Rf exposure report_fcc

FCC ID: GPO38874

RF Exposure Info

Download: PDF
FCCID_2697312

FCC RF Exposure FCC ID: GPO38874 Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v05r02 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v05r01Section 4.3.1 Standalone SAR test exclusion considerations:͞ hŶůĞƐƐ ƐƉĞĐŝĨŝĐĂůůLJ ƌĞƋƵŝƌĞĚ ďLJ ƚŚĞ ƉƵďůŝƐŚĞĚ Z& ĞdžƉŽƐƵƌĞ KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-ǁĂLJƌĂĚŝŽƐ͕ŚĂŶĚƐĞƚƐ͕ůĂƉƚŽƉƐΘƚĂďůĞƚƐĞƚĐ͘Ϯϯ͞ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [Ĝf (GHz)] ζ 3.0 for 1-g SAR andζ 7.5 for 10-g extremity SAR, where: Ȉf (GHz) is the RF channel transmit frequency in GHz ȈPower and distance are rounded to the nearest mW and mm before calculation ȈThe result is rounded to one decimal place for comparison Ȉ3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ζ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion.

Conducted Power Results Bluetooth PeakConducted Output Power Mode Channel Frequency(MHz) (dBm) 01 2402 -3.75 GFSK 20 2440 -3.96 40 2480 -4.63 Manufacturing tolerance Bluetooth GFSK (Peak) Channel Channel 00 Channel 20 Channel 40 Target (dBm) -3.0 -3.0 -4.0 Tolerance ±(dB) 1.0 1.0 1.0 Evaluation Results RF output power Antenna SAR Test (including tune-up SAR Test Band/Mode f (GHz) Distance Exclusion tolerance) Exclusion (cm) Threshold dBm mW BT* 2.450 5 -2.00 0.63 0.2 <3.0 Yes Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v05r02. .......................End of Report.........................


Document Created: 2015-07-24 15:36:43
Document Modified: 2015-07-24 15:36:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC