6

FCC ID: FSUGEPRO

Test Report

Download: PDF
FCCID_38869

SPORTON INTERNATIONAL INC. ee SPORTON LAB. FCC TEST REPORT Report No. : F931001 FCC TEST REPORT for CISPR PUB. 22 Class B Equipment : Tablet Model No. : Easy Pen Pro FCC ID : FSUGEPRO Filing Type : Original Grant Applicant : KYE Systems Corp. No. 492, Sec. 5, Chung Hsin Rd., San Chung, Taipei Hsien, 241, Taiwan, R.O.C. The test result refers exclusively to the test presented test model / sample. Without the written authorization of the test lab., the Test Report may not be copied. Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of U.S. government. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 1 of 22 v nes n nene anee

FCC TEST REPORT Report No. : F931001 Table of Contents CERTIFICATE OF COMPLIANCE ...................... Cerveeveernreeererreerereeevecrecrerreerencervenveeseerievernennnecnernenvveerenseevensennevenne 3 1. General Description of Equipment under Test sn e a m 1.1. Applicant... 1.2. Manufacturer, 1.3. Basic Description of Equipment under Test 1.4. FO@UTG OF EQUIDTNGTUMO®T TeS......c....ccccclncnnnnnnnneeeenneernnre en e cereanreceereaneaevernecerne reverveaveparcereeneceereene n1 vnvsecnnreerserneccenn 2. Test Configuration of Equipment under Test vao ut 2.1. TGSb M@NN@T......s ucss cenmee emnerenenmnerrennereerenmnnnecnen 2.2. Description of Test System ............. 2.3. Connection Diagram of Test System 3. Test Software. ® 4. General Information of Test w © © v o 0# 4.1. Test Facility.... 4.2. Standard for Methods ofMeasuremen 4.3. Test in Compliance with ..................... 4.4. Frequency Range Investigated 4.5. T@St DiSI@NG®........cccssccccsnccsee> 5. Test of Conducted Powerline 5.1. Major Measuring Instruments ... 5.2. Test Procedures... . 5.3. Typical Test Setup Layoul of Conducted Powemns 5.4. Test Result of AC Powerline Conducted Emission ..... 5.5. Photographs of Counducted Powerline Test Configuration. 6. TGSt Of RAGI@t@U EMISSION ................ccceseserseevennneennreveesrevercennenneesevbenneereeneceves serveveeeneneveerver reennenvenverennenen ces 16 6.1. Major Measuring Instruments 6.2. Test Procedures... . 6.3. Typical Test Setup Layout of Radiated Emissio 6.4. Test Result of Radiated Emission ... 6.5. Photographs of Radiated Emission Test Configuration 7. ANt@ANA FACtOT & CABI® LOSS ................cccccsseversenenercverserersenrenneerverecrerecnrnenenervecorvenerennnerecnsee venemeermmnverenserces 21 8. List of Measuring Equipments Used... .......... 22 SPORTON International Inc. FCC iD : FSUGEPRO 1220 00200222 mollail L n ceas

SPORTON INTERNATIONAL INC. ee SPORTON LAB. FCC TEST REPORT Report No. : F931001 Certificate No. ; F931001 CERTIFICATE OF COMPLIANCE for CISPR PUB. 22 Class B Equipment : Tablet Model No. : Easy Pen Pro FCC ID : FSUGEPRO Applicant : KYE Systems Corp. No. 492, Sec. 5, Chung Hsin Rd., San Chung, Taipei Hsien, 241, Taiwan, R.O.C. i HEREBY certiey that : The measurements shown in this test report were made in accordance with the procedures given in ANSI C63.4 — 1992 and the energy emitted by this equipment was passed CISPR PUB. 22 both radiated and conducted emission class B limits. Testing was carried out on Mar. 16, 1999 at SPORTON International Inc. LAB. in Lin Kou. / Mar *7 7/ W,. L. Huang 4 General Manager / SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 3 of 22

FCC TEST REPORT Report No. : F931001 1. General Description of Equipment under Test 1.1. Applicant KYE Systems Corp. No. 492, Sec. 5, Chung Hsin Rd., San Chung, Taipei Hsien, 241, Taiwan, R.O.C. 1.2. Manufacturer Same as 1.1. 1.3. Basic Description of Equipment under Test Equipment : Tablet Model No. : Easy Pen Pro FCC ID : FSUGEPRO Trade Name : KYE SYSTEMS CORP. Data Cable from tablet to PC COM Port : Non—Shielded, 1.85 m Data cable from keyboard connector of EUT to PC COM port : Non—Shielded, 0.79 m Power Supply Type : From PC Power Cord : N/A 1.4. Feature of Equipment under Test Platform Support: PC Hardware Interface: RS—232 Software Driver: GeniTab II for Windows3.x, 95, 98, NT3.x, 4.x Resolution :Up to 2,540LP! Accuracy: 0.01 inch Proximity: 10 mm from surface of tablet Working Area: Horizontal 5 inches, Vertical 3.75 inches Baud Rate :Up to 19200 Report Rate: Up to 135 RPS in 9600 baud Protocol:5 or 3 byted binary format Power Source: Keyboard port through adapter Operation mode: Stream, SW stream, Point, Remote Request etc. Technology: Electromagnetic with cordiess transaction Cursor Support :S—09W Cordless pen Stylus: A ball point pen like pointing device, that deliver electromagnetic flux to tablet to point out where position is. One tip button like mouse "left button" and barre! button as "right and middle button". Both tip and barrel button function are definable by user‘s choice. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 4 of 22

FCC TEST REPORT Report No. : F931001 2. Test Configuration of Equipment under Test 2.1. Test Manner a. The EUT has been associated with personal computer and peripherals pursuant to ANSI C63.4—1992 and configuration operated in a manner which tended to maximize its emission characteristics in a typical application. b. The SONY Monitor, DELL PS/2 Keyboard, PRIMAX PS/2 Mouse, HP Printer, ACEEX Modem and EUT were connected to the FIC PC for EMI test. c. Frequency range investigated: conduction 150 KHz to 30 MHz, radiation 30 MHz to 1,000 MHz. 2.2. Description of Test System Support Unit 1. —— Personal Computer (FIC) FCCID : N/A Model No. : P2L97 Power Supply Type : Switching Power Cord : Non—Shielded Serial No. : SPOO06 Data Cable : Shielded, 360 degree via metal backshells Remark : This support device was tested to compy with FCC standards and authorized under a declaration of conformity. Support Unit 2. —— Monitor (SONY) FCC ID : AK8GDMA17SE2T Model No. : GDM—17SE2T Power Supply Type : Switching Power Cord : Non—Shielded Serial No. : $P0072 Data Cable : Double—Shielded, 360 degree via metal backshells, 1.7m Support Unit 3. —— PS/2 Keyboard (DELL) FCC ID : GYUM92SK Model No. : AT101(DEBM) Serial No. : SP0054 Data Cable : Shielded, 360 degree via metal backshells, 1.9m SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 5 of 22

FCC TEST REPORT Report No. : F931001 Support Unit 4. —— PS/2 Mouse (PRIMAX) FCC ID : EMJMUSJQ Model No. : MUSIJ Serial No. : $PO045 Data Cable : Shielded, 360 degree via metal backshells, 1.7m Support Unit 5. —— Printer (HP) FCC ID : B94C2642X Model No. : DeskJet 400 Power Supply Type : Linear Power Cord : Non—Shielded Serial No. : $PO048 Data Cable : Braided—Shielded, 360 degree via metal backshells, 1.35m Support Unit 6. —— Modem (ACEEX) FCC ID : IFAXDM1414 Model No. : DM1414 Power Supply Type : Linear Power Cord : N/A Serial No. : SPOO76 Data Cable : Braided—Shielded, 360 degree via metal backshells,1.15m SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 6 of 22

FCC TEST REPORT Report No. : F931001 2.3. Connection Diagram of Test System 5 6 2 Printer Modem Monitor PC 4 3 4 z_ PEN 7# Keyboard Mouse EuT The 1/O cable is connected from the EUT to the support device 1. oc The I/O cable is connected from PC to the support device 2. m The I/O cable is connected from EUT to the support device 3. w The 1/O cable is connected from PC to the support device 4. A The 1/O cable is connected from PC to the support device 5. m The I/O cable is connected from PC to the support device 6. 9 SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 7 of 22

FCC TEST REPORT Report No. : F931001 3. Test Software An executive program, EMITEST.EXE under WIN 98, which generates a complete line of continuously repeating " H " pattern was used as the test software. The program was executed as follows : a. Turn on the power of all equipment. b. The PC reads the test program from the floppy disk drive and runs it. c. The PC sends " H" messages to the monitor, and the monitor displays " H " patterns on the screen. d. The PC sends " H " messages to the printer, then the printer prints them on the paper. e. The PC sends " H " messages to the modem. f. The PC sends " H" messages to the internal Hard Disk, and the Hard Disk reads and writes the message. g. Repeat the steps from b to f. An executive programs, Paint under WINQ8, was used as the test software. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 8 of 22 FAX : 886—2—2696—2255 Issued Date : Mar. 19. 1999

FCC TEST REPORT Report No. : F931001 4. General Information of Test 4.1. Test Facility This test was carried out by SPORTON International Inc. in an openarea test site. Openarea Test Site Location : No. 30—2, Lin 6, Diing—Fwu Tsuen, Lin—Kou—Hsiang, Taipei Hsien, Taiwan, R.O.C. TEL : 886—2—2601—1640 FAX : 886—2—2601—1695 4.2. Standard for Methods of Measurement ANSI C63.4—1992 4.3. Test in Compliance with CISPR PUB. 22 Class B 4.4. Frequency Range Investigated a. Conduction: from 150 kHz to 30 MHz b. Radiation : from 30 MHz to 1,000 MHz 4.5. Test Distance The test distance of radiated emission from antenna to EUT is 10 M. SPORTON International Inc. FCC iD : FSUGEPRO —2696—2468 Page No. : 9 of 22

FCC TEST REPORT Report No. : F931001 5. Test of Conducted Powerline Conducted Emissions were measured from 150 kHz to 30 MHz with a bandwidth of 9 KHz on the 115 VAC power and return leads of the EUT according to the methods defined in ANSI C63.4—1992 Section 3.1. The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane as shown in section 5.3. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position produced maximum conducted emissions. 5.1. Major Measuring Instruments Test Receiver HP 8591EM Attenuation 0 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz Step MHz 0.007 MHz IF Bandwidth 9 kHz SPORTON International Inc. FCC ID : FSUGEPRO

FCC TEST REPORT Report No. : F931001 5.2. Test Procedures The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least 80 centimeters from any other grounded conducting surface. Connect EUT to the power mains through a line impedance stabilization network (LISN). 3 a ~m poa o & All the support units are connect to the other LISN. The LISN provides 50 ohm coupling impedance for the measuring instrument. The FCC states that a 50 ohm, 50 microhenry LISN should be used. Both sides of AC line were checked for maximum conducted interference. The frequency range from 150 kHz to 30 MHz was searched. Set the test—receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. If the emission level of the EUT in peak mode was 6 dB lower than the limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 6 dB margin will be retested one by one using the quasi—peak method and reported. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 11 of 22

FCC TEST REPORT Report No. : F931001 5.3. Typical Test Setup Layout of Conducted Powerline 10 cm \Q [~—B —s _. 1 U \Z__J NV _/ _/ ;/ 80 cm to the ground plane L.1.S.N. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 12 of 22

FCC TEST REPORT Report No. : F931001 5.4. Test Result of AC Powerline Conducted Emission Frequency Range of Test : from 0.15 MHz to 30 MHz Temperature : 20°C Relative Humidity : 69 % Test Date : Mar. 16, 1999 The Conducted Emission test was passed at minimum margin LINE 0.253MHz /48.20 dBuV. Freq. Line Meter Reading Limits Margin or qPr _AV. GP. AV. QP.__AV. QP. AV. QP. AV. (MHz) Neutral (dBuv) (dBuv) (uV) (uv (dBuy) (dBuv) (uv) uV (d8) (08) .253 L 48.20 4740 257.04 234.42 61.65 51.65 1208.96 382.31 —1345 4.25 0.533 L 28.30 25.30 26.00 1841 56.00 46.00 630.96 199.53 —27.70—20.70 22.570 L 37.50 34.70 74.99 54.33 60.00 50.00 1000.00 316.23 —22.50 —15.30 0.253 N 45.60 45.50 190.55 188.36 61.66 51.66 1210.33 382.74 —16.06 —6.16 0.533 N 27.70 2410 24.27 16.03 56.00 46.00 630.96 199.53 —28.30 —21.90 22.570 N 39.40 35.40 93.33 58.88 60.00 50.00 1000.00 316.23 —20.60 —14.60 f Test Engineer: !S Qfiflz (—/&ké’l KENNY{LEHUANG SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 13 of 22 FAX : 886—2—2696—2255 Issued Date : Mar. 19, 1999

FCC TEST REPORT Report No. : F931001 6. Test of Radiated Emission Radiated emissions from 30 MHz to 1,000 MHz were measured with a bandwidth of 120 kHz according to the methods defines in ANSI C63.4—1992. The EUT was placed on a nonmetallic stand in the open—field site, 0.8 meter above the ground plane, as shown in section 6.3. The interface cables and equipment positions were varied within limits of reasonable applications to determine the positions producing maximum radiated emissions. 6.1. Major Measuring Instruments Amplifier (HP 8447D) Attenuation 0 dB RF Gain 25 dB Signal Input 0.1 MHz to 1.3 GHz Spectrum Analyzer (HP 8568B) Attenuation 0 dB Start Frequency 30 MHz Stop Frequency 1,000 MHz Resolution Bandwidth 1 MHz Video Bandwidth 1 MHz Signal Input 100 Hz to 1.5 GHz Quasi—Peak Adapter (85650A) Resolution Bandwidth 120 KHz Frequency Band 30 MHz to 1 GHz Quasi—Peak Detector ON for Quasi—Peak Mode OFF for Peak Mode SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 16 of 22

FCC TEST REPORT Report No. : F931001 6.2. Test Procedures a. The EUT was placed on a rotatable table top 0.8 meter above ground. b. The EUT was set 10 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. c. The table was rotated 360 degrees to determine the position of the highest radiation. d. The antenna is a half wave dipole and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. e. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower {from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. f. Set the test—receiver system to Peak Detect Function and specified bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 6 dB lower than the limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 6 dB margin will be repeated one by one using the quasi—peak method and reported. SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 17 of 22

FCC TEST REPORT Report No. : F931001 6.3. Typical Test Setup Layout of Radiated Emission Antenna A N Equipment under Test t— «_ 10 M for FCC test Ground Plane 1 N_ 1 TumTable Receiver SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2606—2468 Page No. : 18 of 22

FCC TEST REPORT Report No. : F931001 6.4. Test Result of Radiated Emission Frequency Range of Test : from 30 MHz to 1,000 MHz Test Distance : 10 M Temperature : 19°C Relative Humidity : 74 % Test Date : Mar. 15, 1999 Emission level (dBuV/m) = 20 log Emission level (uV/m) Corrected Reading : Antenna Factor + Cable Loss + Reading = Emission The Radiated Emission test was passed at minimum margin 165.900 MHz / 26.63 dBuV (HORIZONTAL) Antenna Height 4 Meter, Turntable Degree 12 °. Frequency Antenna Cable Reading Limits Emission Level Margin Polarity Factor Loss =——————— (MHz) {dB/m) (dB) (dBuV) (dBuV/m) (uV/m) (dBuV/m) (uV/im) (dB) 77.400 H 7.00 0.95 17.61 30.00 31.62 25.56 18.97 ~4.44 127.200 H 1218 1.24 12.04 30.00 31.62 2546 18.75 ~4.54 143.800 H 11.20 1.24 12.67 30.00 31.62 25.11 18.01 —4.89 149.300 H 10.60 1.29 14.42 30.00 31.62 26.31 20.68 —3.69 165.900 H 10.08 1.36 15.19 30.00 31.62 26.63 2145 —3.37 193.500 H 8.92 1.40 15.41 30.00 31.62 25.73 19.34 ~4.27 Test Engineer: gme"? ?""\ JONES JAN SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 19 of 22

FCC TEST REPORT Report No. : F931001 7. Antenna Factor & Cable Loss Frequency (MHz) Antenna Factor (dB) Cable Loss (dB) 30 17.9 0.8 35 16.1 0.8 40 14.0 0.8 45 10.5 0.8 50 7.9 0.7 55 6.7 0.8 60 5.5 0.9 65 5.5 0.8 70 5.6 0.9 75 6.5 1.0 80 7.5 0.9 85 8.5 1.0 90 9.4 1.0 95 10.4 1.0 100 11.5 1.1 110 12.1 1.1 120 12.6 11 130 12.0 1.3 140 1.6 1.2 150 10.5 1.3 160 10.5 1.3 170 9.8 1.4 180 9.2 1.5 190 9.0 1.4 200 8.8 1.4 220 10.5 1.5 240 12.2 1.7 260 13.1 1.7 280 13.2 1.7 300 134 1.8 320 134 1.9 340 13.4 2.0 360 13.9 2.0 380 14.9 2.1 400 15.6 2.2 450 16.4 2.3 500 16.6 24 550 19.7 2.8 600 19.3 2.6 650 20.0 2.8 700 19.5 2.8 750 18.5 3.1 800 17.8 3.4 850 18.3 3.1 900 20.5 3.3 950 214 3.7 1000 21.2 3.7 LKOPS SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2606—2468 Page No. : 21 of 22

FCC TEST REPORT Report No. : F931001 8. List of Measuring Equipments Used Instrument Manufacturer Model No. Serial No. Characteristics |Calibration Date Remark EMC Receiver HP B591EM 3710A01187 9 KHz — 18 GHz Sep. 18, 1998 Conduction {site 2) LISN (EUT) Telemeter NNB—2/16Z 98009 _ 50 ohm / 50 uH Jan. 22, 1999 Conduction (site 2) LISN (Support Unit) EMCO 3810/2NM 9703—1839 50 ohm / 50 uH Jul. 06, 1998 Conduction (site 2) Quasi—peak Adapter HP 85650A 2521400821 9KHz —1 GHz Nov. 14, 1998 Radiation _(site 5) Spectrum Analyzer HP B568B 2634403000 100Hz — 1.5GHz Nov. 14, 1998 Radiation (Site 5) Amplifier (Site 5) HP B447D 2944408290 0.1MHz —1.3GHz Nov. 13, 1998 Radiation Bilog Antenna (Site 5) CHASE CBL6112A 2287 30MHz —2GHz Jan. 07, 1999 Radiation Half—wave dipole EMCO 31210 9705—1285 28 M — 1GHz May 19, 1998 Radiation antenna (Site 5) Turn Table (site 5) EMCO 2080 9711—2021 0 ~ 360 degree N/A Radiation Antenna Mast (site 5) EMCO 2075 9711—2115 1 m— 4 m N/A Radiation SPORTON International Inc. FCC ID : FSUGEPRO TEL : 886—2—2696—2468 Page No. : 22 of 22


Document Created: 2001-06-26 15:38:30
Document Modified: 2001-06-26 15:38:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC