DFS report

FCC ID: H4ISMPJA

Test Report

Download: PDF
FCCID_2023545

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 FCC DFS Test Report FCC ID : H4ISMPJA Equipment : MHL wireless adapter Model No. : 2A6G / MWA2 Brand Name : Liteon / Acer Applicant : LITE-ON TECHNOLOGY CORP. Address : 18F, 392 RUEY KUANG RD NEIHU TAIPEI, 114 TAIWAN Standard : 47 CFR FCC Part 15.407 Received Date : May 14, 2013 Tested Date : Jul 04 ~ 05, 2013 Operating Mode : Client without radar detection We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: FZ351401 Page : 1 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information.............................................................................................................................................. 5 1.2 Support Equipment List .......................................................................................................................... 5 1.3 The Equipment List ................................................................................................................................ 6 1.4 Testing Condition ................................................................................................................................... 6 1.5 Test Standards ....................................................................................................................................... 6 2 TECHNICAL REQUIREMENTS FOR DFS ............................................................................................ 7 2.1 Applicability of DFS Requirements ......................................................................................................... 7 2.2 DFS Detection Thresholds and Response Requirement ....................................................................... 8 2.3 Radar Test Waveforms .......................................................................................................................... 9 3 TEST RESULT .....................................................................................................................................12 3.1 Channel Closing Transmission and Channel Move Time ....................................................................12 3.2 Non-Occupancy ....................................................................................................................................14 Report No.: FZ351401 Page : 2 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 Release Record Report No. Version Description Issued Date FZ351401 Rev. 01 Initial issue Jul 10, 2013 Report No.: FZ351401 Page : 3 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 Summary of Test Results FCC Rules Description of Test Result 15.407 Channel Closing Transmission Time Pass 15.407 Channel Move Time Pass 15.407 Non-occupancy Pass Report No.: FZ351401 Page : 4 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) Frequency Range (GHz) 5.15~5.25, 5.25~5.35, 5.47~5.725,5.725~5.85 Wireless Function 11a / n HT20 / n HT40 Operating Mode at DFS Band Client without radar detection and ad hoc function Firmware / Software Version Sdk10071.Case10072.Scripts9979 1.1.2 Antenna Details Operating Frequency Band (MHz) / Gain (dBi) Ant. No. Type 5150~5250 5250~5350 5470~5725 1 PCB Antenna 4.2 2 PCB Antenna 3.6 1.2 Support Equipment List Support Equipment List No. Equipment Brand Name Model Name FCC ID 1 AP (Master) D-Link DIR-826L KA2IR826LMO1 2 Notebook DELL LATITUDE-E5420 B6FV9T1 Report No.: FZ351401 Page : 5 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 1.3 The Equipment List Test Site (DF01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer R&S FSV 7 101607 Dec. 19, 2012 Dec. 18, 2013 Horn Antenna ETS-LINDGREN 3115 00149268 Oct. 05, 2012 Oct. 04, 2013 1G-18G RF Cable HUBER+SUHNER SUCOFLEX_104 MY15686/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 296081/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 500199/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 500202/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 296088/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 329023/4 Dec. 24, 2012 Dec. 23, 2013 RF Cable HUBER+SUHNER SUCOFLEX_104 329021/4 Dec. 24, 2012 Dec. 23, 2013 Vector signal R&S SMJ100A 100498 Dec. 13, 2012 Dec. 12, 2013 generator Note: Calibration Interval of instruments listed above is one year. 1.4 Testing Condition Test Item Test Site Ambient Condition Tested By DFS DF01-WS 26°C / 68% Alex Huang 1.5 Test Standards According to the specification of EUT, the EUT must comply with following standards and KDB documents. 47 CFR FCC Part 15.407 FCC 06-96 A1 Report No.: FZ351401 Page : 6 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 2 Technical Requirements for DFS 2.1 Applicability of DFS Requirements 2.1.1 Applicability of DFS Requirements Prior to use of a Channel Operational Mode Requirement Client Without Client With Radar Master Radar Detection Detection Non-Occupancy Period Yes Not required Yes DFS Detection Threshold Yes Not required Yes Channel Availability Check Time Yes Not required Not required Uniform Spreading Yes Not required Not required U-NII Detection Bandwidth Yes Not required Yes 2.1.2 Applicability of DFS Requirements during Normal Operation Operational Mode Requirement Client Without Client With Radar Master Radar Detection Detection DFS Detection Threshold Yes Not required Yes Channel Closing Transmission Time Yes Yes Yes Channel Move Time Yes Yes Yes U-NII Detection Bandwidth Yes Not required Yes Report No.: FZ351401 Page : 7 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 2.2 DFS Detection Thresholds and Response Requirement Below table provides the DFS Detection Thresholds for Master Devices as well as Client Devices incorporating In-Service Monitoring. DFS Detection Thresholds for Master Devices and Client Devices With Radar Detection. Maximum Transmit Power Value (See Notes 1 and 2) ≥ 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note: 1) This is the level at the input of the receiver assuming a 0 dBi receive antenna. 2) Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. DFS Response Requirement Values Parameter Value Non-occupancy period Minimum 30 minutes. Channel Availability Check Time 60 seconds. Channel Move Time 10 seconds. (See Note 1.) Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. (See Notes 1 and 2.) U-NII Detection Bandwidth Minimum 80% of the U- NII 99% transmission power bandwidth. (See Note 3.) Note: 1) The instant that the Channel Move Time and the Channel Closing Transmission Time begins is as follows: • For the Short Pulse Radar Test Signals this instant is the end of the Burst. • For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst generated. • For the Long Pulse Radar Test Signal this instant is the end of the 12 second period defining the Radar Waveform. 2) The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. 3) During the U-NII Detection Bandwidth detection test, radar type 1 is used and for each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. Report No.: FZ351401 Page : 8 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 2.3 Radar Test Waveforms This section provides the parameters for required test waveforms, minimum percentage of successful detections, and the minimum number of trials that must be used for determining DFS conformance. Step intervals of 0.1 microsecond for Pulse Width, 1 microsecond for PRI, 1 MHz for chirp width and 1 for the number of pulses will be utilized for the random determination of specific test waveforms. 2.3.1 Short Pulse Radar Test Waveforms Minimum Radar Pulse Width Number of Percentage of Minimum PRI (µsec) Type (µsec) Pulses Successful Number of Trials Detection 1 1 1428 18 60% 30 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 A minimum of 30 unique waveforms are required for each of the Short Pulse Radar Types 2 through 4. For Short Pulse Radar Type 1, the same waveform is used a minimum of 30 times. If more than 30 waveforms are used for Short Pulse Radar Types 2 through 4, then each additional waveform must also be unique and not repeated from the previous waveforms. The aggregate is the average of the percentage of successful detections of Short Pulse Radar Types 1-4. 2.3.2 Long Pulse Radar Test Waveform Minimum Pulse Number of Percentage Minimum Radar Chirp Width Number of Width PRI (µsec) Pulses per of Number of Type (MHz) Bursts (µsec) Burst Successful Trials Detection 5 50-100 5-20 1000-2000 1-3 8-20 80% 30 The parameters for this waveform are randomly chosen. Thirty unique waveforms are required for the Long Pulse Radar Type waveforms. If more than 30 waveforms are used for the Long Pulse Radar Type waveforms, then each additional waveform must also be unique and not repeated from the previous waveforms. Report No.: FZ351401 Page : 9 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 2.3.3 Frequency Hopping Radar Test Waveform Minimum Hopping Pulse Percentage Minimum Radar Pulses per Hopping Sequence Width PRI (µsec) of Number of Type Hop Rate (kHz) Length (µsec) Successful Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 For the Frequency Hopping Radar Type, the same Burst parameters are used for each waveform. The hopping sequence is different for each waveform and a 100-length segment is selected from the hopping sequence defined by the following algorithm 2.3.4 Radar waveform generation A single R&S SMJ100A Vector Signal Generator is used for the DFS signal generation. This instrument is capable of generating all the above waveforms with Pulse Sequencer Software. The R&S Pulse Sequencer Software comes as a stand-alone PC based software with preconfigured project files for DFS. It simplifies the generation of all required waveforms and offers a one box solution Report No.: FZ351401 Page : 10 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 2.3.5 Verify DFS Detection Threshold levels Master DFS Threshold Level DFS Threshold level: -63 dBm at the antenna connector(-63 dBmconducted) in front of the antenna(-63 dBm e.i.r.p.) The Interference Radar Detection Threshold Level is (-64dBm) + (0 [dBi] ) + {1 dB}= -63 dBm. That had been taken into account the master output power range and antenna gain. Without Data Traffic Plot (Noise Plot) Master Data Traffic Plot Client(EUT) Data Traffic Plot CalibrationRadar #1 detection threshold level Report No.: FZ351401 Page : 11 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 3 Test Result 3.1 Channel Closing Transmission and Channel Move Time Channel Closing Transmission Time Channel Move Time Modulation Freq. Radar Mode (MHz) Type Test Limit Test Limit Test Limit (0-200ms) (0-200ms) (200ms-10s) (200ms-10s) HT20 5500 1 < 200ms 200ms 25ms 60ms 1.1925s 10 s 8001 sample bin for measurement 3 bin [200ms~10s] 12 sec Timing Plot EUT Signal 200ms~10s 17 bin for data transmit After ending radar burst 200ms Zoom-in 600 ms Timing Plot 200ms 17 bin after 200ms-10s Report No.: FZ351401 Page : 12 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 Channel Closing Transmission Time Channel Move Time Modulation Freq. Radar Mode (MHz) Type Test Limit Test Limit Test Limit (0-200ms) (0-200ms) (200ms-10s) (200ms-10s) HT40 5510 1 < 200ms 200ms 22.5ms 60ms 1.23s 10s 8001 sample bin for measurement 15 bin [200ms~10s] 12 sec Timing Plot EUT Signal 200ms~10s 15 bin for data transmit After ending radar burst 200ms Zoom-in 600 msTiming Plot 200ms 15 bin after 200ms-10s Report No.: FZ351401 Page : 13 of 14 Report Version: Rev. 01

International Certification Corp. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. Tel: 886-3-271-8666 Fax: 886-3-318-0155 3.2 Non-Occupancy Non-Occupancy Period Result Modulation Non-Occupancy Period Freq. (MHz) Mode Measured Limit Result HT20 5500 >30min 30min Complied 2000 sec Timing Plot ══END══ Report No.: FZ351401 Page : 14 of 14 Report Version: Rev. 01


Document Created: 2019-06-19 14:28:40
Document Modified: 2019-06-19 14:28:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC