode'. Parking Lights Starter except that the remote controller unit, or "brain", for the period of five years from the date of installation to the original owner of this Exit Valet Mode: Function Siren or horn LED Doors Disable product. When purchased or prepaid postal to VARAD International, 5349 Zambrano Street, Commerce,CA, USA within the 1. Return to normal operation, turn ignition 'ON'. 2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting warranty period, and if the product is defective, VARAD International i.e. Autopage will at its own option, repair or replace as such. 1. Arm 1 Chirp 1 Flash Slow flash Locking On To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and each entity participating in the 2. Disarm 2or4 Chirps 2 or 3 Flashes Off or Fast flash Unlocking Off the valet mode. stream of commerce there with. This exclusion includes but is not limited to, the exclusion of any and all warranty of merchantability 3. Trigger Alarming Flashing Slow flash On and/or any and all warranty of fitness for a particular purpose and/or any and all warranty of non-infringement or patents, in the PANIC FUNCTION: United States of America and/or abroad. Neither the manufacturer of any entities connected therewith shall be responsible or liability 4. Panic Alarming Flashing Slow flash Locking On The transmitter can be used as a remote panic switch to manually trigger the alarm in case of for any damages whatsoever, including but not limited to, any consequential damages, incidental damages, damages for loss of time, emergency. loss of earnings, commercial loss, loss of economic opportunity and the like, notwithstanding the above, manufacturer does offer a ACTIVE LOCKING – LOCK & ARMING: limited warranty to replace or repair the control module, or "brain", as described above. 1. Press and hold the button on the transmitter for 3 seconds. The alarm will immediately Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation on how long an implied 1. Press button on transmitter. sound. warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you the specific legal 2. The siren or horn will chirp once and the parking lights will flash once indicating that the system is rights, and you may also have other rights, which vary state to state. 2. To stop the alarm, press and hold the button for 3 seconds on the transmitter, the panic VARAD International i.e. Autopage, is not responsible or liable for any damages whatsoever, including but not limited to, any now armed. The vehicle doors will lock upon arming when interfaced with the security system. mode will be turned off immediately. consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial loss, loss of economic Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door, trunk, 3. If the button is not pressed, the alarm will automatically stop after 30 seconds. opportunity, and the like that may or may not result from the operation of Autopage products. Not with standing the above, VARAD or hood lid ajar. (OPTIONAL) International i.e. Autopage does offer a limited warranty to replace or repair the control module, or "brain", as described above.

355A 355A Transmitter Programming INSTALLATION MANUAL Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. 8 PIN CONNECTOR WIRE HARNESS: “Within 15 seconds”. 2. Push the Valet switch 2 times and hold it on the 2nd push until a long chirp is heard then release the valet switch. You are now in the Transmitter programming mode. 3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the signal has been stored into memory. 4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. ALARM FEATURE “B” PROGRAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 5 times and hold in on the 5th push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘B’ programming mode. 3 Press the transmitter button corresponding to the feature you want to program. One Chirp / LED Press one pulse Four Chirps / Transmitter Two Chirps / LED Three Chirps / LED LED four two pulses three pulses Factory Default pulses Button Setting Pathway Parking light turns Parking light turns * Starter Kill relay optional 1 illumination feature “on” for 30- second “on” for 30- second “off” upon an unlock upon an unlock signal ALARM FEATURE “I” PROGRAMMING: signal & 10-second upon a lock signal. 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. Ignition controlled Without ignition 2 Ignition controlled Ignition controlled 2 Push the Valet switch 3 times and hold in on the 3rd push. When a long chirp is heard, release the door locks & controlled door door locks only door unlocks only valet switch. You are now in the Alarm feature ‘I’ programming mode. unlocks locks & unlocks 3 Press the transmitter button corresponding to the feature you want to program. 3 0.8-second Door 3.5-second Door a. The factory default settings is always [1] LED flash, [1] chirp. Double pulse unlock Comfort feature lock pulses. lock pulse. 4 Depress the transmitter button again to change the feature. Simply keep pressing the transmitter button again until the module advances to your desired setting. 3rd Channel Pulsed 3rd Channel 4 Momentary One Chirp / Three Chirps 5 + Button = Button = 4th Press Four Chirps / LED one pulse Two Chirps / / Channel Aux. Transmitter Silent Arm/Disarm LED four Factory Default LED two pulses LED three Gray Wire = Trunk Gray Wire = Two Button pulses 6 + Setting pulses (Channel 3) Output Step Door Unlock Passive Output 1 Passive arming arming with without passive Horn chirp Duration Horn chirp Duration Horn chirp Duration Horn chirp Active arming passive door 7. + door locking duration locking. 5 PIN WIRE HARNESS Standard 50 mS 30 mS 2 Automatic Rearm 10 mS Automatic Rearm off on Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit. 1. Red / White Wire: Parking Light Relay input 45 seconds delay SHOCK SENSOR ADJUSTMENT 3 Instant Door Ajar Door Ajar error 1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. error chirp 2. Push the Valet switch 7 times holding in on the 7th push. Three chirps with a long chirp will be heard. Release the valet 2. White Wire: Parking Light Relay Output chirp. switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode. Horn All 4 Siren Confirmation All Confirmation 3. Press and hold button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the 3. Black Wire: Ground to Vehicle FRAME Confirmation Confirmation chirp on only chirps On shock sensor. chirp on only chirps off White = 4. Press button on the transmitter once. This will decrease sensitivity level by one. Each time the button is pushed and a 5 + White wire= White wire= decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn away & 4. Brown Wire: Positive output To full trigger will be deleted when minimum sensitivity is selected 15A Fuse 4th Channel Siren 4th channel 5. Press button on the transmitter once. This will increase sensitivity level by one. Each time an increase is made the Dome Light Output Momentary Latched siren/horn chirp will respond with [1] chirp. Two chirps indicate the maximum sensitivity. 6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor. 5. Red Wire: +12V To Constant Battery Source Lock/Arm & Lock/Arm a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp. 6 + Unlock/Disarm Confirmation b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp. Confirmation Chirps Chirp Only 7. When you are satisfied with the setting, press the button to lock in the adjustment. One long siren chirp will indicate the ALARM with Keyless Entry unit has locked in the adjustment. This manual was written September 1, 2015 7. + Keyless Entry ONLY Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps, the unit will exit the program mode and return to the disarmed mode. Three long chirps will confirm exit. ©2015 Varad International, Inc. All rights reserved. 8. + Car Jacking Car Jacking GI-S346 feature Off feature On Varad International, Inc. 5349 Zambrano Street, Commerce,CA 90040 www.varad.com

FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.


Document Created: 2015-09-08 13:34:14
Document Modified: 2015-09-08 13:34:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC