Test report

FCC ID: H5OT51

Test Report

Download: PDF
FCCID_1480894

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Car Alarm Transmitter Model: TX731A Brand Name: Advance Security Inc. Issued to Advance Security Inc. 3F, 48 Ta An Street, Hsi Chih, Taipei Hsien, TAIWAN R.O.C. Issued by Compliance Certification Services Inc. Sindian Lab. No.163-1, Jhongsheng Rd, Sindian City, Taipei County 23151, Taiwan (R.O.C.) TEL: (02) 2217-0894 FAX: (02) 2217-1029 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 27 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION............................................................................................. 3 2. EUT DESCRIPTION .................................................................................................................... 4 3. TEST METHODOLOGY ............................................................................................................. 5 3.1 EUT CONFIGURATION .............................................................................................................. 5 3.2 EUT EXERCISE ......................................................................................................................... 5 3.3 GENERAL TEST PROCEDURES .................................................................................................. 5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ............................................. 6 3.5 DESCRIPTION OF TEST MODES ................................................................................................. 6 4. INSTRUMENT CALIBRATION................................................................................................. 7 4.1 MEASURING INSTRUMENT CALIBRATION ........................................................................... 7 4.2 MEASUREMENT EQUIPMENT USED .............................................................................. 7 5. FACILITIES AND ACCREDITATIONS ................................................................................... 8 5.1 FACILITIES .............................................................................................................................. 8 5.2 EQUIPMENT ............................................................................................................................. 8 5.3 TABLE OF ACCREDITATIONS AND LISTINGS ............................................................................ 9 6. SETUP OF EQUIPMENT UNDER TEST .................................................................................. 9 6.1 SETUP CONFIGURATION OF EUT .............................................................................................. 9 6.2 SUPPORT EQUIPMENT .............................................................................................................. 9 7. FCC PART 15.231 REQUIREMENTS...................................................................................... 10 7.1 20DB BANDWIDTH ........................................................................................................... 10 7.2 LIMIT OF TRANSMISSION TIME .............................................................................................. 12 7.3 DUTY CYCLE CORRECTION FACTOR.......................................................................... 14 7.4 RADIATED EMISSIONS ........................................................................................................... 17 7.5 POWERLINE CONDUCTED EMISSIONS .................................................................................... 24 APPENDIX I PHOTOGRAPHS OF TEST SETUP ....................................................................... 25 Page 2 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 1. TEST RESULT CERTIFICATION Applicant: Advance Security Inc. 3F, 48 Ta An Street, Hsi Chih, Taipei Hsien, TAIWAN R.O.C. Equipment Under Test: Car Alarm Transmitter Brand Name: Advance Security Inc. Model: TX731A Date of Test: June 4, 2011 & June 7, 2011 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. Sindian BU. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.207, 15.209 and Part 15.231. The test results of this report relate only to the tested sample identified in this report. Page 3 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 2. EUT DESCRIPTION Product Car Alarm Transmitter Brand Name Advance Security Inc. Model Number TX731A Modulation Technique ASK Power Supply 6VDC Battery Frequency Range 433.92 MHz Antenna Specification Helical Antenna / Gain: -2.5dbi Associated Receiver H5OTR45 Remark: 1. The sample selected for test was production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: H5OT51 filing to comply with Section 15.207, 15.209 and 15.231 of the FCC Part 15, Subpart C Rules. Page 4 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 (2009) and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.231. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4. Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. Page 5 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 (2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: TX731A) had been tested under engineering test mode condition and the EUT staying in continuous transmitting mode. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down position (Y axis) and the worst case was recorded. Page 6 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year. Open Area Test Site Chamber #D Name of Equipment Manufacturer Model Serial Number Calibration Due MEASURE RECEIVER SCHAFFNER SCR3501 342 06/28/2011 ANTENNA SUNOL JB1 A022310 10/04/2011 (30-1000MHz) PRE- EMCI EMC330 980022 01/20/2012 AMPLIFIER CABLE HUBER SUCOFLEX 102 33105/2 01/20/2012 (30-1000MHz) +SUHNER CABLE EMCI EMCI-C-14 CH-D#13 01/20/2012 (30-1000MHz) ATTENUATOR MCL BW-S6W5 CH-D#14 01/20/2012 LOOP ANTENNA EMCO 6502 8905-2356 06/10/2013 SPECTRUM ANALYZER R&S FSP 30 100112 12/07/2011 (9kHz-30GHz) SPECTRUM ANALYZER Agilent E4446A MY48250064 12/29/2011 (9kHz-40GHz) ANTENNA EMCO 3115 00022256 01/09/2012 (1-18GHz) AMPLIFIER HP 8449B 3008A01266 12/19/2011 (1-18GHz) CABLE HUBER SUCOFLEX 102 33106/2 12/19/2011 (1-40GHz) +SUHNER CABLE HUBER SUCOFLEX 102 33633/2 12/19/2011 (18-40GHz) +SUHNER CABLE HUBER SUCOFLEX 104PEA 33959/4PEA 12/19/2011 (1-26.5GHz) +SUHNER CABLE HUBER SUCOFLEX 104PEA 33960/4PEA 12/19/2011 (1-26.5GHz) +SUHNER THERMO- TECPEL DTM-303 NO.3 11/18/2011 HYGRO METER Test S/W EZ-EMC Page 7 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 4.3 MEASUREMENT UNCERTAINTY PARAMETER UNCERTAINTY 3M Semi Anechoic Chamber / 30M~1000M ± 3.98 3M Semi Anechoic Chamber / 1G~18G ± 1.99 3M Semi Anechoic Chamber / 18G~26G ± 2.65 3M Semi Anechoic Chamber / 26G~40G ± 2.97 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.163-1, Jhongsheng Rd, Sindian City, Taipei County 23151, Taiwan (R.O.C.) Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Luchu Hsiang, Taoyuan Hsien 338, Taiwan Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR 16-1-1, CISPR 16-1-2, CISPR 16-1-3, CISPR 16-1-4 and CISPR 16-1-5. Page 8 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo 3M Semi Anechoic Chamber (FCC MRA: TW1039) to perform USA FCC FCC Part 15 measurements 250366 LP0002, RTTE01, FCC Method-47 CFR Part 15 Subpart C, D, E, RSS-210, RSS-310 IDA TS SRD, AS/NZS 4268, AS/NZS 4771, TS 12.1 & 12,2, ETSI EN 300 440-1, ETSI EN 300 440-2, ETSI EN 300 328, ETSI EN 300 220-1, ETSI EN 300 220-2, ETSI EN 301 893, ETSI EN 301 489-1/3/7/17 Taiwan TAF FCC OET Bulletin 65 + Supplement C, EN 50360, EN 50361, EN 50371, RSS 102, EN 50383, EN 50385, EN 50392, IEC 62209, CNS 14958-1, CNS 14959 FCC Method –47 CFR Part 15 Subpart B IEC / EN 61000-3-2, IEC / EN 61000-3-3, IEC / EN 61000-4-2/3/4/5/6/8/11 Canada Industry Canada 3M Semi Anechoic Chamber (IC 2324G-1 / IC 2324G-2) to perform IC 2324D-1 * No part of this report may be used to claim or imply product endorsement by A2LA any agency of the US Government. 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Device Type Brand Model Series No. FCC ID Data Cable Power Cord Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 9 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 7. FCC PART 15.231 REQUIREMENTS 7.1 20DB BANDWIDTH LIMIT The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. Test Configuration Spectrum EUT Analyzer TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The spectrum analyzer center frequency is set to the transmitter frequency. The RBW is set to 10 kHz and VBW is set 30kHz. TEST RESULTS No non-compliance noted. Test Data Frequency 20 dB Bandwidth Limit Result (MHz) (kHz) (MHz) 433.92 63.50 1.0848 PASS Page 10 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Test Plot Page 11 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 7.2 LIMIT OF TRANSMISSION TIME LIMIT According to 15.231 (a)(1), a manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. Test Configuration Spectrum EUT Analyzer TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The spectrum analyzer center frequency is set to the transmitter frequency. The RBW and VBW are set to 100kHz. TEST RESULTS No non-compliance noted Test Data Transmission Frequency Limit time Result (MHz) (Second) (Second) 433.92 2.00 5.00 PASS Page 12 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Test Plot Page 13 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 7.3 DUTY CYCLE CORRECTION FACTOR LIMIT Nil (No dedicated limit specified in the Rules) Test Configuration Spectrum EUT Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set center frequency of spectrum analyzer = operating frequency. 4. Set the spectrum analyzer as RBW, VBW=100KHz, Span = 0Hz, Adjust Sweep = 100ms. 5. Repeat above procedures until all frequency measured were complete. TEST RESULTS No non-compliance noted Test Data Tp = 68.00ms Ton = (0.82*2)+(0.24*45) = 12.44 Duty Cycle Correction Factor= 20* log (Ton / Tp) = 20* log (12.44/68.00) = -14.753 dB Page 14 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Test Plot Tp Channel Number Page 15 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Ton 1 Ton 2 Page 16 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 7.4 RADIATED EMISSIONS LIMIT 1. According to §15.231(b), in addition to the provisions of Section 15.205, the field strength of emissions from intentional radiators operated under this Section shall not exceed the following: Field Strength of Field Strength of Spurious Fundamental Frequency Fundamental Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 – 40.70 2250 225 70 – 130 1250 125 130 – 174 1250 to 3750 ** 125 to 375 ** 174 – 260 3750 375 260 – 470 3750 to 12500 ** 375 to 1250 ** Above 470 12500 1250 Remark: ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, uV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, uV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (mV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (µV/m at 3-meter) (dBµV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 17 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Test Configuration 9kHz ~ 30MHz 3m Loop antenna EUT Spectrum / Receiver Turntable 1m 0.8m Reference ground plane Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Page 18 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 19 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 TEST RESULTS No non-compliance noted Below 1 GHz Operation Mode: TX Mode / Button#1 Test Date: June 4, 2011 Temperature: 26oC Humidity: 60% RH Tested by: Howard Pang Polarity: Ver. / Hor. Freq. Pk R dg A v R dg Factor Level L imit M argin Pol (M H z) (dB uV) (dB uV) (dB ) (dB uV/m) (dB uV/m) (dB ) (H /V) 434.49 55.63 40.84 -8.09 32.75 80.84 -48.10 V _X 868.08 38.52 23.73 -1.56 22.17 60.83 -38.66 V _X 434.49 54.28 39.49 -8.09 31.40 80.84 -49.45 V _Y 868.08 38.53 23.74 -1.56 22.18 60.83 -38.65 V _Y 434.49 53.90 39.11 -8.09 31.02 80.84 -49.83 V _Z 869.05 39.29 24.50 -1.55 22.95 60.83 -37.88 V _Z 434.49 52.63 37.84 -8.09 29.75 80.84 -51.10 H _X 868.08 40.96 26.17 -1.56 24.61 60.83 -36.22 H _X 434.49 52.47 37.68 -8.09 29.59 80.84 -51.26 H _Y 869.05 39.55 24.76 -1.55 23.21 60.83 -37.62 H _Y 434.49 53.19 38.40 -8.09 30.31 80.84 -50.54 H _Z 868.08 39.05 24.26 -1.56 22.70 60.83 -38.13 H _Z Factor = Antenna Factor + C able Loss - Pre Am plifier Av Rdg = Pk Rdg-14.753dB Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz) 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3. Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Level (dBuV/m) – Limit (dBuV/m). Page 20 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Operation Mode: TX Mode / Button#2 Test Date: June 4, 2011 Temperature: 26oC Humidity: 60% RH Tested by: Howard Pang Polarity: Ver. / Hor. Freq. Pk Rdg A v R dg F a c to r L evel L im it M a r g in P ol (M H z ) (d B u V ) (d B u V ) (d B ) (d B u V /m ) (d B u V /m ) (d B ) (H /V ) 4 3 4 .4 9 5 0 .3 1 3 5 .5 2 -8 .0 9 2 7 .4 3 8 0 .8 4 -5 3 .4 2 V _X 8 6 8 .0 8 3 7 .7 9 2 3 .0 0 -1 .5 6 2 1 .4 4 6 0 .8 3 -3 9 .3 9 V _X 4 3 4 .4 9 5 1 .2 5 3 6 .4 6 -8 .0 9 2 8 .3 7 8 0 .8 4 -5 2 .4 8 V _Y 8 6 9 .0 5 3 8 .6 9 2 3 .9 0 -1 .5 5 2 2 .3 5 6 0 .8 3 -3 8 .4 8 V _Y 4 3 4 .4 9 5 0 .6 0 3 5 .8 1 -8 .0 9 2 7 .7 2 8 0 .8 4 -5 3 .1 3 V _Z 8 6 9 .0 5 3 9 .1 5 2 4 .3 6 -1 .5 5 2 2 .8 1 6 0 .8 3 -3 8 .0 2 V _Z 4 3 4 .4 9 5 2 .5 6 3 7 .7 7 -8 .0 9 2 9 .6 8 8 0 .8 4 -5 1 .1 7 H _X 8 6 8 .0 8 3 9 .5 0 2 4 .7 1 -1 .5 6 2 3 .1 5 6 0 .8 3 -3 7 .6 8 H _X 4 3 4 .4 9 5 2 .7 2 3 7 .9 3 -8 .0 9 2 9 .8 4 8 0 .8 4 -5 1 .0 1 H _Y 8 6 8 .0 8 3 9 .6 9 2 4 .9 0 -1 .5 6 2 3 .3 4 6 0 .8 3 -3 7 .4 9 H _Y 4 3 4 .4 9 5 2 .1 2 3 7 .3 3 -8 .0 9 2 9 .2 4 8 0 .8 4 -5 1 .6 1 H _Z 8 6 8 .0 8 3 8 .4 6 2 3 .6 7 -1 .5 6 2 2 .1 1 6 0 .8 3 -3 8 .7 2 H _Z F a c to r = A n te n n a F a c to r + C a b le L o ss - P re A m p lifie r A v R d g = P k R d g -1 4 .7 5 3 d B Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz) 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3. Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Level (dBuV/m) – Limit (dBuV/m). Page 21 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Operation Mode: TX Mode / Button#3 / WORST Test Date: June 4, 2011 Temperature: 26oC Humidity: 60% RH Tested by: Howard Pang Polarity: Ver. / Hor. Freq. Pk Rdg Av R dg Factor L evel L imit M argin Pol (M H z) (dB uV ) (dB uV) (dB ) (dB uV/m) (dB uV /m) (dB ) (H /V) 434.49 51.63 36.84 -8.09 28.75 80.84 -52.10 V _X 869.05 37.80 23.01 -1.55 21.46 60.83 -39.37 V _X 434.49 50.81 36.02 -8.09 27.93 80.84 -52.92 V _Y 869.05 37.40 22.61 -1.55 21.06 60.83 -39.77 V _Y 434.49 49.98 35.19 -8.09 27.10 80.84 -53.75 V _Z 868.08 37.14 22.35 -1.56 20.79 60.83 -40.04 V _Z 434.49 52.28 37.49 -8.09 29.40 80.84 -51.45 H _X 869.05 37.74 22.95 -1.55 21.40 60.83 -39.43 H _X 434.49 54.76 39.97 -8.09 31.88 80.84 -48.97 H _Y 868.08 38.61 23.82 -1.56 22.26 60.83 -38.57 H _Y 434.49 54.93 40.14 -8.09 32.05 80.84 -48.80 H _Z 868.08 38.34 23.55 -1.56 21.99 60.83 -38.84 H _Z Factor = Antenna Factor + Cable Loss - Pre Am plifier Av Rdg = Pk Rdg-14.753dB Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz) 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3. Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Level (dBuV/m) – Limit (dBuV/m). Page 22 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 Above 1 GHz Operation Mode: TX / Button#3 Test Date: June 7, 2011 Temperature: 26oC Tested by: 60% RH Humidity: Howard Pang Polarity: Ver. / Hor. F req. Pk R dg A v R dg F a c to r L evel L im it M a r g in P ol (M H z ) (d B u V ) (d B u V ) (d B ) (d B u V /m ) (d B u V /m ) (d B ) (H /V ) 1 3 0 2 .0 0 3 4 .1 0 --- -8 .7 0 2 5 .3 6 7 4 .0 0 -4 8 .6 4 V 1 3 0 2 .0 0 --- --- --- --- 5 4 .0 0 --- V 1 7 3 6 .0 0 3 5 .9 0 2 1 .1 1 -6 .2 0 1 4 .8 9 6 0 .8 3 -4 5 .9 5 V 2 1 7 0 .0 0 3 2 .4 0 1 7 .6 1 -4 .0 0 1 3 .6 2 6 0 .8 0 -4 7 .1 9 V 1 3 0 2 .0 0 3 4 .0 0 --- -8 .7 0 2 5 .2 6 7 4 .0 0 -4 8 .7 4 H 1 3 0 2 .0 0 --- --- --- --- 5 4 .0 0 --- H 1 7 3 6 .0 0 3 6 .2 0 2 1 .4 1 -6 .2 0 1 5 .1 9 6 0 .8 0 -4 5 .6 2 H 2 1 7 0 .0 0 3 1 .8 0 1 7 .0 1 -4 .0 0 1 3 .0 2 6 0 .8 0 -4 7 .7 9 H F a c to r = A n te n n a F a c to r + C a b le L o ss - P r e A m p lifie r Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Level (dBuV/m) – Limit (dBuV/m). Page 23 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 7.5 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range Limits (dBµV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 * Decreases with the logarithm of the frequency. Test Configuration See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. Test Procedure Not applicable (Since the EUT is powered by battery) TEST RESULTS Not applicable (Since the EUT is powered by battery) Page 24 Rev. 00

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 APPENDIX I-PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION SET UP PHOTOS TX Mode X axis Y axis Page 25 Rev. 00

ne 9, 2011

Compliance Certification Services Inc. Report No.: T110330201-RP1 FCC ID: H5OT51 Date of Issue: June 9, 2011 RADIATED EMISSION SET UP PHOTOS Page 27 Rev. 00


Document Created: 2011-06-09 16:38:38
Document Modified: 2011-06-09 16:38:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC