SP816-2 FCC ID report_Rev1.0

FCC ID: FU5SP816

Test Report

Download: PDF
FCCID_4046153

TEST REPORT FCC ID: FU5SP816 Product Name : Z-Wave 500 series Outdoor PIR Model Name : SP816-2 Brand Name : Report No. : PTC18083020903E-FC01 Prepared for Everspring Industry Co Ltd 3F., No.50, Sec. 1, Zhonghua Rd. Tucheng Dist., New Taipei City 236, Taiwan Prepared by DongGuan Precise testing &Certification Corp. Ltd Building D, Baoding Technology Park, Guangming Road 2, Guangming Community, Dongcheng District, Dongguan, Guangdong, China Page 1 of 29

Report No.: PTC18083020903E-FC01 1TEST RESULT CERTIFICATION Applicant’s name : Everspring Industry Co Ltd 3F., No.50, Sec. 1, Zhonghua Rd. Tucheng Dist., New Taipei City 236, Address : Taiwan Manufacture's name : Everspring Industry Co Ltd 3F., No.50, Sec. 1, Zhonghua Rd. Tucheng Dist., New Taipei City 236, Address : Taiwan Product name : Z-Wave 500 series Outdoor PIR Model name : SP816-2 Standards : FCC CFR47 Part 15 Section 15.249 Test procedure : ANSI C63.10: 2013 Test Date : September 18, 2018 to October 12, 2018 Date of Issue : October 12, 2018 Test Result : Pass This device described above has been tested by PTC, and the test results show that the equipment under test (EUT) is in compliance with the requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of PTC, this document may be altered or revised by PTC, personal only, and shall be noted in the revision of the document. Test Engineer: Leo Yang / Engineer Technical Manager: Chris Du / Manager Page 2 of 29

Report No.: PTC18083020903E-FC01 Contents Page 1 TEST RESULT CERTIFICATION .............................................................................................................................. 2 2 TEST SUMMARY ......................................................................................................................................................... 4 3 TEST FACILITY............................................................................................................................................................ 5 4 GENERAL INFORMATION ........................................................................................................................................ 6 4.1 GENERAL DESCRIPTION OF E.U.T............................................................................ 6 5 EQUIPMENT DURING TEST ..................................................................................................................................... 7 5.1 EQUIPMENTS LIST ..................................................................................................... 7 5.2 MEASUREMENT UNCERTAINTY ................................................................................. 8 5.3 DESCRIPTION OF SUPPORT UNITS............................................................................ 9 6 CONDUCTED EMISSION ......................................................................................................................................... 10 6.1 E.U.T. OPERATION ................................................................................................. 10 6.2 EUT SETUP ............................................................................................................. 10 6.3 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ........................................ 11 6.4 MEASUREMENT PROCEDURE: ................................................................................. 11 6.5 CONDUCTED EMISSION LIMIT .................................................................................. 11 6.6 MEASUREMENT DESCRIPTION ................................................................................ 11 6.7 CONDUCTED EMISSION TEST RESULT.................................................................... 11 7 FIELD STRENGTH OF FUNDAMENTAL EMISSION AND RADIATED SPURIOUS EMISSIONS ............. 12 7.1 EUT OPERATION ..................................................................................................... 13 7.2 TEST SETUP ............................................................................................................ 13 7.3 SPECTRUM ANALYZER SETUP ................................................................................ 15 7.4 TEST PROCEDURE................................................................................................... 15 7.5 SUMMARY OF TEST RESULTS ................................................................................. 16 8 20 DB BANDWIDTH MEASUREMENT .................................................................................................................. 20 8.1 TEST PROCEDURE................................................................................................... 20 8.2 TEST RESULT .......................................................................................................... 20 9 BAND EDGES REQUIREMENT .............................................................................................................................. 21 9.1 TEST RESULT .......................................................................................................... 21 10 ANTENNA REQUIREMENT ................................................................................................................................... 23 11 TEST PHOTOS......................................................................................................................................................... 24 12 EUT PHOTOS ........................................................................................................................................................... 25 Page 3 of 29

Report No.: PTC18083020903E-FC01 2 Test Summary Test Items Test Requirement Result AC Power Conducted Emission 15.207 N/A 20dB Bandwidth 15.215(c) PASS Band edge 15.249(d) PASS Field Strength of Fundamental Emissions 15.249(a) PASS 15.249(c) Radiated Spurious Emissions 15.205(a) PASS 15.209(a) Antenna Requirement 15.203 PASS Remark: 1. The EUT only powered by battery, no need to evaluate AC Power Conducted Emission. 2. The EUT is powered by new batteries during the test. Page 4 of 29

Report No.: PTC18083020903E-FC01 3 TEST FACILITY DongGuan Precise testing &Certification Corp. Ltd Building D,Baoding Technology Park,Guangming Road2, Dongcheng District, Dongguan, Guangdong, China, Dongguan, 523129 FCC Registration Number: 790290 A2LA Certificate No.: 4408.01 IC Registration Number: 12191A-1 Page 5 of 29

Report No.: PTC18083020903E-FC01 4 General Information 4.1 General Description of E.U.T. Product Name : Z-Wave 500 series Outdoor PIR Model Name : SP816-2 Operating frequency : 908.42MHz Numbers of Channel : 1 Antenna Type : Internal Antenna Antenna Gain : -5dBi Type of Modulation : FSK Power supply : Battery AA 1.5V*3 Page 6 of 29

Report No.: PTC18083020903E-FC01 5 Equipment During Test 5.1 Equipments List RF Conducted Test Name of Manufacturer Model Serial No. Characteristics Calibration Due Equipment MXG Signal 10Hz-30GHz Agilent N9020A MY56070279 Sep.19, 2019 Analyzer Coaxial Cable CDS 79254 46107086 10Hz-30GHz Sep.19, 2019 Remark: The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list. Radiated Emissions(9KHz-18GHz) Name of Manufacturer Model Serial No. Characteristics Calibration Due Equipment EMI Test Receiver Rohde&Schwarz ESCI 101417 9KHz-3GHz Sep.19, 2019 Loop Antenna Schwarzbeck FMZB 1519 012 9 KHz -30MHz Sep.19, 2019 Bilog Antenna SCHWARZBECK VULB9160 9160-3355 25MHz-2GHz Sep.19, 2019 Preamplifier (low 1MHz-1GHz SCHWARZBECK BBV 9475 9745-0013 Sep.19, 2019 frequency) Cable Schwarzbeck PLF-100 549489 9KHz-3GHz Sep.19, 2019 Spectrum Analyzer Agilent E4407B MY45109572 9KHz-40GHz Sep.19, 2019 Horn Antenna SCHWARZBECK 9120D 9120D-1246 1GHz-18GHz Sep.19, 2019 Power Amplifier LUNAR EM LNA1G18-40 J10100000081 1GHz-26.5GHz Sep.19, 2019 Cable H+S CBL-26 N/A 1GHz-26.5GHz Sep.19, 2019 Page 7 of 29

Report No.: PTC18083020903E-FC01 5.2 Measurement Uncertainty Parameter Uncertainty RF output power, conducted ±1.0dB Power Spectral Density, conducted ±2.2dB Radio Frequency ± 1 x 10-6 Bandwidth ± 1.5 x 10-6 Time ±2% Duty Cycle ±2% Temperature ±1°C Humidity ±5% DC and low frequency voltages ±3% Conducted Emissions (150kHz~30MHz) 3.64dB Radiated Emission(30MHz~1GHz) 5.03dB Radiated Emission(1GHz~25GHz) 4.74dB Remark: The coverage Factor (k=2), and measurement Uncertainty for a level of Confidence of 95% Page 8 of 29

Report No.: PTC18083020903E-FC01 5.3 Description of Support Units Equipment Model No. Series No. N/A N/A N/A Page 9 of 29

Report No.: PTC18083020903E-FC01 6 Conducted Emission Test Requirement: : FCC CFR 47 Part 15 Section 15.207 Test Method: : ANSI C63.10:2013 Test Result: : PASS Frequency Range: : 150kHz to 30MHz Class/Severity: : Class B Detector: : Peak for pre-scan (9kHz Resolution Bandwidth) 6.1 E.U.T. Operation Operating Environment : Temperature: : 25.5 C Humidity: : 51 % RH Atmospheric Pressure: : 101.2kPa 6.2 EUT Setup The conducted emission tests were performed using the setup accordance with the ANSI C63.10: 2013. 0.4m EUT Receiver PC System 0.8m 0.8m LISN :50 Terminator Page 10 of 29

Report No.: PTC18083020903E-FC01 6.3 Test SET-UP (Block Diagram of Configuration) Test Receiver AC Mains L.I.S.N EUT 6.4 Measurement Procedure: 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured was complete. 6.5 Conducted Emission Limit Conducted Emission Frequency(MHz) Quasi-peak Average 0.15-0.5 66-56 56-46 0.5-5.0 56 46 5.0-30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies 2.The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 6.6 Measurement Description The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within 6dB of the average limit line. 6.7 Conducted Emission Test Result N/A. Page 11 of 29

Report No.: PTC18083020903E-FC01 7 Field Strength of Fundamental Emission and Radiated Spurious Emissions Test Requirement: : FCC Part C section 15.205 & 15.209 & 15.249 Test Method: : ANSI C63.10: 2013 Test Result: : PASS Measurement Distance: : 3m Limit: : See the follow table 15.209 limit: Field Strength Field Strength Limit at 3m Measurement Dist Frequency (MHz) Distance uV/m uV/m dBuV/m (m) 0.009 ~ 0.490 2400/F(kHz) 300 10000 * 2400/F(kHz) 20log(2400/F(kHz)) + 80 0.490 ~ 1.705 24000/F(kHz) 30 100 * 24000/F(kHz) 20log(24000/F(kHz)) + 40 1.705 ~ 30 30 30 100 * 30 20log(30) + 40 30 ~ 88 100 3 100 20log(100) 88 ~ 216 150 3 150 20log(150) 216 ~ 960 200 3 200 20log(200) Above 960 500 3 500 20log(500) Note: 1. Emission level in dBuV/m=20 log (uV/m) 2. Measurement was performed at an antenna to the closed point of EUT distance of meters. The field strength of emission from intentional radiators operated within these frequency bands shall comply with the following: 15.249(a) Limit: Fundamental Field strength of fundamental Field strength of harmonics Frequency (MHz) mV/m dBuV/m uV/m dBuV/m 902-928 50 94 500 54 2400-2483.5 50 94 500 54 5725-5875 50 94 500 54 24000-24250 250 108 2500 68 Page 12 of 29

Report No.: PTC18083020903E-FC01 7.1 EUT Operation Operating Environment : Temperature: : 23.5 C Humidity: : 51.1 % RH Atmospheric Pressure: : 101.2kPa Test Voltage : DC 4.5V Battery 7.2 Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site The test setup for emission measurement below 30MHz. Semi-anechoic 3m Chamber Turn Table From 0°to 360° 3m EUT Turn Table 0.8m PC Spectrum AMP Combining System Analyzer Network Page 13 of 29

Report No.: PTC18083020903E-FC01 The test setup for emission measurement from 30 MHz to 1 GHz. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0°to 360° 3m EUT 0.8m Turn Table PC Spectrum AMP Combining System Analyzer Network The test setup for emission measurement above 1 GHz. Page 14 of 29

Report No.: PTC18083020903E-FC01 7.3 Spectrum Analyzer Setup Frequency Detector RBW VBW Remark Below 30MHz -- 10kHz 10kHz -- Quasi-peak Receiver Setup 30MHz ~ 1GHz Quasi-peak 120kHz 300kHz Value Peak 1MHz 3MHz Peak Value Above 1GHz RMS 1MHz 3MHz Average Value 7.4 Test Procedure 1. The testing follows the guidelines in Spurious Radiated Emissions of ANSI C63.10-2013. 2. Below 1000MHz, The EUT was placed on a turn table which is 0.8m above ground plane. And above 1000MHz, The EUT was placed on a styrofoam table which is 1.5m above ground plane. 3. The EUT was set 3 meters from the interference receiving antenna, which was mounted on the top of a variable height antenna tower. 4. For each suspected emission, the EUT was arranged to its worst case and then tune the Antenna tower (From 1m to 4m) and turntable (from 0 degree to 360 degree) to find the maximum reading. A pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 5. Set to the maximum power setting and enable the EUT transmit continuously. 6. Final measurement (Above 1GHz): The frequency range will be divided into different sub ranges depending of the frequency range of the used horn antenna. The EMI Receiver set to peak and average mode and a resolution bandwidth of 1MHz. The measurement will be performed in horizontal and vertical polarization of the measuring antenna and while rotating the EUT in its vertical axis in the range of 0 degree to 360 degree in order to have the antenna inside the cone of radiation. 7. Test Procedure of measurement (For Above 1GHz): 1) Monitor the frequency range at horizontal polarization and move the antenna over all sides of the EUT(if necessary move the EUT to another orthogonal axis). 2) Change the antenna polarization and repeat 1) with vertical polarization. 3) Make a hardcopy of the spectrum. 4) Measure the frequency of the detected emissions with a lower span and resolution bandwidth to increase the accuracy and note the frequency value. 5) Change the analyser mode to Clear/ Write and found the cone of emission. 6) Rotate and move the EUT, so that the measuring distance can be enlarged to 3m and the antenna will be still inside the cone of emission. Page 15 of 29

Report No.: PTC18083020903E-FC01 7) Measure the level of the detected frequency with the correct resolution bandwidth, with the antenna polarization and azimuth and the peak and average detector, which causes the maximum emission. 8) Repeat steps 1) to 7) for the next antenna spot if the EUT is larger than the antenna beamwidth. 8. The radiation measurements are tested under 3-axes(X,Y,Z) position(X denotes lying on the table, Y denotes side stand and Z denotes vertical stand), After pre-test, It was found that the worse radiation emission was get at the X position. So the data shown was the X position only. 7.5 Summary of Test Results Test Frequency: 9KHz-30MHz Freq. Ant.Pol. Emission Level Limit 3m Over (MHz) H/V (dBuV/m) (dBuV/m) (dB) -- -- -- -- >20 Note: The amplitude of spurious emission that is attenuated by more than 20dB below the permissible limit has no need to be reported. Distance extrapolation factor =40log(Specific distance/ test distance)( dB); Limit line=Specific limits(dBuV) + distance extrapolation factor. Test Frequency: 30MHz ~ 1GHz Page 16 of 29

Report No.: PTC18083020903E-FC01 Horizontal: Page 17 of 29

Report No.: PTC18083020903E-FC01 Vertical: Page 18 of 29

Report No.: PTC18083020903E-FC01 Fundamental and Harmonics Average Result Frequency Emission Level Limit Margin Ant. Polar Detector (MHz) (dBμV/m) (dBμV/m) (dB) H/V 908.420 84.66 94 -9.34 H QP 908.420 85.09 94 -8.91 V QP Test Frequency 1GHz-10GHz: Emission Freq. Ant.Pol. Level(dBuV/m) Limit 3m(dBuV/m) Margin(dB) (MHz) H/V PK AV PK AV PK AV 1816.84 V 54.32 45.62 74.00 54.00 -19.68 -8.38 2725.26 V 53.05 43.29 74.00 54.00 -20.95 -10.71 3633.68 V 51.62 42.05 74.00 54.00 -22.38 -11.95 4542.10 V 50.29 41.72 74.00 54.00 -23.71 -12.28 5450.52 V 48.72 38.65 74.00 54.00 -25.28 -15.35 6358.94 V 46.35 37.21 74.00 54.00 -27.65 -16.79 1816.84 H 55.07 44.19 74.00 54.00 -18.93 -9.81 2725.26 H 54.16 43.06 74.00 54.00 -19.84 -10.94 3633.68 H 52.09 42.58 74.00 54.00 -21.91 -11.42 4542.10 H 51.47 40.62 74.00 54.00 -22.53 -13.38 5450.52 H 48.37 37.58 74.00 54.00 -25.63 -16.42 6358.94 H 46.22 35.69 74.00 54.00 -27.78 -18.31 Remark: 1. Margin= Emission Level - Limit 2. “*” means the test results were attenuated more than 20dB below the permissible limits, so the results don’t record in the report. Page 19 of 29

Report No.: PTC18083020903E-FC01 8 20 dB Bandwidth Measurement Test Method : ANSI C63.10: 2013 8.1 Test Procedure 1. Remove the antenna from the EUT and then connect a low RF cable from the antenna port to the spectrum; 2. Set the spectrum analyzer: RBW = 1kHz, VBW = 3kHz 8.2 Test Result 20dB Down Channel frequency (MHz) BW(KHz) 908.42 62.27 Page 20 of 29

Report No.: PTC18083020903E-FC01 9 Band edges Requirement Test Requirement: FCC Part 15 C section 15.249(d) (d) Emission radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50dB below the level of the fundamental or to the general radiated emission limits in 15.209, whichever is the lesser attenuation. Test Method: ANSI C63.10: Clause 6.10 Test Status: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports(if EUT with antenna diversity architecture). The lowest, middle and highest channels were selected for the final test as listed below. 9.1 Test Result Page 21 of 29

Report No.: PTC18083020903E-FC01 Page 22 of 29

Report No.: PTC18083020903E-FC01 10 Antenna Requirement The antenna is permanently attached on PCB, no consideration of replacement. Please refer to internal Photos for details. Page 23 of 29

Report No.: PTC18083020903E-FC01 11 TEST PHOTOS Test Frequency From 30MHz-1000MHz Test frequency from 1GHz-10GHz Page 24 of 29

Report No.: PTC18083020903E-FC01 12 EUT PHOTOS Page 25 of 29

Report No.: PTC18083020903E-FC01 Page 26 of 29

Report No.: PTC18083020903E-FC01 Page 27 of 29

Report No.: PTC18083020903E-FC01 Page 28 of 29

Report No.: PTC18083020903E-FC01 ******THE END REPORT****** Page 29 of 29


Document Created: 2018-10-23 13:29:47
Document Modified: 2018-10-23 13:29:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC