RF Exposure Report

FCC ID: EO9OW3

RF Exposure Info

Download: PDF
FCCID_4066254

MAXIMUM PERMISSIBLE EXPOSURE REPORT (Measurement) FOR THE Device: CGR ACT Module 3 (CAM3) Model: OW3 Report No.: 101674-5 Date of issue: October 11, 2018 PREPARED FOR: Itron, Inc. 2111 N. Molter Road Liberty Lake, WA 99019 The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc.

Table of Contents Test Report Information ............................................................................................................................... 3 Purpose ......................................................................................................................................................... 3 Device and Antenna Operating Configuration .............................................................................................. 3 Test Procedure .............................................................................................................................................. 3 Other Considerations .................................................................................................................................... 3 Equipment Under Test .................................................................................................................................. 4 Data ............................................................................................................................................................... 5 Summary ..................................................................................................................................................... 10 APPENDIX A - Assessment Procedure ......................................................................................................... 11 APPENDIX B - RF Exposure Limits................................................................................................................ 14 APPENDIX C - References ............................................................................................................................ 19 Page 2 of 19 Report No: 101674-5

Test Report Information Test Location(s): Report Prepared By: CKC Laboratory, Inc. Don Nguyen & Terri Rayle 110 North Olinda Place CKC Laboratories, Inc. Brea, CA 92823 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Jay Holcomb Date of Equipment Receipt: Sept 12, 2018 Customer Reference Number: 159196 Date(s) of Testing: September 14, 2018 Project Number: 101674 Purpose: To demonstrate compliance with United States, Canada, Australia and/or European Union RF Exposure requirements for Mobile Equipment (devices used >20cm from the body), where MPE measurements apply. Device and Antenna Operating Configuration: Device operating at maximum output power with continuous transmission of modulated data. Test Procedure: This equipment is evaluated in accordance with the guidelines set forth in KDB 447498 & ANSI C95.1 for the US, Health Canada Safety Code 6 & RSS 102 for Canada, ARPANSA RPS3 for AU and EN 62479 or EN 62311 for EU. Other Considerations: Report considers stand-alone configuration only. RF Exposure limits are calculated at the mid-point of each operating band. Multi-transmitter devices are assumed to permit simultaneous transmission, unless indicated otherwise. Simultaneous transmissions aggregated providing a worst case assessment. Page 3 of 19 Report No: 101674-5

EQUIPMENT UNDER TEST (EUT) During testing, numerous configurations may have been utilized. The configurations listed below support compliance to the standard(s) listed in the Summary of Results section. Configuration 5 Equipment Tested: Device Manufacturer Model # S/N CGR ACT Module 3 (CAM3) Itron, Inc. OW3 FCC-2 (CGR) CAM3-FCC2 (CAM Module, ID) Support Equipment: Device Manufacturer Model # S/N Connected Grid Router Cisco Systems, Inc. CGR 1240 FTX2204G01J (Host Laptop Dell E6420 NA AC Adapter (for Laptop) Dell DA130PE1-00 NA USB to Ethernet adapter Linksys USB3GIGV1 NA 2.8dBi Colinear Omni Cisco Systems, Inc. 07-1140-02 NA Antenna (attached) Configuration 6 Equipment Tested: Device Manufacturer Model # S/N CGR ACT Module 3 (CAM3) Itron, Inc. OW3 FCC-2 (CGR) CAM3-FCC2 (CAM Module, ID) Support Equipment: Device Manufacturer Model # S/N Connected Grid Router (Host Cisco Systems, Inc. CGR 1240 FTX2204G01J Laptop Dell E6420 NA AC Adapter (for Laptop) Dell DA130PE1-00 NA USB to Ethernet adapter Linksys USB3GIGV1 NA 5.5dBi Colinear Omni Antenna Cisco Systems, Inc. ANT-WPAN-OM- NA (remote) OUT-N Configuration 7 Equipment Tested: Device Manufacturer Model # S/N CGR ACT Module 3 (CAM3) Itron, Inc. OW3 FCC-2 (CGR) CAM3-FCC2 (CAM Module, ID) Support Equipment: Device Manufacturer Model # S/N Connected Grid Router (Host Cisco Systems, Inc. CGR 1240 FTX2204G01J Laptop Dell E6420 NA AC Adapter (for Laptop) Dell DA130PE1-00 NA USB to Ethernet adapter Linksys USB3GIGV1 NA 8.15dBi Colinear Omni Antenna Antenex FG9026 NA (remote) 3dB Attenuator (for 8.15dBi antenna) Mini-Circuits BW-N3W5+ NA Page 4 of 19 Report No: 101674-5

DATA Test Setup/Conditions Test Location: Brea, Chamber C Test Engineer: Don Nguyen Configuration: 5, 6, and 7 Test Date(s): 9/14/2018 Test Equipment Asset Description Manufacturer Model Cal Date Cal Due 02043 Field Probe Amplifier Research FP2080 5/5/2017 5/5/2019 00636 Field Monitor Amplifier Research FM2000 11/2/2017 11/2/2019 MPE Measurements Operational Details Power Reported is: ☒ Peak ☐ Average Limit Used is: ☒ General Population ☐ Occupational Exposure Operating Band MHz Power Ant Gain EIRP TX Antenna Configuration dBm dBi dBm Simultaneous 902.2 to 927.75 29.5 2.8 32.30 Yes External 902.2 to 927.75 29.5 5.5 35.00 Yes External 902.2 to 927.75 29.5 8.15 - 3dB 34.65 Yes External attenuator Note: EUT contains modem and Wi-Fi modules transmitting simultaneously at maximum power. MPE Measurements for Static Fields (Free Space Configuration) For equipment where the fields are invariant in time, measurements are performed at a fixed height between 1.0m to 1.8m representing worst case measurements as determined by preliminary assessment. FCC Part 2.1091 Distance Height Measured Measured Measured Exposure Limit Result (m) (m) Exposure Exposure mW/cm2 (worst case) mW/cm2 mW/cm2 8.15 dBi antenna- mW/cm2 2.8 dBi antenna 5.5 dBi antenna 3dB attenuator 0.2 1.0 0.1082 0.0119 0.0077 0.56 Pass 0.2 1.4 0.0192 0.0112 0.0220 0.56 Pass 0.2 1.8 0.0061 0.0021 0.0024 0.56 Pass 0.3 1.0 0.0565 0.0099 0.0061 0.56 Pass 0.3 1.4 0.0126 0.0116 0.0210 0.56 Pass 0.3 1.8 0.0056 0.0014 0.0021 0.56 Pass 0.4 1.0 0.0327 0.0089 0.0042 0.56 Pass 0.4 1.4 0.0095 0.0102 0.0174 0.56 Pass 0.4 1.8 0.0054 0.0010 0.0019 0.56 Pass Note: ISM, modem and Wi-Fi modules transmit simultaneously at highest power. Limits based on Operating Frequency Transmitter Highest power operating frequency range (MHz) Limit: (mW/cm2) ISM 902.4-927.6 0.61 Cellular Modem 824.0-849.0 0.56 Wi-Fi 2412-2462 1.50 Page 5 of 19 Report No: 101674-5

RSS-102, Issue 5 Distance Height Measured Measured Measured Exposure Limit Result (m) (m) Exposure Exposure W/m2 (worst case) 2 2 W/m W/m 8.15 dBi antenna- W/m2 2.8 dBi antenna 5.5 dBi antenna 3dB attenuator 0.2 1.0 1.0823 0.1191 0.0773 2.6 Pass 0.2 1.4 0.1916 0.1121 0.2197 2.6 Pass 0.2 1.8 0.0611 0.0208 0.0239 2.6 Pass 0.3 1.0 0.5654 0.0987 0.0611 2.6 Pass 0.3 1.4 0.1263 0.1155 0.2101 2.6 Pass 0.3 1.8 0.0561 0.0140 0.0208 2.6 Pass 0.4 1.0 0.3268 0.0892 0.0424 2.6 Pass 0.4 1.4 0.0955 0.1020 0.1740 2.6 Pass 0.4 1.8 0.0537 0.0096 0.0193 2.6 Pass Note: ISM, modem and Wi-Fi modules transmit simultaneously at highest power. Limits based on Operating Frequency Transmitter Highest power operating frequency range (MHz) Limit: (W/m2) ISM 902.4-927.6 2.77 Cellular Modem 824.0-849.0 2.60 Wi-Fi 2412-2462 5.40 ISO/IEC 17025 Decision Rule The declaration of pass or fail herein is based upon assessment to the specification(s) listed above, including where applicable, assessment of measurement uncertainties. For performance related tests, equipment was monitored for specified criteria identified in that section of testing. Page 6 of 19 Report No: 101674-5

Test Setup Photos 2.8dbi 2.8dbi Page 7 of 19 Report No: 101674-5

5.5dbi 5.5dbi Page 8 of 19 Report No: 101674-5

8.15dbi 8.15dbi Page 9 of 19 Report No: 101674-5

Summary MPE Measurement Results: Equipment demonstrating compliance with MPE measurement have been evaluated for use under mobile RF exposure configurations as identified herein. Additional configurations including collocation or simultaneous transmission with other transmitters (including necessary separation distances) are subject to further assessment. It is assumed that the manufacturer shall design the equipment such that the minimum separation distance of 20cm (or greater, as listed above) is met or that the manufacturer provides a protection guide (e.g. installation instructions) to the end user such that the antenna(s) may be installed in accordance with the manufacturer’s instructions in such a manor to maintain the minimum separation distance. General Comments: The absorption and distribution of Electromagnetic energy in the body is a very complex phenomena that depends on the mass, shape and physiological condition of the body; the orientation of the body with respect to the fields; and, the electrical properties of the body and the environment. Variables that may play a substantial role in possible biological effects are those that characterize the environment (including but not limited to: ambient temperature, air velocity, relative humidity and body insulation); and those that characterize the individual (including but not limited to: age, gender, activity level and existing debilitation or disease). Because innumerable factors may interact to determine specific biological effects of exposure to electromagnetic fields, any protection guide should consider both intended and unintended operational environments and provide guidance for installation and use of the product such that proper separation distances can be maintained. (ANSI C95.1) Page 10 of 19 Report No: 101674-5

APPENDIX A - Assessment Procedure TEST CONFIGURATION The EUT antenna is placed in a configuration typical of normal installation. Where antenna mounting is required, non-conductive materials are used for support structures. In the special case of magnetically mounted vehicle antennas, a reference ground plane is used to simulate actual installation. In order to limit external interference effects, the test is performed in a semi-anechoic chamber. The EUT equipment is setup in a configuration representative of normal use. Support equipment for the measurement instruments are located outside of the testing area. TEST PROCEDURE Measurements are performed using a broadband detector with three orthogonal measurement axes. Values recorded are RMS based on the maximum measurements. To determine the direction of the maximum measurement, the detector is moved throughout the RF field generated by the transmit antenna. The detector is positioned at a minimum of 12 radials and at varying distances from the antenna along each radial. The area of maximum RF energy determined during preliminary investigation shall be used for the remainder of the tests. In the case where a transmitter may have multiple frequency bands, the preliminary investigation shall be repeated for each band. For time varying fields, the appropriate averaging time is used. For spatially uniform fields, the measurement height is selected based on maximum preliminary measurements. For spatially non-uniform fields (e.g. distances close to a magnetically mounted vehicle antenna), spatial averaging may be performed. The method for performing spatially averaged measurements is as follows: 1. Determine the direction of the maximum measurement. 2. At a specific distance measure vertically from the floor 5 points comprising a linear cross section of an adult human body, beginning at 0.2m and at each 40cm up to 1.8m. 3. Calculate the average of the measurements and compare with the established limit. Since the applicable limits exist in several different measurement units, the following outlines the most common calculations used for determining the spatially averaged field. Case 1: Where limits are applied in electric field strength (V/m), the spatially averaged electric field strength along a grid of n points is calculated using: 1 1 n 2 E    Ei2   n i 1  Case 2: Where limits are applied in units of power density (mW/cm2), assuming measurements are made in the far field, where the E and H vectors are mutually orthogonal, power density is first calculated using: E2 S 3770 And the spatially averaged power density along a grid of n points is calculated using: 1 n S  Si n i 1 Page 11 of 19 Report No: 101674-5

The following diagram is an example of the grid used to perform local measurements for RF exposure evaluation over a whole-body spatial average. 1 The following diagram is an example of the setup used for most tests, excluding magnetically mounted vehicle antennas. 1 Source: IC GL-01 Page 12 of 19 Report No: 101674-5

The following diagram is an example of the setup used for vehicle-mounted antennas. In the case where vehicle glass mounted antennas are used, this setup shall not apply. The letter X represents the test distance used for RF exposure measurements. The distance X is measured from the phase center of the transmitting antenna to the volumetric center of the measurement instrument. In order to more accurately simulate normal installation, the antenna ground plane is not bonded to the ground reference plane. The transmitting antenna is placed in the center of the antenna ground plane. Page 13 of 19 Report No: 101674-5

APPENDIX B - RF Exposure Limits United States Compliance Requirements (1.1310): RF Exposure Evaluation Limits Occupational / Controlled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (minutes) 0.3-3.0 614 1.63 *(100) 6 3.0-30 1842/f 4.89/f *(900/f2) 6 30-300 61.4 0.163 1 6 300-1500 --- --- f/300 6 1500-100,000 --- --- 5.0 6 RF Exposure Evaluation Limits General Population / Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1500 --- --- f/1500 30 1500-100,000 --- --- 1.0 30 * Plane wave equivalent power density Limit is calculated based on the mid-band frequency used in the operating frequency range. Stand-Alone Evaluation Exemption Levels: In accordance with KDB 447498 D01 v05r02 Max Output Power at Exemption Limit (mW) Frequency d ≤ 50mm 50mm < d ≤ 20cm (MHz) 1 𝑅 ∙ 50 100 𝑅 ∙ 50 100 100 <100 ∙( ) ∙ (1 + 𝐿𝑂𝐺 ( )) ( + (𝑑 − 50) ) ∙ (1 + 𝐿𝑂𝐺 ( )) 2 √0.1 𝑓𝑀𝐻𝑧 √0.1 150 𝑓𝑀𝐻𝑧 𝑅 ∙ 50 𝑓𝑀𝐻𝑧 100-1500 ( + (𝑑 − 50) ) 𝑅∙𝑑 √𝑓𝐺𝐻𝑧 150 ( ) √𝑓𝐺𝐻𝑧 𝑅 ∙ 50 1500-6000 ( + (𝑑 − 50) ∙ 10) √𝑓𝐺𝐻𝑧 R is the allowed ratio: 3 for 1-g SAR and 7.5 for 10-g extremity SAR. d is distance in mm, rounded to the nearest mm. Page 14 of 19 Report No: 101674-5

Canadian Compliance Requirements (RSS-102): RF Exposure Evaluation Limits Occupational / Controlled Exposure: Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.003-10 170 180 -- Instantaneous 0.1-10 -- 1.6 / f -- 6 1.29-10 193 / f0.5 -- -- 6 10-20 61.4 0.163 10 6 20-48 129.8 / f0.5 0.3444 / f0.25 44.72 / f0.5 6 48-100 49.33 0.1309 6.455 6 100-6000 15.60 f0.25 0.04138 f0.25 0.6455 f0.5 6 6000-15000 137 0.364 50 6 15000-150,000 137 0.364 50 616000/ f1.2 150,000-300,000 0.354 f0.5 9.40x10-4 f0.5 3.33x10-4 f 616000/ f1.2 RF Exposure Evaluation Limits General Population / Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.003-10 83 90 -- Instantaneous 0.1-10 -- 0.73 / f -- 6 1.1-10 87 / f0.5 -- -- 6 10-20 27.46 0.0728 2 6 20-48 58.07 / f0.25 0.1540 / f0.25 8.944 / f0.5 6 48-300 22.06 0.05852 1.291 6 300-6000 3.142 f0.3417 0.008335 f0.3417 0.02619 f0.6834 6 6000-15000 61.4 0.163 10 6 15000-150,000 61.4 0.163 10 616000/ f1.2 150,000-300,000 0.158 f0.5 4.21x10-4 f0.5 6.67x10-5 f 616000/ f1.2 Page 15 of 19 Report No: 101674-5

Stand-Alone Evaluation Exemption Levels: Exemption Limits (mW) at Separation Distance (mm) Freq(MHz) ≤5 10 15 20 25 30 35 40 45 ≥50 ≤300 71 101 132 162 193 223 254 284 315 345 450 52 70 88 106 123 141 159 177 195 213 835 17 30 42 55 67 80 92 105 117 130 1900 7 10 18 34 60 99 153 225 316 431 2450 4 7 15 30 52 83 123 173 235 309 3500 2 6 16 32 55 86 124 170 225 290 5800 1 6 15 27 41 56 71 85 97 106 Stand-Alone Evaluation Exemption Levels: Frequency (MHz) RF Exposure Exemption Limit (mW) <20 1000 20-48 22480 / f0.5 48-300 600 300-6000 1310 f0.6834 ≥6000 5000 General2 Comparison of FCC and IC Exemption Limits 2 Non-Exhaustive Page 16 of 19 Report No: 101674-5

Australian Radiation Protection and Nuclear Safety Agency Requirements (ARPANSA): RF Exposure Evaluation Limits Occupational / Controlled Exposure: Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.1 – 1.0 614 1.63/f --- 6 1.0-10 614/f 1.63/f 1000/f2 6 10-400 61.4 0.163 10 6 400-2000 3.07 * f0.5 0.00814 * f0.5 f/40 6 2000-10,000 137 0.36 50 6 10,000 – 300,000 137 0.36 50 9.6x104 / f1.05 RF Exposure Evaluation Limits General Population / Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.10-0.15 86.8 4.86 --- 6 0.150-1.0 86.8 0.729/f -- 6 1.0-10 86.8/f0.5 0.729/f --- 6 10-400 27.4 0.0729 2 6 400-2000 1.37 f0.5 0.00364*f0.5 f/200 6 2000-10,000 61.4 0.163 10 6 10,000 – 300,000 61.4 0.163 10 9.6x104 / f1.05 *Power density limit applicable >100MHz Stand-Alone Evaluation Exemption Levels: Occupational Exposure: 100mW Portable - General Public: 20mW Mobile – General Public: Separation distance >20cm and power < ARPANSA RPS3 Table S2 Or according to ARPANSA RPS3 Table S1 Table S2 Operating Frequency Nominal Mean Power Output (MHz) (W) 0.1-450 7 450-2500 3150 / f Page 17 of 19 Report No: 101674-5

European Union Compliance Requirements (ICNIRP): RF Exposure Evaluation Limits Occupational / Controlled Exposure: Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.00082-0.065 610 24.4 --- 6 0.065-1.0 610 1.6/f --- 1.0-10 610/f 1.6/f --- 6 10-400 61 0.16 10 6 400-2000 3.0 * f0.5 0.008 * f0.5 f/40 6 2000-300,000 137 0.36 50 6 RF Exposure Evaluation Limits General Population / Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (W/m2) (minutes) 0.003-0.150 87 5.0 --- 6 0.150-1.0 87 0.73/f -- 6 1.0-10 87/f0.5 0.73/f --- 6 10-400 28 0.073 2 6 400-2000 1.375 f0.5 0.0037*f0.5 f/200 6 2000-300,000 61 0.16 10 6 *Power density limit applicable >100MHz Stand-Alone Evaluation Exemption3 Levels: Head / Body: 20mW Extremity: 40mW 3 EN 62479 Annex A, General Public Page 18 of 19 Report No: 101674-5

APPENDIX C - References 1. ACMA Radiocommunications (Electromagnetic Radio – Human Exposure) Standard, 2014. 2. AS/NZS 2772.2, Radiofrequency fields – Principles and method of measurement and computation – 3 kHz to 300 GHz, 2011. 3. Australian Radiation Protection and Nuclear Safety Agency, ARPANSA RPS 3, Maximum Exposure Levels to Radiofrequency Fields 3 kHz to 300 GHz, 2002 (&Errata, 2003). 4. New Zealand Standard, NZS 2772.1, Radiofrequency Fields Part 1: Maximum Exposure Levels 3 kHz to 300 GHz, 2009. 5. Federal Communications Commission Knowledge Database (KDB) Publication 447498, “What are the RF exposure requirements and procedures for mobile and portable devices?” As in effect on the issue date of this report. 6. Title 47 Code of Federal Regulations, Part 1.1310, “Radiofrequency radiation exposure limits.” As in effect on the issue date of this report. 7. Title 47 Code of Federal Regulations, Part 2.1091, “Radiofrequency radiation exposure evaluation: mobile devices.” As in effect on the issue date of this report. 8. ANSI C95.1 (2005) IEEE Standard for Safety Level with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3kHz to 300 GHz, 2005. 9. Health Canada Safety Code 6 Limits of Human Exposure to Radiofrequency Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz, 2015. 10. Industry Canada GL-01 Guidelines for the Measurement of Radio Frequency Fields at Frequencies From 3 kHz to 300 GHz, Issue 3, March 2015. 11. Industry Canada RSS-102 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands), Issue 5, March 2015. 12. EC Council Recommendation 1999/519/EC “On the limitation of exposure of the general public to electromagnetic fields (0Hz to 300GHz),” (1999). 13. European Committee for Electrotechnical Standardization. European Normative, EN 62311 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz to 300 GHz), 2008. 14. European Committee for Electrotechnical Standardization. European Normative, EN 62479 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz), 2010. 15. International Commission on Non-Ionizing Radiation Protection. Guidelines for Limiting Exposure to Time- Varying Electric, Magnetic, and Electromagnetic Fields (up to 300 GHz). Health Physics 74 (4): 494-522; 1998. 16. International Commission on Non-Ionizing Radiation Protection Statement on the "Guidelines for limiting exposure to time-varying electric, magnetic and electromagnetic fields (up to 300 GHz). Health Physics 97(3):257-259, 2009. Page 19 of 19 Report No: 101674-5


Document Created: 2019-03-25 08:09:43
Document Modified: 2019-03-25 08:09:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC