WITH SETUP PHOTOS

FCC ID: FI7PEIH00

Test Report

Download: PDF
FCCID_95745

Product : HomePNA 10Mbps PCI Card Manufacture : Archtek Telecom Corporation FCC ID : FI7PEIH00 Model : HPE-110 Report No. : MLT0003P15002 Test Date : April 09.2000 Test By Max Light Technology Co.,Ltd. Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan., R.O.C. Tel: 886-2-2363-2447 Fax: 886-2-2363-2597 The test report consists of 21 pages in total. It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of our laboratory.

MAX LIGHT MEASUREMENT REPORT Page: 2/21 Technology Lab Table of Contents : I. General 4. II. Conducted Emissions Requirements 9. III. Radiated Emissions Requirements 13. Appendix I (EUT Test Setup) 18. Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 3/21 Technology Lab CERTIFICATION We here by verify that : The test data, data evaluation, test procedures and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4-1992. All test were conducted by MLT(Max Light Technology Co.,Ltd) Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan, R.O.C Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with Class B radiated and conducted emission limit of FCC Rules Part 15 Subpart B. EUT : HomePNA 10Mbps PCI Card Applicant : Archtek Telecom Corporation . 10F,No.110,Sec.3,Chung-Shan Rd., Chung-Ho,Taipei,Taiwan,R.O.C Manufacturer : Archtek Telecom Corporation . 4F. No.9, Lane 130, Min-Chyuan Rd., Hsin-Tien , Taipei ,Taiwan Model No : HPE-110 FCC ID : FI7PEIH00 Prepared by : Approved by : Country Huang Roger Chen Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 4/21 Technology Lab I. GENERAL 1.1 Introduction The following measurement report is submitted on behalf of Archtek Telecom Corporation. In support of a Class B Digital Device certification in accordance with Part2 Subpart J and Part 15 Subpart A And B of the Commission’s and Regulations. 1.2 Description of EUT EUT : HomePNA 10Mbps PCI Card Applicant : Archtek Telecom Corporation . 10F,No.110,Sec.3,Chung-Shan Rd., Chung-Ho,Taipei,Taiwan,R.O.C Manufacturer : Archtek Telecom Corporation . 4F. No.9, Lane 130, Min-Chyuan Rd., Hsin-Tien , Taipei ,Taiwan Model No : HPE-110 FCC ID : FI7PEIH00 Power Type : Powered by PC Phone Cable : RJ-11Cx2(Nonshielded, 7’ long ,Plastic hoods) During testing the EUT was operated at Tx or Rx mode for each emission measured(P.S Run “Ping (IP Address) –T –L 1000” comment in Dos Mode). This was done in order to ensure that maximum emission levels were attained. Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 5/21 Technology Lab 1.3 Description of Support Equipment In order to construct the minimum system which required by the ANSI C63.4-1991, following equipments were used as the support units. Computer : COMPAQ Model No. : 3284 Serial No. : L708BKTB4154 FCC ID : EJH3284 Keyboard : COMPAQ Model No. : KPQ-E99ZC-13 Serial No. : 237743-334 FCC ID : CMYKPQ7285 Monitor : COMPAQ Model No. : 303U Serial No. : 704AG19TG099 FCC ID : BJMCM14UH Mouse : COMPAQ Model No. : 196694-301 Serial No. : 1SH67CHE03360 FCC ID : EMJMUSJJ Printer : PANASONIC Model No. : KX-P1080I Serial No. : 7CKAKE98933 FCC ID : ACJ5Z6KX-P10801 Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 6/21 Technology Lab Telephone : GE Model No. : 2-9240A Serial No. : 1943K Modem : Askey (External Fax / Data Modem) Model No. : WS1414VE Serial No. : IAH-10811 FCC ID : H8N1414VE Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 7/21 Technology Lab 1.4 Configuration of System Under Test To another Home Lan Card Power Supply RS-232 RS-232 Printer Monitor Telephone Modem PC EUT Keyboard Mouse During testing the EUT(HomePNA 10Mbps PCI Card) install in the Compaq PC. So there is no need for additional I/O card. A mouse was connected to the mouse port and a printer was connected to the parallel port. There is one serial port. A external modem connected the serial port and the external modem connected with two unterminated telephone cables on the line and phone jack. A telephone set was connected to the Phone Jack of EUT and the Line Jack of EUT was connected to another Home Lan Card. Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 8/21 Technology Lab 1.5 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI C63.4-1992 "Measurement of unIntentional Radiators." 1.6 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment's emission characteristics. The final configuration of the test system and the mode of operation used during these tests was chosen as that which produced the highest emission levels. However, only those conditions which the EUT was considered likely to encounter in normal use were investigated. The system's radiated and conducted emissions were investigated while the computer alternately transferred data to the EUT (1000 bytes). Run “Ping (IP Address -T –L 1000)” comment which sent a continuous stream of 1000 Bytes data to EUT and transferred data to and from the EUT was proven to worst case emissions. The system's physical layout and cabling was randomly arranged to ensure that maximum emission levels were attained. Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 9/21 Technology Lab II. Conducted Emissions Requirements 2.1 General & Setup : The power line conducted emission measurements were performed in a shielded enclosure. The EUT was assembled on a wooden table which is 80 centimeters high, was placed 40 centimeters from the backwall and at least 1 meter from the sidewall. Power was fed to the EUT from the public utility power grid through a line filter and EMCO Model 3825/2 Line Impedance Stabilization Networks (LISN). The LISN housing, measuring instrumentation case, ground plane, etc., were electrically bonded together at the same RF potential. The Spectrum analyzer was connected to the AC line through an isolation transformer. The 50-ohm output of the LISN was connected to the spectrum analyzer directly. Conducted emission levels were in the CISPER quasi-peak detection mode. The analyzer's 6 dB bandwidth was set to 9 KHz. No post-detector video filter was used. The spectrum was scanned from 450 KHz to 30 MHz. The physical arrangement of the test system and associated cabling was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit's emanations in amplitude and frequency. All spurious emission frequencies were observed. The highest emission amplitudes relative to the appropriate limit were measured and have been recorded in paragraph 2.6. 2.2 Test Equipment List: A. EMCO 3825/2 LISN (S/N:2654) B. EMCO 3825/2 LISN (S/N:2658) C. HP 8591EM 9KHZ-1.8GHz Spectrum Analyzer (S/N:73412A00110) D. Shielded Room (MLT-SR1) Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 10/21 Technology Lab 2.3 Test Configuration: Front View of The Test Configuration Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 11/21 Technology Lab Rear View of The Test Configuration Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 12/21 Technology Lab 2.4 Test condition: EUT tested in accordance with the specifications given by the manufacturer , and exercised in the most unfavorable manner. 2.5 Conducted Emissions Limits: Frequency range (MHz) Limits (dBuV) 0.45 to 30 47.9 Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 13/21 Technology Lab 2.6 Measurement Data Of Conducted Emissions: The following table show a summary of the highest emissions of power line conducted emissions to the HOT and NATURAL conductor of the EUT power. Manufacturer : Archtek Telecom Corporation. Model No : HPE-110 EUT : HomePNA 10Mbps PCI Card Power Line Conducted Emissions (Class B) Conductor Frequency Peak Amplitude Limits (MHz) (dBuV) (dBuV) 0.45 32.76 47.9 7.32 38.19 47.9 12.64 35.63 47.9 L1 17.93 38.17 47.9 21.76 37.35 47.9 26.84 36.83 47.9 30.00 37.16 47.9 0.45 33.16 47.9 7.32 37.86 47.9 12.64 36.42 47.9 L2 17.93 37.86 47.9 21.76 39.18 47.9 26.84 37.32 47.9 30.00 38.45 47.9 Notes : 1.L1: One end & Ground L2: The other end & Ground 2.Height of table on which the EUT was placed : 0.8 m. 3.The above test results are obtained under the normal condition. Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 14/21 Technology Lab III. Radiated Emissions Requirements 3.1 General & Setup : Prior to open-field testing, the EUT was placed in a shielded enclosure and scanned at a close distance to determine its emission characteristics. The physical arrangement of the EUT was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit's emanations in amplitude, directivity, and frequency. The exact system configuration which produced the highest emissions was noted so it could be reproduced later during the open-field tests. This was done to ensure that the final measurements would demonstrate the worst-case interference potential of the EUT. Final radiation measurements were made on a three-meter, open-field test site. The EUT system was placed on a nonconductive turntable which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 30 MHz to 1000 MHz using an Hewlett Packard 8591EM Spectrum Analyzer, EMCO Biconical Antenna (Model 3142) for 30-1000MHz. At each frequency, the EUT was rotated 360 degrees, and the antenna was raised and lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post-detector video filters were used in the test. The spectrum analyzer's 6 dB bandwidth was set to 120 KHz, and the analyzer was operated in the quasi-peak detection mode. The highest emission amplitudes relative to the appropriate limit were measured and recorded in paragraph 3.6. 3.2 Test Equipment List: A. HP 8591EM 9KHz-1.8GHz Spectrum Analyzer (S/N:73412A00230) B. HP 8447D Pre Amplifier (S/N:2944A08954) C. EMCO 3142 Biconilog Antenna (S/N:1184) D. HP 8590A 10KHz-1.5GHz Spectrum Analyzer (S/N:5212A000211) Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 15/21 Technology Lab 3.3 Test Configuration: Front View of The Test Configuration Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 16/21 Technology Lab Rear View of The Test Configuration Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 17/21 Technology Lab 3.4 Test condition: EUT tested in accordance with the specifications given by the manufacturer , and exercised in the most unfavorable manner. 3.5 Radiated Emissions Limits: Frequency range (MHz) Peak(dBuV) 30 to 88 40 88 to 216 43.5 216 to 960 46 Above 960 54 Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 18/21 Technology Lab 3.6 Measurement Data Of Radiated Emissions: 3.6.1 Open Field Radiated Emissions (HORIZONTAL) The highest peak values of radiated emissions from the EUT at various antenna heights, antenna polarization, EUT orientation , etc. are recorded on the following Manufacturer : Archtek Telecom Corporation. Model No : HPE-110 EUT : HomePNA 10Mbps PCI Card Radiated Emissions (HORIZONTAL) Frequency Amplitude Ant. Table Limits(Class B) Margin (MHz) (dBuV/m) (m) (Degree) (dBuV/m) (dB) 116.97 31.09 1.5 360 43.5 -12.41 128.02 35.43 1 200 43.5 -8.07 187.25 32.76 2 250 43.5 -10.74 192.05 36.12 1.5 360 43.5 -7.38 224.00 35.37 1 300 46 -10.63 255.88 36.87 1.5 200 46 -9.13 288.00 38.51 2 240 46 -7.49 352.26 40.76 2 360 46 -5.24 416.01 41.76 1 300 46 -4.24 448.30 40.98 1.5 270 46 -5.02 480.33 39.17 2 360 46 -6.83 Notes : 1.Margin= Amplitude - Limits 2.Distance of Measurement : 3 Meter (30-1000MHz) 3.Height of table for EUT placed: 0.8 Meter. 4.ANT= Antenna height. 5.Amplitude= Reading Amplitude –Amplifier gain+Cable loss +Antenna factor (Auto calculate in spectrum analyzer) Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 19/21 Technology Lab 3.6.2 Open Field Radiated Emissions (VERTICAL) The highest peak values of radiated emissions from the EUT at various antenna heights, antenna polarization, EUT orientation , etc. are recorded on the following. Manufacturer : Archtek Telecom Corporation. Model No : HPE-110 EUT : HomePNA 10Mbps PCI Card Radiated Emissions (VERTICAL) Frequency Amplitude Ant. Table Limits(Class B) Margin (MHz) (dBuV/m) (m) (Degree) (dBuV/m) (dB) 116.97 33.45 1 270 43.5 -10.05 128.02 38.62 1.5 300 43.5 -4.88 187.25 34.87 1.5 360 43.5 -8.63 192.05 37.75 1 200 43.5 -5.75 224.00 36.49 1.5 340 46 -9.51 255.88 35.26 1 300 46 -10.74 288.00 39.70 2 360 46 -6.30 352.26 42.01 1.5 270 46 -3.99 416.01 41.55 1 200 46 -4.45 448.30 41.63 1.5 360 46 -4.37 480.33 40.91 1 360 46 -5.09 Notes : 1.Margin= Amplitude - Limits 2.Distance of Measurement : 3 Meter (30-1000MHz) 3.Height of table for EUT placed: 0.8 Meter. 4.ANT= Antenna height. 5.Amplitude= Reading Amplitude –Amplifier gain+Cable loss +Antenna factor (Auto calculate in spectrum analyzer) Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 20/21 Technology Lab Appendix I- EUT Test SETUP MEASUREMENT OF POWER LINE CONDUCTED RFI VOLTAGE EUT 0.8M 0.8M LISN Metal floor surfaced with 30mm of insulating material Report Number: MLT0003P15002 FCC ID: FI7PEIH00

MAX LIGHT MEASUREMENT REPORT Page: 21/21 Technology Lab Appendix I- EUT Test SETUP MEASUREMENT OF RADIATED EMISSION Antenna Tower 4.0M 3.0M Receiver Antenna EUT 0.8M Ground Plane 0000 RF Test Receiver Report Number: MLT0003P15002 FCC ID: FI7PEIH00


Document Created: 2019-10-28 06:14:52
Document Modified: 2019-10-28 06:14:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC