Test Report

FCC ID: FSUGKZGC

Test Report

Download: PDF
FCCID_181185

FCC ID: FSUGKZGC FCC TEST REPORT REPORT NO.: RF901030R04 MODEL NO.: TK2702 RECEIVED: Oct. 30, 2001 TESTED: Nov. 5 ~ Nov. 8, 2001 APPLICANT: KYE SYSTEMS CORP. ADDRESS: No.492 SEC.5, CHUNG HSIN RD., SAN CHUNG, TAIPEI HSIEN 241, TAIWAN, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chia Pau Tsuen, Linkou Hsiang, Taipei, Taiwan, R.O.C. This test report consists of 14 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by NVLAP or any U.S. government agencies. The test results in the report only apply to the tested sample. Lab Code: 200102-0 0528 ILAC MRA Report No.: RF901030R04 1 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC Table of Contents 1 CERTIFICATION..............................................................................................3 2 SUMMARY OF TEST RESULTS .....................................................................4 3 GENERAL INFORMATION..............................................................................5 3.1 GENERAL DESCRIPTION OF EUT ................................................................5 3.2 DESCRIPTION OF TEST MODES ..................................................................6 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .................................6 3.4 DESCRIPTION OF SUPPORT UNITS ............................................................6 4 TEST PROCEDURE AND RESULT ................................................................7 4.1 CONDUCTED EMISSION MEASUREMENT...................................................7 4.2 RADIATED EMISSION MEASUREMENT........................................................7 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT .....................................7 4.2.2 TEST INSTRUMENT .......................................................................................8 4.2.3 TEST PROCEDURE........................................................................................9 4.2.4 TEST SETUP.................................................................................................10 4.2.5 EUT OPERATING CONDITION.....................................................................10 4.2.6 TEST RESULT............................................................................................... 11 5 PHOTOGRAPHS OF THE TEST CONFIGURATION ....................................13 6 INFORMATION ON THE TESTING LABORATORIES ..................................14 Report No.: RF901030R04 2 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 1 CERTIFICATION PRODUCT : Wireless Keyboard BRAND NAME : KYE, Monterey MODEL NO : TK2702 APPLICANT : KYE SYSTEMS CORP. STANDARDS : 47 CFR Part 15, Subpart C(15.227) ANSI C63.4-1992 We, Advance Data Technology Corporation, hereby certify that one sample of the designation has been tested in our facility from Nov. 5, 2001 ~ Nov.8, 2001. The test record, data evaluation and Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample's EMC characteristics under the conditions herein specified. Report No.: RF901030R04 3 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: 47 CFR Part 15, Subpart C STANDARD TEST TYPE RESULT REMARK PARAGRAPH Power supply is 3VDC 15.107 Conducted Emission Test N/A from batteries Minimum passing 15.227 Radiated Emission Test PASS margin is –10.00dBuV at 461.39MHz NOTE: The receiver part to communicate with the EUT has been verified to comply with FCC Part 15, Subpart B, Class B (DoC). The test report can be provided upon request. Report No.: RF901030R04 4 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT Wireless Keyboard MODEL NO. TK2702 POWER SUPPLY 3VDC from battery MODULATION TYPE FSK CARRIER FREQUENCY 27.145 MHz OF EACH CHANNEL BANDWIDTH OF EACH 10KHz CHANNEL NUMBER OF CHANNEL 1 ANTENNA TYPE Wired antenna DATA CABLE NA I/O PORTS NA ASSOCIATED DEVICES NA NOTE: 1. The EUT is the transmitter part of a Wireless Keyboard. 2. The EUT has two brand names due to marketing requirement. 3. For more detailed features description of the EUT, please refer to the manufacturer's specifications or the User's Manual. Report No.: RF901030R04 5 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 3.2 DESCRIPTION OF TEST MODES One channel is provided in this EUT. Channel Frequency Channel Frequency 1 27.145 MHz 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is the transmitter part of a Wireless Keyboard. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC CFR 47 Part 15, Subpart C (15.227) ANSI C63.4-1992 All tests have been performed and recorded as per the above standards. 3.4 DESCRIPTION OF SUPPORT UNITS NA Report No.: RF901030R04 6 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 4 TEST PROCEDURE AND RESULT 4.1 CONDUCTED EMISSION MEASUREMENT NA 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT According to 15.227 the field strength of emissions from intentional radiators operated under these frequencies bands shall not exceed the following: Fundamental Frequency Field Strength of Fundamental (dBuV/m) (MHz) Peak Average 26.96-27.28 100 80 Field strength limits are at the distance of 3 meters, emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Other Frequencies Field Strength of Fundamental (MHz) uV/meter dBuV/meter 30-88 100 40.0 88-216 150 43.5 216-960 200 46.0 Above 960 500 54.0 As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF901030R04 7 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 4.2.2 TEST INSTRUMENT DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL *HP Spectrum Analyzer 8590L 3544A01176 May 7, 2002 *HP Preamplifier 8447D 2944A08485 May 7, 2002 HP Preamplifier 8449B 3008A01201 Dec. 13, 2001 HP Preamplifier 8449B 3008A01292 Aug. 21, 2002 * ROHDE & SCHWARZ TEST 839013/007 ESMI Jan. 25, 2002 RECEIVER 839379/002 SCHWARZBECK Tunable VHA 9103 E101051 Nov. 23, 2002 Dipole Antenna UHA 9105 E101055 * CHASE BILOG Antenna CBL6112A 2221 Aug. 2, 2002 * SCHWARZBECK Horn BBHA9120- D130 July 6, 2002 Antenna D1 EMCO Horn Antenna 3115 9312-4192 April 15, 2002 * EMCO Turn Table 1060 1115 NA * SHOSHIN Tower AP-4701 A6Y005 NA * Software AS61D4 NA NA * ANRITSU RF Switches MP59B M35046 Aug. 2, 2002 CABLE-ST5- * TIMES RF cable LMR-600 Aug. 2, 2002 01 Open Field Test Site Site 5 ADT-R05 July 28, 2002 FCC: 90422 Site Registration No. Canada IC: IC 3789 VCCI : R-1039 NOTE: 1.The measurement uncertainty is less than +/- 3.0dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months. And the calibrations are traceable to NML/ROC and NIST/USA. 3. “*” = These equipment are used for the final measurement. 4. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz. Report No.: RF901030R04 8 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 4.2.3 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re- tested one by one using the quasi-peak method or average method as specified and then reported in Data sheet peak mode and QP mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 300 Hz for Average detection (AV) at frequency above 1GHz. Report No.: RF901030R04 9 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 4.2.4 TEST SETUP For the actual test configuration, please refer to the related item in this test report - Photographs of the Test Configuration. 4.2.5 EUT OPERATING CONDITION Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF901030R04 10 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 4.2.6 TEST RESULT EUT Wireless Keyboard MODEL TK2702 FREQUENCY MODE Channel 1 30-1000 MHz RANGE DETECTOR Peak / Quasi-Peak / INPUT POWER 3VDC FUNCTION Average ENVIRONMENTAL 25 deg. C, 70 % RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Antenna Cable Pre-Amp. Correction Freq. Limit Margin No. Level Height Angle Value Factor Factor Factor Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB) (dB) (dB) (dB) 1 *27.15 60.6 PK 100.00 -39.40 2.38H 3 75.70 11.35 0.57 27.00 15.08 2 *27.15 56.9 AV 80.00 -23.10 2.38H 3 45.00 11.35 0.57 0.00 -11.92 3 108.90 29.0 QP 43.50 -14.50 1.68H 211 17.00 11.03 1.02 0.00 -12.05 4 162.87 27.5 QP 43.50 -16.00 1.84H 355 16.70 9.53 1.28 0.00 -10.82 5 190.47 27.7 QP 43.50 -15.80 1.72H 196 17.40 8.95 1.39 0.00 -10.34 6 217.00 29.5 QP 46.00 -16.50 1.97H 268 18.00 9.97 1.50 0.00 -11.48 7 244.54 31.2 QP 46.00 -14.80 2.05H 96 18.00 11.56 1.63 0.00 -13.20 8 271.45 33.3 QP 46.00 -12.70 1.35H 295 19.00 12.53 1.72 0.00 -14.26 9 298.56 35.1 QP 46.00 -10.90 1.43H 20 20.00 13.18 1.88 0.00 -15.07 10 325.40 31.7 QP 46.00 -14.30 1.68H 352 16.00 13.72 1.96 0.00 -15.68 11 352.40 31.5 QP 46.00 -14.50 1.12H 72 15.10 14.31 2.05 0.00 -16.37 12 380.25 32.2 QP 46.00 -13.80 1.17H 334 14.70 15.31 2.16 0.00 -17.47 13 407.40 33.4 QP 46.00 -12.60 1.22H 301 15.00 16.14 2.27 0.00 -18.41 14 434.65 34.3 QP 46.00 -11.70 1.03H 53 15.70 16.29 2.36 0.00 -18.65 15 461.39 36.0 QP 46.00 -10.00 1.00H 93 17.00 16.58 2.43 0.00 -19.01 16 488.53 34.5 QP 46.00 -11.50 1.04H 263 15.00 17.04 2.48 0.00 -19.52 17 515.24 33.0 QP 46.00 -13.00 1.04H 257 13.00 17.46 2.55 0.00 -20.01 NOTE: 1. Emission level = Raw Value – Correction Factor 2. Correction Factor = Pre-Amplifier Factor - Antenna Factor - Cable Factor (Pre-Amplifier Factor = 0, when a Pre-Amplifier is not used for the test.) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5.”∗”= Fundamental frequency. Report No.: RF901030R04 11 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC EUT Wireless Keyboard MODEL TK2702 FREQUENCY MODE Channel 1 30-1000 MHz RANGE DETECTOR Peak / Quasi-Peak / INPUT POWER 3VDC FUNCTION Average ENVIRONMENTAL 25 deg. C, 70 % RH, TESTED BY: Gary Chang CONDITIONS 1050 hPa ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Antenna Cable Pre-Amp. Correction Freq. Limit Margin No. Level Height Angle Value Factor Factor Factor Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB) (dB) (dB) (dB) 1 *27.15 53.0 PK 100.00 -47.00 1.10V 353 68.10 11.35 0.57 27.00 15.08 2 *27.15 49.1 AV 80.00 -20.90 1.10V 353 37.20 11.35 0.57 0.00 -11.93 3 162.77 26.8 QP 43.50 -16.70 2.74V 249 16.00 9.53 1.28 0.00 -10.81 4 217.13 29.5 QP 46.00 -16.50 2.74V 73 18.00 9.97 1.50 0.00 -11.47 5 244.45 30.7 QP 46.00 -15.30 1.58V 320 17.50 11.56 1.63 0.00 -13.19 6 270.40 31.0 QP 46.00 -15.00 1.86V 9 16.80 12.47 1.71 0.00 -14.18 7 298.55 31.1 QP 46.00 -14.90 1.41V 198 16.00 13.18 1.88 0.00 -15.06 8 407.11 28.8 QP 46.00 -17.20 1.39V 211 10.40 16.14 2.27 0.00 -18.41 9 434.26 29.4 QP 46.00 -16.60 1.73V 106 10.80 16.29 2.36 0.00 -18.65 10 461.38 30.0 QP 46.00 -16.00 1.29V 332 11.00 16.58 2.43 0.00 -19.01 11 488.53 29.5 QP 46.00 -16.50 1.41V 55 10.00 17.04 2.48 0.00 -19.52 NOTE:1. Emission level = Raw Value – Correction Factor 2. Correction Factor = Pre-Amplifier Factor - Antenna Factor - Cable Factor (Pre-Amplifier Factor = 0, when a Pre-Amplifier is not used for the test.) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5.”∗”= Fundamental frequency. Report No.: RF901030R04 12 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 5 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST Report No.: RF901030R04 13 Issued: Nov. 26, 2001

FCC ID: FSUGKZGC 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP Germany TUV Rheinland Japan VCCI New Zealand MoC Norway NEMKO R.O.C. BSMI, DGT, CNLA Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Lin Kou EMC Lab: Hsin Chu EMC Lab: Tel: 886-2-26052180 Tel: 886-35-935343 Fax: 886-2-26052943 Fax: 886-35-935342 Lin Kou Safety Lab: Lin Kou RF&Telecom Lab: Tel: 886-2-26093195 Tel: 886-3-3270910 Fax: 886-2-26093184 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF901030R04 14 Issued: Nov. 26, 2001


Document Created: 2001-11-27 09:26:44
Document Modified: 2001-11-27 09:26:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC