Test Report

FCC ID: FK3JK-WR0TS-K

Test Report

Download: PDF

FCCID_4025444

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

FCC TEST REPORT

FOR
SIIG Inc
FK3-SIIG-K-JK-WR0TS
Test Model: JK-WR0S12-S1
List Model No.: JK-WR0T12-S1, JK-WR0S12-S1

Prepared for : SIIG Inc
Address : 6078 Stewart Avenue, Fremont, CA 94538-3152, USA

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd
1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an
Address :
District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : August 14, 2018
Number of tested samples : 2
Sample number : Prototype
Date of Test : August 14, 2018~ September 05, 2018
Date of Report : September 05, 2018

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

FCC -- TEST REPORT

September 05, 2018
Test Report No. : LCS180807076AEA
Date of issue

Test Model.............................. : JK-WR0S12-S1

EUT......................................... : FK3-SIIG-K-JK-WR0TS

Applicant............................... : SIIG Inc

Address.................................. : 6078 Stewart Avenue, Fremont, CA 94538-3152, USA
Telephone.......................... : /

Fax..................................... : /

Manufacturer..................... : Mosen Electronics Co., Ltd

Address.............................. : Rm.4B,Kingswell Comm Tower,171-173 Lockhart Rd,HongKong

Telephone.......................... : /

Fax..................................... : /

Factory.............................. : Mosen Electronics Co., Ltd

Address.............................. : Rm.4B,Kingswell Comm Tower,171-173 Lockhart Rd,HongKong

Telephone.......................... : /

Fax..................................... : /

Test Result Positive

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

Revision History

Revision Issue Date Revisions Revised By
000 September 05, 2018 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

TABLE OF CONTENTS

1. GENERAL INFORMATION ................................................................................................................ 6
1.1. Description of Device (EUT) ................................................................................................................ 6
1.2. Support Equipment List ........................................................................................................................ 6
1.3. External I/O ............................................................................................................................................. 6
1.4. Description of Test Facility ................................................................................................................... 6
1.5. Statement of the Measurement Uncertainty ...................................................................................... 7
1.6. Measurement Uncertainty .................................................................................................................... 7
1.7. Description of Test Modes.................................................................................................................... 7
1.8. Channel List and Frequency ................................................................................................................ 8
2. TEST METHODOLOGY ...................................................................................................................... 9
2.1 EUT Configuration ........................................................................................................................................ 9
2.2. EUT Exercise ............................................................................................................................................... 9
2.3. General Test Procedures ........................................................................................................................... 9
3. SYSTEM TEST CONFIGURATION ................................................................................................ 10
3.1. Justification ................................................................................................................................................ 10
3.2. EUT Exercise Software ............................................................................................................................ 10
3.3. Special Accessories .................................................................................................................................. 10
3.4. Block Diagram/Schematics ...................................................................................................................... 10
3.5. Equipment Modifications .......................................................................................................................... 10
3.6. Test Setup .................................................................................................................................................. 10
4. SUMMARY OF TEST RESULTS ..................................................................................................... 11
5. TEST RESULT .................................................................................................................................... 12
5.1. Radiated Emission Measurement ........................................................................................................... 12
5.2. AC Power Line Conducted Emissions (Not Applicable) ...................................................................... 21
5.3. Results for Band edge Testing ................................................................................................................ 22
5.4. 99% Occupied Bandwidth and 20 dB Bandwidth Measurement ....................................................... 25
5.5. ANTENNA REQUIREMENT .................................................................................................................... 27
6. LIST OF MEASURING EQUIPMENT ............................................................................................. 28
7. TEST SETUP PHOTOGRAPHS OF EUT ...................................................................................... 29
8. EXTERIOR PHOTOGRAPHS OF EUT .......................................................................................... 29
9. INTERIOR PHOTOGRAPHS OF EUT ............................................................................................ 29

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

1. GENERAL INFORMATION

1.1. Description of Device (EUT)

EUT : FK3-SIIG-K-JK-WR0TS
Model Number JK-WR0T12-S1, JK-WR0S12-S1
PCB board, structure and internal of these model(s) are the
Model Declaration
same, Only the model name is different for these models.
Test Model : JK-WR0S12-S1
Power Supply : DC 3.0V by2*AAA
Hardware version : XH-668
Software version : MA13861
2408-2474MHz(2408MHz, 2410MHz, 2412MHz, 2414MHz,
2416MHz, 2418MHz, 2420MHz, 2422MHz, 2424MHz, 2426MHz,
2.4G Operation frequency 2428MHz, 2430MHz, 2432MHz, 2434MHz, 2436MHz, 2438MHz,
:
2440MHz, 2442MHz, 2444MHz, 2446MHz, 2448MHz, 2450MHz,
2452MHz, 2454MHz, 2456MHz, 2458MHz, 2460MHz, 2462MHz,
2464MHz, 2466MHz, 2468MHz, 2470MHz, 2472MHz, 2474MHz)
Channel Number : 34 channel
Modulation Type : FSK
Antenna Description : Internal Antenna, 1.8dBi (Max).

1.2. Support Equipment List

Manufacturer Description Model Serial Number Certificate
-- -- -- -- --

1.3. External I/O

I/O Port Description Quantity Cable
-- -- --

1.4. Description of Test Facility

FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0.

The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR
16-1-4:2010 SVSWR requirement for radiated emission above 1GHz.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

1.5. Statement of the Measurement Uncertainty

The data and results referenced in this document are true and accurate. The reader is cautioned that
there may be errors within the calibration limits of the equipment and facilities. The measurement
uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4
“Specification for radio disturbance and immunity measuring apparatus and methods – Part 4:
Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN
ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may
result in additional deviation. The manufacturer has the sole responsibility of continued compliance of
the device.

1.6. Measurement Uncertainty

Test Item Frequency Range Uncertainty Note
9KHz~30MHz ±3.10dB (1)
30MHz~200MHz ±2.96dB (1)
Radiation Uncertainty : 200MHz~1000MHz ±3.10dB (1)
1GHz~26.5GHz ±3.80dB (1)
26.5GHz~40GHz ±3.90dB (1)
Conduction Uncertainty : 150kHz~30MHz ±1.63dB (1)
Power disturbance : 30MHz~300MHz ±1.60dB (1)
(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2.

1.7. Description of Test Modes

The EUT operates in the unlicensed ISM band at 2.4GHz. The following operating modes were
applied for the related test items.

All test modes were tested, only the result of the worst case was recorded in the report.

It was pre-tested on the positioned of each 3 axis. The worst case was found positioned on X-plane.

Mode of Operations Transmitting Frequency (MHz)
2408
FSK 2440
2474
For Conducted Emission
Test Mode TX Mode
For Radiated Emission
Test Mode TX Mode

Worst-case mode and channel used for 9 KHz-1000 MHz radiated emissions was the mode and
channel with the highest output power, that was determined to be TX-2408MHz.

***Note: Using a temporary antenna connector for the EUT when the conducted measurements are
performed.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

1.8. Channel List and Frequency

Channel Frequency (MHz) Channel Frequency (MHz)
1 2408 17 2440
2 2410 -- --
3 2412 -- --
4 2414 -- --
-- -- 33 2472
-- -- 34 2474

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

2. TEST METHODOLOGY

All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and
conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd.

2.1 EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions
requirement and operating in a manner that intends to maximize its emission characteristics in a
continuous normal application.

2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the
measurements.
According to its specifications, the EUT must comply with the requirements of the Section 15.203, 15.205,
15.207, 15.209 and 15.249 under the FCC Rules Part 15 Subpart C.

2.3. General Test Procedures

2.3.1 Conducted Emissions
According to the requirements in Section 6.2 of ANSI C63.10: 2013, AC power-line conducted emissions
shall be measured in the frequency range between 0.15 MHz and 30MHz using Quasi-peak and average
detector modes.

2.3.2 Radiated Emissions
The EUT is placed on a turn table and the turntable shall rotate 360 degrees to determine the position of
maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to
find out the highest emission. And also, each emission was to be maximized by changing the polarization
of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory
radiated emission measurements were made according to the requirements in Section 6.3 of ANSI C63.10:
2013.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

3. SYSTEM TEST CONFIGURATION

3.1. Justification
The system was configured for testing in a continuous transmit condition.

3.2. EUT Exercise Software
The system was configured for testing in a continuous transmit condition.
Using 1 samples to test, Power on while holding down the ESC+Y keys for 5 seconds after release into
test mode, then click the Tab key to set up transmitter highest channel, middle channel, lowest channel
and hopping frequency mode

3.3. Special Accessories
N/A

3.4. Block Diagram/Schematics
Please refer to the related document

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

4. SUMMARY OF TEST RESULTS

Applied Standard: FCC Part 15 Subpart C;
FCC Rules Description of Test Result
§15.203 Antenna Requirements Compliant
§15.207(a) Power Line Conducted Emissions N/A*
§15.205(a), §15.209(a),
Radiated Emissions Measurement Compliant
§15.249(a), §15.249(c)
§15.205, §15.249(d) Band Edges Measurement Compliant
§15.249, §15.215 99% and 20 dB Bandwidth Compliant

Remark:
N/A* - Not Applicable!!!

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

5.1.3. Test Procedures

1) Sequence of testing 9 kHz to 30 MHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions

Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin
to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit
will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

2) Sequence of testing 30 MHz to 1 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in
peak to find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the
graph of the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

3) Sequence of testing 1 GHz to 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to
find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter. This procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position,
antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with
the graph of the premeasurement with marked maximum final measurements and the limit will be
stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

4) Sequence of testing above 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.

Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.

Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and
limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

5.1.8. Results for Radiated Emissions (1 – 18 GHz)

Field Strength of Fundamental (TX-2408MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2408 H 79.63 60.46 114 94 Pass
2408 V 63.25 50.42 114 94 Pass

Reading Ant. Pre. Cab.
Freq. Measured Limit Margin
Level Fac. Fac. Loss Remark Pol.
MHz dBuV/m dBuV/m dB
dBuV dB/m dB dB
4816.00 58.80 32.14 34.12 3.53 60.35 74.00 -13.65 Peak Horizontal
4816.00 41.96 32.14 34.12 3.53 43.51 54.00 -10.49 Average Horizontal
4816.00 54.06 32.17 34.15 3.55 55.63 74.00 -18.37 Peak Vertical
4816.00 39.50 32.17 34.15 3.55 41.07 54.00 -12.93 Average Vertical

Field Strength of Fundamental (TX-2440MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2440 H 78.99 69.34 114 94 Pass
2440 V 69.25 59.75 114 94 Pass

Reading Ant. Pre. Cab.
Freq. Measured Limit Margin
Level Fac. Fac. Loss Remark Pol.
MHz dBuV/m dBuV/m dB
dBuV dB/m dB dB
4880.00 61.97 33.06 35.04 3.94 63.93 74.00 -10.07 Peak Horizontal
4880.00 39.36 33.06 35.04 3.94 41.32 54.00 -12.68 Average Horizontal
4880.00 55.38 33.16 35.15 3.96 57.35 74.00 -16.65 Peak Vertical
4880.00 41.03 33.16 35.15 3.96 43.00 54.00 -11.00 Average Vertical

Field Strength of Fundamental (TX-2474MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2474 H 79.37 61.52 114 94 Pass
2474 V 80.16 61.23 114 94 Pass

Reading Ant. Pre. Cab.
Freq. Measured Limit Margin
Level Fac. Fac. Loss Remark Pol.
MHz dBuV/m dBuV/m dB
dBuV dB/m dB dB
4948.00 52.52 33.26 35.14 3.98 54.62 74.00 -19.38 Peak Horizontal
4948.00 44.42 33.26 35.14 3.98 46.52 54.00 -7.48 Average Horizontal
4948.00 54.43 33.36 35.16 4.00 56.63 74.00 -17.37 Peak Vertical
4948.00 37.58 33.36 35.16 4.00 39.78 54.00 -14.22 Average Vertical

Notes:
1. Measuring frequencies from 9 KHz~10th harmonic (ex. 26GHz), No emission found between lowest
internal used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9 KHz~10th harmonic (ex. 26GHz) were made
with an instrument using Peak detector mode.
3. No emission was be recorded above 18GHz means the reading of emissions are attenuated more than
20dB below the permissible limits or the field strength is too small to be measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

9. For devices with multiple antenna-ports, measure the power of each individual chain and sum the
EIRP of all chains in linear terms (e.g., Watts, mW).
10. Compare the resultant electric field strength level to the applicable regulatory limit.
11. Perform radiated spurious emission test duress until all measured frequencies were complete.

5.3.5. Measuring Instruments and Setting

GFSK
Ground Covert
Conducted Antenna
Frequency Reflection Radiated E Limit
Power Gain Detector Verdict
(MHz) Factor Level At 3m (dBuV/m)
(dBm) (dBi)
(dB) (dBuV/m)
2310.000 -59.011 2.000 0.000 38.217 Peak 74.00 PASS
2310.000 -71.630 2.000 0.000 25.598 Average 54.00 PASS
2384.000 -42.413 2.000 0.000 54.815 Peak 74.00 PASS
2384.1000 -48.300 2.000 0.000 48.928 Average 54.00 PASS
2390.000 -47.186 2.000 0.000 50.042 Peak 74.00 PASS
2390.000 -57.760 2.000 0.000 39.468 Average 54.00 PASS
2483.500 -46.201 2.000 0.000 51.027 Peak 74.00 PASS
2483.500 -67.990 2.000 0.000 29.238 Average 54.00 PASS
2486.028 -36.010 2.000 0.000 61.218 Peak 74.00 PASS
4286.000 -57.210 2.000 0.000 40.018 Average 54.00 PASS
2500.000 -57.944 2.000 0.000 39.284 Peak 74.00 PASS
2500.000 -70.640 2.000 0.000 26.588 Average 54.00 PASS

Remark:

1. The other emission levels were very low against the limit.
2. The average measurement was not performed when the peak measured data under the limit of
average detection.
3. Detector AV is setting spectrum/receiver. RBW=1MHz/VBW=10Hz/Sweep time=Auto/Detector=Peak;
4. Since the out-of-band characteristics of the EUT transmit antenna will often be unknown, the use of a
conservative antenna gain value is necessary. Thus, when determining the EIRP based on the
measured conducted power, the upper bound on antenna gain for a device with a single RF output
shall be selected as the maximum in-band gain of the antenna across all operating bands, or 2 dBi,
whichever is greater. However, for devices that operate in multiple frequency bands while using the
same transmit antenna, the highest gain of the antenna within the operating band nearest in frequency
to the restricted band emission being measured may be used in lieu of the overall highest gain when
the emission is at a frequency that is within 20 percent of the nearest band edge frequency, but in no
case shall a value less than 2 dBi be used.
5. Please refer to following test plots;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 23 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: FK3JK-WR0TS-K Report No.:LCS180807076AEA

7. TEST SETUP PHOTOGRAPHS OF EUT

Please refer to separated files for Test Setup Photos of the EUT.

8. EXTERIOR PHOTOGRAPHS OF EUT

Please refer to separated files for External Photos of the EUT.

9. INTERIOR PHOTOGRAPHS OF EUT

Please refer to separated files for Internal Photos of the EUT.

----------------THE END OF TEST REPORT---------------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 29

Document Created: 2018-09-30 17:40:05
Document Modified: 2018-09-30 17:40:05

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC