Test Rpt_H4IKB8861

FCC ID: H4IKB8861

Test Report

Download: PDF
FCCID_1598510

FCC TEST REPORT REPORT NO.: RF111118D20 MODEL NO.: SK-8861 FCC ID: H4IKB8861 RECEIVED: Nov. 18, 2011 TESTED: Nov. 22 ~ 23, 2011 ISSUED: Nov. 30, 2011 APPLICANT: Lite-On Technology Corporation ADDRESS: 90,Chien I Road, Chung Ho, Taipei Hsien, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This test report consists of 24 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF111118D20 1 Report Format Version 4.0.0

Table of Contents RELEASE CONTROL RECORD..............................................................................3 1. CERTIFICATION ...........................................................................................4 2. SUMMARY OF TEST RESULTS...................................................................5 2.1 MEASUREMENT UNCERTAINTY...............................................................5 3. GENERAL INFORMATION ...........................................................................6 3.1 GENERAL DESCRIPTION OF EUT ............................................................6 3.2 DESCRIPTION OF TEST MODES ..............................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .........................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: .............8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................9 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................9 4. TEST TYPES AND RESULTS .....................................................................10 4.1 CONDUCTED EMISSION MEASUREMENT ............................................10 4.2 RADIATED EMISSION MEASUREMENT .................................................10 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ...............................10 4.2.2 TEST INSTRUMENTS ..............................................................................11 4.2.3 TEST PROCEDURES ...............................................................................12 4.2.4 DEVIATION FROM TEST STANDARD .....................................................12 4.2.5 TEST SETUP ............................................................................................13 4.2.6 EUT OPERATING CONDITIONS ..............................................................13 4.2.7 TEST RESULTS ........................................................................................14 4.3 BAND EDGES MEASUREMENT ..............................................................19 4.3.1 LIMITS OF BAND EDGES MEASUREMENT............................................19 4.3.2 TEST INSTRUMENTS ..............................................................................19 4.3.3 TEST PROCEDURE .................................................................................19 4.3.4 DEVIATION FROM TEST STANDARD .....................................................19 4.3.5 EUT OPERATING CONDITION ................................................................19 4.3.6 TEST RESULTS ........................................................................................19 5. PHOTOGRAPHS OF THE TEST CONFIGURATION..................................22 6. INFORMATION ON THE TESTING LABORATORIES ................................23 7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB .......................................................24 Report No.: RF111118D20 2 Report Format Version 4.0.0

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF111118D20 Original release Nov. 30, 2011 Report No.: RF111118D20 3 Report Format Version 4.0.0

1. CERTIFICATION PRODUCT: Wireless Keyboard BRAND NAME: lenovo MODEL NO.: SK-8861 APPLICANT: Lite-On Technology Corporation TESTED: Nov. 22 ~ 23, 2011 TEST ITEM: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 ANSI C63.10-2009 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: ( Annie Chang / Senior Specialist ) APPROVED BY : , DATE: ( Ken Liu / Manager ) Report No.: RF111118D20 4 Report Format Version 4.0.0

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.249) STANDARD TEST TYPE AND LIMIT RESULT REMARK SECTION Power supply is 3Vdc from 15.207 Conducted Emission Test N/A batteries Radiated Emission Test Band Edge Measurement 15.209 Limit: 50dB less than the Minimum passing margin is 15.249 peak value of fundamental PASS –9.9dB at 2390.00MHz 15.249 (d) frequency or meet radiated emission limit in section 12.209 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Frequency Uncertainty 30MHz ~ 1GHz 3.87 dB Radiated emissions Above 1GHz 3.36 dB Report No.: RF111118D20 5 Report Format Version 4.0.0

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT Wireless Keyboard MODEL NO. SK-8861 FCC ID H4IKB8861 POWER SUPPLY 3Vdc from batteries MODULATION TYPE GFSK OPERATING FREQUENCY 2403MHz ~ 2480MHz NUMBER OF CHANNEL 78 ANTENNA TYPE Printed antenna with -0.91dBi gain ANTENNA CONNECTOR N/A DATA CABLE N/A I/O PORTS N/A ASSOCIATED DEVICES N/A NOTE: 1. The EUT is a transceiver. 2. The above EUT information was declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF111118D20 6 Report Format Version 4.0.0

3.2 DESCRIPTION OF TEST MODES 78 channels are provided to this EUT: FREQ. FREQ. FREQ. FREQ. CHANNEL CHANNEL CHANNEL CHANNEL (MHZ) (MHz) (MHz) (MHz) 1 2403 21 2423 41 2443 61 2463 2 2404 22 2424 42 2444 62 2464 3 2405 23 2425 43 2445 63 2465 4 2406 24 2426 44 2446 64 2466 5 2407 25 2427 45 2447 65 2467 6 2408 26 2428 46 2448 66 2468 7 2409 27 2429 47 2449 67 2469 8 2410 28 2430 48 2450 68 2470 9 2411 29 2431 49 2451 69 2471 10 2412 30 2432 50 2452 70 2472 11 2413 31 2433 51 2453 71 2473 12 2414 32 2434 52 2454 72 2474 13 2415 33 2435 53 2455 73 2475 14 2416 34 2436 54 2456 74 2476 15 2417 35 2437 55 2457 75 2477 16 2418 36 2438 56 2458 76 2478 17 2419 37 2439 57 2459 77 2479 18 2420 38 2440 58 2460 78 2480 19 2421 39 2441 59 2461 20 2422 40 2442 60 2462 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST EUT (Powered from batteries) Test Table Report No.: RF111118D20 7 Report Format Version 4.0.0

3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: EUT Applicable to configure Description mode PLC RE<1G RE≥1G BM - Note √ √ √ - Where PLC: Power Line Conducted Emission RE<1G RE: Radiated Emission below 1GHz RE≥1G: Radiated Emission above 1GHz BM: Bandedge Measurement Note: No need to concern of Conducted Emission due to the EUT is powered by batteries. RADIATED EMISSION TEST (BELOW 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1 GFSK RADIATED EMISSION TEST (ABOVE 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 39, 78 GFSK BANDEDGE MEASUREMENT:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 to 78 1, 78 GFSK TEST CONDITION: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE≥1G 23deg. C, 65% RH 3Vdc Chad Lee RE<1G 24deg. C, 66% RH 3Vdc Chad Lee BM 22deg. C, 75% RH 3Vdc Jun Wu Report No.: RF111118D20 8 Report Format Version 4.0.0

3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (Section 15.249) ANSI C63.4-2003 ANSI C63.10-2009 All test items have been performed and recorded as per the above standards. 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together without any necessary accessory or support unit. Report No.: RF111118D20 9 Report Format Version 4.0.0

4. TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT N/A 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209, 15.249 as following: 15.209 Limit Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 15.249 Limit Field Strength of Field Strength of Fundamental Fundamental Harmonics Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF111118D20 10 Report Format Version 4.0.0

4.2.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL HP Preamplifier 8447D 2432A03504 Mar. 04, 2011 Mar. 03, 2012 HP Preamplifier 8449B 3008A01201 Mar. 04, 2011 Mar. 03, 2012 Agilent Spectrum E4446A MY46180403 Jun. 22, 2011 Jun. 21, 2012 Analyzer Schwarzbeck Antenna VULB 9168 137 Apr. 12, 2011 Apr. 11, 2012 Schwarzbeck Antenna VHBA 9123 480 May 06, 2011 May 05, 2012 ADT. Turn Table TT100 0306 NA NA ADT. Tower AT100 0306 NA NA ADT_Radiated_V Software NA NA NA 7.6.15.9.2 SUHNER RF cable SF102 CABLE-CH6 Aug. 19, 2011 Aug. 18, 2012 Schwarzbeck Horn BBHA 9120-D1 D130 May 16, 2011 May 15, 2012 Antenna Highpass filter WHK Wainwright SN 8 NA NA 3.1/18G-10SS Instruments NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. 5. The FCC Site Registration No. is 447212. Report No.: RF111118D20 11 Report Format Version 4.0.0

4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak method or average method as specified and then reported in data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF111118D20 12 Report Format Version 4.0.0

4.2.5 TEST SETUP Ant. Tower 1-4m Variable 3m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.2.6 EUT OPERATING CONDITIONS Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF111118D20 13 Report Format Version 4.0.0

4.2.7 TEST RESULTS ABOVE 1GHz DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 1 ~ 25GHz DETECTOR Peak (PK) INPUT POWER 3Vdc FUNCTION Average (AV) ENVIRONMENTAL 23deg. C, 65% RH TESTED BY Chad Lee CONDITIONS ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 64.2 PK 74.0 -9.9 1.00 H 274 33.91 30.24 2 2390.00 44.1 AV 54.0 -9.9 1.00 H 274 13.85 30.24 3 2400.00 56.2 PK 74.0 -17.8 1.00 H 274 25.94 30.29 4 2400.00 24.8 AV 54.0 -29.2 1.00 H 274 -5.46 30.29 5 *2403.00 98.9 PK 114.0 -15.1 1.00 H 274 68.64 30.30 6 *2403.00 67.5 AV 94.0 -26.5 1.00 H 274 37.24 30.30 7 4806.00 53.7 PK 74.0 -20.3 1.00 H 291 17.11 36.60 8 4806.00 22.3 AV 54.0 -31.7 1.00 H 291 -14.29 36.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 2390.00 52.3 PK 74.0 -21.7 1.24 V 264 22.10 30.24 2 2390.00 40.8 AV 54.0 -13.2 1.24 V 264 10.59 30.24 3 2400.00 51.8 PK 74.0 -22.2 1.24 V 264 21.54 30.29 4 2400.00 20.4 AV 54.0 -33.6 1.24 V 264 -9.86 30.29 5 *2403.00 94.5 PK 114.0 -19.5 1.24 V 264 64.24 30.30 6 *2403.00 63.1 AV 94.0 -30.9 1.24 V 264 32.84 30.30 7 4806.00 53.2 PK 74.0 -20.8 1.00 V 158 16.62 36.60 8 4806.00 21.8 AV 54.0 -32.2 1.00 V 158 -14.78 36.60 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.104 ms *2 *13 / 100 ms) = -31.4 dB Please see page 17 for plotted duty. Report No.: RF111118D20 14 Report Format Version 4.0.0

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 39 FREQUENCY RANGE 1 ~ 25GHz DETECTOR Peak (PK) INPUT POWER 3Vdc FUNCTION Average (AV) ENVIRONMENTAL 23deg. C, 65% RH TESTED BY Chad Lee CONDITIONS ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2441.00 97.0 PK 114.0 -17.0 1.00 H 291 66.55 30.43 2 *2441.00 65.6 AV 94.0 -28.4 1.00 H 291 35.15 30.43 3 4882.00 52.7 PK 74.0 -21.3 1.00 H 273 15.88 36.79 4 4882.00 21.3 AV 54.0 -32.7 1.00 H 273 -15.52 36.79 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2441.00 92.1 PK 114.0 -21.9 1.23 V 263 61.65 30.43 2 *2441.00 60.7 AV 94.0 -33.3 1.23 V 263 30.25 30.43 3 4882.00 53.0 PK 74.0 -21.0 1.00 V 148 16.20 36.79 4 4882.00 21.6 AV 54.0 -32.4 1.00 V 148 -15.20 36.79 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.104 ms *2 *13 / 100 ms) = -31.4 dB Please see page 17 for plotted duty. Report No.: RF111118D20 15 Report Format Version 4.0.0

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 78 FREQUENCY RANGE 1 ~ 25GHz DETECTOR Peak (PK) INPUT POWER 3Vdc FUNCTION Average (AV) ENVIRONMENTAL 23deg. C, 65% RH TESTED BY Chad Lee CONDITIONS ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 97.2 PK 114.0 -16.8 1.00 H 293 66.67 30.56 2 *2480.00 65.8 AV 94.0 -28.2 1.00 H 293 35.27 30.56 3 2483.50 61.2 PK 74.0 -12.8 1.00 H 293 30.66 30.57 4 2483.50 29.8 AV 54.0 -24.2 1.00 H 293 -0.74 30.57 5 4960.00 51.8 PK 74.0 -22.2 1.00 H 292 14.83 36.99 6 4960.00 20.4 AV 54.0 -33.6 1.00 H 292 -16.57 36.99 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 *2480.00 93.8 PK 114.0 -20.2 1.00 V 95 63.27 30.56 2 *2480.00 62.4 AV 94.0 -31.6 1.00 V 95 31.87 30.56 3 2483.50 57.8 PK 74.0 -16.2 1.00 V 95 27.26 30.57 4 2483.50 26.4 AV 54.0 -27.6 1.00 V 95 -4.14 30.57 5 4960.00 53.7 PK 74.0 -20.3 1.00 V 180 16.71 36.99 6 4960.00 22.3 AV 54.0 -31.7 1.00 V 180 -14.69 36.99 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.104 ms *2 *13 / 100 ms) = -31.4 dB Please see page 17 for plotted duty. Report No.: RF111118D20 16 Report Format Version 4.0.0

20 log (Duty cycle) = 20 log (0.104 ms *2 *13 / 100 ms) = -31.4 dB Report No.: RF111118D20 17 Report Format Version 4.0.0

BELOW 1GHz WORST-CASE DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE Below 1000MHz DETECTOR INPUT POWER 3Vdc Quasi-Peak FUNCTION ENVIRONMENTAL 24deg. C, 66% RH TESTED BY Chad Lee CONDITIONS ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 654.61 25.7 QP 46.0 -20.3 1.12 H 10 1.87 23.84 2 759.52 25.8 QP 46.0 -20.2 1.69 H 13 0.19 25.65 3 790.18 26.0 QP 46.0 -20.0 1.84 H 85 -0.37 26.38 4 830.53 27.4 QP 46.0 -18.6 1.36 H 193 0.39 26.99 5 861.20 27.0 QP 46.0 -19.1 1.14 H 10 -0.41 27.36 6 899.93 27.8 QP 46.0 -18.2 1.08 H 340 0.03 27.78 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 75.19 25.9 QP 40.0 -14.1 1.02 V 52 14.48 11.39 2 791.80 25.6 QP 46.0 -20.4 1.36 V 16 -0.79 26.41 3 816.01 26.8 QP 46.0 -19.2 1.54 V 349 0.03 26.81 4 856.36 27.8 QP 46.0 -18.2 1.14 V 292 0.47 27.31 5 874.11 28.1 QP 46.0 -17.9 1.03 V 10 0.63 27.50 6 930.60 28.3 QP 46.0 -17.7 1.58 V 10 0.12 28.18 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF111118D20 18 Report Format Version 4.0.0

4.3 BAND EDGES MEASUREMENT 4.3.1 LIMITS OF BAND EDGES MEASUREMENT Below –50dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.3.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL SPECTRUM E4446A MY51100050 Oct. 25, 2011 Oct. 24, 2012 ANALYZER NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz and 300 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. The spectrum plots are attached on the following pages. 4.3.4 DEVIATION FROM TEST STANDARD No deviation 4.3.5 EUT OPERATING CONDITION Same as Item 4.2.6 4.3.6 TEST RESULTS The spectrum plots are attached on the following 4 images. D1 line indicates the highest level, and D2 line indicates the 50dB offset below D1. It shows compliance with the requirement in part 15.249(d). Report No.: RF111118D20 19 Report Format Version 4.0.0

Report No.: RF111118D20 20 Report Format Version 4.0.0

Report No.: RF111118D20 21 Report Format Version 4.0.0

5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF111118D20 22 Report Format Version 4.0.0

6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. Copies of accreditation and authorization certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5.phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Email: service.adt@tw.bureauveritas.com Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF111118D20 23 Report Format Version 4.0.0

7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No modifications were made to the EUT by the lab during the test. ---END--- Report No.: RF111118D20 24 Report Format Version 4.0.0


Document Created: 2011-12-02 14:45:38
Document Modified: 2011-12-02 14:45:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC