Test report

FCC ID: EMJHSAP001MP

Test Report

Download: PDF
FCCID_4246701

FCC Test Report Report No.: RF190222D16 FCC ID: EMJHSAP001MP Test Model: HSA-P001MP Received Date: Feb. 22, 2019 Test Date: Mar. 7 ~ 11, 2019 Issued Date: Mar. 14, 2019 Applicant: PRIMAX ELECTRONICS LTD. Address: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. FCC Registration / Designation Number: 198487 / TW2021 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF190222D16 Page No. 1 / 31 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 6 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 7 3.3 Description of Support Units ............................................................................................................... 8 3.3.1 Configuration of System under Test .................................................................................................... 8 3.4 General Description of Applied Standards .......................................................................................... 8 4 Test Types and Results ........................................................................................................................ 9 4.1 Radiated Emission and Bandedge Measurement............................................................................... 9 4.1.1 Limits of Radiated Emission and Bandedge Measurement ................................................................ 9 4.1.2 Test Instruments ................................................................................................................................ 10 4.1.3 Test Procedures.................................................................................................................................. 11 4.1.4 Deviation from Test Standard ............................................................................................................. 11 4.1.5 Test Set Up ........................................................................................................................................ 12 4.1.6 EUT Operating Conditions................................................................................................................. 12 4.1.7 Test Results ....................................................................................................................................... 13 4.2 Conducted Emission Measurement .................................................................................................. 23 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 23 4.2.2 Test Instruments ................................................................................................................................ 23 4.2.3 Test Procedures................................................................................................................................. 24 4.2.4 Deviation from Test Standard ............................................................................................................ 24 4.2.5 Test Setup .......................................................................................................................................... 24 4.2.6 EUT Operating Conditions................................................................................................................. 24 4.2.7 Test Results ....................................................................................................................................... 25 4.3 Channel Bandwidth ........................................................................................................................... 27 4.3.1 Test SetUp ......................................................................................................................................... 27 4.3.2 Test Instruments ................................................................................................................................ 27 4.3.3 Test Procedure .................................................................................................................................. 27 4.3.4 Deviation from Test Standard ............................................................................................................ 27 4.3.5 EUT Operating Conditions................................................................................................................. 27 4.3.6 Test Results ....................................................................................................................................... 28 5 Pictures of Test Arrangements .......................................................................................................... 30 Appendix – Information of the Testing Laboratories ................................................................................. 31 Report No.: RF190222D16 Page No. 2 / 31 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF190222D16 Original release Mar. 14, 2019 Report No.: RF190222D16 Page No. 3 / 31 Report Format Version: 6.1.1

1 Certificate of Conformity Product: OMEN Outpost Mousepad with Qi Wireless Charging Brand: hp Test Model: HSA-P001MP Sample Status: Engineering sample Applicant: PRIMAX ELECTRONICS LTD. Test Date: Mar. 7 ~ 11, 2019 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.209) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Mar. 14, 2019 Annie Chang / Senior Specialist Approved by : , Date: Mar. 14, 2019 Rex Lai / Associate Technical Manager Report No.: RF190222D16 Page No. 4 / 31 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.209) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -5.83 dB at 0.15000 MHz 15.215 Channel Bandwidth Measurement Meet the requirement of limit. 15.209 Radiated Emission Test Pass Minimum passing margin is -8.45 dB at 191.166 MHz Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.79 dB 9kHz ~ 30MHz 2.38 dB Radiated Emissions up to 1 GHz 30MHz ~ 1000MHz 5.54 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF190222D16 Page No. 5 / 31 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product OMEN Outpost Mousepad with Qi Wireless Charging Brand hp Test Model HSA-P001MP Sample Status Engineering sample Input: 5Vdc, 3A, Rating Output: 5W Modulation Type FSK Operating Frequency 111-148kHz Antenna Type Coil antenna Field Strength 79.00dBuV/m Dimensions 14.86cm2 (diameter = 435mm) Accessory Device USB-C to two USB-A Dongle (with two USB cables (0.15m each)) Data Cable Supplied Shielded USB type C cable (1.2m) attached on EUT Maximum Power Output from 5W the Charging Coil Note: 1. The EUT is an OMEN Outpost Mousepad with Qi Wireless Charging with Qi charging function. 2. EUT has been pre-tested under following test modes, and test mode 1 was the worst case for final test. Mode Test Condition 1 EUT Link to System (via USB Type C cable) 2 EUT Link to System (via USB-C to two USB-A Dongle) 3. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. 3.2 Description of Test Modes The following test frequencies are provided to this EUT: Operating Frequency (kHz) Tested Frequency (kHz) Mode 111-148 143 Charging Mode with Full Load 111-148 147 Standby Mode Report No.: RF190222D16 Page No. 6 / 31 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE<1G PLC CBW A √ √ √ Charging Mode with Full Load B √ √ √ Standby Mode Where RE<1G: Radiated Emission below 1GHz PLC: Power Line Conducted Emission CBW: Channel Bandwidth Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Operating Frequency (kHz) Tested Frequency (kHz) A 111-148 143 B 111-148 147 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Operating Frequency (kHz) Tested Frequency (kHz) A 111-148 143 Channel Bandwidth Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Operating Frequency (kHz) Tested Frequency (kHz) A 111-148 143 B 111-148 147 Test Condition: Applicable To Environmental Conditions Input Power Tested by RE<1G 24 deg. C, 71% RH 120Vac, 60Hz (System) Ian Chang PLC 25 deg. C, 75% RH 120Vac, 60Hz (System) Dalen Dai CBW 25 deg. C, 76% RH 120Vac, 60Hz (System) Saxon Lee Report No.: RF190222D16 Page No. 7 / 31 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Load N/A N/A N/A N/A Supplied by client B. Notebook PC Lenovo 20L6-S4GW00 PF1EZSA2 N/A Provided by Lab Note: All power cords of the above support units are non-shielded (1.8m). ID Descriptions Qty. Length (m) Shielding (Yes/No) Cores (Qty.) Remarks 1. USB Type C cable 1 1.2 N 0 Supplied by client Note: The core(s) is(are) originally attached to the cable(s). 3.3.1 Configuration of System under Test For Mode A : Load (A) 1 USB Notebook PC (B) USB Type C EUT 120Vac For Mode B: 1 USB Notebook PC (B) USB Type C EUT 120Vac 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.209) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF190222D16 Page No. 8 / 31 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement For Frequency Below 30MHz Frequency Field Strength (dBuV/m) Measurement Distance (MHz) uV/m dBuV/m (meters) 0.009 – 0.490 2400 / F (kHz) 48.52-13.80 300 0.490 – 1.705 24000 / F (kHz) 33.80-22.97 30 1.705 – 30.0 30 29.54 30 For Frequency Between 30-1000MHz Frequency Class A (at 10m) Class B (at 3m) (MHz) uV/m dBuV/m uV/m dBuV/m 30-88 90 39.1 100 40.0 88-216 150 43.5 150 43.5 216-960 210 46.4 200 46.0 Above 960 300 49.5 500 54.0 Report No.: RF190222D16 Page No. 9 / 31 Report Format Version: 6.1.1

4.1.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL HP Preamplifier 8447D 2432A03504 Feb. 20, 2019 Feb. 19, 2020 HP Preamplifier 8449B 3008A01201 Feb. 21, 2019 Feb. 20, 2020 MITEQ Preamplifier AMF-6F-260400-33-8P 892164 Feb. 20, 2019 Feb. 19, 2020 Agilent N9038A MY51210129 Mar. 05, 2019 Mar. 04, 2020 TEST RECEIVER Schwarzbeck Antenna VULB 9168 139 Nov. 26, 2018 Nov. 25, 2019 Schwarzbeck Antenna VHBA 9123 480 May 19, 2017 May 18, 2019 Schwarzbeck Horn BBHA-9170 212 Nov. 25, 2018 Nov. 24, 2019 Antenna Schwarzbeck Horn BBHA 9120-D1 D130 Nov. 25, 2018 Nov. 24, 2019 Antenna ADT. Turn Table TT100 0306 NA NA ADT. Tower AT100 0306 NA NA Software Radiated_V7.6.15.9.5 NA NA NA SUHNER RF cable SF102 Cable-CH6-01 Aug. 13, 2018 Aug. 12, 2019 With 4dB PAD SUHNER RF cable SF102 Cable-CH8-3.6m Aug. 13, 2018 Aug. 12, 2019 With 3/4dB PAD KEYSIGHT MIMO Powermeasurement Test U2021XA U2021XA-001 Jun. 4, 2018 Jun. 3, 2019 set KEYSIGHT N9030A MY54490260 Aug. 3, 2018 Aug. 2, 2019 Spectrum Analyzer Loop Antenna EMCI LPA600 270 Aug. 11, 2017 Aug. 10, 2019 EMCO Horn Antenna 3115 00028257 Nov. 25, 2018 Nov. 24, 2019 Highpass filter WHK 3.1/18G-10SS SN 8 NA NA Wainwright Instruments ROHDE & SCHWARZ FSV40 101042 Sep. 27, 2018 Sep. 26, 2019 Spectrum Analyzer NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. Report No.: RF190222D16 Page No. 10 / 31 Report Format Version: 6.1.1

4.1.3 Test Procedures For Radiated emission below 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF190222D16 Page No. 11 / 31 Report Format Version: 6.1.1

4.1.5 Test Set Up For Radiated emission below 30MHz EUT& 3m Loop antenna Support Units Turn Table 80cm Ground Plane Test Receiver For Radiated emission 30MHz to 1GHz Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Test Mode A: a. Connect the EUT to Notebook PC. b. Put the Load on the EUT (wireless charging) during the test. Test Mode B: a. Connect the EUT to Notebook PC. b. Set the EUT under standby condition. Report No.: RF190222D16 Page No. 12 / 31 Report Format Version: 6.1.1

4.1.7 Test Results Below 30MHz Data: Charging Mode Test Frequency 143kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode A Antenna Polarity & Test Distance: Loop Antenna Open At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.143 75.70 QP 104.50 -28.80 1.00 1 56.69 19.01 2 0.429 53.88 QP 94.95 -41.07 1.00 159 43.79 10.09 3 0.715 44.34 QP 70.52 -26.18 1.00 58 37.35 6.99 4 1.001 38.62 QP 67.60 -28.98 1.00 211 33.48 5.14 5 1.287 35.97 QP 65.41 -29.44 1.00 274 31.49 4.48 6 1.573 32.53 QP 63.67 -31.14 1.00 322 28.70 3.83 7 1.859 31.72 QP 69.54 -37.82 1.00 360 28.55 3.17 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 13 / 31 Report Format Version: 6.1.1

Test Frequency 143kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode A Antenna Polarity & Test Distance: Loop Antenna Close At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.143 68.97 QP 104.50 -35.53 1.00 110 49.96 19.01 2 0.429 46.89 QP 94.95 -48.06 1.00 150 36.80 10.09 3 0.715 34.69 QP 70.52 -35.83 1.00 321 27.70 6.99 4 1.001 33.14 QP 67.60 -34.46 1.00 206 28.00 5.14 5 1.287 30.56 QP 65.41 -34.85 1.00 157 26.08 4.48 6 1.573 29.18 QP 63.67 -34.49 1.00 278 25.35 3.83 7 1.859 27.14 QP 69.54 -42.40 1.00 360 23.97 3.17 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 14 / 31 Report Format Version: 6.1.1

Test Frequency 143kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode A Antenna Polarity & Test Distance: Loop Antenna Ground-parallel At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.143 72.79 QP 104.50 -31.71 1.00 299 53.78 19.01 2 0.429 51.44 QP 94.95 -43.51 1.00 288 41.35 10.09 3 0.715 43.35 QP 70.52 -27.17 1.00 223 36.36 6.99 4 1.001 37.64 QP 67.60 -29.96 1.00 174 32.50 5.14 5 1.287 33.34 QP 65.41 -32.07 1.00 104 28.86 4.48 6 1.573 31.73 QP 63.67 -31.94 1.00 57 27.90 3.83 7 1.859 30.20 QP 69.54 -39.34 1.00 6 27.03 3.17 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 15 / 31 Report Format Version: 6.1.1

Standby Mode Test Frequency 147kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode B Antenna Polarity & Test Distance: Loop Antenna Open At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.147 76.64 QP 104.26 -27.62 1.00 347 57.85 18.79 2 0.441 52.67 QP 94.72 -42.05 1.00 337 42.73 9.94 3 0.735 42.92 QP 70.28 -27.36 1.00 164 36.09 6.83 4 1.029 36.20 QP 67.36 -31.16 1.00 252 31.13 5.07 5 1.323 31.26 QP 65.17 -33.91 1.00 302 26.85 4.41 6 1.617 28.76 QP 63.43 -34.67 1.00 242 25.03 3.73 7 1.911 26.97 QP 69.54 -42.57 1.00 91 23.91 3.06 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 16 / 31 Report Format Version: 6.1.1

Test Frequency 147kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode B Antenna Polarity & Test Distance: Loop Antenna Close At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.147 61.52 QP 104.26 -42.74 1.00 360 42.73 18.79 2 0.441 44.57 QP 94.72 -50.15 1.00 336 34.63 9.94 3 0.735 37.92 QP 70.28 -32.36 1.00 202 31.09 6.83 4 1.029 33.86 QP 67.36 -33.50 1.00 151 28.79 5.07 5 1.323 32.70 QP 65.17 -32.47 1.00 72 28.29 4.41 6 1.617 31.54 QP 63.43 -31.89 1.00 11 27.81 3.73 7 1.911 30.02 QP 69.54 -39.52 1.00 0 26.96 3.06 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 17 / 31 Report Format Version: 6.1.1

Test Frequency 147kHz Detector Function Quasi-Peak Frequency Range 9 kHz ~ 30 MHz Test Mode B Antenna Polarity & Test Distance: Loop Antenna Ground-parallel At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *0.147 79.00 QP 104.26 -25.26 1.00 360 60.21 18.79 2 0.441 51.15 QP 94.72 -43.57 1.00 176 41.21 9.94 3 0.735 43.23 QP 70.28 -27.05 1.00 359 36.40 6.83 4 1.029 38.94 QP 67.36 -28.42 1.00 360 33.87 5.07 5 1.323 33.88 QP 65.17 -31.29 1.00 360 29.47 4.41 6 1.617 31.65 QP 63.43 -31.78 1.00 310 27.92 3.73 7 1.911 29.00 QP 69.54 -40.54 1.00 343 25.94 3.06 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. “ * “: Fundamental frequency. 6. Loop antenna was used for all radiated emission below 30MHz. 7. Limit @3m=Limit@300m+40log(300 / 3)=Limit@300m+80 8. Limit @3m=Limit@30m+40log(30 / 3)=Limit@30m+40 Report No.: RF190222D16 Page No. 18 / 31 Report Format Version: 6.1.1

Below 1GHz Data: Charging Mode Test Frequency 143kHz Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode A Antenna Polarity & Test Distance: Horizontal At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 123.945 23.21 QP 43.50 -20.29 1.57 H 146 31.98 -8.77 2 190.875 34.45 QP 43.50 -9.05 1.52 H 146 43.47 -9.02 3 257.029 31.23 QP 46.00 -14.77 2.39 H 177 37.93 -6.70 4 352.137 27.96 QP 46.00 -18.04 2.25 H 114 32.18 -4.22 5 449.913 27.14 QP 46.00 -18.86 1.82 H 190 29.15 -2.01 6 537.843 27.59 QP 46.00 -18.41 1.06 H 306 28.31 -0.72 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF190222D16 Page No. 19 / 31 Report Format Version: 6.1.1

Test Frequency 143kHz Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode A Antenna Polarity & Test Distance: Vertical At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 52.261 26.11 QP 40.00 -13.89 1.32 V 121 33.28 -7.17 2 118.561 24.55 QP 43.50 -18.95 1.60 V 134 33.80 -9.25 3 189.759 28.47 QP 43.50 -15.03 1.26 V 69 37.42 -8.95 4 261.345 27.51 QP 46.00 -18.49 1.05 V 94 33.99 -6.48 5 458.546 27.39 QP 46.00 -18.61 1.45 V 162 29.29 -1.90 6 529.162 27.19 QP 46.00 -18.81 1.67 V 112 28.01 -0.82 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF190222D16 Page No. 20 / 31 Report Format Version: 6.1.1

Standby Mode Test Frequency 147kHz Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode B Antenna Polarity & Test Distance: Horizontal At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 43.095 24.18 QP 40.00 -15.82 2.34 H 61 31.60 -7.42 2 123.993 24.13 QP 43.50 -19.37 2.10 H 122 32.90 -8.77 3 191.166 35.05 QP 43.50 -8.45 2.09 H 127 44.07 -9.02 4 257.077 29.42 QP 46.00 -16.58 1.82 H 169 36.12 -6.70 5 365.911 28.14 QP 46.00 -17.86 1.76 H 109 32.04 -3.90 6 519.705 27.51 QP 46.00 -18.49 1.28 H 202 28.50 -0.99 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF190222D16 Page No. 21 / 31 Report Format Version: 6.1.1

Test Frequency 147kHz Detector Function Quasi-Peak Frequency Range 30 MHz ~ 1GHz Test Mode B Antenna Polarity & Test Distance: Vertical At 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 52.892 26.71 QP 40.00 -13.29 1.64 V 103 33.86 -7.15 2 123.945 23.87 QP 43.50 -19.63 1.06 V 349 32.64 -8.77 3 188.789 27.97 QP 43.50 -15.53 1.42 V 52 36.91 -8.94 4 257.271 28.21 QP 46.00 -17.79 1.55 V 203 34.90 -6.69 5 391.810 24.20 QP 46.00 -21.80 1.72 V 253 27.58 -3.38 6 495.794 26.23 QP 46.00 -19.77 1.32 V 155 27.56 -1.33 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value Report No.: RF190222D16 Page No. 22 / 31 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due ROHDE & SCHWARZ ESR3 102414 Jan. 17, 2019 Jan. 16, 2020 TEST RECEIVER ROHDE & SCHWARZ Artificial Mains ENV216 101197 May 23, 2018 May 22, 2019 Network (for EUT) LISN With Adapter (for EUT) AD10 C10Ada-002 May 23, 2018 May 22, 2019 ROHDE & SCHWARZ Artificial Mains ESH3-Z5 100218 Nov. 30, 2018 Nov. 29, 2019 Network (for peripherals) SCHWARZBECK NNLK8129 8129229 May 3, 2018 May 2, 2019 Artificial Mains Network (For EUT) Software Cond_V7.3.7.4 NA NA NA RF cable (JYEBAO) 5D-FB Cable-C10.01 Feb. 13, 2019 Feb. 12, 2020 With 10dB PAD SUHNER Terminator 65BNC-5001 E1-011484 May 8, 2018 May 7, 2019 (For ROHDE & SCHWARZ LISN) ROHDE & SCHWARZ ESH3-Z5 100220 Nov. 21, 2018 Nov. 20, 2019 Artificial Mains Network (For TV EUT) LISN With Adapter (for TV EUT) 100220 N/A Nov. 21, 2018 Nov. 20, 2019 Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. 10. Report No.: RF190222D16 Page No. 23 / 31 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as item 4.1.6. Report No.: RF190222D16 Page No. 24 / 31 Report Format Version: 6.1.1

4.2.7 Test Results Charging Mode Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 9.66 50.51 34.93 60.17 44.59 66.00 56.00 -5.83 -11.41 2 0.20474 9.67 37.42 16.77 47.09 26.44 63.42 53.42 -16.33 -26.98 3 0.27844 9.68 32.45 17.00 42.13 26.68 60.86 50.86 -18.73 -24.18 4 0.45498 9.71 22.09 13.15 31.80 22.86 56.78 46.78 -24.98 -23.92 5 4.46083 9.84 22.12 14.03 31.96 23.87 56.00 46.00 -24.04 -22.13 6 9.17588 9.93 23.12 16.61 33.05 26.54 60.00 50.00 -26.95 -23.46 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF190222D16 Page No. 25 / 31 Report Format Version: 6.1.1

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Test Mode A Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 9.67 48.21 31.24 57.88 40.91 66.00 56.00 -8.12 -15.09 2 0.19301 9.69 41.15 22.33 50.84 32.02 63.91 53.91 -13.07 -21.89 3 0.26730 9.70 31.34 12.05 41.04 21.75 61.20 51.20 -20.16 -29.45 4 1.61826 9.79 13.46 8.17 23.25 17.96 56.00 46.00 -32.75 -28.04 5 4.65242 9.85 23.49 15.65 33.34 25.50 56.00 46.00 -22.66 -20.50 6 4.87920 9.86 22.70 14.60 32.56 24.46 56.00 46.00 -23.44 -21.54 7 9.03512 9.95 22.10 15.21 32.05 25.16 60.00 50.00 -27.95 -24.84 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF190222D16 Page No. 26 / 31 Report Format Version: 6.1.1

4.3 Channel Bandwidth 4.3.1 Test SetUp EUT& 3m Loop antenna Support Units Turn Table 80cm Ground Plane Test Receiver 4.3.2 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.3 Test Procedure a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter Semi-anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. Then the Loop antenna was rotated 360 degrees to determine the position of the highest radiation. b. The antenna is a broadband loop antenna, which is fixed of a 1m height above the ground, and set away from 3m to the EUT to find the disturbance reading on each frequency. c. The test-receiver system was set to Quasi-peak detect function and specified bandwidth. 4.3.4 Deviation from Test Standard No deviation. 4.3.5 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously. Report No.: RF190222D16 Page No. 27 / 31 Report Format Version: 6.1.1

4.3.6 Test Results Mode A: Frequency (kHz) 20dB Bandwidth (kHz) 143 0.775 Spectrum Plot Of Worst Value Report No.: RF190222D16 Page No. 28 / 31 Report Format Version: 6.1.1

Mode B: Frequency (kHz) 20dB Bandwidth (kHz) 147 0.775 Spectrum Plot Of Worst Value Report No.: RF190222D16 Page No. 29 / 31 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF190222D16 Page No. 30 / 31 Report Format Version: 6.1.1

Appendix – Information of the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Lin Kou EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF190222D16 Page No. 31 / 31 Report Format Version: 6.1.1


Document Created: 2019-04-22 21:10:03
Document Modified: 2019-04-22 21:10:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC